XPS and ISS analysis of Fischer-Tropsch catalysts

Summary The surface compositions of K and Cu containing Fe/Mn oxide catalysts for Fischer-Tropsch synthesis were investigated by XPS and ISS. The surface species after calcination are identified as Fe₂O₃, Mn₂O₃, MnO₂, CuO and most likely KO₂, and after in situ reduction at 723 K Fe⁰, Cu⁰, Fe²⁺ and Fe³⁺ oxides, MnO and KOH. Mn and K are enriched on the surfaces after calcination and reduction; the Cu surface content is approximately equal to the bulk concentration. The K enrichment is especially strong and ISS indicates that potassium is mainly confined to the uppermost layers. The degree of reduction of Fe is strongly dependent on the amount of Cu or K. The change in surface composition during Fischer-Tropsch reaction in the XPS equipment can be correlated to the activity of the catalysts. The pure and Cu containing samples show a constant activity and only a small increase in carbon surface concentration. The K containing catalysts deactivate after a short time and are then totally covered by carbon. On all catalyst surfaces a small amount of carbonate is formed.

---

XPS- and ISS-Analyse von Fischer-Tropsch-Katalysatoren

     

Michael addition of 1,3-dicarbonyl compounds catalyzed by iron oxide nanoparticles

Several iron oxides nanoparticles (Fe₂O₃@Fe₂O₃, Fe°@Fe₂O₃, GO@Fe₂O₃ and calcinated Fe₂O₃) have been assessed as catalysts in the 1,4-addition of a cyclic β-ketoester onto methyl vinyl ketone under neat conditions. It appeared that calcinated Fe₂O₃NP are efficient catalysts at 1?mol% loading for the Michael addition of 1,3-dicarbonyl compounds onto various enones.     

Synthesis of Fe3O4, Fe2O3, Ag/Fe3O4 and Ag/Fe2O3 nanoparticles and their electrocatalytic properties

Two important iron oxides:Fe3O4 and Fe2O3,as well as Fe3O4 and Fe2O3 nanoparticles mingling with Ag were successfully synthesized via a hydrothermal procedure.The samples were confirmed and characterized by X-ray diffraction(XRD),and X-ray photoelectron spectroscopy(XPS).The morphology of the samples was observed by transmission electron microscopy(TEM).The results indicated Fe3O4,Fe2O3,Ag/Fe3O4 and Ag/Fe2O3 samples all were nanoparticles with smaller sizes.The samples were modified on a glassy carbon electrode and their elctrocatalytic properties for p-nitrophenol in a basic solution were investigated.The results revealed all the samples showed enhanced catalytic performances by comparison with a bare glassy carbon electrode.Furthermore,p-nitrophenol could be reduced at a lower peak potential or a higher peak current on a glassy carbon electrode modified with Ag/Fe3O4 or Ag/Fe2O3 composite nanoparticles.     

铜物种对Cu/Fe2O3水煤气变换反应催化剂性能的影响

采用共沉淀法制备了系列铜负载量不同的Cu/Fe₂O₃水煤气变换(WGS)催化剂,并考察了铜负载量对催化剂结构和水煤气变换反应性能的影响. 结果表明,Cu/Fe₂O₃催化剂呈现出良好的水煤气反应性能,当CuO质量分数为20%时,催化剂的WGS性能最优,250 ℃时CO转化率高达97.2%,同时热稳定性也最好. 运用X射线粉末衍射(XRD)、N₂物理吸脱附和H₂程序升温还原(H₂-TPR)等手段对Cu/Fe₂O₃催化剂的物相、织构特征及还原性能进行了表征,结果表明,CuFe₂O₄物种的存在极大地改善了催化剂的还原性能和WGS反应活性. 这是由于CuFe₂O₄特殊的尖晶石结构有利于Cu微晶的稳定;同时,CuFe₂O₄在低温下即被还原为单质铜,有利于促进催化剂体系中电子的转移. 此外,通过(NH₄)₂CO₃溶液处理,研究了独立相CuO对Cu/Fe₂O₃催化剂WGS反应性能的影响,结果发现,独立相CuO的存在,有利于H原子在各组分传递,从而促进催化剂的CuFe₂O₄的还原,改善Cu/Fe₂O₃催化剂的WGS反应性能.     

