Determination of total iron in fresh waters using flow injection with potassium permanganate chemiluminescence detection

A flow injection method is described for the determination of iron in fresh water based on potassium permanganate chemiluminescence detection via oxidation of formaldehyde in aqueous hydrochloric acid. Total iron concentrations are determined after reducing Fe(III) to Fe(II) using hydroxylamine hydrochloride. The detection limit (three standard deviations of blank) is 1.0 nM, with a sample throughput of 120 h⁻¹. The calibration graph was linear over the range (2–10) × 10⁻⁷ M (r ² = 0.9985) with relative standard deviations (n = 5) in the range 1.0–2.3%. The effect of interfering cations (Ca(II), Mg(II), Zn(II), Ni(II), Co(II), Fe(III), Mn(II), Pb(II), and Cu(II)) and common anions (Cl⁻, SO ₄ ²⁻ , PO ₄ ³⁻ , NO ₃ ⁻ , NO ₂ ⁻ , I⁻, F⁻, and SO ₃ ²⁻ ) was studied at their maximum admissible concentrations in fresh water. The method was applied to fresh-water samples from the Quetta Valley, and the results obtained (0.04 ± 0.001–0.11 ± 0.01 mg/L Fe(II)) were in reasonable agreement with those obtained using the spectrophotometric reference method (0.05 ± 0.01–0.12 ± 0.02 mg/L Fe(II)). The text was submitted by the authors in English.     

Simple and Selective Spectrophotometric Method for the Determination of Iron (III) and Total Iron Content, Based on the Reaction of Fe(III) with 1,2-Dihydroxy-3,4-Diketocyclo-Butene (Squaric Acid)

 Squaric acid (1,2-dihydroxy-3,4-diketo-cyclobutene) is used in a specific reaction with Fe(III) for the spectrophotometric determination of Fe(III) and total iron content. The optimization of the experimental parameters leads to the establishment of a simple, fast and accurate analytical method. The analytical procedure includes mixing ammonium squarate (40 mM), prepared in a phthalate buffer solution of pH 2.7, with the sample and measuring the absorbance at 515 nm. The molar absorptivity of the colored product is 3.95×10³ L·mol⁻¹·cm⁻¹, at 515 nm. Calibration graphs for Fe(III) are rectilinear for 0.5–20 mgL⁻¹, with a detection limit of 0.3 mgL⁻¹ and r.s.d. not exceeding 2.5%, for five replicates of a 3.0 mgL⁻¹ standard solution. The method has been successfully applied to the determination of iron (III) and the total iron content after quantitative oxidation of iron (II). The results for several analyzed samples when compared with those acquired by using the FAAS technique, were found to be in satisfactory agreement. Author for correspondence: University of Ioannina, Department of Chemistry, Laboratory of Analytical Chemistry, Ioannina 451 10, Greece. E-mail: panavelt@cc.uoi.gr Received July 27, 2002; accepted December 20, 2002 Published online April 11, 2003     

Photometric determination of aqueous cobalt (II), nickel (II), copper (II) and iron (III) with 1-nitroso-2-naphthol-3,6-disulfonic acid disodium salt in gelatin films

Photometric determination of aqueous Co(II), Cu(II), Ni(II) and Fe(III) was performed using indicator films prepared by immobilization of 1-nitroso-2-naphthol-3,6-disulfonic acid disodium salt (NRS) into hardened photographic film. Immobilization was based on electrostatic interaction of reagent and metal complexes with the gelatin. The isoelectric point pH of hardened gelatin (4.46±0.04) was evaluated by viscometry. Co(II), Fe(III), Ni(II) form 1:3 complexes with NRS in gelatin at pH 2 and Cu(II) forms 1:2 complexes. Their log β′ values were: Co-6.7, Fe-8.6, Cu-8.0, and Ni-6.4. The absorption maxima were: 370nm for NRS, and 430nm, 470nm, 495nm and 720nm for complexes of Co(II), Ni(II), Cu(II) and Fe(III). An algorithm for their simultaneous determination using the indicator films was developed. The detection limits were: c_lim(Co²⁺) = 0.45×10⁻⁵ M, c_lim(Fe³⁺) = 0.50×10⁻⁵ M, c_lim(Cu²⁺) = 0.67×10⁻⁵ M, c_lim(Ni²⁺) = 0.75×10⁻⁵ M,; and their sum c_lim(ΣMn⁺) = 0.82×10⁻⁵ M.      

