Effect of temperature on the conformation of dibenzotropone adsorbed on montmorillonites

The nature of the adsorption complex formed between dibenzotropone (DBT) and montmorillonite at elevated temperatures is strongly dependent on the interlayer cations. This was shown by electronic and IR spectra, by X-ray diffraction, and by study of the effects of gradual heating of the samples on these analyses. All samples exhibited significant red shifts of the electronic spectra of DBT into the visible range. These red shifts are attributed to two factors, both contributing to the enhancement of the tropylium planar character of DBT: hydrogen-bonding of acidic interlayer water to the carbonyl group, imparting positive charge to the tropone ring; and π interactions between the aromatic moiety and the oxygen planes. The position of the maximum was temperature-dependent for Cu-, Ni-, Al- and Fe-montmorillonites, for which heating (100°) under vacuum increased the red shift. The organic molecule assumes a planar conformation and is oriented parallel to the clay layers. IR spectra confirming this conformational orientation of DBT are discussed. The basal spacings of the DBT montmorillonite associations depend on the number of water and DBT sheets present in the interlayers. Layers with one or two sheets of DBT and with up to two sheets of water could be distinguished, leading to a maximum spacing of 20.4 Å.     

Effect of carbon-black treatment by radiation emulsion polymerization on temperature dependence of resistivity of carbon-black-filled polymer blends

High dispersibility and stability of carbon black particles in low-density-polyethylene (LDPE) matrix were obtained by radiation emulsion polymerization on carbon particles surface, and electrical resistivities of its simple were examined. First carbon particles treatment on radiation emulsion polymerization on surface were synthesized by the reaction with a polymer-emulsion systems containing reactive group in the molecular unit, carbon particles and emulsifier. Then, the carbon particles treatment on radiation emulsion polymerization on surface was dispersed into LDPE, and its composites were prepared for electrical measurements. The effect of radiation crosslinking of the composite on the Positive temperature coefficient (PTC) and negative temperature coefficient (NTC) phenomenon was investigated. The experimental results showed that PTC and NTC effects of the composites were obviously influenced by the irradiation dose. Various microstructure-exploring means were used to study the conductive composite, such as scanning electron microscopy (SEM), X-ray diffraction (XRD) and transmission electron microscopy (TEM).     

Interactions between surfactant-coated surfaces in hydrocarbon liquids containing functionalized polymer dispersant

The forces and viscosity between calcium benzene sulfonate surfactant-coated mica surfaces in various hydrocarbon liquids containing a polyamine-functionalized hydrocarbon polymer (M _W≈8000) have been measured using the surface forces apparatus technique. The polymer is found to adsorb to the substrate surfaces by displacing the surfactant layer, and to produce forces that are monotonically repulsive. The forces have a maximum range of 50–100 nm (>3R _H), indicating that tails play a particularly important role in the interaction of this relatively low molecular weight polymer. The forces become steeply repulsive below about 10 nm (∼0.6R _H), at which point a “hard-wall” repulsion comes in that can sustain pressures greater than 100 atm. Thin-film viscosity measurements indicate that the far-field positions of the slipping planes Δ_H depend on the shear rate, showing that significant shear thinning/thickening effects occur within the outermost tail regions of the adsorbed layers during shear. The position of the slipping plane, or hydrodynamic layer thickness Δ_H, varies from 0.6R _H to 2R _H away from each surface (mica and surfactant-coated mica surfaces). Beyond the hydrodynamic layer the far-field fluid viscosity is the same as that of the bulk polymer solution. At separations below D = 2Δ_H the viscosity increases as each polymer layer is compressed. The static forces exhibited various time- and history-dependent effects, which further indicate that a number of different relaxation/equilibration processes are operating simultaneously in this complex multicomponent system. The results reveal that the interactions of tails of functionally adsorbed polymers play a more important role than previously thought. This is especially true in this study where the adsorbed polymers are of low molecular weight and where the tails may represent the largest fraction of interacting segments. Received: 22 September 1998 Accepted: 11 January 1999     

Effect of particle agglomeration and interphase on the glass transition temperature of polymer nanocomposites