Hydrothermal CO2 Reduction by Glucose as Reducing Agent and Metals and Metal Oxides as Catalysts

High-temperature water reactions to reduce carbon dioxide were carried out by using an organic reductant and a series of metals and metal oxides as catalysts, as well as activated carbon (C). As CO₂ source, sodium bicarbonate and ammonium carbamate were used. Glucose was the reductant. Cu, Ni, Pd/C 5%, Ru/C 5%, C, Fe₂O₃ and Fe₃O₄ were the catalysts tested. The products of CO₂ reduction were formic acid and other subproducts from sugar hydrolysis such as acetic acid and lactic acid. Reactions with sodium bicarbonate reached higher yields of formic acid in comparison to ammonium carbamate reactions. Higher yields of formic acid (53% and 52%) were obtained by using C and Fe₃O₄ as catalysts and sodium bicarbonate as carbon source. Reactions with ammonium carbamate achieved a yield of formic acid up to 25% by using Fe₃O₄ as catalyst. The origin of the carbon that forms formic acid was investigated by using NaH¹³CO₃ as carbon source. Depending on the catalyst, the fraction of formic acid coming from the reduction of the isotope of sodium bicarbonate varied from 32 to 81%. This fraction decreased in the following order: Pd/C 5% > Ru/C 5% > Ni > Cu > C ≈ Fe₂O₃ > Fe₃O₄.     

Fe3O4修饰的Pt-Ru/C纳米催化剂的制备及其在无溶剂条件下邻氯硝基苯选择性加氢的催化性能

采用浸渍法制备了一系列Pt/Ru质量比不同的Fe₃O₄修饰的Pt-Ru/Fe₃O₄/C催化剂, 运用透射电镜(TEM)、能量弥散X射线谱(EDX)、X射线光电子能谱(XPS)、X射线粉末衍射(XRD)等手段对Pt-Ru/Fe₃O₄/C一系列催化剂进行了表征, 并考察了Pt/Ru质量比不同对催化剂Pt-Ru/Fe₃O₄/C在无溶剂条件下催化邻氯硝基苯(o-CNB)选择性加氢制备邻氯苯胺(o-CAN)催化性能的影响. 研究结果表明, 催化剂的催化活性和对目标产物的选择性跟活性组分Pt、Ru比例有关. 随着Pt/Ru比例的减小, 目标产物o-CAN的选择性有所升高, 然而反应物o-CNB的转化率有所下降. 当Pt/Ru的质量比为2时, o-CNB的转化率降为76.5%, 而目标产物o-CAN的选择性仍然为100%. 与此同时, 我们还对Pt-Ru/Fe₃O₄/C催化剂高的催化活性和目标产物的高选择性可能的原因进行了分析.     

DTA,TG studies of catalytic oxidation of carbon particles over M2 III O3 (MIII=Al,Cr, Fe,Ni)

Carbonizate as a model soot has been submitted to oxidation using Al₂O₃, Cr₂O₃, Ni₂O₃ and Fe₂O₃ as catalysts in the temperature range from RT up to 1000°C. The results obtained indicate that Fe₂O₃ is the most active catalyst in soot oxidation. However, all the catalysts examined are active in transformation of carbonizate components. It has been shown that DTA and TG methods can be used as fast methods testing the carbonizate oxidation. This revised version was published online in July 2006 with corrections to the Cover Date.     

