Temporal variation of atmospheric polycyclic aromatic hydrocarbon concentrations in PM10 from the Kathmandu Valley and their gas-particle concentrations in winter

The concentrations of polycyclic aromatic hydrocarbons (PAHs) in particulate matter (PM) with a diameter <10 µm (PM₁₀, 50% cut off) were investigated in the Kathmandu Valley, Nepal, during 2003. In order to understand the dynamics of atmospheric PAHs in winter, the PAH concentrations in total PM and in the gaseous phase were investigated in the valley in December 2005. Total of 45 PAH compounds (∑45PAHs) were analysed by high-resolution gas chromatography/high-resolution mass spectrometry (HRGC/HRMS). In 2003, the ∑45PAH concentrations in PM₁₀ ranged between 4.3 and 89 ng m^?3 (annual average; 27 ± 24 ng m^?3). The average concentrations of ∑45PAHs in December 2005 were 210 ± 33 ng m^?3 in total PM and 430 ± 90 ng m^?3 in the gaseous phase. The ∑45PAH concentration in PM accounted for more than 30% of the sum of their particulate and gaseous forms. Phenanthrene (Ph) was the most predominant compound in the gaseous phase, whereas four- to seven-ring PAHs were predominant in total PM. The highest values of ∑45PAHs occurred in the winter and spring. Estimates of emission sources based on diagnostic molecular ratios showed that atmospheric PAHs in the Kathmandu Valley mainly originated from the exhaust gas of diesel engine. In the winter and spring, PAH pollution would be accelerated by the operations of brick kilns and the frequent formation of an atmospherically stable layer in the valley.     

Pollution characteristics of ambient PM2.5-bound PAHs and NPAHs in a typical winter time period in Taiyuan

The pollution characteristics of ambient fine particulate matter（PM2.5） containing polycyclic aromatic hydrocarbons（PAHs） and nitrated PAHs（NPAHs） in samples collected during a typical winter time period in Taiyuan of China were investigated.The obtained results revealed that the mean mass concentrations of PM2.5,SPAHs（sum of 16 PAHs） and SNPAHs（sum of 3 NPAHs） on PM2.5were161.4 mg/m3,119.8 ng/m3and 0.446 ng/m3,respectively.Diagnostic ratios of PAHs and NPAHs implied that coal consumption might be the main source of the PM2.5pollution.The measured PM2.5mass concentrations,BaP equivalent toxicity（28.632 ng/m3） and individual carcinogenicity index（3.14 10 5） were much higher than those of the recommended safety standards.     

Analysis of polycyclic aromatic hydrocarbons in atmospheric particulate samples by microwave‐assisted extraction and liquid chromatography

A methodology based on microwave‐assisted extraction (MAE) and LC with fluorescence detection (FLD) was investigated for the efficient determination of 15 polycyclic aromatic hydrocarbons (PAHs) regarded as priority pollutants by the US Environmental Protection Agency and dibenzo(a,l)pyrene in atmospheric particulate samples. PAHs were successfully extracted from real outdoor particulate matter (PM) samples with recoveries ranging from 81.4 ± 8.8 to 112.0 ± 1.1%, for all the compounds except for naphthalene (62.3 ± 18.0%) and anthracene (67.3 ± 5.7%), under the optimum MAE conditions (30.0 mL of ACN for 20 min at 110°C). No clean‐up steps were necessary prior to LC analysis. LOQs ranging from 0.0054 ng/m³ for benzo(a)anthracene to 0.089 ng/m³ for naphthalene were reached. The validated MAE methodology was applied to the determination of PAHs from a set of real world PM samples collected in Oporto (north of Portugal). The sum of particulate‐bound PAHs in outdoor PM ranged from 2.5 and 28 ng/m³.     

