Investigations on surface diffusion in sparingly soluble monolayers at the gas/liquid interface using radiotracer technique

Summary A method is proposed for calculating surface selfdiffusion coefficients in sparingly soluble monolayers at fluid interfaces based on radiotracer measurements and allowing for counter geometry. On this basis an analysis of experimental results is possible without having to allow for processes competing with surface self-diffusion. Monolayers of various long-chainn-alcohols andn-alkane-carboxylic acids were studied in the area range between 0.23 nm²/molecule and 2.0 nm²/molecule. Surface self-diffusion coefficientsD _s were determinded only up to areas of 0.75 nm2/molecule since, in case of greater areas, the analysis of surface concentration becomes inexact due to the increasing influence of density convection. For the systems studied,D _s values lie in the order of 10^–5 cm²/s. In all compounds studied, the values ofD _s increase with area per molecule. In addition, dependence on the type of hydrophilic group and alkyl-chain length of monolayer molecules was proved. The results are discussed by means of various model concepts.

---

Zusammenfassung Ein Verfahren zur Berechnung der Oberflächenselbstdiffusionskoeffizienten in schwerlöslichere Monoschichten an fluiden Phasengrenzen auf der Grundlage von Radiotracermessungen und unter Berücksichtigung der Zählrohrgeometrie wird vorgeschlagen. Auf dieser Basis ist eine Auswertung der Experimentalergebnisse möglich, ohne daß zur Oberflächenselbstdiffusion in Konkurrenz stehende Transportvorgänge berücksichtigt werden müssen. Untersucht wurden Monoschichten verschiedener längerkettigern-Alkanole undn-Alkancarbonsäuren im Flächenbereich zwischen 0,23 nm²/Molekül und 2 nm²/Molekül. OberflächenselbstdiffusionskoeffizientenD _s wurden nur bis zu Flächenwerten von 0,75 nm²/Molekül bestimmt, weil bei höheren Flächen die Auswertung der Oberflächenkonzentrationsänderungen wegen des zunehmenden Einflusses von Dichtekonvektion ungenau wird. DieD _s -Werte liegen für die untersuchten Systeme in der Größenordnung 10^–5 cm2/s. Bei allen untersuchten Verbindungen nehmen die Werte von D_s mit steigender Fläche pro Molekül zu. Außerdem wurde die Abhängigkeit von der Art der hydrophilen Gruppe und der Alkylkettenlänge der Monoschichtmoleküle nachgewiesen. Die Ergebnisse wurden anhand verschiedener Modellvorstellungen diskutiert.

---

---

With 8 figures and 1 table     

Nonlinear viscoelasticity of sorbitan tristearate monolayers at liquid/gas interface

The interfacial rheology of sorbitan tristearate monolayers formed at the liquid/air interface reveal a distinct nonlinear viscoelastic behavior under oscillatory shear usually observed in many 3D metastable complex fluids with large structural relaxation times. At large strain amplitudes (gamma), the storage modulus (G') decreases monotonically whereas the loss modulus (G') exhibits a peak above a critical strain amplitude before it decreases at higher strain amplitudes. The power law decay exponents of G' and G' are in the ratio 2:1. The peak in G' is absent at high temperatures and low concentration of sorbitan tristearate. Strain-rate frequency sweep measurements on the monolayers do indicate a strain-rate dependence on the structural relaxation time. The present study on sorbitan tristearate monolayers clearly indicates that the nonlinear viscoelastic behavior in 2D Langmuir monolayers is more general and exhibits many of the features observed in 3D complex fluids.     

