Polyisobutylene-containing block polymers by sequential monomer addition. IV. New triblock thermoplastic elastomers comprising high Tg styrenic glassy segments: Synthesis,characterization and physical properties

New linear triblock thermoplastic elastomers (TPEs) comprising a rubbery polyisobutylene (PIB) midblock flanked by two glassy endblocks of various styrenic polymers have been synthesized by living carbocationic polymerization by sequential monomer addition. First isobutylene (IB) was polymerized by a bifunctional tert-ether (dicumyl methyl ether) initiator in conjunction with TiCl₄ coinitiator in CH₃Cl/methylcyclohexane (MeCHx) (40/60 v/v) solvent mixtures at ?80°C. After the living narrow molecular weight distribution PIB midblock ( = 1.1–1.2) has reached the desired molecular weight, the styrenic monomers together with an electron pair donor (ED) and a proton trap (di-tert-butylpyridine, DtBP) were added to start the blocking of the glassy segments from the living ⊕PIB⊕ chain ends. While p-methylstyrene (pMeSt), p-t-butylstyrene (ptBuSt) and indene (In) gave essentially 100% blocking to the corresponding glassy endblocks, the blocking of 2,4,6-trimethylstyrene (TMeSt) and α-methylstyrene (αMeSt) were ineffective. Uncontrolled initiation by protic impurities was prevented by the use of DtBP. In the simultaneous presence of DtBP and the strong ED N,N-dimethylacetamide (DMA), TPEs with good mechanical properties (10–20 MPa tensile strength, 300–600% elongation) were prepared. The products exhibit a low and a high temperature T_g characteristic of phase separated rubbery and glassy domains. The service temperature of these new TPEs exceeds that of PSt–PIB–PSt triblock copolymers due to the higher T_gs (PpMeSt = 108, PptBuSt = 142 and PIn = 220–240°C) of the outer blocks. The T_g of the glassy blocks can be regulated by copolymerizing two styrene derivatives; a triblock copolymer with outer blocks of poly(pt-butylstyrene-co-indene) showed a single glassy transition T_g = +165°C, i.e., in between that of PptBuSt and PIn. Virgin TPEs have been repeatedly compression molded without deterioration of physical properties. The high melt flow index obtained with a TPE containing PptBuSt endblocks suggests superior processability relative to those with PSt end-blocks. The tensile strength retention at 60°C of the former TPE is far superior to that of a PSt–PIB–PSt triblock of similar composition.     

Polyisobutylene-containing block polymers by sequential monomer addition. I. The living carbocationic polymerization of styrene

The living carbocationic polymerisation of styrene (St) has been investigated by the 2-chloro-2,4,4-trimethylpentane (TMPCI)/TiCl₄ initiating system in the presence of various additives such as electron pair donors (ED_s) and the proton trap 2,6-di-tert-butylpyridine (DtBP) by the use of the mixed solvent CH₃Cl/methyl-cyclohexane (MCHx) (40/60 v/v) at ?80°C under conventional laboratory conditions. The TMPCl/TiCl₄ system in the absence of additives produces ill-defined bimodal molecular weight distribution (MWD) polymers. Much better defined polystyrenes (PSt) can be obtained in the presence of EDs, such as N,N-dimethylacetamide (DMA) and hexamethylphosphoramide (HMPA). Monomer depletion should be avoided to prevent intra- or intermolecular alkylation yielding indanyl end groups or branched polymers, respectively. In the combined presence of an ED and the proton trap, i.e., DMA + DtBP, the living polymerization of St has been achieved and thus the foundations for the carbocationic synthesis of PSt block polymers by sequential monomer addition have been laid.     

