Direct acetylation and determination of chlorophenols in aqueous samples by gas chromatography coupled with an electron-capture detector

A method was developed that offers a rapid, simple and accurate technique for the determination of chlorophenols at trace levels in aqueous samples with very limited volumes of organic solvents. These compounds were acetylated, then preliminarily extracted with n-hexane. The enriched chlorophenols were directly analyzed using gas chromatography with an electron-capture detector. The detection limits were in the range of 0.001-0.005 mg/L, except for 2-chlorophenol, which was always above 0.013 mg/L. Relative standard deviation for the spiked water samples ranged from 2.2 to 6.1%, while relative recoveries were in the range of 67.1 to 101.3%.     

Development of a solid-phase microextraction method with micellar desorption for the determination of chlorophenols in water samples. Comparison with conventional solid-phase microextraction method

A novel analytical method is presented for the determination of chlorophenols in water. This method involves pre-concentration by solid-phase microextraction (SPME) and an external desorption using a micellar medium as desorbing agent. Final analysis of the selected chlorophenols compounds was carried out by high-performance liquid chromatography (HPLC) with diode array detection (DAD). Optimum conditions for desorption, using the non-ionic surfactant polyoxyethylene 10 lauryl ether (POLE), such as surfactant concentration and time were studied. A satisfactory reproducibility for the extraction of target compounds, between 6 and 15%, was obtained, and detection limits were in the range of 1.1-5.9ngmL(-1). The developed method is evaluated and compared with the conventional one using organic solvent as a desorbing agent. The method was successfully applied to the determination of chlorophenols in water samples from different origin. This study has demonstrated that solid-phase microextraction with micellar desorption (SPME-MD) can be used as an alternative to conventional SPME method for the extraction of chlorophenols in water samples.     

In-capillary solid-phase extraction-capillary electrophoresis for the determination of chlorophenols in water

A novel CE method combined with SPE in a single capillary was developed for analysis of chlorophenols in water. A frit of 0.5 mm was first made by a sol-gel method, followed by packing a SPE sorbent in the inlet end of the capillary. Two phenol derivatives, 2,4-dichlorophenol and 2,4,5-trichlorophenol, were used as the model compounds. By loading sample solutions into the capillary, the two chlorophenols were extracted into the sorbent. They were desorbed by injecting only about 4 nL of methanol. Finally, the analytes were separated by conventional CE. The technique provided a concentration enhancement factor of over 4000-fold for both chlorophenols. The detection limits (S/N = 3) of 2,4-dichlorophenol and 2,4,5-trichlorophenol were determined to be 0.1 ng/mL and 0.07 ng/mL, respectively. For replicate analyses of 5 ng/mL of 2,4-dichlorophenol, within-day and between-day RSDs of migration time, peak height and peak area were in the range of 1.8-2.0%, 4.0-4.4% and 4.1-4.6%, respectively. The method shows wide linear range, acceptable reproducibility and excellent sensitivity, and it was applied to the analyses of spiked river water samples. The capillary packed with the SPE sorbents can be used for more than 400 runs without performance deterioration.     

Trace Enrichment and HPLC Analysis of Chlorophenols in Environmental Samples,Using Precolumn Sample Preconcentration and Electrochemical Detection

Abstract

A HPLC method has been developed for trace analysis of chlorophenols in the 0.2–2 ppb range from spiked water samples. Simple liquid-liquid extraction followed by on-line preconcentration of total mono- and dichlorophenols has been performed using a divinylbenzene-styrene copolymeric sorbent (PRP₁) as packing material for the precolumn. The chlorophenols have been eluted from the precolumn on an analytical column (5μm LiChrosorb RP-18, 12.5 cm × 4 mm) by use of a switching valve system followed by separation. Detection was carried out with an electrochemical detector. The linearity of the detector response has been proved over two orders of magnitude. The detection limit of chlorophenols by means of the electrochemical method is in the lower picogram range. The recoveries of the isomeric chlorophenols from spiked river water samples having initial concentrations of 2ppb are usually 70–90%. The procedure has been applied to drinking water and river water.     

