Adsorption of Ag on Si(1 0 0) surface

The chemisorption of one monolayer Ag atoms on an ideal Si(1 0 0) surface is studied by using the self-consistent tight-binding linear muffin-tin orbital method. The adsorption energies (E_ad) of different sites are calculated. It is found that the adsorbed Ag atoms are more favorable on C site (fourfold site) than on any other sites on Si(1 0 0) surface, the polar covalent bond is formed between Ag atom and surface Si atom, a Ag and Si mixed layer does not exist and does form an abrupt interface at the Ag–Si(1 0 0) interface. This is in agreement with the experiment results. The layer-projected density of states is calculated and compared with that of the clean surface. The charge transfer is also investigated. Comparing with the Au/Si(1 0 0) system, the interaction is weaker between Ag and Si than between Au and Si.     

Nitrogen nanobubbles and butane nanodroplets at Si(1 0 0)

Nanobubbles and nanodroplets were spontaneously formed at Si(1 0 0) in contact with nitrogen and butane saturated water, respectively. The topographic images obtained by tapping mode AFM were similar truncated nanospheres, but the phase images suggested that the nanobubbles were harder than the nanodroplets. The tip–sphere interactions showed the nanodroplets were much viscoelastic than the nanobubbles. The surface and three-phase contact line energies were estimated by analysis of the topographic images. The nanodroplet was stable, but the nanobubble was unstable in spite of the experimental long life. The two-dimensional spatial distribution indicated an attractive interaction between the nanodroplets, but no interaction was observed between the nanobubbles.     

Magnetic anisotropy of epitaxial Fe layers grown on Si(0 0 1)

The magnetic properties of epitaxial iron films up to 80 monolayers (ML) thickness grown on Si(0 0 1) by using a template technique were investigated by means of superconducting quantum interference device and magneto-optic Kerr effect techniques. The thinnest films investigated (∼3 ML) exhibit a composition close to Fe₃Si with a Curie temperature below room temperature (RT) and strong out-of-plane remanent magnetization that reflects the presence of a dominant second order surface anisotropy term. Thicker films (⩾4 ML) are ferromagnetic at RT with remanent magnetization in film-plane and a composition closer to pure Fe with typically 8–10% silicon content. When deposited at normal incidence such films show simple in-plane fourfold anisotropy without uniaxial contribution. The relevant fourth-order effective anisotropy constant K₄^eff was measured versus film thickness and found to change its sign near 18 ML. The origin of this remarkable behavior is investigated by means of a Néel model and mainly traced back to fourth-order surface anisotropy and magneto-elastic effects related to the large biaxial in-plane compressive strain up to 3.5% in the thinnest (⩽25 ML) films.     

Peculiarities of Al magic cluster self-assembly on Si(1 0 0) surface

Using scanning tunneling microscopy observations and density functional theory calculations, regularities of the Al magic cluster array self-assembly on Si(1 0 0) surface has been elucidated. While a single Al cluster occupies an area of 4a × 3a, an ordered Al-cluster array exhibits a 4 × 5 periodicity, as the clusters in the array are separated by the 4a × 2a “spacers”. The plausible structural model for the “spacer” was proposed in which the “spacer” is arranged as an ordinary 4a × 3a-Al cluster in which the central atomic row with the topmost Si atom is missing. Appearance of the “spacers” in the Al-cluster array was found to reduce formation energy of the array. Ability to incorporate the rows of Al-“spacers” into the completed 4 × 3 In-cluster array was demonstrated.     

Initial stage of CdTe on Si(1 0 0) grown by MBE

The initial stage of CdTe growth on silicon has been investigated using angle-resolved photoemission and scanning tunneling microscopy (STM). In order to study initial stage of CdTe on Si, we have desorbed CdTe by annealing at 600 °C so that only one monolayer of Te remains on the Si(1 0 0) substrate. Te/Si(1 0 0)2×1 superstructure has been observed by LEED. Photoemission spectra indicate that Te atoms bond with the Si dangling bond. Atomically resolved STM images reveal that the Te atoms form dimers. It is observed that buckling direction of Te-dimer changes and the dimmers are broken in the site of some dimmer rows. It can be explained that the large lattice mismatch cause the switching of the buckling direction and the breaking of Te-dimer resulted surface relaxation.     