Polyisobutylene-containing block polymers by sequential monomer addition. X. Synthesis of poly(α-methylstyrene-b-isobutylene-b-α-methylstyrene) thermoplastic elastomers

Preparatory to triblock synthesis experiments, the cationic polymerization of α-methylstyrene (αMeSt) was investigated using the 2-chloro-2,4,4-trimethylpentane (TMPCI)/TiCl₄ initiating system in the presence of triethylamine (Et₃N) as electron donor (ED) and CH₃Cl/n-hexane mixed solvent in the ?80 to ?40°C range. Conversions are influenced by temperature, [TiCl₄], [Et₃N], and [αMeSt]. The polymerization of αMeSt is living at ?80°C: Both termination and chain transfer to monomer are frozen out, however, initiation is slow relative to propagation. Highly syndiotactic (>94%) Pα Mest was obtained. At?60deg;C initiator efficiency is ca. 100%, but termination becomes evident. Et₃N may act both as Ed and as proton scavenger. Novel poly(α-methystyrene-b-isobutylene-b-α-methylstyrene) (PαMeSt-PIB-PαMeSt) triblocks have been synthesized by adding αMeSt to biliving polyisobutylene carbocations (⊕PIB⊕) in the ?80 to ?40°C range. The effects of temperature, solvent polarity, and [Et₃N] on the block copolymerization have been investigated. At ?80°C, the rate of crossover from ⊕PIB⊕ to αMeSt is lower than that of propagation of PαMeSt⊕, so that the triblock is contaminated by PIB and PIB-b-PαMeSt. At ?60°C, crossover occurs preferentially. The rate of propagation relative to that of crossover is also reduced by lowering the solvent polarity and increasing the [Et₃N]. High crossover efficiency and blocking efficiency can be obtained under optimum blocking conditions. The triblocks are novel thermoplastic elastomers (TPEs). © 1994 John Wiley & Sons, Inc.     

Synthesis and characterization of novel dendritic (arborescent,hyperbranched) polyisobutylene–polystyrene block copolymers

The synthesis of novel arborescent (arb; randomly branched, “tree‐like,” and often called “hyperbranched”) block copolymers comprised of rubbery polyisobutylene (PIB) and glassy polystyrene (PSt) blocks (arb‐PIB‐b‐PSt) is described. The syntheses were accomplished by the use of arb‐PIB macroinitiators (prepared by the use of 4‐(2‐methoxyisopropyl) styrene inimer) in conjunction with titanium tetrachloride (TiCl₄). The effect of reaction conditions on blocking of St from arb‐PIB was investigated. Purified block copolymers were characterized by ¹H NMR spectroscopy and Size Exclusion Chromatography (SEC). arb‐PIB‐b‐PSt with 11.7–33.8 wt % PSt and M_n = 468,800–652,900 g/mol displayed thermoplastic elastomeric properties with 3.6–8.7 MPa tensile strength and 950–1830% elongation. Samples with 26.8–33.8 wt % PSt were further characterized by Atomic Force Microscopy (AFM), which showed phase‐separated mixed spherical/cylindrical/lamellar PSt phases irregularly distributed within the continuous PIB phase. Dynamic Mechanical Thermal Analysis (DMTA) and solvent swelling of arb‐PIB‐b‐PSt revealed unique characteristics, in comparison with a semicommercial PSt‐b‐PIB‐b‐PSt block copolymer. The number of aromatic branching points of the arb‐PIB macroinitiator, determined by selective destruction of the linking sites, agreed well with that calculated from equilibrium swelling data of arb‐PIB‐b‐PSt. This method for the quantitative determination of branching sites might be generally applicable for arborescent polymers. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1811–1826, 2005     

Novel block ionomers II. Synthesis and characterization of polyisobutylene‐based block cationomers