Determination of chlorophenols in red wine using ionic liquid countercurrent chromatography as a new pretreatment method followed by high‐performance liquid chromatography

A countercurrent chromatography method for the enrichment and cleanup of chlorophenols from food samples was successfully established by using an ionic‐liquid‐modified two‐phase solvent system composed of dichloromethane containing 2% 1‐butyl‐3‐methylimidazolium bis(trifluoromethanesulfonyl)imide and water. The column was firstly filled with the organic stationary phase, and then a large volume of sample was pumped into the column after it was equilibrated with pure water at the rotation speed. Finally, the trace amounts of chlorophenols extracted and enriched in the stationary phase were eluted out by an alkaline mobile phase and determined by high‐performance liquid chromatography. Under optimized conditions, the enrichment and cleanup of the chlorophenols can be fulfilled online with enrichment factors (34–65) and high recoveries (84.69–95.23%). The method has been applied to the determination of chlorophenols in real red wine samples with the limits of detection in the range of 1.89–4.21 μg/L. The present method is highly suitable for the pretreatment of large volume of aqueous sample for the determination of trace amounts of contaminants in food and environmental samples.     

Microwave-assisted extraction combined with dispersive liquid-liquid microextraction as a new approach to determination of chlorophenols in soil and sediments

A new method was applied for extraction of five chlorophenols from soil and marine sediment samples. Microwave-assisted extraction coupled with dispersive liquid-liquid microextraction followed by semi-automated in-syringe back-extraction technique was used as an extraction technique. Microwave-assisted extraction was performed by using 2.0 mL of alkaline water at pH 10.0. After extraction, the pH of extraction solution was adjusted at 6.0 and dispersive liquid-liquid microextraction procedure was done using 1.0 mL of acetone as a disperser solvent and 37.0 μL of chlorobenzene as extraction solvent. About 20.0 ± 0.5 μL sedimented phase was collected after centrifugation step. Then, chlorophenols were back extracted into 20 μL of alkaline water at pH 12.0 within the microsyringe. Finally, 20.0 μL of aqueous solution was injected into high performance liquid chromatography with ultra violet detection for analysis. The obtained recovery and preconcentration factors for the analytes were in the range of 68.0-82.0% and 25-30, respectively, with relative standard deviations ≤7.6%. The limits of the detection were found in the range of 0.0005-0.002 mg/kg. The method provides a simple and fast procedure for the extraction and determination of chlorophenols in soil and marine sediment samples.     

Application of liquid-liquid-liquid microextraction and ion-pair liquid chromatography coupled with photodiode array detection for the determination of chlorophenols in water

A method termed as liquid-liquid-liquid microextraction was utilized to extract chlorophenols from water. The extracted chlorophenols, present in anionic form, were then separated, identified, and quantitated by ion-pair high-performance liquid chromatography with photodiode array detection (HPLC/DAD). For trace chlorophenol determination using HPLC/DAD, the chlorophenolate anion provides a better ultraviolet spectrum for quantitative and qualitative analyses than does uncharged chlorophenol. This is due to the auxochromic effect of the phenolate anion. In the study, experimental conditions such as organic phase identity, acceptor phase volume, sample agitation, extraction time, acceptor phase NaOH concentration, donor phase HCl concentration, salt addition, and UV absorption wavelength were optimized. Relative standard deviations (RSD, 2.3-5.4%), coefficients of determination (r2 0.9994-0.9999), and detection limits (0.049-0.081 ng mL(-1)) of the proposed method were investigated under the selected conditions. The method was successfully applied to analyses of reservoir and tap water samples, and the relative recoveries of chlorophenols from the spiked reservoir and tap water samples were 94.1-100.4% and 87.8-101.2%, respectively. The proposed method is capable of identifying and quantitating each analyte to 0.5 ng mL(-1), confirming the HPLC/DAD technique to be quite robust for monitoring trace levels of chlorophenols in water samples.     

Determination of chlorophenols in water using dispersive liquid–liquid microextraction coupled with water‐in‐oil microemulsion electrokinetic chromatography in normal stacking mode

The current routes to couple dispersive liquid–liquid microextraction with capillary electrophoresis are the evaporation of water immiscible extractants and the back‐extraction of analytes. In this study, a new methodology for this combination using water‐in‐oil microemulsion electrokinetic chromatography coupled with normal stacking mode on‐line sample concentration was developed to analyze chlorophenols in water samples. The analytes were extracted with tributyl phosphate and the extractant dilution (3×) was directly injected into an electrophoresis buffer (7.7 cm) containing 5% sodium dodecyl sulfate, 78% 1‐butanol, 2% 1‐heptane, and 15% sodium acetate solution (pH 8.0). This proposed method is very simple and convenient compared to the conventional procedures. The key parameters affecting separation and concentration were systematically optimized. Under the optimized conditions, dispersive liquid–liquid microextraction contributed an enrichment factor of 45–50, and the overall sensitivity improvement was 312–418‐fold. Limits of detection between 1.4 and 3.0 ng/mL and limits of quantification between 4.5 and 10.2 ng/mL were achieved. Acceptable repeatability lower than 3.0% for migration time and 9.0% for peak areas were obtained. The developed method was successfully applied for analysis of the chlorophenols in real water samples.     

