A novel structural form of MIL-53 observed for the scandium analogue and its response to temperature variation and CO2 adsorption

The scandium analogue of the flexible terephthalate MIL-53 yields a novel closed pore structure upon removal of guest molecules which has unusual thermal behaviour and stepwise opening during CO(2) adsorption. By contrast, the nitro-functionalised MIL-53(Sc) cannot fully close and the structure possesses permanent porosity for CO(2).     

Mg-Al-Fe-containing layered hydroxides

Magnesium-aluminum-iron layered hydroxides with hydrotalcite-like structure have been synthesized, and their chemical composition and crystal lattice parameters have been elucidated. Thermal decomposition of the iron-containing layered hydroxides has been studied by X-ray diffraction, thermogravimetry, and IR spectroscopy; the decomposition starts with loss of interlayer water, followed by dehydroxylation of metal hydroxide layers and decomposition of anions at higher temperature. Onset of the both decomposition stages has been shifted to lower temperature with increasing iron fraction in the sample. Magnesium-aluminum-iron hydroxides restore their structure after annealing and subsequent rehydration.     

Trace element determination in high-purity scandium by neutron activation analysis and pre-irradiation matrix separation

A pre-irradiation separation procedure has been developed for the determination of trace elements in high-purity scandium by neutron activation analysis. The sample is dissolved in high-purity concentrated hydrochloric acid and scandium is extracted with the same volume of a solution of 50 vol.% bis(2-ethyl hexyl)-orthophosphoric acid (HDEHP) in toluene. The scandium matrix is removed from the most important trace impurities and the residual amount of Sc is in the range of 0.001%. The separation is carried out in the vial to be used in irradiation to prevent sample contamination. Detection limits in the ppb range were achieved with a sample of 10 mg, a thermal neutron flux of 2 · 10¹³ n · cm^–2 · s^–1 and an irradiation time of 48 hours. Most of the elements sought in two samples of high-purity scandium were below the detection limits.     

Monte Carlo simulation study of reflection electron energy loss spectroscopy of an Fe/Si overlayer sample

Reflection electron energy loss spectroscopy (REELS) has been used to study the optical and electronic properties of semi-infinite solid samples, aided by a theoretical model of the interaction between electrons and a solid. However, REELS has not been used to its full capacity in studying nanomaterial samples because of the difficulty in modeling the electron interaction with a layered nanostructure. In this study, we present a numerical calculation result on the spatially varying inelastic mean free path for a sample comprising an Fe layer of varying thickness on an Si substrate. Furthermore, a Monte Carlo model for electron interaction with this Fe-Si layered structure sample is built based on this inelastic scattering cross section and used to reproduce the REELS spectra of Fe-Si layered structures. The simulated spectra of the sample with varying Fe layer thickness on top of a Si substrate were compared with the experimental spectra. This comparison clearly identifies that the Fe layer remaining on top of the experimental Si substrate after Ar⁺ beam sputtering is in the form of a homogeneous mixed layer, where the Fe/Si interface excitation is absent in the experimental spectra owing to pulverization of the Fe/Si interface during the Ar⁺ sputtering process.     

Formation and characterization of the oxygen-rich scandium oxide/dioxygen complexes ScOn (n = 4, 6, 8) in solid argon

The reactions of scandium atoms and O(2) have been reinvestigated using matrix isolation infrared spectroscopy and density functional theory calculations. A series of new oxygen-rich scandium oxide/dioxygen complexes were prepared and characterized. The ground state scandium atoms react with dioxygen to form OSc(eta(2)-O(3)), a side-on bonded scandium monoxide-ozonide complex. The OSc(eta(2)-O(3)) complex rearranges to a more stable Sc(eta(2)-O(2))(2) isomer under visible light irradiation, which is characterized to be a side-on bonded superoxo scandium peroxide complex. The homoleptic trisuperoxo scandium complex, Sc(eta(2)-O(2))(3), and the superoxo scandium bisozonide complex, (eta(2)-O(2))Sc(eta(2)-O(3))(2), are also formed upon sample annealing. The Sc(eta(2)-O(2))(3) complex is determined to have a D(3h) symmetry with three equivalent side-on bonded superoxo ligands around the scandium atom. The (eta(2)-O(2))Sc(eta(2)-O(3))(2) complex has a C(2) symmetry with two equivalent side-on bonded O3 ligands and one side-on bonded superoxo ligand.     

