MgF2改性Alq3纳米复合材料的制备及其对OLED抗老化性能的提高

提高有机电致发光器件(OLED)的稳定性和寿命是其市场化应用中需要解决的关键问题.本文从提高发光材料自身的稳定性出发,以Mg(CF₃COO)_2-x(CH₃COO)_x溶胶为前驱体,将其与8-羟基喹啉铝(Alq₃)混合浓缩成糊状后, 300 ℃真空烧结,经过MgF₂的生成和Alq₃的相变后,形成了一系列Mg含量不同的具有超结构ε相的纳米复合材料Alq₃-MgF₂.研究结果表明,相比于纯Alq₃, Alq₃-MgF₂纳米复合材料制备的OLED可以很好地保持Alq₃的发光特性,同时,其抗老化性能得到显著提高.特别是, Mg(CH₃COO)₂投料量为Alq₃的5% (摩尔分数)时,所得Alq₃-MgF₂纳米复合材料制备的器件抗老化性能最优,在空气中老化72 h,最大发光亮度仍保持在起始值的93.5%;而Alq₃制备的OLED在空气中老化24 h后基本失活.     

富锂层状正极材料Li2MnO3的表面改性及其电化学性能研究

Li₂MnO₃正极材料具有较高的理论容量（459 mAh·g ^-1）,不仅安全无毒还能够大大降低电池的制造成本,从而受到越来越多的关注. 然而,较低的首圈库仑效率和较差的循环性能妨碍了其在锂电池中的实际应用. 在此,作者研究了MgF₂涂层对Li₂MnO₃正极材料的电化学性能. 结果表明,MgF₂涂层诱导部分层状Li₂MnO₃向尖晶石相转化,从而降低了首圈不可逆容量,提高库仑效率. 重量比为0.5%、1.0%和2.0%的MgF₂涂层电极的初始库仑效率分别为70.1%、77.5%和84.9%,而原始电极仅为57.7%. 充放电曲线表明,1.0wt.%MgF₂涂层改性的Li₂MnO₃具有最高的充放电容量和最佳的循环稳定性. 40个循环后1.0wt.%MgF₂涂层样品的容量保持率为81%,远高于原始样品的容量保持率（53.6%）. 电化学阻抗谱结果表明MgF₂涂层减少了不利成分的快速沉积,并改善了电极的循环稳定性.     

化学镀镍体系次亚磷酸钠氧化中间产物的ESR研究

化学镀镍是借助 Na H2 PO2 在具有催化活性金属表面的阳极氧化将溶液中的镍离子还原成金属镍 .伴随镍的沉积 ,表面同时有氢气析出 .同位素研究表明 [1,2 ] ,析出的氢气一部分为溶液中 H+或 H2 O的阴极还原 ,另一部分来自 Na H2 PO2 的阳极氧化过程 .Meerakker等[3～ 5 ] 认为 ,Na H2 PO2 的氧化经历了H2 PO-2 H+ HPO-.2 异相前置转化步骤 ,HPO-.2 阴离子自由基发生阳极氧化的同时伴有 H复合生成氢气过程 .而另一些研究者 [6～ 8] 认为 ,Na H2 PO2 的氧化过程为 H2 PO-2 + H2 O H2 PO-3 + 2 H,仅有 H自由基生成 ,并不产生 H…     

ALD-Al2O3涂层保护的高抗湿5-氨基戊酸铰链甲胺铅溴钙钛矿薄膜

近年来,混合铅卤钙钛矿材料在光电领域引发的研究热潮引人注目。然而,钙钛矿材料对水和氧气的敏感性严重的阻碍了其实用化进程。在众多的稳定钙钛矿的方法中,利用简单的原子层沉积方法(Atomic layer deposition,ALD)在钙钛矿表面沉积一层保护层的技术具有极大的潜力。而ALD应用的困难在于,在常规的ALD过程中,做为氧源的H2O和O3对铅卤钙钛矿有着腐蚀作用。在本文,我们提出将双官能团的5-氨基戊酸(5-Aminovaleric acid,AVA)引入到CH₃NH₃PbBr₃(MAPbBr₃)钙钛矿晶格层中,形成稳定的铰链结构的2D/3D钙钛矿AVA(MAPbBr₃)2。AVA的引入可以钝化并防止ALD过程中水对钙钛矿的侵蚀,从而成功地直接在钙钛矿表面沉积了Al₂O₃保护层。覆盖了保护层的AVA(MAPbBr₃)2钙钛矿薄膜获得了优异的热稳定性和抗水性。     