In this article, we utilize finite element modeling to investigate the effect of nanoparticle agglomeration on the glass transition temperature of polymer nanocomposites. The case of an attractive interaction between polymer and nanofiller is considered for which an interphase domain of gradient properties is developed. This model utilizes representative volume elements that are created and analyzed with varying degrees of nanoparticle clustering and length scale of interphase domain. The viscoelastic properties of the composites are studied using a statistical approach to account for variations due to the random nature of the microstructure. Results show that a monotonic increase in nanofiller clustering not only results in the loss of interphase volume but also obstructs the formation of a percolating interphase network in the nanocomposite. The combined impacts lead to a remarkable decrease of T_g enhancement of clustering nanofillers in comparison with a well‐dispersed configuration. Our simulation results provide qualitative support for experimental observations that clustering observed at high nanofiller concentrations negatively impacts the effects of the nanofiller on overall properties. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Effect of coexistent hydrocarbon phase on the volume behavior of adsorbed film and micelle of dodecyltrimethylammonium chloride

Interfacial tension () between aqueous dodecyltrimethylammonium chloride (DTAC) solution and benzene was measured as a function of pressure (p) and concentration. The/p was observed to change discontinuously at the critical micelle concentration; this indicates that the micelle formation of DTAC in the aqueous solution coexisting with benzene can be treated like the appearance of a macroscopic phase. It was shown by drawing the vs.A curves that hydrocarbon, such as benzene, cyclohexane, and hexane, make the adsorbed film of DTAC expand. The volume behavior of the micelle with benzene molecules solubilized was found to bear a strong resemblance to that of the adsorbed film at the water/benzene interface. The difference in the molar volume value of adsorbed DTAC among the coexistent hydrocarbon phases was attributed to the difference in the contribution of the hydrocarbon molecules to the interfacial excess volume; the number of the solubilized hydrocarbon molecules was evaluated to be one or two a micelle.     

STM studies on adsorbed liquid crystal on HOPG

Ｓｃａｎｎｉｎｇｔｕｎｎｅｌｉｎｇｍｉｃｒｏｓｃｏｐｅ(ＳＴＭ)ｈａｓｒｅｃｅｎｔｌｙｂｅｅｎａｐｐｌｉｅｄｔｏｔｈｅｓｔｕｄｙｏｆｔｈｅａｄｓｏｒｐｔｉｏｎｏｆｏｒｇａｎｉｃａｎｄｂｉｏｌｏｇｉｃａｌｍｏｌｅｃｕｌｅｓｉｎｖａｒｉｏｕｓｅｎｖｉｒｏｎｍｅｎｔｓ,ｉｎｃｌｕｄｉｎｇｌｉｑｕｉｄｃｒｙｓｔａｌ(ＬＣ),ｏｎｓｕｒｆａｃｅ.Ｉｎｐａｒｔｉｃｕｌａｒ,4＿ｎ＿ａｌｋｙｌ4′ｃｙａｎｏｂｉｐｈｅｎｙｌｓ(ｍＣＢ,ｗｈｅｒｅｍｉｓｔｈｅｎｕｍｂｅｒｏｆｃａｒｂｏｎｓｉｎｔｈｅａｌｋｙｌｇｒｏｕｐ)ｏｎ…     

Effect of temperature on gradient reequilibration in reversed-phase liquid chromatography

The effect of mobile phase modifier and temperature on gradient reequilibration is examined using three different stationary phases. The stationary phases studied are a traditional C18 phase, a polar endcapped C18 phase, and an alkyl phase with a polar embedded group. It was observed that both temperature and choice of mobile phase organic modifier had an effect on gradient reequilibration volume on both the traditional C18 stationary phase and the polar endcapped phase. On both these phases, at any given temperature, the reequilibration volume was generally smaller when methanol was used as the mobile phase modifier as compared to acetonitrile. As the temperature is increased from 10 to 50 degrees C, significant reductions in reequilibration volume were observed with both mobile phase modifiers. In contrast, neither temperature nor choice of modifier appeared to have much effect on reequilibration volume when the polar embedded group stationary phase was considered.     

Imaging of micropatterned self-assembled monolayers with adsorbed liquid crystals

We report a novel method of imaging micropatterned self-assembled monolayers (SAMs) using adsorbed films of thermotropic (smectic or nematic) mesophase which can then be studied by optical microscopy. Three alkylthiols, functionalized with CH3, OH and COOH groups, were used in various combinations to form patterned SAMs. Two alkylcyanobiphenyls (7CB and 9CB) were used as the liquid crystal imaging reagents. The images are formed by the contrast generated by the different alignments of adsorbed smectic or nematic films induced by different regions of the pattern. The spatial resolution is at least to 4 μm.     