Various novel block cationomers consisting of polyisobutylene (PIB) and poly[2‐(dimethylamino)ethyl methacrylate] (PDMAEMA) segments were synthesized and characterized. The specific targets were various molecular weight diblocks (PIB‐b‐PDMAEMA⁺) and triblocks (PDMAEMA⁺‐b‐PIB‐b‐PDMAEMA⁺), with the PIB blocks in the DP_n = 50–200 range (number‐average molecular weight = 3,000–9000 g/mol) connected to blocks of PDMAEMA⁺ cations in the DP_n = 5–20 range (where DP is the number‐average degree of polymerization). The overall synthetic strategy for the preparation of these block cationomers had four steps: (1) synthesis by living cationic polymerization of mono‐ and diallyltelechelic polyisobutylenes, (2) end‐group transformation to obtain PIBs fitted with termini capable of mediating the atom transfer radical polymerization (ATRP) of DMAEMA, (3) ATRP of DMAEMA, and (4) quaternization of PDMAEMA to PDMAEMA ⁺I^? by CH₃I. Scheme 1 shows the microarchitecture and outlines the synthesis route. Kinetic and model experiments provided guidance for developing convenient synthesis methods. The microarchitecture of PIB–PDMAEMA di‐ and triblocks and the corresponding block cationomers were confirmed by ¹H NMR and FTIR spectroscopy and solubility studies. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3679–3691, 2002     

Synthesis and characterization of polymethylphenylsilane–polystyrene block copolymers

Block copolymers of polymethylphenylsilane (PMPS) and polystyrene (PS) have been successfully prepared by the condensation of α,ω-dichloro-polymethylphenylsilane with polystyryl-lithium. These new materials have been characterized by UV spectroscopy, ²⁹Si-NMR, and size exclusion chromatography. These block copolymers show a good emulsifying activity to compatibilize blends of the two homopolymers (PMPS and PS). © 1993 John Wiley & Sons, Inc.     

Novel block ionomers. I. Synthesis and characterization of polyisobutylene‐based block anionomers

A series of novel block anionomers consisting of polyisobutylene (PIB) and poly(methacrylic acid) (PMAA) segments were prepared and characterized. The specific targets were various molecular weight diblocks (PIB‐b‐PMAA^?), triblocks (PMAA^?‐b‐PIB‐b‐PMAA^?), and three‐arm star blocks [Φ(PIB‐b‐PMAA^?)₃] consisting of rubbery PIB blocks with a number‐average degree of polymerization of 50–1000 (number‐average molecular weight = 3000–54,000 g/mol) connected to blocks of PMAA^? anions with a number‐average degree of polymerization of 5–20. The overall strategy for the synthesis of these constructs consisted of four steps: (1) synthesis by living cationic polymerization of t‐chloro‐monotelechelic, t‐chloro‐ditelechelic, and t‐chloro‐tritelechelic PIBs; (2) site transformation to obtain PIBs fitted with termini capable of mediating the atom transfer radical polymerization (ATRP) of tert‐butyl methacrylate (tBMA); (3) ATRP of tBMA, and (4) hydrolysis of poly(tert‐butyl methacrylate) to PMAA^?. The architectures created and the synthesis steps employed are summarized. Kinetic and model experiments greatly assisted in the development of convenient synthesis methods. The microarchitectures of the various block anionomers were confirmed by spectroscopy and other techniques. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3662–3678, 2002     

Synthesis,characterization and optical properties of graphene oxide–polystyrene nanocomposites

The synthesis of graphene oxide (GO)–polystyrene (PS) Pickering emulsions, as environment‐friendly nanostructures suitable for novel applications, has received significant attention in recent years. In this work, the synthesis and characterization of GO–PS nanocomposites through seeded emulsion polymerization and the selective light reflection properties of dry films have been reported. Amphiphilic molecule sulfonated 3‐pentadecyl phenol was used as a co‐surfactant to stabilize GO dispersions during the emulsion polymerization process. The particle size of the dispersions as measured by dynamic light scattering decreases from 540 nm, for PS without any GO, to 88 nm with 1 wt% GO content. Scanning electron microscopy studies show a uniform size distribution of the composite particles prepared with GO. The dried films show a structural color that varies with the GO content. The self‐assembly behavior of the dried film was further studied using reflectance spectroscopy, which shows a red shift of the reflectance maximum from 440 to 538 nm as the GO loading was increased from 0.2 to 0.5 wt%, respectively, indicating a different microstructure. X‐ray diffraction, transmission electron microscopy (TEM) and atomic force microscopy (AFM) were used to study the morphology and structure of the composite particles on drying. The AFM study confirms the non‐spherical shape of the particles. Thermogravimetric analysis shows improved thermal decomposition characteristics of the nanocomposite films. Copyright © 2015 John Wiley & Sons, Ltd.     

