制备方法对新型锡锆固溶催化剂结构及其选择催化一氧化氮还原性能的影响

固定SnO2含量为60％，采用不同沉淀方法和在不同沉淀条件下制备了锡锆溶体催化剂Sn0.45Zr0.55O2，考察了沉淀过程对其结构和性能的影响，控制尿素浓度为总金属离子（Sn^4 Zr^4 )浓度的20倍，采用均相沉淀法制备的锡猪固溶体Sn0.45Zr0.55O2对催化NO还原具有最高活性和较好的重复性，在350℃下最大NO转化率达到74％，XRD，Raman,XPS,BET比表面测定和孔结构分析表明，沉淀条件不同，沉淀物的成核及生长过程不同，对SnO2与ZrO2之间的固溶度，催化剂表面元素分布，比表面和孔道结构以及催化活性都有较大的影响，ZrO2在SnO2(r)晶格中较高的固溶度，Sn在催化剂表面一定程度的偏析以及催化剂较大的孔径均有利于提高对NO还原反应的催化活性。     

一氧化氮选择还原锡锆固溶体催化剂的结构特性

采用双股并流共沉淀方法制备了SnO2含量从10％至90％的锡锆体系DeNOx催化剂,用XRD、微区电子衍射、FT-Raman及FT-IR等技术深入研究了锡锆体系氧化物的结构及其随组成的变化规律.结果表明，由于Sn4＋与Zr4＋离子半径接近,SnO2与ZrO2易于形成固溶体,并随组成变化表现出不同的结构特征.纯ZrO2为单斜相,当少量Sn4＋（SnO2 ≤ 20％）进入ZrO2晶格时形成四方相富锆固溶体,Sn4＋起到稳定ZrO2四方相的作用;随着SnO2含量的增大,结构从无定形或微晶态的富锆固溶体(含SnO2 30～50％)经富锆固溶体与金红石结构的富锡固溶体在55％ SnO2含量的共存状态变化到具有金红石结构的富锡固溶体（SnO2 ≥ 60％）.FT-Raman和FT-IR光谱测试证明,Zr进入SnO2晶格使得Sn－O键的结合减弱,Sn离子上的有效正电荷减小,降低了SnO2对丙烯的燃烧能力,从而提高了对NO的还原活性.     

镧掺杂锡锆固溶体催化剂的结构及其一氧化氮选择催化还原性能

研究了La掺杂锡锆固溶体催化剂对丙烯选择还原NO的催化活性,并对催化剂结构进行了分析,探讨了La促进锡锆固溶体NO催化还原活性的原因.     

金属氧化物掺杂对锡锆固溶体催化剂的一氧化氮选择性还原性能的影响

 锡锆固溶体催化剂Sn0．55Zr0．45O2具有较好的NO选择性还原性能．本文在此基础上对其进行金属氧化物掺杂，发现用浸渍法掺入碱性金属元素Y，La，Ba和Zn以及用研磨法加入α－Mn2O3可以提高Sn0．55Zr0．45O2的NO选择性还原性能，用浸渍法掺入过渡金属元素Ce，Ag，Cu，Mn及Ni降低了母体催化剂的活性，而浸渍硫酸镓由于在表面引入B酸位使催化剂严重积碳而大大降低了催化剂的NO选择性还原性能．文中给出了活性改善体系的最佳掺杂量，并测定了其抗水性能．在反应气中不含水的条件下，添加2％Ba的样品活性最高，而掺杂1％Zn样品具有最好的抗水性能．对丙烯氧化反应和NO氧化反应的研究表明，抑制还原剂 丙烯的完全燃烧或促进NO氧化为NO2可能有利于NO选择性还原反应的进行．     

CeO2-ZrO2复合氧化物对金属蜂窝整体催化剂性能的影响

 用浸渍法制备了不同比例的CeO2－ZrO2复合氧化物，并用XRD，H2－TPR和BET等研究了复合氧化物的晶相、还原性能及热稳定性．结果表明，所制备的CeO2－ZrO2复合氧化物形成了固溶体，Ce0．6Zr0．4O2比Ce0．90Zr0．10O2更容易被H2还原；1100℃老化后，晶胞参数无明显变化，比表面积仍有11．8m2／g．模拟二冲程摩托车尾气组成，对用贵金属Pt，Pd，Rh与CeO2及CeO2－ZrO2固溶体所制备的催化剂进行了活性评价．结果显示，1100℃老化后，催化剂仍具有很高的氧化活性．在贫氧区，Pt－Pd－Rh／Ce0．6Zr0．4O2－Al2O3对碳氢化合物氧化的催化活性则有一定的优势，是一种具有较高热稳定性的催化剂．     

CO为还原剂同时还原SO2和NO的SnO2-TiO2固溶体催化剂 I．催化剂的催化性能

采用共沉淀法制备了不同SnO2含量的SnO2-TiO2固溶体催化剂．发现该催化剂对以CO为还原剂同时还原SO2和NO生成S和N2的反应具有高活性和高稳定性．SnO2含量为50％(摩尔分数)的样品活性最高，在350℃，0．0525％s0，，0．052％NO，0.208％CO和空速3000h^-1的条件下，NO转化率接近100％，SO2转化率为88％，S和N2的选择性都接近100％，反应过程中没有剧毒气体COS生成．对于SO2 CO反应，该样品也显示了极高的活性，在350℃，0.105％SO2，0.208％CO和空速3000h^-1的条件下，SO，转化率达98％，S的选择性近100％．但该催化剂对NO CO反应的催化活性不高，在350℃，0.1025％ NO，0.208％C0，空速3000h^-1的条件下，NO的转化率仅为50％．上述结果表明，SO2对NO CO反应具有促进作用．单独的SnO2或TiO2对SO2 CO，N0 CO或SO2 NO CO反应的催化活性都很低，但SnO2和Ti02形成SnO2-TiO2固溶体后催化活性显著增大，说明SnO2和TiO2之间产生了协同效应．     