Time-of-flight distributions of HD molecules abstracted at a Si(1 0 0) surface

We study the dynamics of D abstraction by 0.05 eV H atoms on a Si(1 0 0) surface. Time-of-flight (TOF) distributions of the abstracted HD molecules are measured using a quasi-random chopper/cross-correlation method. The measured TOF distribution is found to be broad and fast. The distribution is decomposed into two components being related to direct abstraction (ABS) and adsorption-induced-desorption (AID), which were revealed in the kinetics studies. The best curve fits yield mean kinetic energies of 1.15 ± 0.20 eV and 0.33 ± 0.05 eV for the ABS and AID components, respectively. Dynamics and kinetics of hydrogen abstraction at Si(1 0 0) surfaces are consistently understood.     

Growth and characterization of CoSi2 films on Si (1 0 0) substrates

In the present work, a special solid phase epitaxy method has been adapted for the preparation of CoSi₂ film. This method includes an epitaxial growth of Co films on Si (1 0 0) substrate, and in situ annealing of the Co/Si films in vacuum. It has been found that at the substrate temperature of 360°C, fcc cobalt film grows epitaxially on the Si (1 0 0) surface. The crystallographic orientation relations between fcc Co film and Si substrate determined from the electron diffraction result are: (0 0 1) Co//(0 0 1) Si, [1 0 0] Co//[1 1 0]Si. Upon annealing at temperatures range from 500 to 600°C, Co film reacts with Si substrate and transforms into CoSi₂. The CoSi₂ films prepared by this way are characterized by XTEM, XPS and AFM.     

Adsorption of molecular SiO2 on a clean Si(1 0 0) surface

We have investigated the adsorption of molecular (gaseous) SiO₂ on a clean Si(1 0 0) p(2 × 2) reconstructed surface using density functional theory based methods. The SiO₂ molecule is found to be chemisorbed on various sites on the Si surface and the most energetically favourable structure is on top of the dimers. The minimum energy pathways for the various adsorption channels indicate that the reaction is barrierless in all cases. The corresponding vibrational spectrum is also calculated and the adsorbed molecules are, as expected, found to have red-shifted vibrational frequencies. The energetically favourable adsorption sites and adsorption energies are comparable to the results found for SiO.     

Tetra-σ bonding adsorption of pyridine on Si(1 0 0)-2 × 1

We studied adsorption of pyridine on Si(1 0 0) at room temperature using high resolution photoemission spectroscopy (PES) and near edge X-ray adsorption fine structure (NEXAFS) in the partial electron yield (PEY) mode. The Si 2p, C 1s, N 1s spectra of pyridine on Si(1 0 0) showed that pyridine is chemisorbed on Si(1 0 0)-2 × 1 through the formation of the tetra-σ-bonded structure with the N atom and three C atoms. NEXAFS was conducted to characterize the adsorption geometry of pyridine on Si(1 0 0). The π* orbital of CC bond showed a good angle dependence in C K-edge NEXAFS spectra, and we were able to estimate the adsorption angle between chemisorbed pyridine of CC bond and the Si(1 0 0) surface using an analytical solution of NEXAFS intensity. We find the coexistence of two different tight bridges with the adsorption angles 42 ± 2° and 45 ± 2° with almost equal abundance.     

RAS: An efficient probe to characterize Si(0 0 1)-(2 × 1) surfaces

A complete inspection of the capabilities of reflectance anisotropy spectroscopy (RAS) in studying the adsorption of molecules or atoms on the Si(0 0 1)-(2 × 1) surface is presented. First, a direct comparison between RA spectra recorded on the clean Si(0 0 1)-(2 × 1) and the corresponding topography of the surface obtained using scanning tunneling microscopy (STM) allows us to quantify the mixing of the two domains that are present on the surface. Characteristic RA spectra recorded for oxygen, hydrogen, water, ethylene, benzene are compared to try to elucidate the origin of the optical structures. Quantitative and qualitative information can be obtained with RAS on the kinetics of adsorption, by monitoring the RA signal at a given energy versus the dose of adsorbate; two examples are presented: H₂/Si(0 0 1) and C₆H₆/Si(0 0 1). Very different behaviours in the adsorption processes are observed, making of this technique a versatile tool for further investigations of kinetics.     

The origin of narrowing of the Si 2p coincidence photoelectron spectroscopy main line of Si(1 0 0) surface

The Si 2p photoelectron spectroscopy (PES) main line of Si(1 0 0) surface measured in coincidence with the singles (noncoincidence) Si L_2,3-VV Auger-electron spectroscopy (AES) elastic peak is calculated. The agreement with the experiment is good. The present work is the first many-body calculation of the experimental coincidence PES spectrum of solid surface. The narrowing of the coincidence Si 2p PES main line compared to the singles one is due to the mechanism inherent in the coincidence PES. The inherent mechanism is explained by a many-body theory by which photoemission and Auger-electron emission are treated on the same footing.     

