Recovery of atrazine, bromacil, chlorpyrifos, and metolachlor from water samples after concentration on solid-phase extraction disks: interlaboratory study

An interlaboratory comparison was conducted in 1997 and 1998 to examine the feasibility of using C18 solid-phase extraction disks (Empore) to simultaneously determine the herbicides atrazine, bromacil, and metolachlor and the insecticide chlorpyrifos in water samples. A common fortification source and sample processing procedure were used to minimize variation in initial concentrations and operator inconsistencies. The protocol consisted of paired laboratories in different locations coordinating their activities and shipping fortified water samples (deionized or local surface water) or Empore disks on which the pesticides had been retained and then quantitating the analytes by a variety of gas chromatographic methods. Average recoveries from all laboratories were >80% for atrazine, bromacil, and metolachlor, and >70% for chlorpyrifos. Detection of bromacil was unachievable at some locations because of chromatographic problems. Shipping samples between cooperating laboratories did not affect the recovery of atrazine, chlorpyrifos, or metolachlor in either matrix. Recoveries tended to be higher from disks shipped to cooperating laboratories compared with those from fortified water. Shipping disks eliminated many problems associated with the shipment of water samples, such as bottle breakage, higher shipping cost, and possible pesticide degradation. Recoveries of bromacil and metolachlor were lower from fortified surface water samples than from fortified deionized water samples. This collaborative research demonstrated that pesticides in water samples can be concentrated on solid-phase extraction disks at one location and quantitated under diverse analytical conditions at another location. The extraction efficiencies of the disks were comparable with or better than the recoveries obtained from the shipped water samples, and the problems associated with shipping water samples were eliminated by using the disks.     

Multiresidue determination of pesticides in drinking and related waters by gas chromatography/mass spectrometry after solid-phase extraction: interlaboratory study

As part of a project funded by the European Commission (EC) for the development and evaluation of multiresidue methods for analysis of drinking and related waters, 15 European laboratories evaluated a method using styrene-divinylbenzene co-polymer solid-phase extraction followed by gas chromatography/mass spectrometry. The main aim of the study was to evaluate whether the method meets the requirements of EC Directive 98/83 in terms of accuracy, precision, and detection limit for 22 pesticides according to the following requirements: limit of detection, < or = 0.025 microg/L; accuracy, expressed as recovery between 75 and 125%; and precision, expressed as repeatability relative standard deviation of the method of < 12.5% and as reproducibility relative standard deviation of the method of < 25%. Analyses for unknown concentrations were performed with fortified commercial bottled and tap waters. All laboratories were able to achieve detection limits of 0.01 microg/L for all pesticides except dimethoate and desisopropylatrazine (0.02 microg/L). The criteria for repeatability were met for all compounds except trifluralin, dimethoate, and lindane in bottled water and chlorpyrifos, dimethoate, and lindane in tap water. The criteria for reproducibility were met for all compounds except trifluralin, dimethoate, and lindane in bottled water and pendimethalin, chlorpyrifos, dimethoate, terbutryn, and lindane in tap water. In terms of accuracy, the method meets the requirements for all pesticides in both matrixes, except for lindane in bottled water and lindane and chlorpyrifos in tap water.     

Multiresidue determination of pesticides in drinking and related waters by solid-phase extraction and liquid chromatography with ultraviolet detection: interlaboratory study

As part of a project funded by the European Commission (EC) for the development and evaluation of multiresidue methods for analysis of drinking and related waters, 17 European laboratories evaluated a method using styrene-divinylbenzene copolymer solid-phase extraction followed by liquid chromatography with diode array detection. The main aim of the study was to evaluate whether the method meets the requirements of EC Drinking Water Directive 98/83 in terms of accuracy, precision, and detection limit for 21 pesticides according to the following requirements: limit of detection, < or =0.025 microg/L; accuracy expressed as recovery, between 75 and 125%; and precision expressed as repeatability relative standard deviation of the method, <12.5%, and as reproducibility relative standard deviation of the method, <25%. Analyses for unknown concentrations were performed with commercial bottled and tap waters. All laboratories were able to achieve detection limits of 0.01 microg/L for all pesticides except pirimicarb (0.02 microg/L). The criteria for repeatability were met for all compounds. Terbutryn in bottled water and carbendazim in tap water did not meet the criteria for reproducibility. In terms of accuracy, the method met the requirements for all pesticides in both matrixes, except for metamitron. However, several compounds (linuron, terbutryn, propazine, metobromuron, and isoproturon) showed recoveries slightly below 75%.     