大体积搅拌棒吸附萃取技术与热脱附-气相色谱-质谱法测定地表水中多环芳烃

基于搅拌棒吸附萃取(SBSE)技术建立了气相色谱-质谱测定地表水中16种多环芳烃(PAHs)的分析方法。该法采用多搅拌吸附棒同时富集,依次热脱附冷聚焦后进样的方式有效解决了搅拌棒吸附时间长、富集水样体积小等问题。优化后的结果表明,在0.2~10 ng/L范围内(萘为0.5~10 ng/L范围),16种PAHs的线性关系良好,相关系数(r)均0.99,方法检出限(MDL)为0.03~0.20 ng/L(萘为0.50 ng/L)。用该方法对钱塘江流域地表水进行测定,共检测出11种PAHs,含量为0.13~1.57 ng/L,不同添加水平下的加标回收率为75.6%~108.9%。该法可应用于地表水样品中该类物质的超痕量检测。     

Analysis of 27 polycyclic aromatic hydrocarbons by matrix solid-phase dispersion and isotope dilution gas chromatography-mass spectrometry in sewage sludge from the Spanish area of Madrid

A method for the determination of 27 polycyclic aromatic hydrocarbons (PAHs) in sludge from wastewater treatment plants (WWTPs) located in urban, industrial or rural zones is presented. PAHs were extracted by matrix solid-phase dispersion (MSPD) assisted by sonication. Purification of extracts was carried out by solid-phase extraction with C(18) and PAHs were eluted with acetonitrile. PAHs were determined by isotope dilution gas chromatography with electron impact mass spectrometric detection in the selected ion-monitoring mode (GC-MS-SIM), using deuterated PAHs as internal standards. The limits of detection ranged from 0.03 ng/g for acenaphthylene to 0.45 ng/g for benzo[b]naphtho[2,1-d]thyophene. After optimization, the method was validated with a certified reference sludge. The proposed analytical method was applied to determine PAH levels in sewage sludge samples collected from 19 water treatment plants located in the province of Madrid (Spain). In most of the examined samples, phenanthrene was the main compound with a mean concentration of 1062 ng/g. PAHs were detected in all of the samples, with total concentrations between 390 and 6390 ng/g dry weight for the 27 PAHs analyzed and from 310 to 5120 ng/g dry weight for the sum of the 10 PAHs considered in the draft European Union directive.     

快速溶剂提取-高效液相色谱法测定PM2.5中16种多环芳烃

建立大气细颗粒物(PM2.5)中16种多环芳烃(PAHs)的快速溶剂提取-直接进样-高效液相色谱测定方法.PM2.5经玻璃纤维滤膜收集,采样后的滤膜直接用乙腈经快速溶剂萃取仪提取,以乙腈和水作为流动相,提取液通过ZORBAX Eclipse PAH液相色谱柱分离,紫外串联荧光检测器检测.16种PAHs分离效果良好,在0.025~5.000μg/mL范围内线性相关系数r≥0.9998,方法加标回收率为78.3%~113.2%,相对标准偏差为0.5%~9.5%,检出限为0.007~0.062 ng/m3.本方法操作简便、快速、准确、灵敏,适于PM2.5中16种PAHs的同时测定.     

Optimization and validation of a low temperature microwave-assisted extraction method for analysis of polycyclic aromatic hydrocarbons in airborne particulate matter

A low temperature microwave-assisted extraction method (MAE) is reported for the analysis of polycyclic aromatic hydrocarbons (PAHs) in airborne particulate matter (PM). The main parameters affecting the extraction efficiency (choice of extractants, microwave power, and extraction time) were investigated and optimized. The optimized procedure requires a 20 ml mixture of acetone:n-hexane (1:1) for extraction of PAHs in PM at 150 W of microwave energy (20 min extraction time). Clean-up of MAE extracts was not found to be necessary. The optimized method was validated using two different SRM (1648-urban particulate matter and 1649a, urban dust). The results obtained are in good agreement with certified values. PAHs recoveries for both reference materials were between 79 and 122% with relative standard deviation ranging from 3 to 21%. Detection limits were determined based on blank determination using two kinds of quartz filter substrates (n = 10), which ranged from 0.001 (0.03) ng m⁻³ (pg/μg) for B(k)Ft to 1.119 (37.3) for Naph in ng m⁻³ (pg/μg), respectively. The repeatability and day-to-day reproducibility obtained in this study were in the range of 4-16 and 3-25% for spiked standards and SRM 1649, respectively. The optimized and validated MAE technique was applied to the extraction of PAHs from a set of real world PM samples collected in Singapore. The sum of particulate-bound PAHs in outdoor PM ranged from 1.05 to 3.45 ng m⁻³ while that in indoor PM (cooking emissions) ranged from 27.6 to 75.7 ng m⁻³, respectively.     