2-Oximinodimedone monoguanylhydrazone as spectrophotometric reagent for determination of iron

The synthesis, properties and analytical possibilities of 2-oximinodimedone monoguanylhydrazone as spectrophotometric reagent have been examined. A new method for the determination of iron has been developed in a concentration range varying from 0·2–5·0 ppm of iron; the molar absorptivity is 1·1×10⁴ litres mol⁻¹ cm⁻¹ at 600 nm and the relative error is ±0·3%. The method has been applied satisfactorily to the determination of iron in different inorganic samples.     

Sorption behavior of Sn(II) onto Haro river sand from aqueous acidic solutions

The sorption behavior of Sn(II) onto Haro river sand has been examined with respect to nature of electrolyte, agitation time, dosage of sorbent and concentration of sorbate. Maximum sorption (95.5%) has been achieved from 0.034M hydrochloric acid solution after equilibrating sorbate (2·10⁻⁵M) and sorbent (50 mg) for 120 minutes at aV/W ratio of 90 cm³·g⁻¹. The kinetic data have been subjected to Morris-Weber and Lagergren equations. The kinetics of sorption proceeds a two stage process consisting of a relatively slow initial uptake followed by a much rapid increase in the sorption. The rate constant of intraparticle transport, K_d, comes out to be 8.75·10⁻⁸ mol·g⁻¹·min^−1/2 and the first order rate constant for sorption is 0.0416 min⁻¹. The sorption data of Sn(II) onto Haro river sand followed Langmuir, Freundlich and Dubinin-Radushkevich (D-R) type isotherms. The Langmuir constant,Q, related to sorption capacity and,b, related to sorption energy are computed to be 10.6±1.1 μmol·g⁻¹ and 1123±137 dm³·mol⁻¹, respectively. The D-R isotherm yields the values ofC _m=348±151 μmol·g⁻¹ and β=−0.01044±0.0008 mol²·kJ⁻² and ofE=6.9±0.3 kJ·mol⁻¹. In all three isotherms correlation factor (γ) is ≥0.99. The influence of common anions and cations on the sorption has been investigated. Zn(II), Mg(II), oxalate, Pb(II), Mn(II) and tartrate reduce the sorption significantly whereas Fe(II) causes substantial increase in the sorption. It is essential that all ions causing a decrease in the sorption of Sn(II) must be absent from the sorptive solution otherwise low sorption yields would result.     

Determination of chromium in blood by neutron activation analysis

A procedure for the determination of chromium in blood has been developed with a sensitivity of 5×10⁻³ μg Cr. Dried blood was irradiated with a neutron flux of 10¹² n·cm⁻²·sec⁻¹ in the VVRS reactor for 4 weeks, then the sample was mineralized and the chromium isolated by extraction as perchromic acid. The determination of the chromium content was accomplished by measuring the 0.32 MeV gamma energy of⁵¹Cr. In order to make correction for the interfering reaction⁵⁴Fe(n,α)⁵¹Cr, the formation of chromium from high-purity iron was investigated. The chromium content of the blood samples was between 1.03×10⁻² and 5.2×10⁻² ppm Cr.     

Adsorption syntax of Au(III) on unloaded polyurethane foam

The nature of adsorption behavior of Au(III) on polyurethane (PUR) foam was studied in 0.2M HCl aqueous solution. The effect of shaking time and amount of adsorbent were optimized for 3.16·10⁻⁵M solution of Au(III) in 0.2M HCl. The classical Freundlich and Langmuir adsorption isotherms have been employed successfully. The Freundlich parameters 1/n and adsorption capacityK are 0.488±0.016 and (1.40±0.22)·10⁻² mol·g⁻¹, respectively. The Langmuir constants of saturation capacityM and binding energyb are (1.66±0.08)·10⁻⁴mol·g⁻¹ and 40294±2947 l·g⁻¹, respectively, indicating the monolayer chemical sorption. The mean free energy (E) of adsorption of Au(III) on PUR foam has been evaluated using D-R isotherm and found to be 11.5±0.16 kJ·mol⁻¹ reflecting the ion exchange type of chemical adsorption. The effect of temperature on the adsorption has also been studied. the isosteric heat of adsorption was found to be 44.03±1.66 kJ·mol⁻¹. The thermodynamic parameters of ΔG, ΔH, ΔS and equilibrium constantK _c have been calculated. The negative values of ΔG, ΔH and ΔS support that the adsorption of Au(III) on PUR foam is spontaneous, exothermic and of ion exchange chemisorption. The nature of the Au(III) species sorbed on PUR foam have been discussed.     

