Fabrication and properties of MgF<Subscript>2</Subscript> composite film modified with carbon nanotubes

Carbon nanotubes (CNTs) were used to modify magnesium fluoride (MgF₂) film via the spin coating technique. Nanoparticles of MgF₂ were in situ synthesized on surfaces of CNTs resulted in the composites (MgF₂–CNTs) by means of sol–gel technique. The sizes of the MgF₂ nanoparticles in situ synthesized on CNTs surfaces could be modulated by processing the MgF₂ sol–gel in different ways. The MgF₂–CNTs as prepared was mixed with MgF₂ sol to fabricate composite films (MgF₂–CNTs/MgF₂). Instead of adding directly CNTs, adding MgF₂–CNTs, into MgF₂ sol could effectively improve the dispersion of CNTs, avoid emergence of carbon clusters in the compsite film, decrease surface roughness of the film, and enhance the interaction between the CNTs and MgF₂ matrix. In the paper, the MgF₂ nanoparticles were in situ synthesized on the surfaces of multi-walled carbon nanotubes (MWCNTs) and single-walled carbon nanotubes (SWCNTs) respectively to prepare MgF₂–SWCNTs/MgF₂ and MgF₂–MWCNTs/MgF₂ composite films. Experimental results showed that the transparency of the MgF₂–SWCNTs/MgF₂ composite film was higher than that of the MgF₂–MWCNTs/MgF₂ film in the range of ultraviolet, visible and near-infrared wavelengths. The results showed SWCNTS could be an ideal reinforcement of MgF₂ films to get good toughness, and retain its optical transmittance at the same time.     

A determination method of pristine multiwall carbon nanotubes in rat lungs after intratracheal instillation exposure by combustive oxidation-nondispersive infrared analysis

This paper describes a method for determination of multiwall carbon nanotubes (MWCNTs) in rat lungs after intratracheal instillation exposure. The MWCNTs were quantitatively decomposed to CO₂ by combustive oxidation and were then determined by non-dispersive infrared analysis. Samples were pretreated by acid digestion, muffle ashing and in situ preheating to remove interferences due to coexisting biological carbon from the lung tissue sample, while preserving the MWCNTs as in its their original form. The preservation was confirmed by transmission electron microscopic observation of the pretreated samples of exposed lung tissues and by the fact that the recoveries of MWCNTs spiked to the lung tissues were close to 100%. The detection limit for MWCNTs obtained by the proposed method was 0.30 μg and the repeatability as expressed by the relative standard deviation was 5.6% (n = 4). The method was sufficiently sensitive and precise to apply to real samples of rat lung to investigate the in vivo persistence of intratracheally instilled MWCNTs. To our knowledge, this is the first report of this type of sample pretreatment and direct determination of pristine MWCNTs without modification or tagging. Conventional indirect methods use tagging with other compounds or metal impurities in the CNTs for detection, and the detachment of these tags can increase uncertainties in the determination of the CNTs. The tags can also change how the CNTs persist in vivo, which can lead to an incorrect understanding of the persistence of pristine CNTs in vivo.     

The study of carbon nanotubes as conductive additives of cathode in lithium ion batteries

Carbon nanotubes (CNTs), including multi-walled CNTs (MWCNTs) and single-walled CNTs (SWCNTs), are employed as conductive additives in lithium ion batteries. The effects of MWCNTs’ carbon precursors, diameter, and weight fraction on the electrochemical behavior of MWCNTs/LiCoO₂ composite cathode are investigated. Meanwhile, a comparison is made between SWCNTs /LiCoO₂ and MWCNTs/LiCoO₂. Among the three kinds of carbon precursors: CH₄, natural gas, and C₂H₂, MWCNTs prepared from CH₄ are very fit for acting as conductive additives due to their better crystallinity and lower electrical resistance. MWCNTs with smaller diameter favor improving the electrochemical behavior of MWCNTs/LiCoO₂ composite cathode at higher charge/discharge rate owing to their advantage in primary particle number in unit mass. To make full use of LiCoO₂ at higher rate, it is necessary to add at least 5 wt.% of MWCNTs with a diameter 10~30 nm. However, SWCNTs are not expected to be added into LiCoO₂ composite cathode since they tend to form bundles.     