加速溶剂萃取/气相色谱-质谱测定海洋沉积物中的痕量多环芳烃

沉积物是多环芳烃(polycyclic aromatic hydrocarbons,PAHs)在环境中迁移归趋的一个重要的汇[1]。沉积物中多环芳烃的提取方法主要有索氏提取、超声波提取、微波萃取、加速溶剂提取及超临界流体萃取等。其中加速溶剂提取(accelerated solvent extraction,ASE)由于提取速度快,溶     

Particulate matter, gas-phase and particle-bound polycyclic aromatic hydrocarbons in an urban environment heavily impacted by vehicular traffic (Bologna, Italy)

A set of 8 polycyclic aromatic hydrocarbons (PAHs) has been analysed in a traffic-limited area in Bologna downtown, both in the gas-phase and in the particulate phase (PM10), and gas-to-particle partitioning has been investigated. From Sep 2002 to May 2003, 28 high volume PM10 samplings were carried out, and in 50 % of the samplings, PM10 concentrations exceeded the limit of 50 microg/m3 established by a 1999 EU directive. A precisely defined sampling strategy was adopted to limit artifacts (8 h sampling in the same time interval) in the 28 samplings carried out in different meteorological conditions. A linear log-log correlation was found between gas-particle partitioning coefficients KBp and the subcooled liquid vapour pressures pB0LB, with rP2P = 0.82 and slope = -0.59. This empirical correlation may be used to anticipate the total (gas + particle-bound) concentration of each PAHs in this urban site, once PM10 and the particle-bound concentration is measured. Parallel samplings of PM10 and of PM2.5 allowed us to ascertain that PM2.5 represents the gross contribution to PM10 and that most of the particle-bound PAHs reside on the finest fraction of particulate matter.     

Sensitive determination of polycyclic aromatic hydrocarbons in water samples using monolithic capillary solid-phase extraction and on-line thermal desorption prior to gas chromatography-mass spectrometry

A methacrylate-based monolithic capillary column has been evaluated for the preconcentration of polycyclic aromatic hydrocarbons (PAHs) from environmental water samples. For this purpose, the monolyte was in situ synthesized in a 6cm×0.32mm id fused-silica capillary. The microextraction unit was fitted to a micro-HPLC pump to pass 10mL of sample. The isolated pollutants were eluted by means of 10μL of methanol, the organic phase being directly collected in a specific interface that can be fitted to the injection port of the gas chromatograph without modification. The interface allows the on-line thermal desorption of the PAHs, avoiding the dilution and providing enough sensitivity to reach the legal limits established for these pollutants in the matrices selected. The limits of detection achieved for 10mL of water ranged between 2.8ng/L (indeno(1,2,3-cd)pyrene) and 11.5ng/L (acenaphthene) with acceptable precision (between 4.5 and 18.2% RSD). The method was applied to the determination of the selected PAHs in tap, river waters and sewage, being fluoranthene and pyrene detected in all of them at concentrations lower than the legal limits established for these compounds in the matrices assayed.     