Screening of pesticides via solid-phase extraction and gas chromatography

This work describes an analytical method for the screening of pesticide residues in water. The developed method identifies and quantitates a variety of pesticides in water samples such as organochlorine, organophosphate, chloronitrile, phthalimide, dicarboximide, and triazine. The analytical technique employed for the extraction and cleanup step involves solid-phase extraction with C-18 cartridges. The identification and determination of concentration is carried out with gas chromatography. Two columns of different polarity and two specific detectors are used. An electron capture detector is used for organochrolorine, and a thermoinic detector is used for organonitrogen and organophosphate. The good resolution achieved with the temperature program and the combination of columns is shown in the chromatograms obtained. The limits of detection, percent recovery, and their respective standard deviations are determined for each product. According to the results obtained, this method permits monitoring of the pesticides mentioned, many of which are moderately to highly toxic to aquatic organisms.     

Multiresidue method for the gas chromatographic determination of pesticides in honey after solid-phase extraction cleanup

A new multiresidue method is described for the determination of pesticides in honey. The method involves dissolution of the honey in a methanol-water mixture, followed by solid-phase extraction cleanup and gas chromatographic determination. Twenty-six pesticides used on flowering field crops, on flowering fruit and vegetables, or as acaricides to control Varroa jacobsoni in beehives are determined by the method. Recoveries from honey, spiked at 0.02-1.6 mg/kg, ranged from 85 to 127% with a relative standard deviation (RSD) of 2-16%, except for the RSD of 27% for captan at 0.05 mg/kg.     

Evaluation of carbon nanocones/disks as sorbent material for solid-phase extraction

The potential of carbon nanocones/disks as sorbent material in solid-phase extraction (SPE) procedures has been evaluated. For this aim, a model analytical problem, the determination of chlorophenols in water samples, was selected. An accurately weighed amount of 20 mg of purified carbon nanocones/disks was packed in 3 mL commercial SPE cartridges. Once conditioned, up to 8 mL of water samples can be preconcentrated without analyte losses. The chlorophenols were eluted by using 200 μL of hexane. Aliquots of 2 μL of the organic extract were injected in the gas chromatograph–mass spectrometer for separation and quantification. The purification of the commercial nanocones/disks to reduce the presence of amorphous carbon has been successfully achieved by heating the carbon nanocones/disks at 450 °C for 20 min. Detection limits of chlorophenols were in the range 0.3–8 ng mL⁻¹ by using 2 mL of sample. Moreover, excellent average recovery values (98.8–100.9%) have been obtained after the analysis of water samples from different nature. Finally, the performance of the carbon nanocones/disks as sorbent material has been compared with that of multiwalled carbon nanotubes, providing the former better results under the experimental conditions assayed.     

Stripping voltammetric analysis of organophosphate pesticides based on solid-phase extraction at zirconia nanoparticles modified electrode

A sensitive electrochemical stripping voltammetric method for analyzing organophosphate (OP) compounds was developed based on solid-phase extraction (SPE) at zirconia (ZrO₂) nanoparticles modified electrode. ZrO₂ nanoparticles were proved as a new sorbent for SPE of OP pesticides. Because of the strong affinity of ZrO₂ for the phosphoric group, nitroaromatic OPs can strongly bind to the ZrO₂ nanoparticle surface. The combination of SPE with square-wave voltammetry (SWV) provided a fast, sensitive, and selective electrochemical method for nitroaromatic OP compounds using methyl parathion (MP) as a model. The stripping response was highly linear over the MP range of 0.003–2.0 μg/mL, with a detection limit of 0.001 μg/mL. The fast extraction ability of ZrO₂ nanoparticles makes it promising sorbent for various solid-phase extractions.     