Ni(OH)2修饰的三聚氰胺泡沫用于可压缩超级电容器电极

通过化学镀和电化学镀的方法制备了一种Ni(OH)₂电化学活性材料修饰三聚氰胺泡沫(MF)可压缩骨架的超级电容器电极材料MF/Ni(OH)₂。MF/Ni(OH)₂可压缩电极材料表现出最佳的电容性能,例如循环稳定性(即使在40 mA/cm^-3的电流密度下经过2000次充放电循环后,可压缩电极仍能保持90.63%的初始电容)和可压缩稳定性(即使在压缩率为50%时,仍具有97.88%的电容保持率)。层状可压缩超级电容器由MF/Ni(OH)₂弹性材料作为阳极,镍/碳(Ni/C)为阴极以及实验室中常用的滤纸作隔膜材料组成。这种超级电容器装置在不同的压缩下表现出良好的电化学性能和优异的压缩稳定性。最后,使用可压缩的超级电容器来点亮LED灯,以展示其在柔性电子设备中的应用。这些优化的电化学和机械性能表明MF/Ni(OH)₂可作为可压缩超级电容器的应用中的候选电极。     

C_6H_2(OH)_3CH_3氧化成羟基苯甲酸反应路径的DFT研究

运用密度泛函(DFT)理论,采用Materials Studio 8.0,用GGA/BP方法研究了C_6H_2(OH)_3CH_3氧化成羟基苯甲酸的反应路径。结果表明,甲基上的氢原子被氧化成羟基以及羟基被氧化为醛基及醛基被氧化成羧基均为放热过程。分子C_6H_2(OH)_3CH_3中甲基氧化成羧基的主路径为三个氢原子氧化反应路径,其路径为C_6H_2(OH)_3CH_3+3O→C6H2(OH)3C(OH)3→C6H2(OH)3COOH+H2O,该路径受限于羟基直接被氧化成羧基过程,需克服130 k J/mol的反应势垒,反应速率常数对数ln(k)为-22.96 s-1;醛基、羟基优先被氧化成羧基的顺序为:-CHO-C(OH)3-HC(OH)2-H2C(OH);提高反应温度、氧气浓度均有利于羟基苯甲酸的生成,适当的催化剂有利于促进整个反应的进行。     

AOPAN@Mg(OH)2多层次电纺纤维膜的制备及除铬性能

以含有—NH₂和C═N的偕胺肟化聚丙烯腈(AOPAN)纳米纤维膜为载体, 通过水热法在AOPAN纳米纤维膜表面原位生长片状Mg(OH)₂纳米粒子, 得到具有多层次结构的有机-无机电纺复合纳米纤维膜[AOPAN@Mg(OH)₂], 并研究了AOPAN@Mg(OH)₂的除铬性能. 研究结果表明, 当水热温度为40 ℃, 水热时间为7 h时, AOPAN纳米纤维膜表面形成了明显的多层次结构的Mg(OH)₂纳米晶体. 当溶液pH=2时, AOPAN@Mg(OH)₂复合纳米纤维膜对Cr(Ⅵ)的吸附符合Langmuir模型, 且满足二级动力学方程, 5 h后最大吸附量达到123.5 mg/g. AOPAN@Mg(OH)₂复合纳米纤维膜中含有—NH₂基团和Mg(OH)₂纳米粒子, 在酸性条件下可以质子化为带正电的—N\begin{array}{c}{H}_3^{+}\end{array}和Mg(OH)₂H⁺, 通过静电吸附更易与HCr\begin{array}{c}{O}_4^{-}\end{array}结合. 此类复合纳米纤维膜材料在水体中易取出, 并且在稀NaOH溶液中可以解吸附, 循环使用4次去除率仍可以保持在50%以上.     