An experimental design approach to optimise the determination of polycyclic aromatic hydrocarbons from rainfall water using stir bar sorptive extraction and high performance liquid chromatography-fluorescence detection

Stir bar sorptive extraction (SBSE) followed by HPLC-fluorescence detection (FLD) was optimised for analysing 15 polycyclic aromatic hydrocarbons (PAHs) from water samples, especially rainfall water with low PAH content. The literature data described widely different experimental conditions for the extraction of PAHs by SBSE. A chemometric approach was therefore used to evaluate the statistically influential and/or interacting factors, among those described in the literature, and to find the best extraction and desorption conditions. Among six factors studied in a 2(6-2) fractional factorial design, only sample volume, extraction time and the interaction between both of them had significant effects on the PAH extraction recoveries. Optimal sample volume of 10 mL and extraction time of 140 min were obtained with a response surface design. For the desorption conditions, a Box-Behnken design showed that desorption time, temperature and PAH concentrations had significant effects. The best conditions were two successive desorptions with 100 microL of acetonitrile for 25 min at 50 degrees C. The optimised method was repeatable (RSD< or =5.3% for 50 ng L(-1) spiked water and < or =12.8% for 5 ng L(-1) spiked water), linear (R(2)> or =0.9956), with quantitative absolute recoveries (> or =87.8% for 50 ng L(-1) spiked water), and with the LOD between 0.2 and 1.5 ng L(-1). The optimised method was successfully applied to six-rainfall water samples collected in a suburban area. The total PAHs concentrations studied ranged from 31 to 105.1 ng L(-1). Seasonal variation was observed and on average three PAHs were at the highest concentrations (phenanthrene, fluoranthene and pyrene).     

应用搅拌棒吸附萃取-热脱附-气相色谱/质谱法快速测定滇池水系中的16种多环芳烃

应用搅拌棒吸附萃取(SBSE)-热脱附(TDS)-气相色谱/质谱联用(GC/MS)方法测定了滇池水系(滇池和盘龙江上、中、下游)中16种多环芳烃(PAHs)的含量。方法快速简便,无有机溶剂污染,PAHs的最低检出限为1.0~468.8 pg,理论回收率在90%以上,加标回收率为83.1%~109.4%,相对标准偏差小于10%。测定结果表明,这16种多环芳烃在滇池水样中的含量为89.16 ng/L,在盘龙江上游水样中的含量为65.41 ng/L,在盘龙江中游水样中的含量为339.22 ng/L,而在盘龙江下游水样中的含量为62.25 ng/L,说明滇池水系已经受到一定的PAHs污染,加强对滇池、盘龙江中PAHs有机污染的控制势在必行。     

Analysis of polycyclic aromatic hydrocarbons in fish: evaluation of a quick,easy, cheap,effective, rugged,and safe extraction method

QuEChERS method was evaluated for extraction of 16 PAHs from fish samples. For a selective measurement of the compounds, extracts were analysed by LC with fluorescence detection. The overall analytical procedure was validated by systematic recovery experiments at three levels and by using the standard reference material SRM 2977 (mussel tissue). The targeted contaminants, except naphthalene and acenaphthene, were successfully extracted from SRM 2977 with recoveries ranging from 63.5–110.0% with variation coefficients not exceeding 8%. The optimum QuEChERS conditions were the following: 5 g of homogenised fish sample, 10 mL of ACN, agitation performed by vortex during 3 min. Quantification limits ranging from 0.12–1.90 ng/g wet weight (0.30–4.70 μg/L) were obtained. The optimized methodology was applied to assess the safety concerning PAHs contents of horse mackerel (Trachurus trachurus), chub mackerel (Scomber japonicus), sardine (Sardina pilchardus) and farmed seabass (Dicentrarchus labrax). Although benzo(a)pyrene, the marker used for evaluating the carcinogenic risk of PAHs in food, was not detected in the analysed samples (89 individuals corresponding to 27 homogenized samples), the overall mean concentration ranged from 2.52 ± 1.20 ng/g in horse mackerel to 14.6 ± 2.8 ng/g in farmed seabass. Significant differences were found between the mean PAHs concentrations of the four groups.     