碳纳米管/SnO2复合电极的制备及其电催化性能研究

采用液相沉积法制备碳纳米管(CNTs)/SnO₂复合材料, 并制备成电极, 分别与石墨/SnO₂及活性炭/SnO₂复合电极比较, 考察电催化降解有机废水的性能. 由于CNTs高的比表面积及优良的导电性能, 结合SnO₂良好的催化活性, CNTs/SnO₂复合电极电催化降解有机废水性能优越. 研究发现, CNTs的预处理情况、SnO₂负载量以及煅烧温度对复合电极的电催化性能有重要影响. 当功能化CNTs负载40% SnO₂, 煅烧温度600 ℃时, 所得CNTs/SnO₂复合电极电催化降解有机废水的能力是纯CNTs电极的2倍. 最后, 初步探讨了CNTs/SnO₂复合电极电催化降解有机废水的机理.     

Multi-walled carbon nanotubes (MWCNTs)-bridged architecture of ternary Bi2O3/MWCNTs/Cu microstructure composite with high catalytic performance via two-step self-assembly

Binary and ternary microstructure composites based on CNTs have potential applications in many technological fields. In our works, we realized MWCNTs-bridged architecture of ternary Bi₂O₃/MWCNTs/Cu microstructure composite by two-step self-assembly. In order to verify its workability, we investigated catalytic performances of a series of additives for ammonium perchlorate (AP) thermal decomposition. The results showed that catalytic performance of Bi₂O₃/MWCNTs/Cu composite was better than those of the other additives, and the peak temperature for high-temperature AP decomposition reduced 151.6 °C; while no low-temperature AP decomposition was observed. MWCNTs have two crucial roles in catalytic enhancement on AP thermal decomposition: firstly, being to act as a supporter which can effectively disperse copper and Bi₂O₃ particles; secondly, being to act as a bridge, excited electrons from semiconductor can conduct and store on the surfaces of MWCNTs, which is beneficial for AP thermal decomposition. Therefore, MWCNTs-bridged architecture can synergistically enhance catalytic effect of copper and Bi₂O₃.     

Surfactants for CNTs dispersion in zirconia-based ceramic matrix by sol–gel method

Zirconium oxide is a ceramic material widely studied due to its mechanical and electrical properties that can be improved with the use of carbon nanotubes (CNTs) as reinforcement. The synthesis of CNT/zirconia composites by sol–gel method is still very scarce, due to the hydrophobic nature of the CNTs, being their dispersion in aqueous medium an intrinsic difficulty to the synthesis. In this work, we present a sol–gel synthesis for MWCNTs/zirconia composites, where two kinds of surfactants, sodium and ammonium stearates dissolved in water (1 g/100 mL), were used as dispersant agents for multiwall carbon nanotubes (MWCNTs). They are cheap and easy to prepare, and were very effective in dispersing the MWCNTs. Different quantities of MWCNTs (up to 5 wt%) were added in the solution of stearate/water and this solution with the highly dispersed MWCNTs was added to the zirconia sol–gel, producing composites of MWCNTs/zirconia with different concentrations of MWCNTs. All the powders were heat treated at 300 and 500 °C and the powder characterization was performed by transmission electron microscopy (TEM), X-ray diffraction (XRD), thermogravimetric analysis (TGA) and infrared spectroscopy (FTIR). The composite MWCNTs/zirconia remained amorphous at 300 °C and presented a tetragonal phase at 500 °C with an average grain size of about 20 ± 3 nm, determined by the Scherrer equation from the XRD patterns. For these crystalline samples, TEM images suggest a more effective interaction between MWCNTs with ZrO₂ matrix, where it can be observed that the carbon nanotubes are fully coated by the matrix.     