Capillary electrophoresis for analyzing pesticides in fruits and vegetables using solid-phase extraction and stir-bar sorptive extraction

Two procedures based on solid-phase extraction (SPE) and stir-bar sorptive extraction (SBSE) in combination with micellar electrokinetic chromatography (MEKC)--diode array detection (DAD) were compared for the simultaneous extraction of acrinathrin, bitertanol, cyproconazole, fludioxonil, flutriafol, myclobutanil, pyriproxyfen, and tebuconazole in lettuce, tomato, grape, and strawberry. Selectivity and resolution of the MEKC procedure were studied changing the pH and the molarity of the buffer, the type and the concentration of surfactant, and the methanol content in the mobile phase. A buffer consisting of 6 mM sodium tetraborate decahydrate with 75 mM of cholic acid sodium solution (pH 9.2) gave the best results. Linearity, extraction efficiencies and limits of quantitation (LOQs) of both extraction methods were compared. The recoveries obtained by SPE ranged from 40 to 106% with relative standard deviations (R.S.D.s) from 10 to 19% whereas by the SBSE method, the recoveries were 12-47% and the R.S.D.s 3-17%. The LOQs were much better by SPE (0.2-0.5 mg kg(-1) depending on the processed sample amount) than those obtained by SBSE (1 mg kg(-1) for each compound). Advantages and disadvantages of both procedures are also discussed. As SPE is more robust, rapid, and sensitive than SBSE, its application in combination with MEKC is recommended because provided LOQs below the MRLs established, which is not always attained by SBSE.     

Retention behavior and solvent optimization of organochlorine pesticides in solid-phase extraction

Summary Plots of capacity factor and retention time vs. elution solvent composition were proved to be useful to interpret the retention behavior of Kepone and its metabolites in a reversed-phase solid-phase extraction and to optimize the elution solvent. The percent recovery of Kepone was largely improved when the solvent was optimized. The standard deviations of the results of extractions were also improved upon the optimization of the solvent.     

The stability of selected herbicides preconcentrated from estuarine river waters on solid-phase extraction disks

Summary The stability of atrazine, simazine, alachlor, metolachlor, and deethylatrazine on C₁₈ Empore disks has been determined. Estuarine water (100 mL) spiked at 3 g L^–1 with the target pesticide mixture was preconcentrated on the disks; the disks were then stored at –20°C, 4°C, and at room temperature for periods up to three months and were analyzed by gas chromatography with nitrogen-phosphorus detection. Complete recovery was observed after storage at –20°C throughout the period of the study. Losses up to maximum of 10% were observed after storage at 4°C. Higher losses (up to 24% for alachlor) occurred only at room temperature; the coefficient of variation for these determinations (8–11%) was also higher than that for the others (3–5%). The stability of the pesticides was dependent on the water matrix, on storage temperature, and on properties such as vapor pressure and water solubility.     

Interlaboratory comparison of pesticide recovery from water using solid-phase extraction disks and gas chromatography

An interlaboratory study was conducted to assess the suitability of C18 solid-phase extraction disks to retain and ship different pesticides from water samples. Surface and deionized water samples were fortified with various pesticides and extracted using C18 disks. Pesticides were eluted from disks and analyzed in-house, or disks were sent to another laboratory where they were eluted and analyzed. Along with the disks, a standard pesticide solution in methanol was also shipped to be used for fortification, extraction, and analysis. The highest recovery from deionized or surface water using shipped disks was obtained for cyanazine (>97%), followed by metalaxyl (>96%), and atrazine (>92%). Although <40% of the bifenthrin, chlorpyrifos, and chlorothalonil fortified in surface water was recovered from shipped disks, recoveries from deionized water were >70%. From in-house eluted disks, bifenthrin and chlorpyrifos were recovered at 118 and 105%, whereas chlorothalonil showed 71% recovery, indicating that poor recovery from surface water was due to loss during shipping rather than low retention by the C18 disks. There was no consistent relationship between recovery from C18 disk and physicochemical properties for the pesticides included in this study. For most of the 13 pesticides tested, there were no differences in recovery between in-house extracted disks and shipped disks, indicating the suitability of disks to concentrate and transport pesticides extracted from water samples.     