Ni-P化学镀反应速率及机理研究

通过镀层分析和析氢量测量得到Ni-P镀层的沉积速度和H2PO2的分解速度·以混合电位理论为基础，对Ni－P电极在不同组成饮液中的极化曲线进行分解得到以化学镀电流形式所表示的反应速率·将两种方法所得结果进行对照，确定H2PO2氧化时电子迁移数为1，并用原子红-电化学联合理论解释溶液PH对反应速率及化学镀效率的景响．     

Boosting the Energy Density of Flexible Asymmetric Supercapacitor with Three Dimensional Fe2O3 Composite Brush Anode

Flexible asymmetric supercapacitor is fabricated with three dimensional(3D)Fe2O3/Ni(OH)2 composite brush anode and Ni(OH)2/MoO2 honeycomb cathode.Particularly for 3D composite brush anode,a layer of thin Fe2O3 film is firmly adhered on a 3D Ni brush current collector with the assist of Ni(OH)2,functioning as both adherence layer and pseudocapacitive active material.The unique 3D Ni brush current collector possesses large surface area and stretching architecture,which facilitate to achieve the composite anode with high gravimetric capacitance of 2158 F/g.In terms of cathode,Ni(OH)2 and MoO2 have a synergistic effect to improve the specific capacitance,and the resulting Ni(OH)2/MoO2 honeycomb cathode shows a very high gravimetric capacitance up to 3264 F/g.The asymmetric supercapacitor(ASC)has balanced cathode and anode,and exhibits an ultrahigh gravimetric capacitance of 1427 F/g and an energy density of 476 W·h/kg.The energy density of ASC is 3-4 times higher than those of other reported aqueous electrolyte-based supercapacitors and even comparable to that of commercial lithium ion batteries.The device also shows marginal capacitance degradation after 1000 cycles'bending test,demonstrating its potency in the application of flexible energy storage devices.     

CuCrO2的合成及其复合催化剂的光催化性能

以硝酸铬和硝酸铜为原料,通过半湿法经两种不同路径合成了CuCrO₂半导体物质。分别采用热重-差示扫描（TG-DSC）、X射线衍射（XRD）、紫外-可见漫反射（UV-vis DR）、扫描电镜（SEM）及X射线光电子能谱（XPS）对样品进行了表征分析。确立了以氨水为Cr³⁺沉淀剂制得的氢氧化铬沉淀中加入硝酸铜溶液是合成CuCrO₂较适宜的路径。借助TG-DSC和XRD的分析结果确立前驱体在热处理的过程中,含Cr物相的变化历程为Cr（OH）₃ → CuCrO₄ → CuCr₂O₄ → CuCrO₂。通过机械研磨的方法合成了CuCrO₂-WO₃和CuCrO₂-ZnO复合型催化剂,对其进行了XRD、SEM和XPS表征分析,并测试了复合催化剂的光催化活性。结果表明,与单独使用CuCrO₂相比,无论是以高压汞灯,还是以氙灯为光源,CuCrO₂-WO₃和CuCrO₂-ZnO的光催化产氢活性都有显著提高。     

氢氧化镍纳米线/三维石墨烯复合材料的制备及其电化学性能

采用水热法制备了氢氧化镍纳米线/三维石墨烯复合材料及作为比较的三维石墨烯、氢氧化镍纳米线、还原氧化石墨烯和氢氧化镍纳米线/还原氧化石墨烯, 通过X射线衍射、扫描电镜、热失重分析和氮气吸脱附表征了材料的形貌、结构和组成, 并采用循环伏安法和恒电流充放电测试了复合材料的电化学性能. 结果表明: 氢氧化镍纳米线/三维石墨烯复合材料中直径为20-30 nm的氢氧化镍纳米线和三维结构的石墨烯紧密结合, 相互交联形成网状结构, 其比表面积达到136 m²·g^-1, 孔径分布20-50 nm, 氢氧化镍纳米线的含量达到88% (w,质量分数). 在6 mol·L^-1的KOH电解液中, 复合材料的比电容在1 A·g^-1电流密度下达到1664 F·g^-1, 在1 A·g^-1电流密度下循环3000 次后的比电容保持率为93%. 将复合材料的比电容和循环性能与氢氧化镍纳米线、氢氧化镍纳米线/还原氧化石墨烯、三维石墨烯和还原氧化石墨烯的性能进行比较, 发现三维石墨烯较还原氧化石墨烯具有更高的比表面积和三维多孔结构, 可以更大地提高活性物质的利用率, 进而提高复合材料的比电容和稳定性.     