The extraction of Cr(III) from aqueous thiocyanate solutions and its separation from Co(II) and Ni(II)

For the system liquid anion-exchanger—Cr(III)−NCS⁻, an investigation has been made of the dependence of the percentage extraction of Cr(III) on parameters such as standing time of the Cr(III)−NCS⁻ solution, temperature, pH and type of exchanger. Quantitative extraction of e.g. 4·10⁻⁴ M Cr(III) by 0.1M Aliquat in CCl₄ is easily achieved at room temperature, using 4.75M KNCS−0.05N HCl as aqueous phase. At high Cr(III) concentrations, the complex anion present in the organic phase is Cr(NCS) ₆ ³⁻ ; when working with dilute metal ion solutions, the species extracted is Cr(NCS)₄ (H₂O) ₂ ⁻ . Separations of mixtures containing 10⁻²−10⁻⁴ M Co(II), Ni(II) and Cr(III) have successfully been accomplished.     

An “off–on” fluorescence probe for chromium(III) ion determination in aqueous solution

An “off–on” rhodamine-based fluorescence probe for the selective signaling of Cr(III) has been designed by exploiting the guest-induced structure transform mechanism. This system shows a sharp Cr(III)-selective fluorescence enhancement response in 100% aqueous system under physiological pH value and possesses high selectivity against the background of environmentally and biologically relevant metal ions including Cr(VI), Al(III), Fe(III), Cd(II), Co(II), Cu(II), Ni(II), Zn(II), Mg(II), Ba(II), Pb(II), Na(I), and K(I). Under optimum conditions, the fluorescence intensity enhancement of this system is linearly proportional to Cr(III) concentration from 5.0 × 10⁻⁸ to 7.0 × 10⁻⁶ mol L⁻¹ with a detection limit of 1.6 × 10⁻⁸ mol L⁻¹.     

Adsorptive Voltammetric Studies on the Cerium(III)–Alizarin Complexon Complex at a Carbon Paste Electrode

A novel procedure was developed for the determination of trace cerium on the basis of anodic adsorption voltammetry of the Ce(III)–alizarin complexon (ALC) complex at a carbon paste electrode (CPE). The procedure is convenient to determine cerium individually in the presence of other rare earths because there is a 100 mV difference between the peak potentials of Ce(III)–ALC and other rare earth(III)–ALC complexes in a supporting electrolyte of 0.08 M HAc–NaAc and 0.012 M potassium biphthalate (pH 4.7) when performing linear-scanning from −0.2 to 0.8 V (vs. SCE) at 100 mV/s. The second-order derivative peak currents are directly proportional to the Ce(III) concentration over a range of 6.0 × 10⁻⁹–3.0 × 10⁻⁷ M. The detection limit is as low as 2.0 × 10⁻⁹ M (S/N = 3) for a 120 s preconcentration. An RSD of 3.5% was obtained for 15 determinations of Ce(III) at a concentration of 4.0 × 10⁻⁸ M on the same CPE surface. The method was applied successfully to the determination of cerium in samples of rare earth nodular graphite cast iron.     

Spectrophotometric and polarographic studies of pyridin-2-aldehyde guanylhydrazone-Fe(II) system

The analytical properties of iron(II)-PAG system are described. The optimal conditions for a spectrophotometric determination of iron are

shown. A determination of Fe(II) with PAG can be performed in a concentration range varying from 0.5 to 4.7 ppm of iron, the molar absorptivity is 1.3 × 10⁴ liters · mol^?1, at 380 nm and the relative error (95% confidence level) is ±0.3% for 1.9 ppm of iron.A polarographic behavior of iron(II)-PAG system has been attempted. Iron gives well-defined diffusion-controlled reduction wave with half-wave potential ?0.42 V at 8.5 pH value. The electrode process is discussed.     

Azide-selective sensor based on tripodal iron complex for direct azide determination in aqueous samples

A potentiometric azide-selective sensor based on the use of iron(III) hydrotris(3,5-dimethylpyrazolyl)borate acetylacetonate chloride [Tp^Me2Fe(acac)Cl] as a neutral carrier for an azide-selective electrode is reported. Effect of various plasticizers, viz. o-nitrophenyloctyl ether (o-NPOE), dioctylphthalate (DOP), dibutylphthalate (DBP), and benzylacetate (BA), and an anion excluder, hexadecyltrimethylammonium bromide (HTAB), with [Tp^Me2Fe(acac)Cl] complex in poly(vinyl chloride) (PVC) were studied. The best performance was obtained with a membrane composition of [Tp^Me2Fe(acac)Cl]/HTAB/DOP/PVC in a ratio of 5:2:190:100 (w/w). The sensor exhibits significantly enhanced selectivity toward azide ions over the concentration range 6.3 × 10⁻⁷ to 1.0 × 10⁻² M with a lower detection limit of 3.8 × 10^–7 M and a Nernstian slope of 59.4 ± 1.1 mV decade⁻¹. Influences of the membrane composition, pH and possible interfering anions were investigated on the response properties of the electrode. Fast and stable response, good reproducibility, long-term stability and applicability over a wide pH range (3.5–9.0) are demonstrated. The sensor has a response time of 14 s and can be used for at least 45 days without any considerable divergence in the potential response. The proposed electrode shows fairly good discrimination of azide from several inorganic and organic anions. It was successfully applied to the direct determination of azide in orange juice, tea extracts and human urine samples.     