Characterization and Activity of Iron-Manganese Catalysts for Carbon Monoxide Hydrogenation

Studies on the structural changes and catalytic behavior of iron-manganese catalysts for CO hydrogenation were conducted using Mossbauer spectroscopy, X-ray diffraction, temperature programmed reduction and kinetic measurements. It was observed that the reduction of the mixed oxide catalyst precursors proceeds via the formation of Fe_3-xMn_xO₄,Mn_3-xFe_xO₄ mixed spinel and Fe_1-zMn₂O mixed oxide to α-iron and MnO. After use for CO hydrogenation, catalysts are oxidized as well as carburized. The Mn_3-yFe_yO₄ mixed spinel and Fe_1-2Mn_zO mixed oxide are the most powerful phases for olefin production. The highest attainable 2–4 low carbon olefin selectivity is 41% with an 86% conversion level. Higher manganese content or lower reduction temperatures may change the carbide formed from χ-Fe₅C₂ to the more unstable ?′-Fe₂₂C. Carbide formation is greatly dependent on manganese content and activation procedure used.     

The activity of dispersed oxides on natural and exfoliated graphite surfaces

Experimental data obtained indicate that ion exchange on the graphite surface can be attributed to impurity oxides. During exfoliated graphite oxidation reactions, inorganic oxides act as catalysts (Fe₂O₃, Cr₂O₃), inhibitors (B₂O₃, Al₂O₃) or are inert.     

Influence of iron oxide support preparation method on the properties of Ru/Fe2O3 catalysts for water-gas shift reaction

Studies were undertaken of phase transitions of iron oxide obtained from iron oxide-hydroxides of type α-, β-, γ- and δ-FeOOH, and used as a support of ruthenium catalysts Ru/Fe₂O₃, employed in the water-gas shift reaction. In asprepared pure supports and ruthenium catalysts the main phase was α-Fe₂O₃. After use in the water-gas shift reaction, the support showed the presence of different phases of iron oxide. The most active Ru/Fe₂O₃ catalysts prepared on the basis of α- and δ-FeOOH, after use in the water-gas shift reaction, revealed the presence of Fe₃O₄ or a mixture of phases Fe₃O₄ and γ-Fe₂O₃. The least active catalysts, prepared on the basis of β- and γ-FeOOH, contained a solid solution of Fe₃O₄-γ-Fe₂O₃ with traces of α-Fe₂O₃.     

Catalytic behavior of supported Pd catalysts in the selective hydrogenation of campholenic aldehyde to naturanol

Selective catalytic reduction of campholenic aldehyde to naturanol was investigated over Sn-and Fe-doped SiO₂, and Fe₂O₃-supported Pd catalysts. On Pd/SiO₂ and Pd-Sn/SiO₂ only saturated campholenic aldehyde is formed. Addition of Fe increases the C=O hydrogenation rate producing the corresponding unsaturated alcohol with a good selectivity. Also Fe₂O₃-supported catalysts were found to be more selective towards carbonyl hydrogenation. Addition of tin to Pd/Fe₂O₃ contributes to a further selectivity enhancement towards naturanol.     

The Influence of Active Carbon Supports Toward the Electrocatalytic Behavior of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> Nanoparticles for the Extended Energy Generation of Mediatorless Microbial Fuel Cells

Magnetite (Fe₃O₄) nanoparticles anchored over the different active carbon supports were developed by a simple wet solution method. The developed nanostructures were magnetically self-assembled over the electrode surface and exploited as anode catalysts in mediatorless microbial fuel cells (MFC). The morphological characterizations revealed that 3～8-nm-sized Fe₃O₄ nanoparticles were homogeneously anchored over the different carbon matrices and the obtained diffraction patterns ensured the cubic inverse spinel structure of prepared Fe₃O₄ nanoparticles. The morphology, size, and structure of Fe₃O₄ nanoparticles anchored over the different active carbon supports were maintained identical, and the influence of active carbon support toward the effectual MFC performances was evaluated under various electrochemical regimes and conditions by using Escherichia coli as a catalytic microorganism. The electrochemical characterizations revealed that carbon nanotube (CNT)-supported Fe₃O₄ nanoparticles exhibited lower charge transfer resistance and high coulombic efficiency in comparison with the graphene and graphite nanofiber-supported composites. Among the studied anode catalysts, Fe₃O₄/CNT composite exhibited the maximum MFC power density of 865 mW m^?2 associated with excellent durability performances, owing to the specific interaction exerted between the microorganisms and the Fe₃O₄/CNT composite. Thus, the binder-free electrode modification process, mediatorless environment, rapid electron transfer kinetics, high power generation, and long durability performances achieved for the developed system paved futuristic dimensions for the high performance MFCs.     