Alkane/Alcohol mixed monolayers at the solid/liquid interface

In this work, we present the behavior of solid monolayers of binary mixtures of alkanes and alcohols adsorbed on the surface of graphite from their liquid mixtures. We demonstrate that solid monolayers form for all the combinations investigated here. Differential scanning calorimetry (DSC) is used to identify the surface phase behavior of these mixtures, and elastic neutron incoherent scattering has been used to determine the composition of the mixed monolayers inferred by the calorimetry. The mixing behavior of the alcohol/alkane monolayer mixtures is compared quantitatively with alkane/alkane and alcohol/alcohol mixtures using a regular solution approach to model the incomplete mixing in the solid monolayer with preferential adsorption determining the surface composition. This analysis indicates the preferential adsorption of alcohols over alkanes of comparable alkyl chain length and even preferential adsorption of shorter alcohols over longer alkanes, which contrasts strongly with mixtures of alkane/alkane and alcohol/alcohol of different alkyl chain lengths where the longer homologue is always found to preferentially adsorb over the shorter. The alcohol/alkane mixtures are all found to phase separate to a significant extent in the adsorbed layer mixtures even when molecules are of a similar size. Again, this contrasts strongly with alkane/alkane and alcohol/alcohol mixtures where, although phase separation is found for molecules of significantly different size, good mixing is found for similar size species.     

Miscibility of binary monolayers at the air-water interface and interaction of protein with immobilized monolayers by surface plasmon resonance technique

The miscibility and stability of the binary monolayers of zwitterionic dipalmitoylphosphatidylcholine (DPPC) and cationic dioctadecyldimethylammonium bromide (DOMA) at the air-water interface and the interaction of ferritin with the immobilized monolayers have been studied in detail using surface pressure-area isotherms and surface plasmon resonance technique, respectively. The surface pressure-area isotherms indicated that the binary monolayers of DPPC and DOMA at the air-water interface were miscible and more stable than the monolayers of the two individual components. The surface plasmon resonance studies indicated that ferritin binding to the immobilized monolayers was primarily driven by the electrostatic interaction and that the amount of adsorbed protein at saturation was closely related not only to the number of positive charges in the monolayers but also to the pattern of positive charges at a given mole fraction of DOMA. The protein adsorption kinetics was determined by the properties of the monolayers (i.e., the protein-monolayer interaction) and the structure of preadsorbed protein molecules (i.e., the protein-protein interaction).     

Protein-directed assembly of binary monolayers at the interface and surface patterns of protein on the monolayers

Ferritin-directed assembly of binary monolayers of zwitterionic dipalmitoylphosphatidylcholine and cationic dioctadecyldimethylammonium bromide (DOMA) at the interface and surface patterns of ferritin on the monolayers have been investigated using a combination of infrared reflection absorption spectroscopy, surface plasmon resonance, and atomic force microscopy. Ferritin binding to the binary monolayers at the air-water interface at the surface pressure 30 mN/m, primarily driven by the electrostatic interaction, gives rise to a change in tilt angle of hydrocarbon chains from 15 degrees +/- 1 degrees to 10 degrees +/- 1 degrees with respect to the normal of the monolayer at the mole fraction of DOMA (XDOMA) of 0.1. The chains at XDOMA = 0.3 are oriented vertical to the water surface before and after protein binding. A new mechanism for protein binding to the binary monolayers is proposed. The secondary structures of the adsorbed ferritin are prevented from changing to some extent due to the existence of the monolayers. The amounts of the bound protein on the monolayers at the air-water interface are increased in comparison with those on the pre-immobilized monolayers at low XDOMA. The increased amounts and different patterns of the adsorbed protein at the monolayers are mostly attributed to the formation of multiple binding sites available for ferritin, which is due to the lateral reorganization of the lipid components in the monolayers induced by the protein in the subphase. The created multiple binding sites on the monolayer surfaces through the protein-directed assembly can be preserved for subsequent protein binding.     

Little exchange at the liquid/solid interface: defect-mediated equilibration of physisorbed porphyrin monolayers

The transition from low to high density 2D surface structures of copper porphyrins at a liquid/solid interface requires specific defects at which nearly all exchange of physisorbed molecules with those dissolved in the supernatant occurs.     

