Role of gallium wetting layer in high-quality ZnO growth on sapphire (0001) substrates

ZnO is a wide direct bandgap (Eg=3.37 eV at room temperature) II-VI compound semiconductor of wurtzite structure (a = 3.249 ? c = 5.207 ?. Compared to GaN and ZnS, ZnO has a larger exciton binding energy, ~60 meV (cf. ~25 meV for GaN and ~40 meV for ZnS), which is advantageous to realizing low-threshold excitonic lasers. Since optically pumped UV lasing of ZnO at room temperature was reported in 1997[1], much attention has been paid to the crystal quality improvement and p-type conduc…     

Low-temperature growth of single-crystalline ZnO tubes on sapphire(0001) substrates

Single-crystalline ZnO tubes were grown on sapphire(0001) substrates by metalorganic chemical vapor deposition at 400 °C. The growth temperature was much lower than that (900–1100 °C) used in previous reports. The tubes were grown along the substrate normal and were characterized by hexagon-shaped cross sections. All of the tubes possessed the same epitaxial relationships with respect to the substrate. Growth pressure was found to play an important role in the formation of ZnO tubes. PACS 61.46.+w; 78.67.-n; 81.15.Gh     

Polarity control and residual strain in ZnO epilayers grown by molecular beam epitaxy on (0001) GaN/sapphire

We report on the polarity control of ZnO grown by plasma assisted molecular beam epitaxy on Ga polar (0001) GaN/sapphire templates simply via the oxygen‐to‐Zn (VI/II) ratio during the growth of a thin nucleation layer at 300 °C. Following Zn pre‐exposure, the ZnO layers nucleated with low VI/II ratios (<1.5) exhibited Zn‐polarity. Those nucleated with VI/II ratios above 1.5, exhibited O‐polarity. Supported by scanning transmission electron microscopic imaging, we have unequivocally demonstrated that polarity inversion takes place without formation of any vertical inversion domains and within one monolayer of presumably non‐stoichiometric GaO_x formed at the ZnO/GaN interface. A direct correlation between polarity and strain sign of ZnO layers has been found. The Zn‐polar ZnO layers were under tensile biaxial strain, whereas the O‐polar material exhibited compressive strain. Moreover, the amount of residual strain varied linearly with VI/II ratio used during the low‐temperature nucleation layer growth. Strain control with VI/II ratio has been explained by the potential formation of Zn interstitials.     

Atomic layer molecular beam epitaxy growth of InAs on GaAs substrates

InAs layers with thickness ranging from 0.1 to 2.5 m have been grown directly on highly mismatched (7.4%) (001) GaAs substrates by atomic layer molecular beam epitaxy (ALMBE). This growth method, based on the modulated deposition of one or both component species, provides InAs layers with excellent flat morphology, independently of the total thickness. A detailed study of the evolution of the electron diffraction (RHEED) pattern indicates that a complete decoupling between the InAs epitaxial layer and the GaAs substrate is reached in less that 10 monolayers. Evidence is obtained that layer-by-layer nucleation takes place from the beginning of the growth.     

Optical properties and structural characteristics of ZnO thin films grown on a-plane sapphire substrates by plasma-assisted molecular beam epitaxy

We investigated structural and optical properties of ZnO thin films grown on (112?0) a-plane sapphire substrates using plasma-assisted molecular beam epitaxy. Negligible biaxial stress in ZnO thin films is due to the use of (112?0) a-plane sapphire substrates and slow substrate cooling. The 14 K photoluminescence spectrum shows a blueshift of energy positions compared with ZnO single crystal. A donor with binding energy of 43 meV and an acceptor with binding energy of ～170 meV are identified by well-resolved photoluminescence spectra. A characteristic emission band at 3.320 eV (so-called A-line) is studied. Based on analysis from photoluminescence spectra, the origin of the A-line, it seems, is more likely an (e, A°) transition, in which defect behaves as an acceptor. The room-temperature photoluminescence is dominated by the FX at 3.307 eV, which is an indication of strongly reduced defect density in ZnO thin films.     