Atomic and electronic properties of furan on the Si(0 0 1)-(2 × 2) surface

The atomic and electronic properties of the adsorption of furan (C₄H₄O) molecule on the Si(1 0 0)-(2 × 2) surface have been studied using ab initio calculations based on pseudopotential and density functional theory. We have considered two possible chemisorption mechanisms: (i) [4 + 2] and (ii) [2 + 2] cycloaddition reactions. We have found that the [4 + 2] interaction mechanism was energetically more favorable than the [2 + 2] mechanism, by about 0.2 eV/molecule. The average angle between the CC double bond and Si(1 0 0) surface normal was found to be 22°, which is somewhat smaller than the experimental value of 28°, but somewhat bigger than other theoretical value of 19°. The electronic band structure, chemical bonds, and theoretical scanning tunneling microscopy images have also been calculated. We have determined a total of six surface states (one unoccupied and five occupied) in the fundamental band gap. Our results are seen to be in good agreement with the recent near edge X-ray absorption fine structure and high resolution photoemission spectroscopy data.     

Phase transition of Sr on Si (0 0 1): First principles prediction and experiment

The ability to understand and predict the phase diagrams of surface phases from first principles can be valuable for developing processes for growth of epitaxial structures. In the growth of epitaxial oxides on Si (0 0 1), a submonolayer phase of Sr plays a key role. The physical structure for this phase, which has 2 × 3 symmetry and occurs at 1/6 monolayer Sr coverage, was recently elucidated using both first principles theory and diffraction experiments [J.W. Reiner, K.F. Garrity, F.J. Walker, S. Ismail-Beigi, C.H. Ahn, Role of strontium in oxide epitaxy on silicon (0 0 1), Phys. Rev. Lett. 101 (10) (2008) 105503.]. Our approach to understanding the broader Sr/Si phase diagram combines density functional theory with a thermodynamic analysis of the phase equilibrium between a Sr lattice gas and the 2 × 3 structure. We use reflection high energy electron diffraction (RHEED) to experimentally determine the phase diagram, finding good agreement with theoretical predictions.     

Theoretical investigation of Mn adsorbates aside self-organised Bi nanolines on hydrogenated Si(0 0 1) surface

We have theoretically investigated the atomic structure, magnetic behaviour, and electronic properties of Mn adsorbates on hydrogen passivated self-organised Bi nanolines on the Si(0 0 1)surface. It is found that the most stable geometry for monolayer (ML) coverage of Mn is just underneath the first Si(0 0 1) surface layer. The Mn atoms in the optimised configuration are seven-fold coordinated with their neighbouring Si atoms. Total energy calculations suggest that the Mn adsorbates form a degenerate state of ferromagnetic and anti-ferromagnetic lines parallel and adjacent to the self-assembled Bi lines. The density functional band structure calculation within the local-spin density approximation shows that the ferromagnetic system behaves like a metal in both spin channels. On the other side, the anti-ferromagnetic phase exhibits a half-metallic phenomenon with semiconducting character for the majority spin channel and semi-metallic character for the minority spin channel.     

The origin of inter-dimer-row correlated adsorption for NH3 on Si(0 0 1)

We discuss the interaction between adsorbing ammonia molecules and pre-adsorbed ammonia fragments on the Si(0 0 1) surface, searching for experimental evidence of a H-bonded precursor state predicted by modelling. While correlations along dimer rows have already been identified, these mix substrate-mediated effects due to dimer buckling with ammonia–adsorbate effects. Correlations between fragments on neighbouring dimer rows are not affected by substrate effects (in this system), allowing an analysis of direct ammonia–adsorbate effects. We present an analysis of cross-row correlations in existing high-coverage STM data which shows significant correlations between NH₂ groups on neighbouring dimer rows over a significant range, providing evidence for the H-bonded precursor state with a range of around 10 Å. We discuss implications for the interpretation of STM images of ammonia on Si(0 0 1).     