Ionization state and structure of l-1,2-dipalmitoylphosphatidylglycerol monolayers at the liquid/air interface

Phosphatidylglycerols are components of biological membranes. The phase behavior of these phospholipids was extensively investigated. However, there is still no definite picture about the dependence of the ionization state and monolayer structure on subphase composition. The major problem of previous investigations is that none of the methods used allow obtaining the ionization degree directly. In the present work we apply techniques developed in the past decades for Langmuir monolayers: infrared reflection absorption spectroscopy (IRRAS) as well as X-ray diffraction and reflectivity techniques, which provide straightforward information about structure and ionization state of a L-1,2-dipalmitoylphosphatidylglycerol (DPPG) monolayer. The Gouy-Chapman model is applied to evaluate the intrinsic pKa. Therewith, the ionization degree can be determined even at low pH values. The experimental titration curves are in good agreement with theoretical curves based on the Gouy-Chapman model. The obtained instrinic pKa amounts to 1. The ionization degree of a DPPG monolayer is independent of the monovalent cation size. In contrast, the structure of a DPPG monolayer is strongly affected by the type of divalent cations.     

Design of surface active soluble peptide molecules at the air/water interface

Surface active molecules collect at interfaces and have the potential to be used for water evaporation reduction. The objective of this work is to design surface active soluble peptides that collect at the air/water interface using molecular simulations. Rotational isomeric state Monte Carlo (RISMC) sampling together with a solvation model that we recently invented, the AAD solvation model [Gu, C.; Lustig, S.; Trout, B. J. Phys. Chem. B 2006, 110 (3), 1476-1484] was applied to calculate the adsorption free energy of the peptide molecule at the air/water interface. The results were validated by both molecular dynamics simulations with an explicit solvent model and surface tension measurements on synthesized peptides. It was demonstrated that this approach is able to give a reasonable prediction of surface activity with an approximately 50% hit rate in terms of designed surface active molecules actually being surface active. The relationship between the chemical composition and the surface morphology is also discussed.     

Nystatin in Langmuir monolayers at the air/water interface

The paper presents a thorough characteristics of Langmuir monolayers formed at the air/water interface by a polyene macrolide antibiotic-nystatin. The investigations are based on the analysis of pi/A isotherms recorded for monolayers formed by this antibiotic at different experimental conditions. A significant part of this work is devoted to the stability and relaxation phenomena. It has been found that nystatin forms at the air/water interface monolayers of the LE state. A plateau region, observed during the course of the isotherm compression, is suggested to be due to the orientational change of nystatin molecules from horizontal to vertical position. Quantitative analysis of the desorption of the monolayer material into bulk water indicates that the solubility of nystatin monolayers increases with surface pressure. At low surface pressures, the desorption of nystatin from a monolayer is controlled both by dissolution and by diffusion. However, at the plateau and in the post-plateau region, the desorption does not achieve a steady state and the monolayer is less stable than in the pre-plateau region. However, the presence of membrane lipids, even at a low mole fraction, considerably increases the stability of nystatin monolayers. This enables the application of the Langmuir monolayer technique to study nystatin in mixture with cellular membrane components, aiming at verifying its mode of action and the mechanism of toxicity.     

Layer-by-layer surface freezing of linear alcohols at the graphite/liquid interface

Differential scanning calorimetry (DSC), incoherent elastic neutron scattering, and neutron diffraction are used to demonstrate the presence of adsorbed solid multilayers of linear alcohols at the graphite-liquid alcohol interface. All alcohols studied (C(5)-C(18)) are found to form at least one monolayer. In addition all the even alcohols investigated (C(6)OH to C(18)OH) show multilayer formation. However, only the short odd alcohols (C(5)OH to C(11)OH) clearly exhibit additional features indicating multilayer formation.     