Growth of high-quality ZnO thin films on (11\bar{2}0) a-plane sapphire substrates by plasma-assisted molecular beam epitaxy

High-quality ZnO thin films were grown on a-plane sapphire substrates by plasma-assisted molecular beam epitaxy. X-ray diffraction and transmission electron microscopy reveal that the ZnO films have high structural quality and an atomically sharp ZnO/Al₂O₃ interface. The full width at half maximum values of the 0002 and $30\bar{3}2$ ZnO ω-rocking curves are 467.8 and 813.5 arc sec for a 600 nm thick ZnO film. A screw dislocation density of 4.35×10⁸ cm^?2 and an edge dislocation density of 3.38×10⁹ cm^?2 are estimated by X-ray diffraction. The surface of the ZnO epilayers contains hexagonal pits, which can be observed in the Zn-polar ZnO. The films have a resistivity of 0.119 Ω?cm, an electron concentration of 6.85×10¹⁷ cm^?3, and a mobility of 76.5 cm²?V^?1?s^?1 at room temperature. Low temperature photoluminescence measurements show good optical properties comparable to ZnO single crystals.     

Graphene films grown on sapphire substrates via solid source molecular beam epitaxy

A method for growing graphene on a sapphire substrate by depositing an SiC buffer layer and then annealing at high temperature in solid source molecular beam epitaxy (SSMBE) equipment was presented. The structural and electronic properties of the samples were characterized by reflection high energy diffraction (RHEED), X-ray diffraction Φ scans, Raman spectroscopy, and near edge X-ray absorption fine structure (NEXAFS) spectroscopy. The results of the RHEED and Φ scan, as well as the Raman spectra, showed that an epitaxial hexagonal α-SiC layer was grown on the sapphire substrate. The results of the Raman and NEXAFS spectra revealed that the graphene films with the AB Bernal stacking structure were formed on the sapphire substrate after annealing. The layer number of the graphene was between four and five, and the thickness of the unreacted SiC layer was about 1--1.5 nm.     

Epitaxial growth of GaN on Si (100)/sapphire (0001) using RF plasma-assisted ionized source beam epitaxy

A new approach to epitaxial GaN growth utilizing radiofrequency plasma-assisted ionized source beam epitaxy (PAISBE) is described. To facilitate the reaction between Ga and atomic nitrogen, the Ga beam was partially ionized and accelerated. The reactive atomic nitrogen flux was obtained from an RF discharge nitrogen plasma with controllable power and frequency. A grid was placed at the exit end of the plasma tube to prevent N _inf2 ^up+ from hitting the substrate. The growth parameters were chosen to systematically investigate the effects of Ga-beam ionization and grid bias. The crystal quality of the PAISBE-grown GaN was analysed by RHEED and x-ray diffraction. The FWHM of a 0.4-m-thick GaN epilayer grown with ionized Ga beam and RF nitrogen plasma with 140W power was measured to be 25 min at (0002) diffraction peak. This and other preliminary data from the present study indicate that PAISBE is a promising technique for GaN growth.     

Growth of wide band gap wurtzite ZnMgO layers on (0001) Al2O3 by radical-source molecular beam epitaxy

Wurtzite structure ZnMgO layers have been grown using radical-source molecular beam epitaxy on high-quality ZnO buffer layers grown on (0001) sapphire substrates. The thickness of the ZnO buffer layers is 300 nm, with full width at half maxim of the HR-XRD (0002) rocking curves as low as 25 arcsec. In-situ Reflection High-Energy Electron Diffraction (RHEED) was employed for the optimization of the ZnMgO growth. RHEED and X-Ray Diffractometry measurements did not reveal any phase change from the wurzite structure to the rocksalt structure. The C-lattice parameter of Zn_1−xMg_xO films decreased from 5.209 to 5.176 Å with increasing x to 0.2. The surface morphology of the samples was studied with atomic force microscopy. The root mean square roughness values of 200 nm thick ZnMgO (x=0.2) was less than 1 nm. The main photoluminescence peak of Zn_1−xMg_xO shifted to as high as 3.77 eV owing to the increasing Mg composition of up to x=0.2.     