Enhanced Corrosion Resistance and Discharge Performance of Mg-MnO2 Battery by Na2SiO3 Additive

Corrosion resistance and delayed action are major obstacles that severely limit the practical application of Mg alloy in battery fields. In this work, the effects of Na2SiO3 on the electrochemical behavior of the AZ31B Mg alloy in MgSO4-Mg(NO3)2 composite solution[0.14 mol/L MgSO4,1.86 mol/L Mg(NO3)2] were investigated. Electrochemical tests were carried out using electrochemical impedance spectroscopy, galvanostatic discharge, and linear sweep voltammograms. The results indicate that the impedance value increases by nearly fourfold, and the delayed time decreases from 2.1 s to 0.6s. Battery perfoniiance test reveals that the addition of Na2SiO3 significantly improves the discharge specific capacity of Mg-MnO2. The surface morphology and composition of corrosion products from Mg alloys were studied by scanning electron microscopy(SEM) and Fourier translonn infrared spectroscopy(FTIR), respectively. The SEM images of the AZ31B Mg alloys in composite solution with or without Na2SiO3 additive have an evident distinction due to the ionnation of new insoluble compound.FTIR result confirms that the corrosion products accumulated on the alloy surface in the electrolyte containing Na2SiO3 are mainly composed of Mg(OH)2, MgCO3, and MgSiO3.     

原位生长Pd/Ni(OH)2/NF复合催化剂及其析氢性能

采用水热合成法在泡沫镍上原位构建了低贵金属含量的钯/氢氧化镍纳米复合催化剂（Pd/Ni（OH）₂/NF）。通过扫描电镜,能谱仪,X射线衍射仪和X射线光电子谱仪等分析技术表征了催化剂的形貌和微观结构;运用线性扫描伏安法,电化学阻抗谱和计时电流法等手段研究了催化剂的催化析氢性能。实验结果显示复合催化剂具有特殊的微观构型,超薄的Ni（OH）₂薄片生长在泡沫镍表面,纳米尺寸的钯均匀地镶嵌在氢氧化镍薄片中。催化剂表面的氢氧化镍有利于促进水的解离,加快氢中间体的形成;均匀分散的钯极易吸附解离的氢中间体,快速地复合成氢气分子。我们发现复合催化剂能协同加快析氢反应过程,极大地降低析氢过电位,提高了析氢活性。此外,复合催化剂原位生长在泡沫镍上,有效地提高了催化电极的稳定性。     

Complexes of nitrilotrimethylphosphonic acid with cobalt, nickel, copper and zinc

Substances of the types MH₄ntmp, Mg₃[M(Hntmp)]₂, M₂H₂ntmp and Mg[M₂(Hntmp)]₂, where M = Co, Ni, Cu, Zn and H₆ntmp = N[CH₂PO(OH)₂]₃ were prepared. The sodium and cesium salts of the [Co(Hntmp)]³⁻ complexes were also prepared. The IR and electronic spectra and the experimental magnetic susceptibilities indicate that these are high-spin complexes. The coordination surroundings of the central atom consist of a highly distorted octahedron of the ligand oxygen atoms. The nitrogen atom is not coordinated to the central atom.     

Luminescence properties of CdTe QDs embedded in Zn5(CO3)2(OH)6 matrix

CdTe@Zn₅(CO₃)₂(OH)₆ composites were synthesized by a hydrothermal method. CdTe@Zn₅(CO₃)₂(OH)₆ composite nanospheres were characterized via X-ray diffraction, scanning electron microscopy, energydispersive X-ray spectroscopy, and photoluminescence (PL). The hydrothermal reaction time and the mole ratios of Zn/Te played important roles in the growth and fluorescence intensity of CdTe@Zn₅(CO₃)₂(OH)₆ composites. The composite powders showed peak PL at 578 nm at 1.6 times the intensity of powdered CdTe QDs. CdTe@Zn₅(CO₃)₂(OH)₆ exhibited a strong yellow fluorescence emission, and its preparation method was easy and economical. Therefore, CdTe@Zn₅(CO₃)₂(OH)₆ offers potential applications in biological markers and light-emitting diodes.     