Development of a liquid chromatography/tandem mass spectrometry assay for the quantification of PM00104, a novel antineoplastic agent, in mouse, rat, dog, and human plasma

A rapid and sensitive liquid chromatography/tandem mass spectrometry (LC/MS/MS) assay was developed and validated to quantify a novel antineoplastic agent, PM00104, in mouse, rat, dog, and human plasma. The method was validated to demonstrate the specificity, limit of quantification (LOQ), accuracy, and precision of measurements. The calibration range for PM00104 was established using PM00104 standards from 0.01-5.0 ng/mL in blank plasma. The selected reaction monitoring (SRM), based on the m/z 692.2 --> 218.2 transition, was specific for PM00104, and that based on the m/z 697.2 --> 218.2 transition was specific for PM00104 ((13)C(2),(2)H(3)) (the internal standard, IS); no endogenous materials interfered with the analysis of PM00104 and IS from blank plasma. The assay was linear over the concentration range 0.01-5.0 ng/mL. The correlation coefficients for the calibration curves ranged from 0.9981-0.9999. The mean intra-day and inter-day accuracies for all calibration standards (n = 8) ranged from 97-105% (< or =5% bias) in human plasma, and the mean inter-day precision for all calibration standards was less than 8.5%. The mean intra- and inter-day assay accuracy for all quality control (QC) replicates in human plasma (n = 9), determined at each QC level throughout the validated runs, ranged from 96-112% (< or =12% bias) and from 102-105% (< or =5% bias), respectively. The mean intra- and inter-day assay precision was less than 15.0 and 11.8% for all QC levels, respectively. For the QC samples prepared in animal species plasma, the %CV values of the assays ranged from 1.8-8.8% in mouse plasma, from 3.7-13.8% in rat plasma, and from 3.0-7.2% in dog plasma. The assay accuracies ranged from 92-102% (< or =8% bias) for all QC levels prepared in mouse plasma; ranged from 93-106% (< or =7% bias) in rat plasma; and ranged from 95-114% (< or =14% bias) in dog plasma. The assay has been used to support preclinical pharmacokinetic and toxicokinetic studies and is currently used to measure PM00104 plasma concentrations to support clinical trials.     

超声提取-气相色谱-质谱法测定本草香中16种颗粒态多环芳烃含量及其排放特征分析

本草香颗粒态多环芳烃(PAHs)的分析对探究人体健康和环境安全的影响具有重要意义,但目前相关研究主要针对竹签香,对于配方更为复杂、日常使用更为频繁的本草香颗粒态PAHs定量分析研究十分有限且缺少针对性。为了研究本草香颗粒态PAHs的排放因子和排放特征,在自制的试验舱内采集5种本草香燃烧后的颗粒物,通过优化萃取溶剂、超声时间和仪器分析条件,建立了超声提取-气相色谱-质谱(GC-MS)测定本草香燃烧后颗粒物上所吸附的16种PAHs的方法。通过采集0.8 g样品,切取整片滤膜样品,使用正己烷-二氯甲烷(1∶1, v/v)进行超声萃取,经浓缩定容过滤后使用气相色谱-质谱分析,内标法定量。结果表明,16种PAHs在0.1~5.0 μg/mL范围内线性良好(相关系数r²>0.998),方法检出限(MDL)为0.4~3.8 ng/g;低、高2个水平的加标回收率分别为77.4%~99.5%和82.0%~101.3%;相对标准偏差(RSD)为0.7%~7.2%。5种本草香颗粒态PAHs的排放因子为4.60~11.89 μg/g。本草香的16种颗粒态PAHs中菲(Phe)的含量均为最高,所占比例为24.85%~42.59%,其次为荧蒽(Flu)、芘(Pyr)、 \stackrel{艹}{屈} (Chr)、蒽(Ant)。本草香颗粒态PAHs中Phe的含量稳定且占比明显高于其他室内燃烧源,可将Phe作为本草香的颗粒态特征PAHs。颗粒态PAHs主要分布在3环和4环上,3环和4环PAHs占比之和为83.84%~96.31%。颗粒态的Phe/Flu比值可作为辨别不同室内燃烧源中燃香释放源的特征比值。该方法所需样品量少,灵敏度高,前处理操作简便,适用于燃香类产品中PAHs的快速检测,同时为了解本草香颗粒态PAHs分布规律和健康危害提供科学数据。     