The effect of the nature of the support on catalytic properties of ruthenium supported catalysts in partial oxidation of methane to syn-gas

The effect of the carrier on catalytic properties of ruthenium supported catalysts in partial oxidation of methane (POM) was investigated. A variety of supports differed in texture and reducibility (Al₂O₃, SiO₂, TiO₂, Cr₂O₃, CeO₂ and Fe₂O₃) were used. The catalyst activity is governed by ruthenium phase formation (RuO₂ → Ru⁰), and it depends on redox properties of the support as well as support-ruthenium phase interaction. The activity of Ru supported catalysts decreases in the order Al₂O₃ ≈ SiO₂ > Cr₂O₃ > TiO₂ > CeO₂ > Fe₂O₃. No significant effects of the specific surface area and porosity of catalysts on the methane conversion and selectivity of CO formation were found. The selectivity of CO₂ formation (total oxidation of CH₄) under conditions of POM (a ratio of CH₄/O₂ = 2) is associated with the contribution of reducible support oxides into the catalytic performance.     

CNx-modified Fe3O4 as Pt nanoparticle support for the oxygen reduction reaction

A novel electrocatalyst support material, nitrogen-doped carbon (CN_x)-modified Fe₃O₄ (Fe₃O₄-CN_x), was synthesized through carbonizing a polypyrrole-Fe₃O₄ hybridized precursor. Subsequently, Fe₃O₄-CN_x-supported Pt (Pt/Fe₃O₄-CN_x) nanocomposites were prepared by reducing Pt precursor in ethylene glycol solution and evaluated for the oxygen reduction reaction (ORR). The Pt/Fe₃O₄-CN_x catalysts were characterized by X-ray diffraction, Raman spectra, X-ray photoelectron spectroscopy, scanning electron microscopy, and transmission electron microscopy. The electrocatalytic activity and stability of the as-prepared electrocatalysts toward ORR were studied by cyclic voltammetry and steady-state polarization measurements. The results showed that Pt/Fe₃O₄-CN_x catalysts exhibited superior catalytic performance for ORR to the conventional Pt/C and Pt/C-CN_x catalysts.     

Fe2O3含量对Cu-Fe/铝土矿水煤气变换催化剂结构和性能的影响

利用具有高比表面积和介孔结构的改性铝土矿为载体,采用并流共沉淀法制备不同Fe₂O₃含量的Cu-Fe/铝土矿催化剂。以水煤气变换反应为探针反应,考察了催化剂性能。利用X射线荧光元素分析(XRF)、X射线粉末衍射(XRD)、H₂程序升温还原(H₂-TPR)、CO程序升温脱附(CO-TPD)和X射线光电子能谱(XPS)等对催化剂进行了表征。结果表明:负载的Fe₂O₃能显著提高CuO/改性铝土矿催化剂的水煤气变换活性特别是热稳定性能,且随负载的Fe₂O₃含量增加而提高,当负载量为20%时达到最佳。其原因是负载的Fe₂O₃和CuO之间发生了相互作用,形成了类似于CuFe₂O₄复合氧化物,且随负载的Fe₂O₃含量的增加而增强,这种相互作用同时促进了CuO和Fe₂O₃的还原,抑制了CuO的烧结,进而提高了催化剂的性能。     