基于氨基功能化石墨烯磁性材料的磁固相萃取-高效液相色谱法分析海水中的氯酚类污染物

本文采用氨基功能化石墨烯磁性材料富集海水中的5种氯酚类(CPs)污染物,建立了一种快速、高效、灵敏的磁固相萃取-高效液相色谱(MSPE-HPLC)法,用于其残留量的测定。实验优化了磁固相萃取的条件,考察了样品pH值、富集时间和洗脱剂的种类与用量等对CPs回收率的影响。样品经富集后在C8反相液相色谱柱(250×4.6mm i.d.,5μm)上分离,以体积比为70∶30的甲醇-5mmol/L NH_4Ac溶液为流动相,紫外检测波长为230nm。结果表明,5种CPs的富集倍数可达250倍;CPs浓度在1~2 000ng/L范围内呈现良好的线性关系,线性相关系数(R)均大于0.9995;平均回收率为92.6%~101.2%,相对标准偏差为0.6%~7.2%;检出限为0.15~1.06ng/L,定量限为0.5~3.2ng/L。采用本方法对5个实际海水样品中的CPs进行了定量检测,结果其中一种样品含有2,4,6-三氯苯酚,浓度为6.5ng/L。     

Development of a static and exhaustive extraction procedure for field passive preconcentration of chlorophenols in environmental waters with hollow fiber-supported liquid membrane

A static and exhaustive extraction mode of hollow fiber-supported liquid membrane was developed for field sample passive pretreatment of environmental water samples. The extraction device was prepared by immobilizing dihexyl ether in the wall of a polypropylene hollow fiber membrane (60 cm length, 50 μm wall thickness, and 280 μm id) as liquid membrane and filling the fiber lumen with 0.1 M NaOH as acceptor, and closing the two ends of the fiber with an aluminum foil. Passive extraction was conducted by immersing the device into 15 mL water samples modified with 0.01 M HCl and 20% m/v NaCl. Model analytes including 4-chlorophenol, 2,4-dichlorophenol, and 2,4,6-trichlorophenol were transferred into acceptor with extraction efficiencies over 79% in 10 h at room temperature, and determined by high-performance liquid chromatography. The proposed method has the enrichment factor of 394-498 and LOD of 0.3-0.4 μg/L for the three chlorophenols. Humic acid and salinity in the environmentally relevant range had no significant influence on the extraction, and chlorophenols in various environmental waters were determined with spike recoveries between 71.6 and 120%. The static passive extraction nature benefited field sample pretreatment without power, whereas the exhaustive extraction mode effectively eliminated the sample matrix effects.     

Solid‐phase microextraction based on polyaniline doped with perfluorooctanesulfonic acid coupled to HPLC for the quantitative determination of chlorophenols in water samples

A porous and highly efficient polyaniline‐based solid‐phase microextraction (SPME) coating was successfully prepared by the electrochemical deposition method. A method based on headspace SPME followed by HPLC was established to rapidly determine trace chlorophenols in water samples. Influential parameters for the SPME, including extraction mode, extraction temperature and time, pH and ionic strength procedures, were investigated intensively. Under the optimized conditions, the proposed method was linear in the range of 0.5–200 μg/L for 4‐chlorophenol and 2,4,6‐trichlorophenol, 0.2–200 μg/L for 2,4‐dichlorophenol and 2–200 μg/L for 2,3,4,6‐tetrachlorophenol and pentachlorophenol, with satisfactory correlation coefficients (>0.99). RSDs were <15% (n = 5) and LODs were relatively low (0.10–0.50 μg/L). Compared to commercial 85 μm polyacrylate and 60 μm polydimethylsiloxane/divinylbenzene fibers, the homemade polyaniline fiber showed a higher extraction efficiency. The proposed method has been successfully applied to the determination of chlorophenols in water samples with satisfactory recoveries.     