Fabrication,adsorption and photocatalytic properties of ZnTi0.6Fe1.4O4/Carbon nanotubes composites

ZnTi_xFe_(2–x)O_4 and ZnTi_(0.6)Fe_(1.4)O_4/Carbon nanotubes(ZT_(0.6)F_(1.4)/CNTs) composites were prepared by chemical co-precipitation method. The composition, microstructure, magnetic property, adsorption and photocatalytic activity of the prepared samples were characterized by means of modern analytical techniques. The results indicated that ZT_(0.6)F_(1.4)/CNTs composites not only held the original special structure and excellent adsorption properties of CNTs, but also had suitable magnetic property and excellent photocatalytic activity. The removal rate of the samples on Rhodamine B(RhB) depended on the adsorption of CNTs and the photocatalytic degradation of ZT_(0.6)F_(1.4) in the composites. The maximum adsorption amount(q_m) of ZT_(0.6)F_(1.4)/CNTs with the mass ratios of ZT_(0.6)F_(1.4) to CNTs(mZ/C)=1 was up to 17.153 mg g~(–1) for RhB, its adsorption behavior was in accord with Langmuir model, and its photocatalytic degradation activity on RhB had a positive correlation with the content of ZT_(0.6)F_(1.4) in the sample. The experimental results indicate that the total removal rate of composite with mZ/C=1 on RhB was more than 95% and the composite had good decontamination capability on industrial dye wastewater. In addition, the samples can be recovered conveniently, activated easily and had good performance for recycling.     

Preparation and Characterization of In-Situ Polymerized Nanocomposites Based on Polyaniline in Presence of MWCNTs

Summary: Polyaniline (PANI) composites were prepared with both unmodified and amine modified MWCNTs with and without BaTiO₃ through in-situ oxidative polymerization. Uniform coating of PANI on the MWCNTs and BaTiO₃ surfaces was found which was evident from the Field Emission Scanning Electron Microscopic (FESEM) and High Resolution Transmission Electron Microscopic (HRTEM) images. The structure of pure and amine modified MWCNTs was identified by Fourier Transform Infrared Spectroscopy (FTIR). The thermal stability of the amine modified composite with BaTiO₃ is higher than that of the unmodified composite because of the better affinity between modified MWCNTs and polymer matrix and due to the higher stability of barium titanate itself. The capacitance of amine modified MWCNTs and BaTiO₃ composites was less than that of the pure MWCNTs composites but the thermal stability increased in amine modified MWCNTs and BaTiO₃ composites with respect to the pure MWCNTs composites. The maximum capacitance and energy density values were found in MWCNT/PANI composites which were equal to 523.20 F/g and 142.83 Wh/kg respectively at a scan rate of 10mv/s. Maximum power density was found to be 5147.70 W/kg in the same composite at a scan rate of 200 mv/s.     

非共价修饰碳纳米管/二氧化钛复合材料的合成及性能

采用溶胶-凝胶法在聚乙烯吡咯烷酮(PVP)非共价修饰的碳纳米管表面均匀沉积二氧化钛粒子制得纳米复合材料。用TEM、XRD、FTIR、N2吸脱附等对复合材料进行了表征。结果表明:纳米二氧化钛纳米粒子均匀沉积在被修饰碳纳米管表面,且二氧化钛为纯锐钛矿晶体结构,没有金红石和板钛矿相。非共价修饰碳纳米管/二氧化钛复合材料具有良好的介孔结构,其孔径分布主要集中在6～10 nm,且比表面积与纯的二氧化钛相比明显增大,在紫外光照射下降解亚甲基蓝,相比纯的二氧化钛和碳纳米管/二氧化钛,具有较高的催化活性。     

Percolation behaviour of ultrahigh molecular weight polyethylene/multi-walled carbon nanotubes composites