Experimental and theoretical studies of 45Sc NMR interactions in solids

Solid-state 45Sc NMR spectroscopy, ab initio calculations, and X-ray crystallography are applied to examine the relationships between 45Sc NMR interactions and molecular structure and symmetry. Solid-state 45Sc (I = 7/2) magic-angle spinning (MAS) and static NMR spectra of powdered samples of Sc(acac)3, Sc(TMHD)3, Sc(NO3)3.5H2O, Sc(OAc)3, ScCl3.6H2O, ScCl3.3THF, and ScCp3 have been acquired. These systems provide a variety of scandium coordination environments yielding an array of distinct 45Sc chemical shielding (CS) and electric field gradient (EFG) tensor parameters. Acquisition of spectra at two distinct magnetic fields allows for the first observations of scandium chemical shielding anisotropy (CSA). 45Sc quadrupolar coupling constants (CQ) range from 3.9 to 13.1 MHz and correlate directly with the symmetry of the scandium coordination environment. Single-crystal X-ray structures were determined for Sc(TMHD)3, ScCl3.6H2O, and Sc(NO3)3.5H2O to establish the hitherto unknown scandium coordination environments. A comprehensive series of ab initio calculations of EFG and CS tensor parameters are in excellent agreement with the observed parameters. Theoretically determined orientations of the NMR interaction tensors allow for correlations between NMR tensor characteristics and scandium environments. Solid-state 45Sc, 13C, and 19F NMR experiments are also applied to characterize the structures of the microcrystalline Lewis acid catalyst Sc(OTf)3 (for which the crystal structure is unknown) and a noncrystalline, microencapsulated, polystyrene-supported form of the compound.     

Structural and texture evolution with temperature of layered double hydroxides intercalated with paramolybdate anions

Paramolybdate-LDHs with MgAl or ZnAl cations within the layers have been prepared by the ion-exchange method from hydrotalcites with different interlayer anions (OH-, NO3(-), and terephthalate). The samples and the oxides obtained after their calcination were characterized by element chemical analysis, PXRD, FT-Raman spectroscopy, thermal analysis (TG/DTA), N2 adsorption at -196 degrees C, and SEM. The results show that layered solids with hydrotalcite-type structure were obtained in which the interlayer space is occupied by heptamolybdate with a small amount of MoO4(2-) units formed through hydrolysis of the polyanion; both oxomolybdenum species undergo a progressive distortion of the octahedral units from 50 degrees C but are roughly stable up to 250 degrees C as a consequence of the interaction between the polyanion and the brucite-like layers. This distortion is responsible for the observed decrease in the height of the gallery for samples heated in the temperature range, 50-250 degrees C, with respect to the original samples. Rehydration of the calcined solids allows recovering of their original structures and the initial values for the gallery heights. Calcination between 300 and 400 degrees C gives rise to a collapse of the layered structure, and amorphous phases are formed, in which molybdenum is both octahedrally and tetrahedrally coordinated. Crystalline magnesium and zinc molybdates (MgMoO4 and ZnMoO4) are formed at 450 and 600 degrees C, respectively. All solids have some microporosity, which decreases with increasing the calcination temperature.     

Extraction-Spectrophotometric Determination of Fluoride Using N-Phenylbenzohydroxamic Acid

Abstract

Fluoride gives a very stable complex with scandium and, hence, by determining the unreacted scandium, the fluoride content can be calculated. Excess scandium is reacted with an ethanolic solution of N-benzoylphenylhydroxylamine (BPHA) at pH 6.0, and the scandium-BPHA complex is extracted into isoamyl alcohol. Scandium is determined spectrophotometrically after adding xylenol orange. Beer's law for fluoride is obeyed in the range of 0.05 –1.5 ppm; the molar absorptivity is 1.94×10⁴ 1 mol^?1 at 565 nm. The procedure is applicable for the determination of fluoride in various types of samples.     

一种新型的纳米功能材料:磁性纳米镁铝水滑石

本文将磁性基质与镁铝水滑石进行组装首次合成出一种新型的纳米磁性功能材料—磁性纳米镁铝水滑石。这种新型纳米功能材料的XRD及TA结果表明,镁铝水滑石赋予磁性后并没有改变其层状结构的典型特征。样品的TEM图表明,磁性基质的加入后样品的颗粒粒径并没有明显增大,且保持在20～50nm之间。对磁性镁铝水滑石磁性能的考察结果表明,样品的比饱和磁化强度随磁性基质含量的增加而线性增加。     

The hydration of the scandium(III) ion in aqueous solution and crystalline hydrates studied by XAFS spectroscopy, large-angle X-ray scattering and crystallography