New materials for solid-phase extraction and multiclass high-performance liquid chromatographic analysis of pesticides in grapes

Sample preparation procedures which included the use of new aminopropyl (NH2) and octadecyl (C18) solid-phase extraction (SPE) sorbents are proposed for the simultaneous multiclass determination of the fungicide benomyl and of the herbicides tebuthiuron, diuron, simazine, atrazine, and ametryn in grapes, using single wavelength high-performance liquid chromatography. Sorbent preparation uses a fast, easy, and effective procedure to obtain silica-based materials, made by depositing polysiloxanes on a silica support followed by thermal immobilization. Recovery results of the compounds, after elution from the SPE cartridges, indicate that the most efficient system employed silica loaded with 40% of an aminofunctional polydimethylsiloxane as sorbent, using dichloromethane:methanol (95:5, v/v) as eluent. Method validation, carried out in agreement with International Conference on Harmonization directives, was performed at three fortification levels (100, 200, and 1000 microg kg(-1)). Limits of detection and quantification show that the method developed can be used to detect the pesticides at concentrations below the maximum residue levels established by Codex Alimentarius, the US Environmental Protection Agency, the European Union, and Brazilian legislation.     

Poly(methyloctylsiloxane) immobilized on silica as a sorbent for solid-phase extraction of some pesticides

A laboratory-made sorbent for solid-phase extraction (SPE) was obtained by thermal immobilization of poly(methyloctylsiloxane) (PMOS) onto silica. Cartridges packed with the new sorbent were used for the simultaneous determination of imazethapyr, nicosulfuron, diuron, linuron and chlorimuron-ethyl in water. These pesticides were separated and quantified using high-performance liquid chromatography with diode array detection (HPLC-DAD). The recoveries achieved with the laboratory-made PMOS cartridges were compared with those of some commercially available silica-based and polymer-based cartridges having C18, C8 and NH(2) pendant groups. Method validation using the laboratory-made sorbent was performed for the five pesticides at three fortifications levels (1x, 2x and 10x the limit of quantification of each pesticide). The laboratory-made PMOS cartridge has low cost preparation and showed good recoveries (72-111%) for all pesticides. Repeatability and intermediate precision were lower than 15%. Its performance was similar or even better, in some cases, than those of the commercial cartridges.     

Comparison of solid-phase extraction and micro-solid-phase extraction for liquid chromatography/mass spectrometry analysis of pesticides in water samples

Our recent on-line solid-phase extraction (SPE) device for micro-liquid chromatography, known as micro-solid-phase extraction (microSPE), was compared with traditional SPE for the analysis, from aqueous samples, of 4 pesticides belonging to different classes. Two different kinds of adsorbents, C18 and graphitized carbon black, were tested. A 2-stage ion trap mass spectrometer, equipped with homemade microflow electrospray ion (ESI) source, was used. Detection limits with a signal-to-noise ratio of 3:1 for both extraction methods were in the range of 0.1 microg/L for all compounds. However, better recoveries were obtained when microSPE traps were used.     

Phenylboronic acid-functionalized cross-linked chitosan magnetic adsorbents for the magnetic solid-phase extraction of benzoylurea pesticides

In this study, a 4-formylphenylboronic acid-modified cross-linked chitosan magnetic nanoparticle (FPBA@CCHS@Fe₃O₄) was fabricated. The synthesized material was utilized as the magnetic solid-phase extraction adsorbent for the enrichment of six benzoylurea pesticides. In addition to B-N coordination, FPBA@CCHS@Fe₃O₄ interacts with benzoylureas through hydrogen bonds and π-π stacking interaction on account of rich active groups (amino and hydroxyl) and aromatic rings in structure. Compared to traditional extraction methods, less adsorbent (20 mg) and reduced extraction time (3 min) were achieved. The adsorbent also exhibited good reusability (no less than 10 times). Coupled with a high-performance liquid chromatography–diode array detector, satisfactory recoveries (89.1–103.9%) and an acceptable limit of detection (0.2–0.7 μg/L) were obtained. Under optimized conditions, the established method was successfully applied to the tea infusion samples from six major tea categories with acceptable recoveries ranging from 76.8 to 110%, indicating its application potential for the quantitative detection of pesticides in complex matrices.     