The electrical conductivity of polymer/multi-walled carbon nanotubes (MWCNTs) composites in a powder and in a hot-pressed compacted state, prepared by mechanical mixing, was studied. The semicrystalline ultrahigh molecular weight polyethylene (UHMWPE) was used as a polymer matrix. The data clearly evidence the presence of a percolation threshold φ_c at a very small volume fraction of the MWCNTs φ in a polymer matrix, φ_c ≈ 0.0004-0.0007. The ultralow percolation threshold in UHMWPE/MWCNTs thermoplastic composites was explained by high aspect ratio of the nanotubes and their segregated distribution inside the polymer matrix. The method of composite preparation effects the values of percolation threshold concentration φ_c and critical exponent t. A noticeable positive temperature coefficient of resistivity (PTC effect) was observed in the region of temperatures higher than melting point. It was explained by influence of thermal expansion of the polymer matrix and independence from the melting process that is a result of specific structure of conductive phase.     

Decoration of MWCNTs with CoFe2O4 Nanoparticles for Methylene Blue Dye Adsorption

In the present work, a simple and viable method for producing multi-walled carbon nanotubes (MWCNTs) decorated with CoFe₂O₄ nanoparticles is presented. Chemical composition and crystal structure of the CoFe₂O₄/MWCNT composite was confirmed by X-ray diffraction measurements, while transmission electron microscopy was used to characterize the morphology and the distribution of nanocrystals in the composite. The obtained particles with relatively small diameter (about 14.9?nm) were found to be dispersed on the carbon nanotubes. The adsorption of methylene blue dye on CoFe₂O₄/MWCNT composites has been investigated. CoFe₂O₄/MWCNT composites show high adsorption capacity for methylene blue dye. Both Langmuir and Freundlich models describe the adsorption isotherms very well and the adsorption thermodynamic parameters (?G ⁰, ?H ⁰ and ?S ⁰) were calculated. The adsorption of methylene blue is generally spontaneous and thermodynamically favorable. The adsorption of methylene blue involves an endothermic process.     

Saqima-like Co<Subscript>3</Subscript>O<Subscript>4</Subscript>/CNTs secondary microstructures with ultrahigh initial Coulombic efficiency as an anode for lithium ion batteries

In this work, Co₃O₄/CNTs composite with Saqima-like secondary microstructure has been synthesized by heat treatment of CoC₂O₄/CNTs precursors being obtained through ultrasonication-assisted precipitation method. Through SEM, in the composites, the microstructures are composed of tightly connected nanoparticles (30–50 nm), and abundant spaces exist among nanoparticles, which can relieve the strain produced by volume effect to ensure the stability of integral structure during cycles; CNTs are dispersed in microstructures and bridge between microstructures, which can form a long-range conductive network in the composite. The electrochemical test indicates that the composite shows ultrahigh initial coulombic efficiency (ICE) of 85%, as well as excellent rate performance and cyclic stability. The high ICE is mainly ascribed to the formation of a stable solid electrolyte interphase (SEI) film only on the outer surface of microstructures. This work offers an available and general way to improve the ICE of transitional metal oxide as an anode material for LIB.     

Synthesis and properties of iron oxide coated carbon nanotubes hybrid materials and their use in epoxy coatings

Multi‐walled carbon nanotubes (MWCNTs) were acidified with nitration mixture, and the Fe₂O₃‐MWCNTs (iron oxide coated multi‐walled carbon nanotubes) hybrid material via sol‐gel method then verified the results through scanning electron microscope, X‐ray diffraction, and thermal gravimetric analysis. We modified the hybrid material with silane coupling agent (KH560), Fe₂O₃‐MWCNTs/epoxy, MWCNTs/epoxy composites coating, and the pure epoxy coatings were respectively prepared. The properties of the composite coatings were tested through the electrochemical workstation (electrochemical impedance spectroscopy), shock experiments, and thermal gravimetric analysis. Finally, we used scanning electron microscope to observe the surface conditions of the coatings. The results show that Fe₂O₃‐MWCNTs have good dispersion in the epoxy resin, and the Fe₂O₃‐MWCNTs/epoxy composite coatings have enhanced mechanical properties and corrosion resistance. Copyright © 2015 John Wiley & Sons, Ltd.     

