掺Tm钒酸钇的光学性能

钒酸钇(YVO₄)晶体有高的激光损伤阈值和高的激光输出斜率效率,也有很好的机械性能和化学稳定性.从测量Tm:YVO₄晶体的吸收谱入手,考虑该晶体的各向异性效应,拟合出Tm³⁺的光学强度参量,进一步得到了振子强度f,辐射跃迁速率A和积分发射截面Σ等光学参量.在350—2500nm范围内,YVO₄晶体基质的吸收很小,而Tm³⁺在YVO₄晶体中发光能力很强;特有的是蓝光¹     

抗共振环稳定被动调Q 激光的作用

本文从理论出发,分析抗共振环(Anti-ResonantRing-ARR)稳定调Q 激光脉冲的作用.将新型调Q晶体Cr⁴⁺:YAG置于ARR中心,在平-ARR介稳腔中获得能量起伏0.34%的高稳调Q单脉冲输出.     

LD抽运Er3+，Yb3+共掺磷酸盐玻璃被动调Q激光器的理论分析和数值计算

研究了以Co²⁺:MgAl₂O₄晶体为饱和吸收体的LD抽运Er³⁺,Yb³⁺共掺磷酸盐玻璃激光器.针对双掺离子之间的能量传递和Er³⁺的多种跃迁过程，结合Co²⁺:MgAl₂O₄晶体中Co²⁺离子的饱和吸收特性，给出了详尽的速率方程，在其基础上进行了数值分析，分析了输出镜透过率、激光介质长度、谐振腔长度、腔内往返损耗、饱和吸收体长度对激光阈值、峰值功率、单脉冲能量以及脉冲宽度的影响.     

钨酸钇钠晶体中Tm3+的光谱特性

测量了Tm³⁺:NaY(WO4)₂晶体的吸收光谱、发射光谱和激发光谱，利用J_O理论计算了钨酸钇钠晶体的强度参数：Ω₂=7.21304×10^-20cm²，Ω4=0.504766×10^-20cm²，Ω6=0.977784 ×10^-20cm²，以及Tm³⁺光学参数包括各能级的荧光寿命和荧光分支     

Al2O3:V3+晶体局域结构及其自旋哈密顿参量研究

提出了解释掺杂离子局域结构畸变的配体平面移动模型，建立了此模型下晶体微观结构与自旋哈密顿参量之间的定量关系.在考虑自旋与自旋、自旋与另一电子轨道和轨道与轨道作用等微小磁相互作用的基础上，采用全组态完全对角化方法，对Al₂O₃晶体中V³⁺的局域结构和自旋哈密顿参量进行了系统的研究.结果表明，V³⁺掺入Al₂O₃晶体后，上下配体氧平面间距离增大了0.0060 nm.从而成功地解释了Al₂O₃:V³⁺晶体的自旋哈密顿参量.在此基础上，研究了三角晶场下3d²离子自旋哈密顿参量的微观起源.研究发现，自旋三重态对自旋哈密顿参量的贡献是主要的，微小磁相互作用对自旋哈密顿参量的贡献只与自旋三重态有关.     

自锁模飞秒掺铬的镁橄榄石激光器的实验研究

用波长为1.06μm的Nd:YAG激光器泵浦Cr⁴⁺:forsterite晶体,实现了Cr⁴⁺:forsterite激光器的自锁模飞秒激光运转,在吸收泵浦功率为8W的条件下,得到了脉冲宽度为85fs,中心波长为1246nm,平均输出功率为200mW的稳定锁模输出。     

LD端面泵浦Cr4:YAG被动调Q激光器输出特性研究

对激光二极管端面泵浦Cr⁴⁺:YAG被动调QNd:YAG激光器输出特性进行了实验研究.实验研究发现,激光器输出功率及脉冲重复频率随谐振腔长度增大而增大.为解释这一实验现象,测量了泵浦光斑在激光晶体内尺寸,同时计算了激光晶体及Cr⁴⁺:YAG晶体内的基模激光光斑半径随谐振腔长度变化.分析结果表明:激光晶体内泵浦光斑尺寸远小于激光晶体内基模光斑半径,腔模间交叠效率较低;当腔长增加时,激光晶体内的基模激光光斑减小,腔模间交叠效率增加,从而导致输出功率及脉冲重复频率随腔长增加而增加;另外,Cr⁴⁺:YAG晶体内光斑半径也随谐振腔长度减小,引起Cr⁴⁺:YAG晶体漂白时间缩短,导致脉冲重复频率随腔长增加而增加.     

Tm3+/Yb3+ ∶LaF3纳米体系中掺杂Yb3+ 离子对Tm3+ 离子荧光发射的影响

为研究Yb³⁺离子浓度变化对Tm³⁺离子在蓝色波段荧光强度的影响,以NaF和La(NO₃)₃为原料,采用水热法制备了Tm³⁺和Yb³⁺共掺的Tm³⁺/ Yb³⁺∶LaF₃纳米颗粒.用X射线衍射对LaF₃纳米颗粒进行表征的结果显示,纳米晶体结构呈六方相.透射电镜的观测结果显示,纳米颗粒样品大小均匀、分散性良好.在波长为800 nm的激光激发下,观测到了上转换蓝光发射,其中包括波长为474 nm和479 nm的较强的荧光辐射(相应的跃迁为1G4→3H6)和波长位于450 nm的强度较弱的荧光发射(相应的跃迁为1D2→3F4).通过观测不同Yb³⁺离子浓度条件下共掺Tm³⁺/Yb³⁺∶LaF₃样品的荧光光谱,研究了Yb³⁺离子掺杂浓度对于Tm³⁺离子的荧光发射的影响,并探讨了产生这种现象的原因.研究结果显示,对于1G4→3H6跃迁产生的荧光发射(474 nm),当Yb³⁺离子浓度增大时,反向能量传递速率的增加导致了荧光强度的增大.然而,当Yb³⁺离子浓度增大到一定程度时,Yb³⁺离子激发态能级寿命的减少将引发荧光强度的下降.相比较而言,Yb³⁺离子的浓度的变化对于1D2→3F4跃迁产生的位于450 nm处荧光强度的影响较弱.     

Tm3+/Yb3 :LiYF4单晶的高效近红外量子剪裁及其在光伏电池中的应用

采用改进的坩埚下降法成功地生长了Tm/Yb共掺氟化钇锂单晶. 该单晶体具有每吸收一个蓝色光子并能发射出2个1000 nm近红外光子的下转换发光效应. 测定了样品的激发光谱、发射光谱和荧光衰减曲线. 在465 nm蓝光激发下观察到由Yb³⁺：²F_5/2→²F_7/2能级跃迁所致的960～1050 nm 波段的发射带,此发光带源于Tm³ 对Yb³ 离子的能量下转换过程. 应用Inokuti-Hirayama模型,研究了晶体的能量转换过程,结果表明Tm³ 向Yb³ 的能量传递是一个电偶极子相互作用机制过程. 当Tm³ 与Yb³ 离子的掺杂浓度为0.49mol%与5.99mol%时,单晶的量子剪裁效率达到最大值167.5%.     

16O+115In反应的全熔合与非完全熔合

在92和71MeV ¹⁶O离子与¹¹⁵In的相互作用中,用核化学技术测量了20个反应余核的角分布和微分射程分布.分析了这些余核的生成特征,指出随着碰撞参数的增加,反应机制从全熔合经过质量和动量转移逐渐减小的非完全熔合向直接反应连续演变.与¹⁶O+⁶⁵Cu反应相比,¹⁶O+¹¹⁵In反应中非完全熔合的贡献显著增加.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.