Simultaneous extraction and determination of various pesticides in environmental waters

A simple and rapid method was developed for the simultaneous analysis of nine different pesticides in water samples by gas chromatography with mass spectrometry. A number of parameters that may affect the recovery of pesticides, such as the type of solid‐phase extraction cartridge, eluting solvent in single or combination and their volumes, and water pH value were investigated. It showed that three solid‐phase extraction cartridges (Strata‐X, Oasis HLB, and ENVI‐18) produced the greatest recovery while ethyl acetate/dichloromethane/acetone (45:10:45, 12 mL) followed by dichloromethane (6 mL) was efficient in eluting target pesticides from solid‐phase extraction cartridges. Different water pH values (4–9) did not show a significant effect on the pesticides recovery. The optimized method was verified by performing spiking experiments with a series of concentrations (0.002–10 μg/L) in waters, with good linearity, recovery, and reproducibility for most compounds. The limit of detection and limit of quantification of this optimized method were 0.01–2.01 and 0.02–6.71 ng/L, respectively, much lower than the European Union environmental quality standard for the pesticides (0.1 μg/L) in waters. The proposed method was further validated by participation in an interlaboratory trial. It was then subsequently applied to river waters from north‐east Scotland, UK, for the determination of the target pesticides.     

Determination of triazines and organophosphorus pesticides in water samples using solid-phase extraction.

Octadecyl (C18)-bonded porous silica was evaluated for the extraction of triazine and organophosphorus pesticides from natural water. The extraction results showed an effective performance when 11 of water was passed through small glass columns containing 500 mg of 50-100-microns C18 bonded porous silica. The adsorbed compounds were removed with ethyl acetate, evaporated to 200 microliters and determined by gas chromatography. The overall average recoveries were greater than 85% except for dimethoate and trichlorfon. Application of this procedure to the analysis of natural water samples gave results that agree well with those obtained by solvent extraction methods.     

Multiresidue determination of pesticides in juice by solid-phase extraction and gas chromatography-mass spectrometry

A multiresidue method based on solid-phase extraction was developed for the simultaneous determination of 50 pesticides in commercial juices. The extraction procedure was carried out in C₁₈ columns preconditioned with acetonitrile and water. The subsequent elution of pesticides was performed with a mixture of hexane-ethyl acetate (1:1, v/v) prior to the determination by gas chromatography with electron impact mass spectrometric detection in the selected ion monitoring mode (GC-MS-SIM), using one target and two qualifier ions. Standards were prepared spiking blank juice samples to counteract the observed matrix effect. Average recoveries for all the pesticides studied were higher than 91% with relative standard deviations lower than 9% in the concentration range of 0.02-0.1 μg/mL and the detection limits achieved ranged from 0.1 to 4.6 μg/L. The proposed method was applied to the analysis of these compounds in commercial juices and diazinon, ethion and procymidone were the pesticides encountered, although the levels found were very low.     

Analysis of pesticides in soy milk combining solid-phase extraction and capillary electrophoresis-mass spectrometry

In this work, the determination of a group of triazolopyrimidine sulfoanilide herbicides (cloransulam-methyl, metosulam, flumetsulam, florasulam, and diclosulam) in soy milk by capillary electrophoresis-mass spectrometry (CE-MS) is presented. The main electrospray interface (ESI) parameters (nebulizer pressure, dry gas flow rate, dry gas temperature, and composition of the sheath liquid) are optimized using a central composite design. To increase the sensitivity of the CE-MS method, an off-line sample preconcentration procedure based on solid-phase extraction (SPE) is combined with an on-line stacking procedure (i.e. normal stacking mode, NSM). Samples could be injected for up to 100 s, providing limits of detection (LODs) down to 74 microg/L, i.e., at the low ppb level, with relative standard deviation values (RSD,%) between 3.8% and 6.4% for peak areas on the same day, and between 6.5% and 8.1% on three different days. The usefulness of the optimized SPE-NSM-CE-MS procedure is demonstrated through the sensitive quantification of the selected pesticides in soy milk samples.