The effect of C<Subscript>60</Subscript> fullerene on the toughening of epoxy compositions

The effect of C₆₀ fullerene on the mechanical properties of epoxy resins has been investigated. It is found that this filler affects the tensile modulus and tensile strength of epoxy compositions only slightly, but their impact strength at a 0.01–0.12 wt.% content of C₆₀ increases by about 100–200%. A molecular mechanism of the toughening effect of C₆₀ on epoxy resins is suggested.     

Adhesive ability of a heat-resistant double-chain polymer and the strength of CFRP based on it

The adhesive ability of a heat-resistant polyiminoquinazolindione (PIQD) binder, based on a double-chain polymer, and the physicomechanical characteristics of unidirectional CFRPs made with it are investigated. It is shown that, at room temperature, the strength of model adhesive joints (PIQD-steel wire) and of the CFRPs in shear and bending is rather low — about half of that of similar specimens based on an epoxy binder. At the same time, all their mechanical characteristics, to a large measure (50%), are retained at temperatures up to 450°C, which considerably exceeds the heat resistance of all polymer matrices used at the present time. The elastic modulus of the CFRPs in bending practically remains the same up to 450°C. __________ Translated from Mekhanika Kompozitnykh Materialov, Vol. 44, No. 4, pp. 535–546, July–August, 2008.     

Influence of the concentration of carbon nanotubes (CNT) on the thermophysical properties of epoxy/CNT nanocomposites at low temperatures

The influence of the content of carbon nanofillers (multi-and single-wall nanotubes) on the thermophysical properties of epoxy nanocomposites was investigated on the temperature range from −150 to 150°C. A “plateau” was found to exist in the concentration dependence of thermal conductivity on the concentration interval from 0.1 to 1.0 wt.% carbon nanotubes (CNTs). The thermal conductivity of the CNT composites exceeded that of pure epoxy resin by about 40%. A further increase in CNT content de creased the conductivity, owing to increasing interfaces between the two phases and the additional thermal resistance caused by phonon scattering on them. It is found that the temperature interval of transition of the composite from a glassy to a viscoelastic state greatly depends on the filler type and concentration. There exists a critical concentration at which a drop in the glass-transition temperature by 30% can be observed. The reason is the undercure of binder as a result of interaction between CNTs and epoxy macromolecules, which reduces the cross-linking density of structure of the polymer. Translated from Mekhanika Kompozitnykh Materialov, Vol. 44, No. 5, pp. 697–708, September–October, 2008.     

Numerical modeling of deformation and fracture of a multiphase polymer concrete

A numerical method for predicting the deformational and strength characteristics of a calcite-quartzitic polymer concrete from the known properties of its components is developed based on the finite-element method. Components of the material are assumed elastic and isotropic, and the filler particles are modeled by round inclusions perfectly bonded to the polymer matrix. The size distribution of the inclusions correspond to that of actual fillers. The destruction process of the components is simulated by sequentially excluding the particles in which the maximum principal stress has achieved the ultimate value for this component. A comparison of calculated and experimental characteristics of the polymer concrete showed errors of 2–4% for the elastic modulus and about 10% for the ultimate strength if the finite-element cell included not less than 20–30 average-size particles and 2–5 large ones. __________ Translated from Mekhanika Kompozitnykh Materialov, Vol. 42, No. 6, pp. 817–824, November–December, 2006     

Operational properties of a heat-insulation composite with expanded polystyrene crumbs

The operational properties (strength, heat conductivity, hygroscopic sorption, vapor permeability, and frost resistance) of a heat-insulation composite of density 150–350 kg/m³ are investigated. The matrix consists of an aerated concrete substance and a disperse filler of expanded polystyrene crumbs obtained by crushing the household polystyrene package waste. The macro-and microstructure of the composite are considered. It is found that the operational properties of the material directly depend on its density, determined by the amount of the cementing substance in the matrix. __________ Translated from Mekhanika Kompozitnykh Materialov, Vol. 44, No. 4, pp. 591–604, July–August, 2008.     