High‐density extraction solvent‐based solvent de‐emulsification dispersive liquid–liquid microextraction combined with MEKC for detection of chlorophenols in water samples

For the first time, the high‐density solvent‐based solvent de‐emulsification dispersive liquid–liquid microextraction (HSD‐DLLME) was developed for the fast, simple, and efficient determination of chlorophenols in water samples followed by field‐enhanced sample injection with reverse migrating micelles in CE. The extraction of chlorophenols in the aqueous sample solution was performed in the presence of extraction solvent (chloroform) and dispersive solvent (acetone). A de‐emulsification solvent (ACN) was then injected into the aqueous solution to break up the emulsion, the obtained emulsion cleared into two phases quickly. The lower layer (chloroform) was collected and analyzed by field‐enhanced sample injection with reverse migrating micelles in CE. Several important parameters influencing the extraction efficiency of HSD‐DLLME such as the type and volume of extraction solvent, disperser solvent and de‐emulsification solvent, sample pH, extraction time as well as salting‐out effects were optimized. Under the optimized conditions, the proposed method provided a good linearity in the range of 0.02–4 μg/mL, low LODs (4 ng/mL), and good repeatability of the extractions (RSDs below 9.3%, n = 5). And enrichment factors for three phenols were 684, 797, and 233, respectively. This method was then utilized to analyze two real environmental samples from wastewater and tap water and obtained satisfactory results. The obtained results indicated that the developed method is an excellent alternative for the routine analysis in the environmental field.     

pH‐assisted homogeneous liquid–liquid microextraction using dialkylphosphoric acid as an extraction solvent for the determination of chlorophenols in water samples

In this study, a new pH‐assisted homogeneous liquid–liquid microextraction combined with HPLC with UV detection was developed for the determination of chlorophenols in water samples. In this approach, bis(2‐ethylhexyl) phosphate was used for the first time as the low‐density extraction solvent. In particular, 60 μL of bis(2‐ethylhexyl) phosphate was injected into the sample solution (5 mL) and dissolved completely in the sample solution while the pH was increased to 9. Afterwards, the pH of the sample solution was lowered to 1, and a cloudy solution was formed. At this stage, hydrophobic interactions between the analytes and the long double hydrocarbon chains of extraction solvent were expected to be the main forces driving extraction. A series of parameters that influence extraction were investigated systematically. Under the optimized conditions, the LODs and LOQs for the chlorophenols were 1.4–2.7 and 4.7–9.1 ng/mL, respectively. RSDs based on five replicate extraction of 100 ng/mL of each chlorophenols were <4.7% for intraday and 7.4% for interday precision. This method has been also successfully applied to analyze real water samples at two different spiked concentrations, and satisfactory recoveries were achieved.     

Fabrication of a novel hydrophobic/ion‐exchange mixed‐mode adsorbent for the dispersive solid‐phase extraction of chlorophenols from environmental water samples

A novel mixed‐mode adsorbent was prepared by functionalizing silica with tris(2‐aminoethyl)amine and 3‐phenoxybenzaldehyde as the main mixed‐mode scaffold due to the presence of the plentiful amino groups and benzene rings in their molecules. The adsorption mechanism was probed with acidic, natural and basic compounds, and the mixed hydrophobic and ion‐exchange interactions were found to be responsible for the adsorption of analytes. The suitability of dispersive solid‐phase extraction was demonstrated in the determination of chlorophenols in environmental water. Several parameters, including sample pH, desorption solvent, ionic strength, adsorbent dose, and extraction time were optimized. Under the optimal extraction conditions, the proposed dispersive solid‐phase extraction coupled with high‐performance liquid chromatography showed good linearity range and acceptable limits of detection (0.22∽0.54 ng/mL) for five chlorophenols. Notably, the higher extraction recoveries (88.7∽109.7%) for five chlorophenols were obtained with smaller adsorbent dose (10 mg) and shorter extraction time (15 min) compared with the reported methods. The proposed method might be potentially applied in the determination of trace chlorophenols in real water samples.     