Surface preparation effect of GaAs(110) substrates on the ZnSe epitaxial layer grown by molecular beam epitaxy

The effect of the surface preparation of the GaAs(110) substrate on the ZnSe epitaxial layer grown by molecular beam epitaxy (MBE) was investigated by means of etch-pit density (EPD) measurements, surface morphology observation, and reflection high-energy electron diffraction (RHEED) analysis. The ZnSe epitaxial layer grown on a GaAs(110) surface prepared by cleaving the (001)-oriented wafer in ultrahigh vacuum (UHV) showed about 5×10⁴ cm^-2 of EPD. This value is much lower than that observed from both the samples grown on the mechanically polished surface with and without a GaAs buffer layer. Due to the non-stoichiometric surface after thermal evaporation of the surface oxide, three-dimensional growth can easily occur on the mechanically polished GaAs(110) substrate. These results suggest that the stoichiometric and atomically flat substrate surface is essential for the growth of low-defect ZnSe epitaxial layers on the GaAs(110) non-polar surface. Received: 21 August 1998 / Accepted: 19 October 1998 / Published online: 28 April 1999     

Si(001)衬底上分子束外延生长Ge0.975Sn0.025合金薄膜

使用低、高温两步法生长的高质量Ge薄膜作为缓冲层,在Si(001)衬底上采用分子束外延法生长出Ge_0.975Sn_0.025合金薄膜.X射线双晶衍射和卢瑟福背散射谱等测试结果表明,Ge_0.975Sn_0.025合金薄膜具有很好的晶体质量,并且没有发生Sn表面分凝.另外,Ge_0.975Sn_0.025合金薄膜在500 ℃下具有很好的热稳定性,有望在Si基光电器件中得到应用. 关键词： GeSn Ge 分子束外延 外延生长     

GaAs(001)衬底上分子束外延生长InNSb单晶薄膜

利用射频氮等离子辅助分子束外延(RF-MBE)技术在GaAs(001)衬底上生长稀氮 InNSb半导体薄膜,并通过原子力显微镜(AFM)、扫描电子显微镜(SEM)、X射线衍射仪(XRD)和拉曼散射光谱等测量手段对样品的微结构和N组分等进行了表征.结果显示样品有较好的晶体质量,N组分可高达0.84%(XRD的结果).本文还对样品的输运性质进行了表征,结果显示样品在室温下具有较低的载流子浓度和较高的迁移率.另外,初步研究表明在InSb中掺入N可导致其室温磁阻明显下降. 关键词： 分子束外延 稀氮半导体 X射线衍射 拉曼光谱     

AlGaN/GaN HEMTs grown on silicon (001) substrates by molecular beam epitaxy

We report the realization of an AlGaN/GaN HEMT on silicon (001) substrate with noticeably better transport and electrical characteristics than previously reported. The heterostructure has been grown by molecular beam epitaxy. The 2D electron gas formed at the AlGaN/GaN interface exhibits a sheet carrier density of 8×10¹² cm⁻² and a Hall mobility of 1800 cm²/V s at room temperature. High electron mobility transistors with a gate length of 4 μm have been processed and DC characteristics have been achieved. A maximum drain current of more than 500 mA/mm and a transconductance g_m of 120 mS/mm have been obtained. These results are promising and open the way for making efficient AlGaN/GaN HEMT devices on Si(001).     

Study of molecular beam epitaxy of cadmium telluride on sapphire

The effect of thermal treatment of (0001) sapphire substrates on the structure of cadmium telluride films grown by molecular beam epitaxy was investigated. The growth process was carried out on a laboratory facility equipped with a mass spectrometer and electron diffractometer. It was established that no annealing or annealing in vacuum (P < 0.13 Pa) results in the growth of polycrystalline CdTe films. Epitaxial CdTe films with a cubic structure of the sphalerite type oriented with the (111) plane parallel to the substrate grow on the substrates annealed in air at T > 1000°C. Electron diffraction patterns showed that they have a mosaic structure and contain twins with the 〈111〉 twinning axis. Atomic-force microscopic images revealed CdTe crystallites with lateral sizes of ∼50 nm arranged along the steps on the sapphire substrate surface. These results allowed the conclusion to be drawn that the growth of CdTe on sapphire substrates can occur by the formation of the three-dimensional nucleation centers according to the Volmer-Weber mechanism.     