Formation of a transition layer on the fillers of polymer composites

Based on a plane model of composites, the effect of a transition layer on the elastic modulus E_c of the composites is analyzed in the case where, under the action of a load, the transition layer is formed both on the side of matrix and filler. In evaluating E_c, it is assumed that the elastic modulus in the layer grows linearly from the elastic modulus of matrix to that of filler, but pores in the filler are impermeable to matrix macromolecules. Analytic relation ships are found which allow one to determine the volume fractions of the transition layer on the side of matrix and filler if the experimental elastic modulus of the composite is known. These relationships are used to find the magnitude of the layer in epoxy composites with various fillers and to evaluate its effect on the compressive elastic modulus of the composites. __________ Translated from Mekhanika Kompozitnykh Materialov, Vol. 42, No. 5, pp. 693–700, September–October, 2006.     

Correlation between the strength of fiber-reinforced plastics and the adhesive strength of fiber—Matrix joints

The relationship between the strength (σc) of unidirectional fiber-reinforced plastics in different stressed states and the interfacial strength of their components is investigated. The shear adhesive strength (τ0) of fiber—matrix joints determined by the pull-out technique is used as a measure of the interfacial strength. To obtain the correlation curves betweenσc andτ0, the experimental results are used, where both the plastic and adhesive strength change under the influence of a single factor. In this case, such factors are the fiber surface treatment, nature and composition of polymer matrices, and test temperature. It is shown that the strength of the glass, carbon, and boron plastics increases practically linearly with increased interfacial strength. Such a behavior is observed in any loading conditions (tension, shear, bending, and compression). Sometimes, a small (10–20%) increase in the adhesive strength induces a significant (50–70%) growth in the material strength. Therefore, the interface is the “weak link” in these composites. The shape of theσc—τ0 curves for composites based on the high-strength and high-modulus aramid fibers and different thermoreactive matrices depends on the nature of the fiber and the type of stress state. In many cases, the composite strength does not depend on the interfacial strength. Then, the fiber itself is the “weak link” in these composites. Submitted to the 11th International Conference on Mechanics of Composite Materials (Riga, June 11–15, 2000). Translated from Mekhanika Kompozitnykh Materialov, Vol. 36, No. 3, pp. 291–304, May–June, 2000.     

Influence of nanofillers on the thermal and mechanical behavior of DGEBA-based adhesives for bonded-in timber connections

Results of an experimental investigation into the thermal behavior and mechanical properties of a room-temperature-cured epoxy adhesive (diglycidyl ether of bisphenol A, DGEBA) cross-linked with polyetheramines and filled with different fillers, namely nanosilica, liquid rubber (CTBN), and clay, are reported. The nanosilica and liquid rubber increased the flexural strength and elastic modulus of the adhesive systems; the addition of clay particles raised the elastic modulus significantly, but embrittled the adhesive. Establishing a correct cure time is very important for bonded-in timber structures, as it will affect the bond strength. A study on the effect of cure time on the flexural strength was carried out, from which it follows that the adhesives should be cured for at least 20 days at room temperature. The damping characteristics and the glass-transition temperature of the adhesives were determined by using a dynamic mechanical thermal analysis. The results showed that the filled adhesives had a higher storage modulus, which was in agreement with the elastic moduli determined from static bending tests. The introduction of the fillers increased its glass-transition temperature considerably. Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 42, No. 5, pp. 599–614, September–October, 2006.     

Temperature dependence of the strength of adhesive joints based on crystalline polymer adhesives

The temperature dependence of the stripping strength of adhesive joints between steel and dural plates using crystalline polymers as adhesive (mixed polyamide-4, 5, 8 and guttapercha, both unfilled and filled with an inert filler) has been investigated. The temperature-strength curves pass through two local maxima, near the glass transition temperature of the crystalline adhesive and near its melting point. It is shown that the presence of a high-temperature maximum is determined by recrystallization of the polymer in the overstressed zone at the tip of the developing crack. The relationship between temperature and strength in adhesive joints based on crystalline polymer adhesives is very pronounced in both cohesive and adhesive failure. It is shown that the addition of filler reduces the recrystallization stress of guttapercha.Mekhanika Polimerov, Vol. 1, No. 3, pp. 63–67, 1965     

Effect of dispersed filter particles on the strength behavior of composites

An attempt is made to find a solution by which the effect of neighboring filler particles on the strength of composites could be indirectly estimated. The stresses in composites with a great amount of filler are calculated. Composites based on epoxy-resin binder are tested. A comparison of different models shows that the modified Kerner model reflects only the tendency for the compression strength to change with the degree of filling. The relations between the compression strength and the degree of filling are better described by models allowing for constraint of the plastic deformations of the matrix. However, in this case, the effect of the neighboring particles is not properly taken into account. Translated from Mekhanika Kompozitnykh Materialov, Vol. 35, No. 5, pp. 575–584, September–October, 1999.     