SnO2—Al2O3复合氧化物催化剂的一氧化氮选择催化还原性能

采用双股并流共沉淀方法制备的锡铝复合氧化物,对有氧条件C3H6选择还原NO反应有较高的催化活性和较宽的反应温度区间。具有最佳配比（Sn:Al(摩尔比）＝1：1.94）的锡铝复合氧化物样品,在反应温度350℃时可使NO转化率达71％,XRD、H2－TPR及NH3－TPD的研究结果表明,锡与铝难以形成氧化物固溶体, 而SnO2是以微晶形态分散于无定形的Al2O3上,Al2O3的中等强度酸性与SnO2微晶适度的氧化还原性能相结合,使锡铝复合氧化物具有较高的催化活性。     

甲烷催化燃烧催化剂Ag/SnO2体系的研究

考察了Ag/SnO2系列催化剂对甲烷燃烧反应的催化活性,并采用XRD、BET、XPS、TEM和TPR等技术对催化剂中银的存在状态进行了表征.结果表明, Ag/SnO2体系具有较高的甲烷催化燃烧活性,样品的载银量不同,银物种的存在状态及样品的比表面和催化性能也很不相同. Ag/Sn原子比低于0.20的样品中,银物种为分散态氧化银及晶相氧化银,这些样品具有较高的比表面和催化活性;载银量继续增加时,金属银开始出现并成为主要的银物种,样品的比表面和催化活性也随之迅速下降. Ag/Sn原子比为0.20的样品具有最高的催化活性.     

负载Pd密偶催化剂的载体效应

采用尿素水解法或吸附沉淀法制备了金属氧化物载体,并用浸渍法负载0.5%Pd制得了Pd/Sn0.4Zr0.6O2,Pd/ZrO2,Pd/SnO2,Pd/SnO2-Al2O3和Pd/Al2O3催化剂.采用原位漫反射红外光谱、拉曼光谱、X射线光电子能谱和程序升温还原等方法对催化剂结构进行了表征,探讨了不同载体对表面PdOx物种化学吸附性质和氧化还原性能的影响,并与样品的丙烷氧化活性相关联.漫反射红外光谱表明,在Pd/SnO2-Al2O3中,Sn对Al2O3表面的Pd原子簇起到稀释作用,促进了Pd的分散,使得其CO线式吸附强度明显高于Pd/Al2O3,但Pd过高的分散度不仅减少了表面Pd-PdO活性位对的数目,而且使反应中间物种Pd-OH之间脱水困难,因而阻塞了活性位,降低了其循环氧化还原活性;而在Sn0.4Zr0.6O2复合氧化物载体中,SnO2有效地阻止了四方晶相ZrO2向稳态单斜晶相转变,且复合载体的比表面积较ZrO2和SnO2有所增加,其表面PdOx物种的分散度适中.此外,Sn0.4Zr0.6O2复合氧化物负载的Pd的价态介于Pd0与Pd2 之间,表面氧空位较多,促进了丙烷中C-H键的活化,使比表面积较低的Pd/Sn0.4Zr0.6O2具有最好的催化丙烷氧化能力,相反比表面积较高的Pd/SnO2-Al2O3活性很差,说明分散度适中且具有较低氧化态的PdOx(0相似文献   

一锅法合成Ce_xZr_(1-x)O_2固溶体催化剂用于热化学循环分解CO_2制CO

采用一锅蒸发诱导自组装法(EISA)制备了一系列不同铈锆物质的量比的铈锆固溶体催化剂,用TGA研究了其热化学循环分解CO_2制CO的催化性能,并采用XRD、Raman光谱、H2-TPR、XPS、SEM和N_2吸附-脱附等手段对催化剂的物相结构、还原性能和表面化学性质进行了表征分析,用热重分析(TGA)研究了铈锆固溶体对热化学循环分解CO_2制CO的催化性能。结果表明,随着Ce/Zr物质的量比增加,铈锆固溶体催化剂的CO_2高温分解活性先增大后减小。Ce/Zr物质的量比为1的Ce_(0.5)Zr_(0.5)O_2催化剂由于具有较多的晶格缺陷和氧空穴,氧迁移能力强,催化活性高,而Ce/Zr物质的量比为3的Ce_(0.75)Zr_(0.25)O_2催化剂具有相对稳定的氧空穴数,循环稳定性好。循环反应后,所有的催化剂均出现了一定程度的烧结,且富锆固溶体发生了相分离,这可能会影响催化剂的性能。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Thermodynamics of the formation of oxosulfides of rare-earth elements

The enthalpies of solution of several oxosulfides of rare-earth elements and the high-temperature enthalpies of oxosulfides and oxosulfates of lanthanum and yttrium were measured using solution calorimetry and high-temperature microcalorimetry techniques. Standard enthalpies of formation and some thermodynamic properties of oxosulfides and oxosulfates were calculated. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2 pp. 294–297, February, 1997.     

探究“铁的锈蚀条件”实验创新设计

设计了铁的锈蚀实验,说明了铁钉的处理方法,增加了温度、酸、碱的影响条件,实现了铁跟蒸馏水及空气中氧气快速反应而生锈,使实验在5 min左右就能够得到准确的结果。