Differential pulse polarographic determination of Co(II) using moxifloxacine

The polarographic reduction of Co(II) in the presence of moxifloxacin (1-cyclopropyl-7-[(S,S)-2.8-diazabicyclo[4.3.0]non-8-yl]-6-fluoro-8-methoxy-1.4-dihydro-4-oxo-3-quinolinecarboxylic acid) gives rise to an additional adsorption peak corresponding to the reduction of Co(II)-moxifloxacin complex on the mercury drop electrode at −1.17 V. This new peak is applicable to Co(II) determination with the linearity proportional to the Co(II) concentration in the range of 4.93 × 10⁻⁷−6.90 × 10⁻⁵ M and can be attributed to an adsorption-controlled process with an irreversible reduction. Without using moxifloxacin, the polarographic determination of 2.50 × 10⁻⁶ M Co(II) is impossible under the given conditions due to very poor sensitivity at −1.38 V. The proposed method showed good precision and accuracy with a relative standard deviation of 3.01% and relative error of +6.40% for the determination of 2.50 × 10⁻⁶ M Co(II) next to 5.0 × 10⁻⁶ M of Zn(II), Ni(II), and Cd(II). The accuracy of the method was also checked by the determination of Co(II) spiked with tap water and certified sea water, and the percentage recoveries were 97.5 and 96.7%, respectively (n = 4 at 95% confidence interval). The text was submitted by the authors in English.     

Etude des possibilites de dosage du lithium par activation au moyen de protons et de deutons de moyenne energie

The determination of lithium by measuring⁷Be, produced by proton or deuteron activation, has been studied. The extent of interference from boron or beryllium, which also form⁷Be, was measured. The calculated sensitivity limits when activating for one hour with 10μA beams of 14 MeV protons or 25 MeV deuterons are, for lithium, 1·10⁻¹ and 2.5·10⁻² ppm and for boron, 2·10⁻¹ and 1·10⁻¹ ppm, respectively.      

Rapid photometric determination of neptunium with xylenol orange after extraction with Aliquat-336

A rapid method based on the extraction of neptunium(IV) by Aliquat-336 followed by its direct photometric determination in the organic phase employing xylenol orange is reported. Optinum conditions have been established for the extraction and determination of as little as 0.4 ppm of Np. The molar absorptivity of the red-coloured neptunium complex at 535 nm is 49535±361 1·mol⁻¹·cm⁻¹. Unlike the well-known absorptimetric method for estimating NP(IV) with Arsenazo III, this method tolerates many-fold excesses of fluoride, nitrite, nitrate, phosphote, oxalate as well as UO ₂ ²⁺ , Pu⁴⁺, Zr⁴⁺, etc., which are some of the major contaminants associated with neptunium during its reprocessing.     

A series of trinuclear sandwich-like cyanide-bridged iron(III)-manganese(II) complexes: synthesis,crystal structures,and magnetic properties

Four pyridinecarboxamide iron dicyanide building blocks and one Mn(III) compound have been employed to assemble cyanide-bridged heterometallic complexes, resulting in a series of trinuclear cyanide-bridged Fe^III–Mn^II complexes: {[Mn(DMF)₂ (MeOH)₂][Fe(bpb)(CN)₂]₂}·2DMF (1), {[Mn(MeOH)₄][Fe(bpmb)(CN)₂]₂}·2MeOH·2H₂O (2), {[Mn(MeOH)₄][Fe(bpdmb)(CN)₂]₂}·2MeOH·2H₂O (3) and {[Mn(MeOH)₄][Fe(bpClb)(CN)₂]₂}·4MeOH (4) (bpb²⁻ = 1,2-bis(pyridine-2-carboxamido)benzenate, bpmb²⁻ = 1,2-bis(pyridine-2-carboxamido)-4-methyl-benzenate, bpdmb²⁻ = 1,2-bis(pyridine-2-carboxamido)-4,5-dimethyl-benzenate, bpClb²⁻ = 1,2-bis(pyridine-2-carboxamido)-4-chloro-benzenate). Single-crystal X-ray diffraction analysis shows their similar sandwich-like structures, in which the two cyanide-containing building blocks act as monodentate ligands through one of their two cyanide groups to coordinate the Mn(II) center. Investigation of the magnetic properties of these complexes reveals antiferromagnetic coupling between the neighboring Fe(III) and Mn(II) centers through the bridging cyanide group. A best fit to the magnetic susceptibilities of complexes 1 and 3 gave the magnetic coupling constants J = −1.59(2) and −1.32(4) cm⁻¹, respectively.     