A novel (8 × 4) superstructure as precursor to the c(4 × 4) phase during Sb/Si(0 0 1) desorption

The role of kinetics in the superstructure formation of the Sb/Si(0 0 1) system is studied using in situ surface sensitive techniques such as low energy electron diffraction, Auger electron spectroscopy and electron energy loss spectroscopy. Sb adsorbs epitaxially at room-temperature on a double-domain (DD) 2 × 1 reconstructed Si(0 0 1) surface at a flux rate of 0.06 ML/min. During desorption, multilayer Sb agglomerates on a stable Sb monolayer (ML) in a DD (2 × 1) phase before desorbing. The stable monolayer desorbs in the 600–850 °C temperature range, yielding DD (2 × 1), (8 × 4), c(4 × 4), DD (2 × 1) phases before retrieving the clean Si(0 0 1)-DD (2 × 1) surface. The stable 0.6-ML (8 × 4) phase here is a precursor phase to the recently reported 0.25-ML c(4 × 4) surface phase, and is reported for the first time.     

Structural and dynamical properties of Ru(0 0 0 1) surface

I performed density functional theory (DFT) calculations combined with MD simulations to study the structural relaxation of Ru(0001) surface. The surface relaxation of the topmost layer is found to be about ?4% at absolute zero temperature. Using MD simulations in the temperatures range of 50 K and 900 K, the effect is found to be minor on the surface relaxation as compared to Pd (1 1 1) clean surface. The effect of surface vibration is also investigated using a LEED code and shows no effect of the vibrational level on the IV curves, which rules out any disagreement between proper theory and LEED results of well prepared surfaces.     

Composition and morphological characteristics of chemically sprayed fluorine-doped zinc oxide thin films deposited on Si(1 0 0)

Fluorine-doped zinc oxide thin films (ZnO:F) were deposited on Si(1 0 0) substrates by the chemical spray technique (CST) from an aged-solution. The effect of the substrate temperature on the morphology and composition of the ZnO:F thin films was studied. The films were polycrystalline, with a preferential growth along the ZnO (0 0 2) plane, irrespective of the deposition temperature. The average crystal size within the films was ca. 35 nm and the morphology of the surface was found to be dependent on the substrate temperature. At low substrate temperatures irregular-shaped grains were observed, whereas at higher temperatures uniform flat grains were obtained. Elemental analysis showed that the composition of the films is close to stoichiometric ZnO and that samples contain quite a low fluorine concentration, which decreases as a function of the deposition temperature.     

Room-temperature deposition of group III metals on Si(1 0 0): A comparative study of nucleation behavior

In this paper, we compare and contrast the processes of nucleation and subsequent growth of single-atom wide metal chains formed when group III metals (Al, Ga, In) are deposited onto Si(1 0 0) at room-temperature (RT). Employing Density Functional Theory (DFT) calculations, diffusion pathways on Si(1 0 0) surface are identified and their associated activation barriers are calculated. Then, the relative stabilities of various C-defect-pinned chains are examined by comparing the relevant adsorption energies. We also account for the observation that defect-nucleated chains grow on only one side of a C-defect by showing that the latter’s presence breaks the symmetry between the two previously equivalent binding sites on either side and rendering one much more stable than the other. Next, a growth model tailored for each group III metal/Si(1 0 0) system and incorporating the above results was simulated using Kinetic Monte Carlo (KMC) techniques to show that the surface morphologies generated by this model accurately reflect the observed ratio of homogeneously to heterogeneously nucleated chains. Finally, we examine through KMC simulations the consequences of the contrasting roles of a defect on In/Si(1 0 0) and Al/Si(1 0 0) – it captures adatoms in the former while it merely blocks direct adatom diffusion in the latter – on key quantities such as the mean island density.     

Study of thermal oxidation of LaSix/Si(1 0 0) by grazing incidence electron-induced X-ray emission spectroscopy

A new X-ray emission spectroscopy (XES) apparatus for analyzing nondestructively the chemical states of the inner regions of layered materials was constructed. Using electron excitation at grazing incidence, it also enables the analyzing depth to be confined to the surfaces of the materials. The apparatus was employed to the study of oxidation of a La silicide layer formed on a Si substrate. By comparing the Si Kβ emissions with results by XPS analysis, it was concluded that the Si Kβ emission band of the oxidized sample at the excitation energy of 3.0 keV represents the Si 3p density of states (DOS) of a LaSiO mixed oxide. The variations of the spectra at increasing electron beam energies were compared with probing depths calculated by an empirical model. This result indicates that we can analyze the chemical states of a mixed oxide layer of one to two tens angstroms in thickness, and nondestructively probe into the depth of about several tens angstroms.