The structures of the hydrated scandium(III) ion and of the hydrated dimeric hydrolysis complex, [Sc2(mu-OH)2]4+, in acidic aqueous solutions have been characterized by X-ray absorption fine structure (XAFS) and large-angle X-ray scattering (LAXS) methods. Comparisons with crystalline reference compounds containing hydrated scandium(III) ions in well characterized six-, seven- and eight-coordinated polyhedra have been used to evaluate the coordination numbers and configurations in aqueous solution. In strongly acidic aqueous solution the structure of the hydrated scandium(III) ion is found to be similar to that of the eight-coordinated scandium(III) ion with distorted bicapped trigonal prismatic coordinating geometry in the crystalline [Sc(H2O)(8.0)](CF3SO3)3 compound. The EXAFS data reveal for the solution, as for the solid, a mean Sc-O bond distance of 2.17(1) Angstrom to six strongly bound prism water molecules, 2.32(4) Angstrom to one capping position, with possibly another capping position at about 2.5 Angstrom. The LAXS study supports this structural model and shows furthermore a second hydration sphere with approximately 12 water molecules at a mean Sc...O(II) distance of 4.27(3) Angstrom. In less acidic concentrated scandium(III) aqueous solutions, the dimeric hydrolysis product, [Sc2(mu-OH)2(H2O)10]4+, is the predominating species with seven-coordinated scandium(III) ions in a double hydroxo bridge and five terminal water molecules at a mean Sc-O bond distance of 2.145 Angstrom. Hexahydrated scandium(III) ions are found in the crystal structure of the double salt [Sc(H2O)6][Sc(CH3SO3)6], which crystallizes in the trigonal space group R3[combining macron] with Z = 6 and the unit cell dimensions a = 14.019(2) and c = 25.3805(5) Angstrom. The Sc-O distances in the two crystallographically unique, but nearly identical, [Sc(H2O)6]3+ entities (both with 3[combining macron] imposed crystallographic symmetry) are 2.085(6) and 2.086(5) Angstrom, while the mean Sc-O distance in the near octahedral [Sc(OSO2CH3)6]3- entities (with three-fold symmetry) is 2.078 Angstrom.     

Resonance raman spectra of meso-tetramethylporphine,meso-tetraethylporphine and their nickel complexes measured by using the sers technique

Surface-enhanced resonance Raman scattering spectroscopy was applied to measure the vibrational spectra of meso-tetramethylporphine (TMP), meso-tetraethylporphine (TEP), and their nickel complexes in layered structures having CaF₂/sample/Ag (structure I) and CaF₂/Ag/sample (structure II) configurations. The surface spectra clearly prove that, when the samples come into contact with Ag atoms (structure I) or a vacuum-deposited Ag film (structure II), they undergo chemical processes such as metal-incorporation and metal-exchange reactions, and a structural change.     

Determination of cobalt and nickel by graphite-furnace atomic absorption spectrometry after coprecipitation with scandium hydroxide.

Trace amounts of cobalt and nickel in a water sample were quantitatively coprecipitated with scandium hydroxide at pH 8.0-10.5. Because the coprecipitant could be easily dissolved with 1 mol dm(-3) nitric acid, and the presence of up to 10 mg cm(-1) of scandium did not interfere with the graphite-furnace atomic absorption spectrometric determination of cobalt and nickel, the volume of the final solution prepared for the determination could be minimized down to 0.5 cm3. The concentration factor was 400-fold and the detection limits (signal to noise = 2) were 5.0 pg cm(-3) of cobalt and 10.0 pg cm(-3) of nickel in 200 cm3 of the initial sample solution. The 27 diverse ions investigated did not interfere with the determination in at least a 500-fold mass ratio to cobalt or nickel. The proposed method was successfully applied to the determination of trace amounts of cobalt and nickel in river-water samples.     

Supramolecular graphyne: a C(sp)-H...N hydrogen-bonded unique network structure of 2,4,6-triethynyl-1,3,5-triazine

The crystallization of 2,4,6-triethynyl-1,3,5-triazine (2) leads to a pi-stacked layered structure of a C(sp)-H...N hydrogen-bonded unique hexagonal network structure, which may be regarded as a supramolecular analogue of a hitherto unknown graphyne network: in-plane intermolecular interactions are short and linear H...N contacts (2.31 and 2.34 A) and the interlayer separation is 3.23 A.     

Determination of scandium and lanthanum in silicate rocks and coal with a simplified separation procedure and atomic absorption spectrometry

Simplified procedures for the quantitative separation and enrichment of scandium and lanthanum in igneous rocks are described. Co-precipitation with calcium oxalate is followed by co-precipitation with hydrated iron(III) oxide. Electrothermal and flame atomic absorption spectrometry are applied. The procedures are verified with synthetic sample solutions and the eighteen international reference samples of rocks and coal compare favourably with previously reported data and with data obtained by emission spectrography.     