Construction of different types of ion-selective electrodes and validation of direct potentiometric determination of phenytoin sodium

The construction and performance characteristics of phenytoin sodium selective electrodes are detailed. Two types of electrodes: plastic membrane I and coated wire II, were constructed based on the incorporation of phenytoin sodium with tungstosilicic acid. The influence of membrane composition, kind of plasticizer, pH of the test solution, soaking time and the electrodes’ foreign ions were investigated. The electrodes showed a Nernstian response with a mean calibration graph slope of 30.9±0.1 and 28.9±0.1 mV decade⁻¹ at 25°C for electrode I and II respectively, over a phenytoin sodium concentration range of 5×10⁻³−5×10⁻⁶ M and 1×10⁻³−1×10⁻⁶ M with a detection limit 1.3×10⁻⁶ M and 2.5×10⁻⁷ M for electrode I and II, respectively. The electrodes gave average selective precision and were usable within the pH range 6–10. Interference studies from common cations, alkaloids, sugars, amino acids and drug excipients are reported. The results obtained by the proposed electrodes were also applied successfully for the determination of the drug in pharmaceutical preparations and biological fluids.     

A bimetallic cyano-bridged complex based on nickel(II) and pentacyanidonitrosylferrate(II) precursors: characterization, crystal structure, and magnetic properties

A heterobimetallic cyano-bridged 1D coordination polymer of the composition [Ni(baepn)(μ-NC)Fe(CN)₃(NO)(μ-CN)]_n·3H₂O has been synthesized by the reaction of nickel(II) nitrate hexahydrate, baepn (baepn = N, N′-bis(2-aminoethyl)-1,3-propanediamine), and sodium nitroprusside dihydrate in a methanol–water mixture. The complex was characterized by physicochemical and spectroscopic methods. The crystal structure was established by single-crystal X-ray diffraction analysis. It reveals cyano-bridged heterometallic chains consisting of alternating arrays of Ni(II) and Fe(II) atoms, both being embedded in distorted octahedral environments. Low-temperature susceptibility measurements show the presence of weak antiferromagnetic exchange interactions between paramagnetic Ni(II) centers (J = −0.46 cm⁻¹) through long diamagnetic [Fe(CN)₅(NO)]²⁻ bridges. Spin state of the iron atom was established by ⁵⁷Fe M?ssbauer spectroscopy.     

Development of reliable analytical method for extraction and separation of thorium(IV) by Cyanex 272 in kerosene

A simple and selective spectrophotometric method has been developed for the extraction and separation of thorium(IV) from sodium salicylate media using Cyanex 272 in kerosene. Thorium(IV) was quantitatively extracted by 5 × 10⁻⁴ M Cyanex 272 in kerosene from 1 × 10⁻⁵M sodium salicylate medium. The extracted thorium(IV) was stripped out quantitatively from the organic phase with 4.0 M hydrochloric acid and determined spectrophotometrically with arsenazo(III) at 620 nm. The effect of concentrations of sodium salicylate, extractant, diluents, metal ion and strippants has been studied. Separation of thorium(IV) from other elements was achieved from binary as well as multicomponent mixtures such as uranium(VI), strontium(II), rubidium(I), cesium(I), potassium(I), Sodium(I), lithium(I), lead(II), barium(II), beryllium(II) etc. Using this method separation and determination of thorium(IV) in geological and real samples has been carried out. The method is simple, rapid and selective with good reproducibility (approximately ±2%).     

Estimation of performance parameters of a frontal variant of optoacoustic determination with a model system

Using a model system, the applicability of the frontal configuration of optoacoustic spectroscopy in analytical practice is shown. An optoacoustic cell made using layered-prism geometry was designed and tested; it ensures operation with a layer thickness of 20–100 μm and sample volumes of 50–100 μl. Conditions are proposed for determining iron(II) in the form of tris(1,10-phenanthrolinate) with the detection limit of 3 × 10⁻⁷ M, which is less that the detection limit under similar induction conditions and for the same determination procedure using thermal-lens spectrometry (4 × 10⁻⁷ M). The determination has high reproducibility (relative standard deviation for 10⁻⁶ M is 0.005) and expressivity (1 min per sample detection).