Expulsion of bovine serum albumin from the air/water interface by a sparingly soluble lecithin lipid

Dynamic surface tensiometry, ellipsometry, and infrared reflection-absorption spectroscopy (IRRAS) were used to study the dynamic adsorption and surface tensions of dilauroylphosphatidylcholine (DLPC) in the presence of bovine serum albumin (BSA). Results show that the equilibrium adsorbed layers consist mostly of DLPC, which can produce dynamic surface tensions (1 mN/m) as low as the more successful lung surfactant replacement formulations. When the aqueous surface expands and contracts sinusoidally, BSA can coadsorb and lead to slightly higher dynamic surface tensions than when DLPC is alone. Similar results were obtained with BSA and sodium myristate [McClellan and Franses, Colloids Surf. B 30 (2003) 1]. Expulsion of the BSA in the layer by DLPC can take from 5 to 15 min, depending on relative concentrations and history of solute addition. This is shown by tensiometry measurements on mixtures, and also by injecting aqueous DLPC underneath adsorbed BSA layers and probing the surface layer with ellipsometry and IRRAS. Albumin layers from buffer solutions aged up to 30 h can be expelled by DLPC. In pure water, there is an initial enhancement in protein adsorption after the DLPC is injected. This can be explained by the hypothesis that DLPC molecules bind with BSA molecules to form a hydrophobic lipoprotein complex, which is more hydrophobic than the protein itself. Since DLPC produces lower surface energy than BSA and--being slightly soluble--adsorbs to the surface by a molecular mechanism, it fulfills the thermodynamic and dynamic requirements for expelling the BSA from the surface. The results have implications for minimizing lung surfactant inhibition by serum proteins, as it occurs in the cases of adult or acute respiratory distress syndrome.     

Reversible activation of diblock copolymer monolayers at the interface by pH modulation, 2: Membrane interactions at the solid/liquid interface

A monolayer of the pH-responsive poly[2-(dimethylamino)ethyl methacrylate-block-methyl methacrylate] diblock copolymer [PDMAEMA-PMMA] was transferred from the air/water interface to a silicon substrate for evaluation as a tunable interlayer between biological material and solid substrates. Specular neutron reflectivity experiments revealed that the weak polyelectrolyte PDMAEMA chains at the solid/liquid interface can be reversibly activated by pH modulation. The thickness, scattering length density, and surface roughness of the polymer film can be systematically controlled by pH titration. As a simple model of plasma membranes, a lipid bilayer was deposited onto the polymer film. The membrane-substrate interaction was characterized by neutron reflectivity experiments, demonstrating that the membrane-substrate distance could be reversibly regulated by pH titration. These results confirm the potential of stimuli-responsive polymers for precise control of cell-surface interactions.     

Poly(itaconates) monolayers behavior at the air/water interface. Study at different surface concentration

Polymer monolayers spread at the air/water interface were obtained for: poly(monooctyl itaconate) (PMOI), poly(monodecyl itaconate) (PMDI), poly(monododecyl itaconate) (PMDoI), poly(monobenzyl itaconate) (PMBzI), poly(methyldodecyl itaconate) (PMeDoI) and the alternating copolymer (monooctyl itaconate-alt-maleic anhydride) (MOI-alt-MA). By monolayer compression at constant temperature, the respective Langmuir isotherms for these polymers were obtained. For all polymers the zero-pressure limiting area per repeating unit (ru) Ao, and the collapse pressure π_c were determined. At low surface polymer concentrations, the monolayers characterization was carried out according to the surface pressure expressed as a function of the surface concentration. The behavior observed was described by the virial expansion development. At the semidilute region, the surface pressure variation was expressed in terms of the scaling laws as a power function of the surface concentration.     