Multi-stage Ordered Mesoporous Carbon-graphene Aerogel-Ni3S2/Co4S3 for Supercapacitor Electrode

Transition metal sulfides have emerged as promising materials in supercapacitor. In this work, we firstly developed an interface-induced superassembly approach to fabricate NiS_x and CoS_x nanoparticles, which based on ordered mesoporous carbon-graphene aerogel composites for supercapacitor electrodes. The obtained multi-component superassembled nanoparticles-carbon matrix composites have controllable 3D porous structure of multi-stage composite. The two-dimensional graphene interlaced to form a 3D framework with large sponge-like pores, and then the graphene surface was loaded with mesoporous carbon with mesoporous pore size and vertical orientation. The composites display high specific capacitance of 958.1 F g⁻¹ at 0.1 A g⁻¹. The capacitance retains about 97.3 % after 3000 charging-discharging cycles at 2 A g⁻¹. These results indicate that the obtained OMC−GA−Ni₃S₂/Co₄S₃ is a promising material for electrochemical capacitors, which providing new technical methods and ideas for the research of new energy and analytical sensor materials in the fields of energy storage, photocatalysis, point-of-care testing devices and other fields.     

Investigation on properties of V<Subscript>2</Subscript>O<Subscript>5</Subscript>–MWCNTs composites as cathode materials

An effective method to prepare the composites of multi-wall carbon nanotubes (MWCNTs) and vanadium pentoxide (V₂O₅) was presented. Vanadyl-triisopropoxide (VO(OC₃H₇)₃) was used as the starting material, MWCNTs pretreated with acids by a two-step process was used as the conductive ingredient. V₂O₅–MWCNTs composites were synthesized via a sol–gel method with solvent exchange and an ambient pressure drying technique. The samples were characterized by SEM, TEM, XRD, BET, Raman spectra and electrical resistivity measurement respectively. The experimental results indicate that the V₂O₅–MWCNTs nanocomposite has a fiber-like and tri-dimensional network structure. Its surface area is up to 189.7 m²/g when the MWCNTs’ content is 15 wt%. And MWCNTs are dispersed homogeneously in the composites. The electrical resistivity of the composites decreases from 1,239 to 765 Ω·cm when the MWCNTs’ content increases from 0 to 10 wt%. Thus MWCNTs can improve properties of V₂O₅ aerogels as the cathode material in lithium batteries.     

Controllable preparation and properties of composite materials based on ceria nanoparticles and carbon nanotubes

We report a method to prepare composites based on carbon nanotubes (CNTs) and CeO₂ nanoparticles (NPs). The CeO₂ NPs were attached to CNTs by hydrothermal treatment of Ce(OH)₄/CNT mixture in NaOH solution at 180 °C. It was found that larger CeO₂ NPs were formed in the presence of CNTs. Grain size of CeO₂ NPs in the composites can be reduced when NaNO₃ was added in the hydrothermal process. Electrochemical characterizations have shown that the composites possess a specific capacity between those of CNTs and CNTs mechanically mixed with CeO₂. These CeO₂/CNT composites could serve as promising anode materials for Li-ion batteries.     

Electrochemical properties of LiFePO4-multiwalled carbon nanotubes composite cathode materials for lithium polymer battery

LiFePO₄-multiwalled carbon nanotubes (MWCNTs) composites were prepared by a hydrothermal method followed by ball-milling and heat treating. Cyclic voltammetry, ac impedance and galvanostatic charge/discharge testing results indicate that LiFePO₄-MWCNTs composite exhibits higher discharge capacity and rate capability than pure LiFePO₄ at high-rate at room temperature. It is demonstrated that the added MWCNTs not only increase the electronic conductivity and lithium-ion diffusion coefficient but also decrease crystallite size and charge transfer resistance of LiFePO₄-MWCNTs composite.     