The Structure of the Aluminum Fumarate Metal–Organic Framework A520

The synthesis of the commercially available aluminum fumarate sample A520 has been optimized and its structure analyzed through a combination of powder diffraction, solid‐state NMR spectroscopy, molecular simulation, IR spectroscopy, and thermal analysis. A520 is an analogue of the MIL‐53(Al)‐BDC solid, but with a more rigid behavior. The differences between the commercial and the optimized samples in terms of defects have been investigated by in situ IR spectroscopy and correlated to their catalytic activity for ethanol dehydration.     

Studies on the scandium distribution in organs of fattened chicken by neutron activation analysis

Tissues samples of chicken /blood, liver, spleen, fat, pancreas, kidney, lung, breast muscle, brain, femur, faeces, egg yolk, white of egg/, were analyzed for scandium concentration. ScCl₃ was applied intravenously /1 mg kg^–1 body weight/. High scandium concentrations were found in the liver /34. 35 ppm/, spleen /15.46 ppm/, and lung /15.52 ppm/ three days after application. This experiment shows that accumulation of scandium occurs in the yolk of egg but not in the white of the egg.     

Determination of trace quantities of scandium in silicate rocks by a combined ion exchange-spectrophotometric method

A spectrophotometric determination of scandium in silicate rocks has been developed with arsenazo as the color reagent. After the decomposition of samples with a hydrofluoric-perchloric acid mixture, traces of scandium are separated from interferences by cation- and anion-exchange in acid sulfate media and anion exchange in hydrochloric acid solution. The successive 3 steps, with an intermediate concentration step, yield scandium in a sufficiently pure state for spectrophotometric determination.     

A study of the reactivity of elemental Cr/Se/Te thin multilayers using X-ray reflectometry, in situ X-ray diffraction and X-ray absorption spectroscopy

The reactivity of [Cr/Se/Te] multilayers under annealing was investigated using X-ray reflectometry, in situ X-ray diffraction, X-ray absorption fine structure (XAFS) measurements and transmission electron microscopy. For all samples, interdiffusion was complete at temperatures between 100 and 300 °C, depending on the repeating tri-layer thickness. A crystalline phase nucleated approximately 20 °C above the temperature where interdiffusion was finished. The first crystalline phase in a binary Cr/Te sample was layered CrTe₃ nucleating at 230 °C. In ternary samples (Se:Te=0.6-1.2), the low-temperature nucleation of such a layered CrQ₃ (Q=Se, Te) phase is suppressed and instead the phase Cr₂Q₃ nucleates first. Interestingly, this phase decomposes around 500 °C into layered CrQ₃. In contrast, binary Cr/Se samples form stable amorphous alloys after interdiffusion and Cr₃Se₄ nucleates around 500 °C as the only crystalline phase. Evaluation of the XAFS data of annealed samples yield Se-Cr distances of 2.568(1) and 2.552(1) Å for Cr₂Q₃ and CrQ₃, respectively. In the latter sample, higher coordination shells around Se are seen accounting for the Se-Te contacts in the structure.     

The functional layered organosilica materials prepared with anion surfactant templates

A novel strategy for the synthesis of layered organosilica is demonstrated. The ionic interaction between the anionic group of a surfactant (sodium dodecyl sulfate) and the cationic organic group of an organosilane (3-aminopropyltrimethoxysilane, ATMS) under acidic conditions was utilized to create a layered organosilica at room temperature. The inorganic part of the organosilica layer was an Si-O hexagonal sheet, and organofunctional groups were alternately arranged on both sides of the sheet. The layered structure of the ATMS organosilica was retained after the removal of the surfactant with chloride anion. The properties of the layered ATMS organosilica were investigated. The layered ATMS-Cl organosilica is stable and possesses a definite layer structure in water or ethanol. Various kinds of anions can be intercalated in the interlayer space of the layered ATMS organosilicas and the layer was expanded dependent on the intercalated anions. The structure of the layered ATMS organosilica was well retained during the intercalation processes.     

ICP-AES手动扫描光电测定微量钪

用ICP -ABS手动扫描光电测定硫酸钛白母液中微量钪 ,考察了基体及硫酸的存在对钪发射强度的影响 ,并采用标准加入法扣除样品基体的影响。本法无需经过分离、富集等预处理 ,方法简便、快速。