Insoluble monolayers of irisresorcinol at the air/water interface

Monolayer properties of irisresorcinol [5-(cis-10-heptadecenyl) resorcinol] were measured at the air/water interface. TheA-T isobars of the monolayers at 10 and 15 mN/m gave two-dimensional thermal expansivities of 1.4 × 10^–4/K and 1.3 × 10^–4/K at a temperature span from 7–40 C, respectively. The- A isotherms of the material showed only a little dependence on temperature from 5–35 C and onpH except at highpH, where monolayers expanded by ionization of resorcinol headgroups. Some types of saccharose in the subphase exhibited a characteristic interaction with irisresorcinol in monolayers, and there is a possibility that this material will be used for molecular recognition of some saccharoses.     

Analysis of the gas states at a liquid/solid interface based on interactions at the microscopic level

The states of gas accumulated at the liquid/solid interface are analyzed on the basis of the continuum theory, in which the Hamaker constant is used to describe the long-range interaction at the microscopic scale. The Hamaker constant is always negative, whereas the "gas" spreading coefficient can be either negative or positive. Despite the complexity of gas, including that the density profile may not be uniform due to absorption on both solid and liquid surfaces, we predict three possible gas states at the liquid/solid interface, that is, complete "wetting", partial "wetting", and pseudopartial "wetting". These possible gas states correspond, respectively, to a gas pancake (or film) surrounded by a wet solid, a gas bubble with a finite contact angle, and a gas bubble(s) coexisting with a gas pancake. The typical thickness of the gas pancakes is at the nano scale within the force range of the long-range interaction, whereas the radius of the gas bubbles can be large. The state of a gas bubble(s) coexisting with a gas film is predicted theoretically for the first time. Our theoretical results can contribute to the development of a unified picture of gas nucleation at the liquid/solid interface.     

Hydrophilic interactions between organic and water molecules as models for monolayers at the gas/water interface

Model clusters of surfactant prototypes with small number of water molecules are calculated at different levels of theory. All approaches used yield correct trends in the variation of the dipole moment upon tail elongation or polar headgroup variation. Models including one, two, or more water molecules are optimized. The most stable structures are those with maximum number of atoms involved in hydrogen bonding. The normal components of the dipole moment prove to be less sensitive to the nature (aliphatic or aromatic) of the hydrophobic tail, in accord with findings from the phenomenological models. Values of the dipole moment approaching the experimental estimates required inclusion of sufficient aqueous environment (>20 water molecules per hydrophilic head) and of lateral intersurfactant interactions into the model.     

Mixing characterization in batch reactors using the radiotracer technique

The infusion rate of a slug of tracer into an anchor agitated 100-liter batch mixer was characterized by a decay rate constant. This constant was then used to define a dimensionless mixing-rate number which was related to the stirrer Reynolds number. This correlationship allows the calculation of time or rotational speed needed to achieve any desired degree of uniformity of the mixture.^99mTc was used as radiotracer and the mixing process was followed by a scintillation Nal(Tl) counter situated on the reactor wall near the injection point.     

Spectroscopic studies on bilirubin aggregate at liquid/liquid interface

Bilirubin (BR) aggregating at liquid/liquid interface was firstly detected by Fourier transform infrared (FTIR) imaging/spectroscopy combining with ultraviolet-visible (UV/Vis) absorption spectra. In the UV/Vis absorption spectra of BR aggregate, a new shoulder appeared at 474 nm, and BR absorption maximum underwent red shift from 450 nm to a longer wavelength at 497 nm, which indicates that BR aggregate was formed at the interface. Meanwhile, the BR molecule structure changed or conformation torsion, that is, the increase in orbit overlap or dihedral angle and the enhancement of exciton coupling. In the study of FTIR imaging/spectroscopy, the hydrogen bond-sensitive infrared bands of BR aggregate showed remarkable changes in band shift and intensity compared with those of BR powder, suggesting that the intramolecular hydrogen bonds broke out and internal structure changed. These new findings will be helpful for understanding of the BR molecular interaction, transportation, complex with serum albumin and metal ions, and the effect of BR aggregating on biomembrane and human tissues.