斜切蓝宝石衬底MOCVD生长GaN薄膜的透射电镜研究

利用MOCVD技术在斜切角度为0.3°的c面蓝宝石衬底上生长了非故意掺杂 GaN 薄膜, 并采用透射电子显微镜对材料的质量和材料内部缺陷进行了分析. 研究发现斜切蓝宝石衬底上外延的GaN材料中,位错在距离衬底0.8 μm附近大量湮灭, 同时位错扎堆出现.基于上述现象, 提出了斜切衬底上GaN材料中位错的湮灭机制, 解释了斜切衬底能够提高GaN晶体质量的原因.     

Graphene growth on h-BN by molecular beam epitaxy

The growth of single layer graphene nanometer size domains by solid carbon source molecular beam epitaxy on hexagonal boron nitride (h-BN) flakes is demonstrated. Formation of single-layer graphene is clearly apparent in Raman spectra which display sharp optical phonon bands. Atomic-force microscope images and Raman maps reveal that the graphene grown depends on the surface morphology of the h-BN substrates. The growth is governed by the high mobility of the carbon atoms on the h-BN surface, in a manner that is consistent with van der Waals epitaxy. The successful growth of graphene layers depends on the substrate temperature, but is independent of the incident flux of carbon atoms.     

Atypical grain boundaries in ZnO layers deposited on sapphire by rf magnetron sputtering on (0001) sapphire

The crystalline quality of ZnO is investigated, in thin films prepared by RF magnetron sputtering on c-plane sapphire. The ZnO layers exhibit a columnar growth and the average column diameter depends on the deposition temperature. Along the [] zone axis of sapphire, the diffraction pattern exhibits two zone axis patterns; the central rows belong to the two zones, with the 0002n spots clearly underlined by the overlap. On each part, the two inner rows belong to the [] zone and the next two to the [] zone. Therefore, the two main epitaxial relationships in mismatched growth of wurtzite structures coexist in these layers, and adjacent columns are rotated, with respect to one other, by 90 around the [0001] direction. In cross section observations, the interface between two grains is abrupt, but it is not easy to determine its atomic structure. Observations in planar view show that although the long range rotation between grains is in agreement with the theoretical epitaxial relationships, the local angles oscillate between 27 and 32. This discrepancy is explained by the formation of grain boundaries which are found to follow the coincidence site lattice rules which make them settle into minimal energy configurations.     

Synthesis of single crystalline GaN nanoribbons on sapphire (0001) substrates

Single crystalline GaN nanoribbons were synthesized through nitriding Ga₂O₃ thin films deposited on sapphire (0001) substrates by radio frequency magnetron sputtering. The component and structure of nanoribbons were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX), transmission electron microscopy (TEM) and high-resolution transmission electron microscopy (HRTEM). The flat and smooth ribbon-like nanostructures are high quality single crystalline hexagonal wurtzite GaN. The thickness and width-to-thickness ratio of the grown GaN nanoribbons are in the range of 8-15 nm and ∼5-10, respectively.     

Quantum dots-templated growth of strain-relaxed GaN on a c-plane sapphire by radio-frequency molecular beam epitaxy

We investigated the quantum dots-templated growth of a(0001) GaN film on a c-plane sapphire substrate.The growth was carried out in a radio-frequency molecular beam epitaxy system.The enlargement and coalescence of grains on the GaN quantum dots template was observed in the atom force microscopy images,as well as the more ideal surface morphology of the GaN epitaxial film on the quantum dots template compared with the one on the AlN buffer.The Ga polarity was confirmed by the reflected high energy electron diffraction patterns and the Raman spectra.The significant strain relaxation in the quantum dots-templated GaN film was calculated based on the Raman spectra and the X-ray rocking curves.Meanwhile,the threading dislocation density in the quantum dots-templated film was estimated to be 7.1×107cm-2,which was significantly suppressed compared with that of the AlN-buffered GaN film.The roomtemperature Hall measurement showed an electron mobility of up to 1860cm2 /V·s in the two-dimensional electron gas at the interface of the Al 0.25Ga0.75 N/GaN heterojunction.