Polyarylate–polystyrene block copolymer from macro-azoinitiator: Synthesis and its thermal properties

A macro-azoinitiator containing polyarylate segment and azo group was prepared by the solution polycondensation of azobiscyanopentanoyl chloride and hydroxy-terminated polyarylates having viscosity-average molecular weights of 6200, 8100, and 12 400. These macro-azoinitiators were used in the radical polymerization of styrene to synthesize polyarylate-polystyrene block copolymers. Thermal properties measured by the differential scanning calorimetry indicated the phase separated morphology of the block copolymers except at low molecular weight of the block constituents. © 1993 John Wiley & Sons, Inc.     

Nylon 6–polyisobutylene sequential copolymers. II. Synthesis,characterization, and morphology of di-, tri-, and radial block copolymers

Nylon 6–PIB diblock, triblock, and tristar radial block copolymers have been synthesized from telechelic hydroxyl-terminated polyisobutylene, PIB(OH)_n (n = 1,2,3), by conversion of this prepolymer with hexamethylene diisocyanate (HMDI), toluene diisocyanate (TDI), N-chlorocarbonyl diisocyanate (NCCI), and oxalyl chloride (OxCl) and using the resulting materials as macroactivators for anionic caprolactam polymerization. Prepolymers with molecular weights from 6000 to 38,000 have been employed. Derivatization with NCCI and subsequent anionic caprolactam polymerization gave highest yields and blocking efficiencies. The block copolymers have been characterized by molecular weight and composition. In addition to the expected T_g and T_m characteristics of long PIB and nylon 6 segments, DSC studies showed an intermediate glass transition at ca. ?20°C. Transmission electron microscopy of di-, tri-, and radial blocks show increasing segregation and orientation of rubbery/crystalline domains. Tensile strengths and elongations of the block copolymers range from 16.5 to 41 MPa and 15 to 30%, respectively, and stress-strain diagrams show the effect of block architecture on these properties.     

Polydimethylsiloxane–vinyl block polymers. II. The synthesis and characterization of block polymers by the thermolysis of polydimethylsiloxane macroinitiators containing bis(silyl pinacolate) groups

The thermolysis of polydimethylsiloxanes containing thermally labile bis(silyl pinacolate) groups in the backbone in the presence of various vinyl monomers leads to the direct synthesis of block polymers. Depending on the monomer chosen, simple triblock or multisequence block polymers can be readily prepared. Analysis of the products of the block polymerizations using various styrenic-type monomers shows that only block polymers are obtained, i.e., no homo-polymers are formed. These block polymers display evidence of phase separation such as intense iridescence and solvent-dependent mechanical properties. The mechanical properties of these block polymers have been measured and found to be highly composition dependent. Depending on the block length and the relative portions of the hard (vinyl) and soft (polydimethylsiloxane) blocks, one can produce either thermoplastic elastomers or rubber-modified thermoplastics.     

Synthesis and characterization of amphiphilic triblock polymers by copper mediated living radical polymerization

2-Dimethylaminoethyl methacrylate (DMAEMA) and 2-diethylaminoethyl methacrylate (DEAEMA) block copolymers have been synthesized by using poly(ethylene glycol), poly(tetrahydrofuran) (PTHF) and poly(ethylene butylenes) macroinitiators with copper mediated living radical polymerization. The use of difunctional macroinitiator gave ABA block copolymers with narrow polydispersities (PDI) and controlled number average molecular weights (M_n’s). By using DMAEMA, polymerizations proceed with excellent first order kinetics indicative of well-controlled living polymerization. Online ¹H NMR monitoring has been used to investigate the polymerization of DEAEMA. The first order kinetic plots for the polymerization of DEAMA showed two different rate regimes ascribed to an induction period which is not observed for DMAEMA. ABA triblock copolymers with DMAEMA as the A blocks and PTHF or PBD as B blocks leads to amphiphilic block copolymers with M_n’s between 22 and 24 K (PDI 1.24-1.32) which form aggregates/micelles in solution. The critical aggregation concentrations, as determined by pyrene fluorimetry, are 0.07 and 0.03 g dm⁻¹ for PTHF- and PBD-containing triblocks respectively.     