Dispersion of strength properties and reliability of glued joints

The effect of various factors on the dispersion of the strength characteristics of glued joints is examined. A study of aluminum alloys bonded with type EPTs-1 cold-cured epoxy adhesive has shown that such factors as the presence of a filler, the filler particle size, and supplementary heat treatment of the glued joint have a considerable effect on the dispersion of the strength characteristics. It is established that a decrease in filler particle size and supplementary heat treatment reduce the dispersion of the strength characteristics and, correspondingly, increase the reliability of the joints. The experimental data are analyzed by the methods of mathematical statistics.Mekhanika Polimerov, Vol. 1, No. 5, pp. 78–84, 1965     

Effect of surface modification of fibers with a polymer coating on the interlaminar shear strength of a composite and the translation of fiber strength in an F-12 aramid/epoxy composite vessel

The surface of aramid fibers was modified with a polymer coating — a surface treatment reagent containing epoxy resin. The resulting fibers were examined by using NOL tests, hydroburst tests, and the scanning electron microscopy. The modified fibers had a rougher surface than the untreated ones. The interlaminar shear strength of an aramid-fiber-reinforced epoxy composite was highest when the concentration of polymer coating system was 5%. The translation of fiber strength in an aramid/epoxy composite vessel was improved by 8%. The mechanism of the surface treatment of fibers in improving the mechanical properties of aramid/epoxy composites is discussed. Russian translation publeshed in Mekhanika Kompozitnykh Materialov, Vol. 42, No. 6, pp. 729–738, November–December, 2006.     

Thermal conductivity of micro-and nanostructural epoxy composites at low temperatures

The thermal conductivity of epoxy composites containing not only the traditional fillers quartz, talc, carbon black, and aerosil, but also the very promising carbon nanomaterials is investigated. Two kinds of carbon nanomaterials — multi-wall (MWNT) and single-wall (SWNT) carbon nanotubes — were considered. The influence of their content (from 0.05 to 3.0 wt.%) on the thermal conductivity of MWNT-epoxy composites was studied. The thermal conductivity of epoxy composites was examined in the temperature range from −150 to 150°C. It was found that the introduction of 0.1–1.0 wt.% MWNT enhanced the thermal conductivity of pure epoxy resin by about 40%. A further increase in content of the nanotubes decreased the thermal conductivity. This can be explained by the worsening of nanotube dispersion at their high concentrations. The maximum growth in the thermal conductivity of the epoxy composites, on the entire range of temperatures considered, was observed at a 0.1 wt.% content of MWNT. __________ Translated from Mekhanika Kompozitnykh Materialov, Vol. 44, No. 1, pp. 117–126, January–February, 2008.     

Estimation of the macroscopic stress-strain curve of a particulate composite with a crosslinked polymer matrix

The main focus of the present paper is the estimation of the macroscopic stress–strain behavior of a particulate composite. A composite with a cross-linked polymer matrix in a rubbery state filled with an alumina-based mineral filler is investigated by means of the finite-element method. The hyperelastic material behavior of the matrix is described by the Mooney–Rivlin material model. Numerical models on the basis of unit cells are developed. The existence of a discontinuity (breaking) in the matrix at higher loading levels is taken into account to obtain a more accurate estimate for the stress–strain behavior of the particulate composite investigated. The numerical results obtained are compared with an experimental stress–strain curve, and a good agreement is found to exist. The paper can contribute to a better understanding of the behavior and failure of particulate composites with a polymer matrix.     

Plane problems of stability of composite materials with a finite-size filler

The plane problem of three-dimensional stability is solved for a transversely compressed composite material reinforced with ribbons taking into account the inhomogeneous initial state. An approximate solution of the problems is based on the net method. The effect of the ribbon form factor, the ratio between the elastic moduli of the matrix and filler, and Poisson ratio of the filler on the critical deformation of the material is investigated. Translated from Mekhanika Kompozitnykh Materialov, Vol. 36, No. 1, pp. 77–86, January–February, 2000.     