ASE-SPE/GC-MS测定土壤中16种PAHs质量控制研究

优化了土壤中16种优控多环芳烃( PAHs)的分析方法,建立了一套完备的质量控制体系,解决了PAHs分析中常见的技术难点,如苯并(a)芘(BaP)回收率低,基质复杂的样品净化效果不理想,萘(Nap)和菲(Phe)挥发损失和环境本底影响等.样品经加速溶剂提取(ASE),固相萃取(SPE)净化,逐级减压浓缩,气相色谱质谱( GC - MS)测定,并以氘代苯并a芘(BaP - d12)作回收率指示物.实验比较了3种正相SPE吸附剂的效果,发现弗罗里硅土对BaP存在明显的降解现象,BaP的定量应使用同位素稀释法,以降低其分析不确定度;氧化铝对PAHs的吸附性过强,不利于样品净化;硅胶最为理想.PAHs的仪器检出限为0.26～5.7 pg,方法检出限为0.067 ～0.97 ng/g(干重),土壤基质加标回收率为71％～ 122％,相对标准偏差为1.6％～8.3％.将该法用于7个电子废物焚烧区域农田土壤样品的测定,PAHs含量在28～ 283 ng/g(干重)之间,样品中BaP-d12的回收率为90％～124％,各项质控指标符合检测要求.     

Magnetic solid‐phase extraction of polycyclic aromatic hydrocarbons in water samples by Fe3O4@polypyrrole/carbon nanotubes

A magnetic solid‐phase extraction method coupled with gas chromatography was proposed for the determination of polycyclic aromatic hydrocarbons in the environmental water samples. The magnetic adsorbent was prepared by incorporating Fe₃O₄ nanoparticles, multi‐walled carbon nanotubes, and polypyrrole. The main factors affecting the extraction efficiency including the amount of the sorbents, desorption conditions, extraction time, salt concentration, and sample solution pH were investigated and optimized. Under the optimum conditions, good linearity was obtained within the range of 0.03?100 ng/mL for all analytes, with correlation coefficients ranging from 0.9942 to 0.9973. The method detection limits (S/N = 3) were in the range of 0.01–0.04 ng/mL and the limits of quantification (S/N = 10) were 0.03–0.1 ng/mL. Repeatability of the method was assessed through five consecutive extractions of independently prepared solutions at concentrations of 0.1, 10, and 100 ng/mL of the compounds. The observed repeatability ranged 3.4–10.9% depending of the compound considered. The proposed method was successfully applied in the analysis of PAHs in environmental samples (tap, well, river, and wastewater). The recoveries of the method ranged between 93.4 and 99.0%. The procedure proved to be efficient and environmentally friendly.     

Determination of semi-volatile priority pollutants in landfill leachates and sediments using microwave-assisted headspace solid-phase microextraction

The present work was focused on the development of a simple method aimed at the determination of 12 polycyclic aromatic hydrocarbons (PAHs) and 15 polychlorinated biphenyls (PCBs) in landfill leachates and sediments by adapting a domestic microwave oven to perform microwave-assisted headspace solid-phase microextraction (MA-HS-SPME) followed by gas chromatographic separation and tandem mass spectrometric detection. Good linearity was observed within the concentration range studied; detection limits ranged from 0.1 ng/l to 7 ng/l for PCBs and from 5 ng/l to 926 ng/l for PAHs. Concerning precision, the relative standard deviations obtained were, on average for the leachate and sediment samples analysed, 18% for PCBs and 20% for PAHs. Average recovery values were 37% and 76% for PCBs, and 58% and 48% for PAHs, respectively, for the leachate and reference sediment studied. The method allows the determination of PAHs and PCBs in landfill leachates and sediments, avoiding clean-up steps and the consumption of organic solvents.     