Synthesis,characterization and modeling of ABC triblock terpolymers: the effect of block sequence

Four equimolar terpolymers comprising ten units from each of the monomers methoxy hexa(ethylene glycol) methacrylate (HEGMA), 2-(dimethylamino)ethyl methacrylate (DMAEMA) and methyl methacrylate (MMA) were prepared by group transfer polymerization (GTP), and characterized by gel permeation chromatography (GPC) and proton nuclear magnetic resonance (¹H NMR) spectroscopy to confirm size homogeneity and composition. These terpolymers were the three block sequence isomers, ABC, BAG and ACB, as well as the statistical isomer. Aqueous solutions of the terpolymers were characterized by dynamic light scattering and turbidimetry to determine the hydrodynamic sizes and cloud points. The results indicated micelle formation in the triblocks, and absence of micellization with the statistical terpolymer. In general, a strong dependence of the hydrodynamic size and cloud point on polymer architecture was observed. Monte Carlo simulations on non-aggregating isomeric terpolymers of similar structure also showed a strong dependence of the radius of gyration on polymer architecture.     

Novel two‐dimensional donor–acceptor conjugated polymers containing quinoxaline units: Synthesis,characterization, and photovoltaic properties

Novel two‐dimensional donor–acceptor (D–A) structured conjugated polymers, P1–P4, were designed and synthesized by introducing electron‐deficient quinoxaline as core and electron‐rich alkoxyl‐phenylenevinylene in side chains and p‐phenylenevinylene, triphenylamine, or thiophene in main chain. Benefited from the D–A structures, the polymers possess low bandgaps of 1.75 eV, 1.86 eV, 1.59 eV, and 1.58 eV for P1, P2, P3, and P4, respectively, and show broad absorption band in the visible region: the shorter wavelength absorption peak at ～400 nm ascribed to the conjugated side chains and the longer wavelength absorption peak between 500 nm and 750 nm belonging to the absorption of the conjugated main chains. Especially, the absorption band of P4 film covers the whole visible range from 300 nm to 784 nm. The power conversion efficiencies of the polymer solar cells based on P1–P4 as donor and PCBM as acceptor are 0.029%, 0.14%, 0.46%, and 0.57%, respectively, under the illumination of AM 1.5, 100 mW/cm². The polymers with the low bandgap and broad absorption band are promising photovoltaic materials. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4038–4049, 2008     

Novel fluorosilicone triblock copolymers prepared by two-step RAFT polymerization: Synthesis, characterization, and surface properties

Well-defined poly(dimethylsiloxane)-b-poly(2,2,3,3,4,4,4-heptafluorobutyl methacrylate-b-poly(styrene) (PDMS-b-PHFBMA-b-PS) triblock copolymers were prepared by two-step reversible addition-fragmentation chain transfer (RAFT) polymerization. The two-step RAFT polymerization proceeded in a controlled manner as demonstrated by the macromolecular characteristics of the blocks and corresponding polymerization kinetic data. Furthermore, surface properties and morphologies of the polymers were investigated with static water contact angle (WCA) measurement, X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM) and atomic force microscopy (AFM) which showed low surface energy and microphase-separation surfaces.     

Synthesis and characterization of branched polystyrene. Part II. Fractionation

Fractionations have been carried out by a column-elution method on mixtures of linear and branched polystyrene. These had been prepared by anionic polymerization followed by a coupling reaction to form star-shaped branched polymers. Therefore, the components of the mixture were each of narrow distribution, and their molecular weights differed from each other as multiples of the original single chain length. For single chains in the 25,000–30,000 molecular weight range, separations were accomplished in which the multiples (number of branches) were 1, 2, 4, and 6. By this means, virtually monodisperse samples of the branched polymers could be isolated.     