气相色谱-质谱联用对纺织品中16种含氯酚及邻苯基苯酚、β-萘酚残留量的测定

建立了气相色谱-质谱(GC-MS)测定纺织品中16种含氯酚及邻苯基苯酚、β-萘酚残留量的方法.样品经甲醇超声提取、浓缩后,用0.1 mol/L硼砂溶液溶解,再经乙酸酐乙酰化后正己烷提取,用GC-MS测定,内标法定量.在0.025 ~1.0 mg/L范围内,方法的线性关系良好,相关系数为0.999 3 ~0.999 9,添加回收率为83% ~112%,相对标准偏差为0.26% ~8.82%.该方法简便、快速、灵敏度高,完全可满足进出口纺织品中16种含氯酚及邻苯基苯酚、β-萘酚残留量检测的要求.     

Microwave assisted headspace controlled-temperature single drop microextraction for liquid chromatographic determination of chlorophenols in aqueous samples

We report on an efficient one-step sample preconcentration technique by coupling microwave heating and cloud vapor zone (CVZ)-based headspace controlled-temperature single drop microextraction (HS-CT-SDME), and its application to headspace extraction of chlorophenols in aqueous solutions. Microwave irradiation is utilized to accelerate evaporation of analytes into the headspace sampling zone for the direct extraction of aqueous chlorophenols. A microdrop of extractant is suspended at the bottom of a bell-mouthed micropipette tip connected to a microsyringe needle. An external cooling system was adopted to control the formation of the CVZ around the SDME tip in the headspace sampling area. In the CVZ procedure, the warm headspace vapor is quickly cooled near the SDME tip, thus forming a dense cloud of analyte-water vapor; thereby enhancing the partition of the analytes into the SDME solvent. The chlorophenols are then determined by LC-UV detection. Under the optimized experimental conditions, the analytical signal is linearly related to the concentration of the chlorophenols range of 2.5–250?ng?mL^?1. The detection limits vary from 0.3 to 0.7?ng?mL^?1, and the precision (expressed as the relative standard deviation) from 3.7 to 13.3?%. The method was validated with real water samples, and the spiked recovery ranged between 92 and 103.1?% for river water, and between 85.1?% and 98.6?% for lake water. Compared to other methods, microwave assisted HS-CT-SDME is simple, rapid, sensitive, inexpensive and eco-friendly, and requires less sample and organic extractant.

Application of surfactant assisted dispersive liquid-liquid microextraction for sample preparation of chlorophenols in water samples

A simple, rapid, and efficient method, based on surfactant assisted dispersive liquid-liquid microextraction (SA-DLLME), followed by high performance liquid chromatography (HPLC) has been developed for the extraction and determination of chlorophenols as model compounds in environmental water samples. A conventional cationic surfactant called cethyltrimethyl ammonium bromide (CTAB) was used as a disperser agent in the proposed approach. Thirty-five microliter of 1-octanol as an extraction solvent was injected rapidly into 11 mL aqueous sample containing 0.09 mmol L⁻¹ of CTAB, the mixture was then shaken for 3 min to disperse the organic phase. Having the extraction procedure been completed, the mixture was centrifuged and 20 μL of collected phase was injected into HPLC for subsequent analysis. Some parameters such as the type and volume of the extraction solvent, the type and concentration of surfactant, pH, ionic strength, shaking time, extraction temperature and centrifugation time were optimized. The preconcentration factors (PFs) in a range of 187-353 were obtained under the optimum conditions. The linear range, detection limit (S/N = 3), and precision (n = 5) were 0.2-200, 0.1 μg L⁻¹, and 4.7-6.9%, respectively. Tap water, sea water and mineral water samples were successfully analyzed for the existence of chlorophenols using the proposed method.     

Field‐amplified sample injection combined with capillary electrophoresis for the simultaneous determination of five chlorophenols in water samples