Fe2O3含量对Cu-Fe/铝土矿水煤气变换催化剂结构和性能的影响

利用具有高比表面积和介孔结构的改性铝土矿为载体,采用并流共沉淀法制备不同Fe2O3含量的Cu-Fe/铝土矿催化剂。以水煤气变换反应为探针反应,考察了催化剂性能。利用X射线荧光元素分析(XRF)、X射线粉末衍射(XRD)、H2程序升温还原(H2-TPR)、CO程序升温脱附(CO-TPD)和X射线光电子能谱(XPS)等对催化剂进行了表征。结果表明:负载的Fe2O3能显著提高CuO/改性铝土矿催化剂的水煤气变换活性特别是热稳定性能,且随负载的Fe2O3含量增加而提高,当负载量为20%时达到最佳。其原因是负载的Fe2O3和CuO之间发生了相互作用,形成了类似于CuFe2O4复合氧化物,且随负载的Fe2O3含量的增加而增强,这种相互作用同时促进了CuO和Fe2O3的还原,抑制了CuO的烧结,进而提高了催化剂的性能。     

Effect of the matrix composition on the activity of metal oxide catalysts in CVD synthesis of carbon nanotubes

Citrate-nitrate method was used to synthesize (Fe,Co)/MgO-Al₂O₃, (Fe,Mo)/MgO-Al₂O₃, and (CoMo)/MgO-Al₂O₃ catalysts for production of carbon nanotubes. Multi-walled nanotubes were formed on these catalysts by catalytic pyrolysis of a propane-butane mixture.     

Effect of ultra-fine gold particle addition to metal oxides in ethylene oxidation

Oxidation of ethylene was carried out over alumina-supported metal oxide catalysts and highly dispersed gold catalysts, respectively, under atmospheric pressure. The ethylene was completely oxidized to produce carbon dioxide and water with both metal oxide and gold catalysts. The activity of gold catalyst prepared by deposition method was much higher than that of supported metal oxide catalysts. Ultra-fine gold particles on Co₃O₄ were more active than on Al₂O₃. Fe₂O₃/Al₂O₃ and MnO₂/Al₂O₃ catalysts were more active than MoO₃/Al₂O₃ catalyst. The activity of the supported metal oxide catalysts was greatly enhanced by addition of gold particles. It was therefore considered that gold particles promote dissociative adsorption of oxygen and the adsorbed oxygen reacts with adsorbed ethylene on support adjacent to the active site.     

Milling Down to Nanometers: A General Process for the Direct Dry Synthesis of Supported Metal Catalysts

Supported catalysts are among the most important classes of catalysts. They are typically prepared by wet‐chemical methods, such as impregnation or co‐precipitation. Here we disclose that dry ball milling of macroscopic metal powder in the presence of a support oxide leads in many cases to supported catalysts with particles in the nanometer size range. Various supports, including TiO₂, Al₂O₃, Fe₂O₃, and Co₃O₄, and different metals, such as Au, Pt, Ag, Cu, and Ni, were studied, and for each of the supports and the metals, highly dispersed nanoparticles on supports could be prepared. The supported catalysts were tested in CO oxidation, where they showed activities in the same range as conventionally prepared catalysts. The method thus provides a simple and cost‐effective alternative to the conventionally used impregnation methods.     

煅烧温度对Mn改性γ-Fe2O3催化剂结构及低温SCR脱硝活性的影响

采用共沉淀法,在不同煅烧温度下制备一系列Mn改性γ-Fe₂O₃催化剂(Fe_0.7Mn_0.3O_z),研究了煅烧温度对Fe_0.7Mn_0.3O_z催化剂低温SCR脱硝活性的影响,并借助XRD、N₂吸附-脱附、EDS及SEM等手段对催化剂进行表征。结果表明,350 ℃煅烧所得Fe_0.7Mn_0.3O_z催化剂的低温SCR活性最佳,在70 ℃时取得92%的NO_x转化率,100~200 ℃可维持100%的NO_x转化率,而450 ℃煅烧所得催化剂的低温SCR活性最低;煅烧温度为350 ℃时,催化剂具有最大的比表面积和比孔容、发达的孔隙结构及适当结晶度的γ-Fe₂O₃,而煅烧温度为400或450 ℃时,催化剂发生烧结且有α-Fe₂O₃生成,不利于低温SCR反应的进行,因此,Fe_0.7Mn_0.3O_z催化剂的最佳煅烧温度为350 ℃。