Effect of metal oxide additives on the thermal decomposition of perchlorates, oxalates and hydroxides

The effects of -Fe₂O₃ and -Al₂O₃ additives on the thermal decomposition of perchlorates, oxalates and hydroxides were investigated by means of DTA, TG and X-ray techniques. It was found that the oxide additives catalytically promoted the decomposition of perchlorates (NaClO₄, KClO₄ and Mg(ClO₄)₂) and resulted in a lowering of the initial decomposition temperature (T_i). On the other hand, the oxides showed no significant effect on the decomposition of oxalates (FeC₂O₄ and CuC₂O₄) and hydroxides (Mg(OH)₂ and Al(OH)₃).

The thermal decomposition of KClO₄ was chosen to compare the catalytic effect of twelve metal oxides. The results indicated that the transition metal oxides such as Cr₂O₃, -Fe₂O₃ and CuO markedly accelerated the decomposition; these oxides resulted in a solid-phase decomposition before fusion of KClO₄, and the initial decomposition temperature (T_i) of KClO₄ with oxides was about 100–200°C lower than that without catalyst. The oxides such as -Al₂O₃ and MgO resulted in a slight lowering of the temperature of the fusion and promoted the molten-phase decomposition of KClO₄, but their effects were not so remarkable as those of the transition metal oxides. The modified catalytic mechanisms of transition metal oxides were proposed by considering the electron transfer and the oxygen-abstraction models.     

Potentiometric titration of Co(II) in presence of Co(III)

A potentiometric titration for cobalt(II) determination in the presence of Co(III) based on the oxidation of Co(II) with Na₂CrO₄ in ethylenediamine medium and back-titration of the oxidant excess with (NH₄)₂Fe(SO₄)₂ in acid medium is described. The titration is monitored with a Pt indicator electrode and carried out until the greatest jump of potential from one drop of titrant appears. A RSD smaller than 1.5% has been obtained for 50–300 μmol Co(II). The method proposed was applied in the analysis of a new type electroless copper plating solutions containing Co(II)-ethylenediamine complex compounds as reducing agents. Cu(II), Co(III) and Cr(III) do not interfere in the determination of Co(II).     

煤中负载氢氧化钙对催化气化和甲烷化反应的影响

以不连沟次烟煤为研究对象,在加压固定床中研究Ca(OH)_2对煤气化及负载Ca(OH)_2煤热解半焦的甲烷化反应活性。结果表明,煤中添加Ca(OH)_2能够明显促进气化反应的进行和甲烷的生成,随着气化温度的升高和负载量的增加,碳转化率增加,但负载量存在饱和点。不同的催化剂负载方式对Ca的分散有一定的影响,进而影响其催化性能。含有Ca的半焦能够明显促进甲烷化的进行,出口气甲烷含量随甲烷化温度和催化剂负载量的升高而增强。采用红外光谱分析揭示了煤负载Ca(OH)_2的离子交换机理和扩散过程,这一过程影响煤气化反应性能。     

Efficient activation of peroxymonosulfate by hollow cobalt hydroxide for degradation of ibuprofen and theoretical study

Hollow structure cobalt hydroxide (h-Co(OH)₂) was synthesized via a solvothermal-hydrothermal method and presented high activation activity for peroxymonosulfate to degrade ibuprofen.     

Synthesis of spherical nanoparticles of Cu2L2O5 (L=Ho, Er) from W/O microemulsions

Nanoparticles of Cu₂L₂O₅ (L=Ho, Er) (15–25 nm in size) were synthesised by the intermediate use of W/O microemulsions. In this process the aqueous cores of water/cetyltrimethylammonium bromide/n-octane/1-butanol microemulsions were used as microreactors for the precipitation of Cu₂Ho₂(CO₃)₄(OH)₂ (25–30 nm) and Cu₂Er₂(CO₃)₄(OH)₂ (10–40 nm) as precursors. These mixed salts were separated and further decomposed to the corresponding mixed oxides at 900°C for 16 h. All solids were characterised by scanning and transmission electron microscopy, IR, XRPD, ICP-OES, TGA, XPS measurements and elemental analyses.