A sensitive method of CZE‐ultraviolet (UV) detection based on the on‐line preconcentration strategy of field‐amplified sample injection (FASI) was developed for the simultaneous determination of five kinds of chlorophenols (CPs) namely 4‐chlorophenol (4‐CP), 2‐chlorophenol (2‐CP), 2,4‐dichlorophenol (2,4‐DCP), 2,4,6‐trichlorophenol (2,4,6‐TCP), and 2,6‐dichlorophenol (2,6‐DCP) in water samples. Several parameters affecting CZE and FASI conditions were systematically investigated. Under the optimal conditions, sensitivity enhancement factors for 4‐CP, 2‐CP, 2,4‐DCP, 2,4,6‐TCP, and 2,6‐DCP were 9, 27, 35, 43, and 43 folds, respectively, compared with the direct CZE, and the baseline separation was achieved within 5 min. Then, the developed FASI‐CZE‐UV method was applied to tap and lake water samples for the five CPs determination. The LODs (S/N = 3) were 0.0018–0.019 µg/mL and 0.0089–0.029 µg/mL in tap water and lake water, respectively. The values of LOQs in tap water (0.006–0.0074 µg/mL) were much lower than the maximum permissible concentrations of 2,4,6‐TCP, 2,4‐DCP, and 2‐CP in drinking water stipulated by World Health Organization (WHO) namely 0.3, 0.04, and 0.01 µg/mL, respectively, and thereby the method was suitable to detect the CPs according to WHO guidelines. Furthermore, the method attained high recoveries in the range of 83.0–119.0% at three spiking levels of five CPs in the two types of water samples, with relative standard deviations of 0.37–8.58%. The developed method was proved to be a simple, sensitive, highly automated, and efficient alternative to CPs determination in real water samples.     

Determination of Chlorophenols in Sewage Sludge and Soil by High-Performance Liquid Chromatography–Tandem Mass Spectrometry with Ultrasonic-Assisted and Solid-Phase Extraction

Chlorophenols are a category of toxic pollutants that are ubiquitously present in the environment. This paper presents a reliable and feasible method for the determination of five chlorophenols in sewage sludge and soil using liquid chromatography–tandem mass spectrometry (LC-MS/MS). The pretreatment involved ultrasonic-assisted extraction and solid-phase extraction purification with hydrophilic–lipophilic balance cartridges. LC-MS/MS equipped with an electrospray ionization source operated in negative mode was used for detection, and multitude reaction monitoring mode was applied for data acquisition. The pretreatment and working conditions of LC-MS/MS were optimized to achieve satisfactory results. The intra-batch accuracies were 100.5–113.4% with relative standard deviations?≤?15.6% for the chlorophenols in sewage sludge and 71.3–102.7% with relative standard deviations?≤?14.0% for those in soil. The inter-batch accuracies were 86.1–100.5% (relative standard deviations?≤?33.6%) for sewage sludge samples and 70.5–112.5% (relative standard deviations?≤?28.2%) for soil samples, respectively. This method has been applied to the determination of chlorophenols in sewage sludge of wastewater treatment plants and soil collected from Guangzhou, China. Parachlorophenol, 2,4,6-trichlorophenol, 2,3,4,6-tetrachlorophenol, and pentachlorophenol were detected in some sewage sludge samples, with concentrations from 0.51 to 13.20?ng/g. In addition, parachlorophenol, 2,3,4,6-tetrachlorophenol, and pentachlorophenol were found in all the soil samples with concentrations from 0.33 to 5.21?ng/g. The chromatographic behavior, on-filter adsorption behavior, and the relationship between optimal collision energies and degree of chlorination of the chlorophenols was investigated. This method will be conducive to environmental research focusing on pollution investigation of chlorophenols in the environment.     

Determination of chlorophenols in human urine based on the integration of on-line automated clean-up and preconcentration unit with micellar electrokinetic chromatography.

A new method was developed and validated for the determination of chlorophenols in human urine by using micellar electrokinetic chromatography (MEKC) coupled via a mechanic arm to an on-line automatic clean-up and preconcentration unit for urine samples. Separation is accomplished by using a selective buffer consisting of 15 mM borate, 25 mM phosphate and 100 mM sodium dodecyl sulfate (SDS) at pH 9.1 in addition to a positive power supply of 25 kV at 18 degrees C. The proposed capillary electrophoresis (CE) method allows the separation of 11 chlorophenols within 7 min with a reproducibility as relative standard deviation (RSD) between 2.6% and 7.2%, and limits of detection (LODs) between 0.08 and 0.46 microg/mL for all chlorophenols. Urine samples were previously hydrolyzed with 37% HCl at 80 degrees C for 60 min and then cleaned on a C-18 mini-column. Recoveries ranged from 58% to 103%. The preconcentration treatment affords limits of determination between 4 and 12 ng/mL for all chlorophenols except pentachlorophenol and 4-chlorophenol, which could not be determined. The overall analysis time, including on-line clean-up, preconcentration and electrophoretic separation is 20 min per sample.