Adhesion between Epoxy-Polysulfone Blends and Fibers

The adhesive strength of a fiber-polymer interface is determined, where epoxy resin blends and linear heat-resistant thermoplastics - polysulfone (PSF) and polyetherimide (Ultem) - are used as matrices. Steel wire and polyamide (nylon-6) fibers are taken as reinforcing fillers. It is shown that the addition of PSF to epoxy resin results in a maximum on the concentration curve corresponding to a 10% PSF content. It is also found that the adhesive strength of the ED-20+Ultem-steel wire interface is practically independent of the modifier content under low (up to 10%) Ultem concentrations.     

Effect of anisometry of a platelike nanofiller on the elastic constants of a transversely isotropic composite

Analysis results for the elastic properties of a composite with a small amount of coplanarly arranged platelike filler particles are presented. The geometrical form of the particles is described by an oblate ellipsoid of revolution. The calculations are performed by formulas obtained by using the Eshelby approach for media with a low concentration of inclusions. The effect of anisometry of the ellipsoidal particles and of the ratio between the elastic moduli of the filler and matrix on the effective elastic constants of the composite is discussed. Calculation results are compared with experimental data for the elastic moduli of a nanocomposite containing completely exfoliated particles of an unmodified montmorillonite. __________ Translated from Mekhanika Kompozitnykh Materialov, Vol. 44, No. 4, pp. 493–504, July–August, 2008.     

The Effect of an Active Diluent on the Properties of Epoxy Resin and Unidirectional Carbon-Fiber-Reinforced Plastics

The influence of an active diluent on the properties of an epoxy matrix and carbon-fiber-reinforced plastics (CFRP) is investigated. The physicomechanical properties of an ED-20 epoxy resin modified with diglycidyl ether of diethylene glycol (DEG-1), the adhesion strength at the epoxy matrix–steel wire interface, and the mechanical properties of unidirectional CFRP are determined. The concentration of DEG-1 was varied from 0 to 50 wt.%. The properties of the matrix, the interface, and the composites are compared. It is stated that the matrix strength affects the strength of unidirectional CFRP in bending and not their strength in tension, compression, and shear. The latter fact seems somewhat unexpected. The interlaminar fracture toughness of the composites investigated correlates with the ultimate elongation of the binder. A comparison between the concentration dependences of adhesion strength and the strength of CFRP shows that the matrices utilized provide such a high interfacial strength that the strength of CFRP no longer depends on the adhesion of its constituents.     

Creep and Long-Term Strength of Press-Powder Composites

The mechanical state of a press-powder filler for pyroautomatics system units of aerospace equipment during their long-term storage is investigated. With the use of the endochronic approach, the rheological properties of a dispersedly reinforced composite are simulated based on the conceptions of linear and nonlinear creep. Analytical expressions of constitutive relations of creep and strength for the composites are obtained. __________ Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 6, pp. 803–818, November–December, 2005.     

Effect of fillers on the structure and properties of cured resins

The elastic (modulus of elasticity and equilibrium high-elastic modulus) and thermal (volume coefficients of thermal expansion below and above the glass transition temperature) properties of compositions based on ÉD-5 epoxy resin cured with polyethylenepolyamine have been investigated. Quartz powder and aluminoborosilicate glass powder were employed as fillers at concentrations from 0 to 0.413. The thermal expansion coefficients of the compositions were studied in a dilatometer, in which the specimen is free of mechanical loads. The Young's modulus at 25°C and the equilibrium high-elastic modulus at 125°C of the compositions were determined in the compression regime in an instrument based on the IZV-2 optical length gage. The thermal expansion coefficients of the polymer matrix were calculated with allowance for the elastic properties of the resin and the filler. It is shown that, as the filler concentration increases, the thermal and elastic properties of the resin in the filled system change. This can be interpreted as a change in the properties of the resin as it approaches the surface of the filler particles. Increased interaction between the filler surface and the epoxy resin tends to stiffen the polymer network.Scientific Research Institute of Precision Technology, Moscow. Translated from Mekhanika Polimerov, No. 6, pp. 1018–1022, November–December, 1969.