Diluent effects on molecular motions and glass transition in polymers. I. Polystyrene–toluene

The effects of diluent on molecular motions and glass transition in the polystyrene–toluene system was studied by means of dielectric, thermal, and NMR measurements. Three dielectric relaxations were observed between 80 and 400°K. On the basis of NMR measurements on solutions in toluene and in deuterated toluene, relaxation processes were assigned to segmental motions of polystyrene, rotations of toluene, and the local motions of polystyrene and toluene in order of appearance from the high-temperature side. The concentration dependence of the relaxation strength and of the activation energy for the primary relaxation (that at the highest temperature) show a step increment at about 50% by weight. The activation plots for the primary process were expressed by the Vogel–Tamman equation. With this equation, the temperatures at which the mean dielectric relaxation time becomes 100 sec is determined. This agrees well with the glass-transition temperature T_g and hence T_g in concentrated solution is expressed by in terms of the parameters A, B, and T₀ of the Vogel–Tamman equation. The values of A and B are, respectively, about 12 and 0.65 and independent of the concentration. The physical meaning of these parameters is discussed.     

Styrene–isoprene block copolymers. I. Synthesis and solution properties

Copolymers with a different degree of distribution of styrene and isoprene blocks are prepared by anionic polymerization. The products are characterized by means of ¹H-NMR spectroscopy, GPC, viscometry, and light scattering. The results show that the copolymers are homogeneous in molecular weight and chain composition. In the investigated selective solvents, cyclohexane and base lubricating oil, and equilibrium exists between micelle aggregates and individual polymer coils. The influence of the copolymer structure on the micellization is more pronounced in cyclohexane.     

Dithienobenzimidazole‐containing conjugated donor–acceptor polymers: Synthesis and characterization

The synthesis of two new conjugated polymers based on the relatively under‐exploited monomer, 5,8‐dibromo‐2‐[5‐(2‐hexyldecyl)‐2‐thienyl]‐1H‐dithieno[3,2‐e:2′,3′‐g]benzimidazole (dithienobenzimidazole, DTBI ), and either 4,7‐bis[4‐hexyl‐5‐(trimethylstannyl)‐2‐thienyl]‐2,1,3‐benzothiadiazole ( BTD ) or 2,6‐bis(trimethylstannyl)‐4,8‐bis(5‐(2‐ethylhexyl) thiophen‐2‐yl)benzo[1,2‐b:4,5‐b′]dithiophene ( BDT ) is described. The polymers were synthesized via Stille polycondensation and characterized by traditional methods (¹H NMR, gel‐permeation chromatography, matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry, thermal gravimetric analysis, differential scanning calorimetry, ultraviolet–visible spectroscopy, photoluminescence, and cyclic voltammetry). Prior to their synthesis, trimer structures were modeled by DFT calculations facilitating a further understanding of the systems' electronic and geometric structure. Polymers were titrated with acid and base to take advantage of their amphiprotic imidazole moiety and their optical response monitored with ultraviolet–visible spectroscopy. Finally, pristine polymer thin‐films were treated with acid and base to evaluate (de)protonation's effect on system electronics, but thin‐film degradation was encountered. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 60–69     

Ferrocene‐based organophosphorus liquid–crystalline polymers: Synthesis and characterization

Ferrocene‐containing polyphosphate and phosphonate esters were synthesized by the solution polycondensation method. The structure of the polymers was confirmed using various spectroscopic techniques. The formation of two types of chain blocks was confirmed by ³¹P NMR spectroscopy. Hot stage optical polarized microscope (HOPM) analysis revealed that all the polymers have a liquid–crystalline property. The char yields of the synthesized similar polymers were much higher than those of nonphosphorus polymers already reported in the literature. DSC analysis confirmed our predictions over the liquid–crystalline property, glass‐transition temperature, isotropization temperature, and thermal stability of the polymers. The effects of substitution on the side chain, structure of the liquid‐–crystalline phase, and thermal stability of the polymers have also been discussed. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2396–2403, 2001