Comparison of the photonic effects of Mn-CNT/TiO<Subscript>2</Subscript> composites modified by different oxidants

Manganese-carbon nanotubes (CNTs) on titania (TiO₂) composites modified by different oxidants (KMnO₄, (NH₄)₂S₂O₈ and m-chlorperbenzoic acid (MCPBA)) were prepared with a sol-gel method. These composites were comprehensively characterized by the Brunauer-Emett-Teller (BET) method, scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy EDX, Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), transmission electron microscopy (TEM) and UV-vis absorption spectroscopy. The photoactivity of these materials prepared under visible light irradiation was tested using methylene blue in aqueous solution. The result shown that among the three oxidants, the MCPBA was the best one for the surface functionalization of CNTs and the manganese treated CNT/TiO₂ composite can enhance the photocatalytic activity. The proposed mechanism of the photodegradation of methylene blue on Mn-CNT/TiO₂ composites was present.     

Supramolecular Macrostructures of UPy‐Functionalized Carbon Nanotubes

Carbon nanotubes (CNTs) are considered excellent materials for the construction of flexible displays due to their nanoscale dimensions and unique physical and chemical properties. By using the recognition properties of 2‐ureido‐4[1H]pyrimidinone (UPy), a versatile and simple methodology was demonstrated for the construction of macroscopic structures based on UPy‐CNT/polymer composites prepared by a combination of two functionalization approaches: 1) covalent attachment of UPy pendants on the multiwalled CNT surface ( UPy‐MWCNTs ) and 2) directed self‐assembly of UPy‐MWCNTs within polymers bearing UPy pendants ( Bis‐UPy 1 and Bis‐UPy 2 ) by quadruple complementary DDAA–AADD hydrogen‐bond recognition (D=donor, A=acceptor).     

Carbon nanotubes decorated α-Al2O3 containing cobalt nanoparticles for Fischer-Tropsch reaction

A new hierarchical composite consisted of multi-walled carbon nanotubes (CNTs) layer anchored on macroscopic α-Al₂O₃ host matrix was synthesized and used as support for Fischer-Tropsch synthesis (FTS). The composite constituted by a thin shell of a homogeneous, highly entangled and structure-opened carbon nanotubes network and it exhibited a relatively high and fully accessible specific surface area of 76 m²·g^?1, compared with that of 5 m²·g^?1 of the original α-Al₂O₃ support. The metal-support interaction between carbon nanotubes surface and cobalt precursor and high effective surface area led to a relatively high dispersion of cobalt nanoparticles. This hierarchically supported cobalt catalyst exhibited a high FTS activity along with an extremely high selectivity towards liquid hydrocarbons compared with the cobalt-based catalyst supported on pristine α-Al2O₃ or on CNTs carriers. This improvement can attribute to the high accessibility of composite surface area comparing with the macroscopic host structure alone or to the bulk CNTs where the nanoscopic dimension induced a dense packing with low mass transfer which favoured the problem of reactants competitive diffusion towards the cobalt active site. In addition, intrinsic thermal conductivity of decorated CNTs could help the heat dissipating throughout the catalyst body, thus avoiding the formation of local hot spots which appeared in high CO conversion under pure syngas feed in FTS reaction. Cobalt supported on CNTs decorated α-Al₂O₃ catalyst also exhibited satisfied high stability during more than 200 h on stream under relatively severe conditions compared with other catalysts reported in the literature. Finally, the macroscopic shape of such composite easily rendered its usage as catalyst support in a fixed-bed configuration without facing problems of transport and pressure drop as encountered with the bulk CNTs.