Effect of temperature in reversed phase liquid chromatography

The high temperature liquid chromatography (HTLC) reveals interesting chromatographic properties but even now, it misses some theoretical aspects concerning the influence of high temperature on thermodynamic and kinetic aspects of chromatography: such a knowledge is very essential for method development. In this work, the effect of temperature on solute behavior has been studied using various stationary phases which are representative of the available thermally stable materials present on the market. The thermodynamic properties were evaluated by using different mobile phases: acetonitrile-water, methanol-water and pure water. The obtained results were discussed on the basis of both type of mobile phases and type of stationary phases. Type of mobile phase was found to play an important role on the retention of solutes. The kinetic aspect was studied at various temperatures ranging from ambient temperature to high temperature (typically from about 30 to 200 degrees C) by fitting the experimental data with the Knox equation and it was shown that the efficiency is improved significantly when the temperature is increased. In this paper, we also discussed the problem of temperature control for thermostating columns which may represent a significant source of peak broadening: by taking into account the three main parameters such as heat transfer, pressure drop and band broadening resulting from the preheating tube, suitable rules are set up for a judicious choice of the column internal diameter.     

Effect of pH on adsolubilization of single and binary organic solutes into a cationic hydrocarbon surfactant adsorbed layer on silica

The adsolubilization behaviors of 2-naphthol, biphenyl, and their binary solutes in the hexadecyltrimethyl ammonium bromide (HTAB) adsorbed layer formed on silica have been studied with solution pH. Two feed concentrations of HTAB are employed: 1.5 and 3.0 mmol dm(-3). At the feed concentration of 1.5 mmol dm(-3) HTAB, most of HTAB are adsorbed on the silica as a monolayer, while a bilayer formation occurs at the feed concentration of 3.0 mmol dm(-3). It is found that the adsolubilized amounts of respective single solutes increase with increasing solution pH except acidic region for biphenyl under a constant feed concentration of 2-naphthol (0.4 mmol dm(-3)) and biphenyl (0.047 mmol dm(-3)). The adsolubilization of binary solutes depends on the feed concentration of HTAB; at the low HTAB feed concentration, competitive adsolubilization between 2-naphthol and biphenyl occurs above pH 4.5, while at the high HTAB feed concentration the adsolubilization of biphenyl is enhanced by the incorporation of 2-naphthol over a whole pH region. These behaviors in the adsolubilization are discussed from the surfactant structure of HTAB adsorbed as well as the admicellar partitioning coefficients.     

The electrical conductivity of polymer blends filled with carbon-black

The electrical conductivity of natural rubber/polyethylene blends filled with carbon-black is much higher than those of the individual components at the same loading level. This effect cannot be explained by a higher affinity of carbon-black for one component of the blend.     

Studies on the behavior of liquid hydrocarbon systems

A method for estimating the effect of intermolecular interaction and component structure on oil system properties is suggested. The results of calculations via the models of oil system properties taking into account their non-additivity are presented.     

The effect of hydrocarbon chain length in normal aliphatic alcohols on their reaction with oxygen adsorbed on polycrystalline platinum electrode

The reaction of adsorbed oxygen (O_ads) with aliphatic alcohols n-C _n H_{2n + 1}OH with n = 2–5 is studied by the method of transients of open-circuit potential in combination with potentiodynamic pulses. It is shown that these alcohols react with O_ads by a mechanism the same as for CH₃OH. Kinetic parameters of these reactions are determined in ranges of high and medium surface coverages with O_ads. These data together with analogous results obtained earlier for CH₃OH were studied with the aim of elucidating how the length of the hydrocarbon chain affects the kinetics of interaction of alcohols with O_ads. The complex variations of the reaction rate with n (with a maximum) are explained by several factors among which the energy of the C–H bond at α-carbon atom and the degree hydration of alcohols should be singled out.     

Effect of temperature on the adsorption behavior of tryptophan in reversed-phase liquid chromatography

Single-component adsorption isotherm data of l-tryptophan on a C(18)-bonded silica column were acquired by frontal analysis (FA), with aqueous mobile phases containing 5% of acetonitrile at five different temperatures between 23 and 62 degrees C. The non-linear fitting of these data provided the bi-Moreau model for all temperatures as the best isotherm model. The inverse method (IM) was used to derive the parameters at these temperatures from the parameters of the 25 degrees C isotherm. The adsorption constants and the saturation capacities of the low and high-energy sites decreases by increasing the temperature, while the adsorbate-adsorbate parameters of both sites increase. An excellent agreement was found between the experimental and calculated overloaded band profiles at all the temperatures used. The breakthrough curves obtained and the overloaded band profiles obtained were found to have different shapes according to the range of concentration studied and the temperatures. At low concentration 0.05-0.5 g/L the breakthrough curves and the overloaded band profiles have a front shock and diffuse rear, which indicates langmuirian behavior, but at intermediate 1-2 g/L and high concentration 8 g/L they start to have diffuse fronts and shocks at the rear or more than one shock at the rear which indicates non-langmuirian behavior. At 23 degrees C the isotherm has another langmuirian part, which appears at high concentration. The behavior of the breakthrough curves is explained by the shape of the isotherm in which all of the isotherms have a langmuirian part (the isotherm is concave upward) and an antilangmuirian part (the isotherm is concave downward). The temperature affected the breakthrough curves by decreasing the time of the appearance of the fronts for all concentration ranges studied, and by decreasing the time difference between the highest concentration and lowest concentration of the fronts, especially the low concentration range at 0.5 g/L. The fronts of the breakthrough curves at high concentration seems to be the most affected by temperature.     

Low temperature structural fluorescence spectra of tetrahydroxyanthraquinone adsorbed on silica

Adsorption of TOAQ on the surface of porous (silica gel) and non-porous (aerosil) silica modification does not cause rupture of intramolecular hydrogen bonds (IMHB). The fine structure spectra of TOAQ fluorescence on silica gel contain a set of frequencies that are characteristic of weakly perturbed molecules. A number of new spectral effects appear due to the existence of pores and centres of a nonhydroxyl character. Hydroxyl groups of aerosil take part in formation of intermolecular hydrogen bonding with the TOAQ C=O group. The bond energy of the four OH-groups of the TOAQ molecule changes non-uniformly, and the symmetry of an equilibrium nuclear configuration of TOAQ decreases.     

Effect of valence of copper on adsorption of dimethyl sulfide from liquid hydrocarbon streams on activated bentonite

Samples of activated bentonite and activated bentonite modified with CuCl and CuCl₂, separately, were tested as dimethyl sulfide (DMS) adsorbents. The adsorption and desorption behaviours of DMS on the adsorbents were studied systematically. The adsorbents were characterised by nitrogen adsorption, XRD, and DMS-TPD tests. The addition of CuCl and CuCl₂ to the activated carbon significantly enhanced the adsorption capacity of DMS, despite a notable decrease in the specific surface area and total pore volume of the activated bentonite. It is presumed that copper cation species may act as an adsorption site for DMS. The adsorption capacity of Cu(II)-bentonite was better than that of Cu(I)-bentonite. The DMS-TPD patterns indicate that the stronger electrophilicity of Cu(II) compared to that of Cu(I) caused it to interact with the DMS molecules more strongly, thus contributing to a better adsorptive performance. The Cu(II)-bentonite calcined at 150°C had the best DMS removal performance with a high sulphur capacity of 70.56 mg S g^?1 adsorbent. The DMS removal performance became much lower with the increase in the calcination temperature, which appeared to be due to the decrease in the CuCl₂·2H₂O phase and the formation of the monoclinic Cu(OH)Cl phase.     

温度对松木屑气化液体产物组成的影响

利用傅里叶变换红外光谱(FT-IR)和气质联用(GC/MS)技术,研究了松木屑在400~900℃气化液体产物的主要组成成分和液体产物主要化学组成的来源与转化随气化温度变化的规律。结果表明,松木屑低温气化液体产物主要为酮、呋喃和愈创木酚等含氧化合物。随气化温度升高,液体产物的组成发生显著变化,400~ 500℃主要发生愈创木酚向酚类化合物的转变,500~600℃主要发生酮、呋喃向酚类化合物的转变,600~700℃主要发生酚类向茚和PAHs (多环芳烃)的转变,700~900℃主要发生酚类化合物向PAHs的转变,900℃液体产物的组成为大分子量的PAHs。