Analysis of polycyclic aromatic hydrocarbons by liquid chromatography/tandem mass spectrometry using atmospheric pressure chemical ionization or electrospray ionization with tropylium post-column derivatization

Polycyclic aromatic hydrocarbons (PAHs) with four to six rings are potent carcinogens. This study analyzed ten of the sixteen US EPA priority PAHs using reversed-phase liquid chromatography/tandem mass spectrometry (LC/MS/MS) in selected reaction monitoring mode with two ionization sources: positive atmospheric pressure chemical ionization (APCI+) or positive elecrtrospray ionization (ESI+) with tropylium post-column derivatization. Several factors were investigated, including mobile phases, stationary phases of columns and chromatographic temperature, to determine how optimal separation and sensitivity might be achieved. Methanol used as an organic mobile phase provided better sensitivities for most PAHs than acetonitrile, although some PAHs co-eluted. Acidic buffers did not increase analyte signals. Use of Restek Pinnacle II PAH columns (250 x 4.6 mm or 250 x 2.1 mm, 5 microm) with water/acetonitrile gradient at 27 degrees C made possible a good separation of the ten analytes. [M]+. were the best precursor ions in both APCI and ESI, although fluoranthene could not be detected in ESI mode when tropylium post-column derivatization was performed. [M-28]+ and [M-52]+ were the major product ions of PAHs after collision-induced dissociation, a result of neutral losses of C(2)H(4) and (C(2)H(2))(2), respectively. Chromatographic separation for PAH isomers was crucial because the mass spectra were so similar that even MS/MS could not distinguish them from each other. The recoveries of sample preparations of PAHs spiked onto air-sampling filters ranged between 77.5 and 106% with relative standard deviations between 1.1 and 15.9%. This method was validated by analyzing NIST SRM 1649a (urban dust), producing results comparable with the certified PAH concentrations. The detection limits using APCI and ESI interfaces, defined as three times the noise levels, ranged between 0.23 and 0.83 ng and between 0.16 and 0.84 ng of on-column injection, respectively.     

Concentration profiles of cocaine, pyrolytic methyl ecgonidine and thirteen metabolites in human blood and urine: determination by gas chromatography-mass spectrometry

When cocaine is smoked, a pyrolytic product, methyl ecgonidine (anhydroecgonine methyl ester), is also consumed with the cocaine. The amount of methyl ecgonidine formed depends on the pyrolytic conditions and composition of the illicit cocaine. This procedure describes detection of cocaine and 10 metabolites--cocaethylene, nor-cocaine, nor-cocaethylene, methyl ecgonine, ethyl ecgonine, benzoylecgonine, nor-benzoylecgonine, m-hydroxybenzoylecgonine, p-hydroxybenzoylecgonine and ecgonine--in blood and urine. In addition, the detection of pyrolytic methyl ecgonidine and three metabolites--ecgonidine (anhydroecgonine), ethyl ecgonidine (anhydroecgonine ethyl ester) and nor-ecgonidine (nor-anhydroecgonine)--are included. The newly described metabolites, ethyl ecgonidine and nor-ecgonidine, were synthesized and characterized by gas chromatography-mass spectrometry (GC-MS). All 15 compounds were extracted from 3 mL of blood or urine by solid-phase extraction and identified by a GC-MS method. The overall recoveries were 49% for methyl ecgonine, 35% for ethyl ecgonine, 29% for ecgonine and more than 83% for all other drugs. The limits of detection were between 0.5 and 4.0 ng/mL except for ecgonine, which was 16 ng/mL. Linearity for each analyte was established and in all cases correlation coefficients were 0.9985-1.0000. The procedure was applied to examine the concentration profiles of analytes of interest in post-mortem (PM) blood and urine, and in urine collected from living individuals (LV). These specimens previously were shown to be positive for the cocaine metabolite, benzoylecgonine. Ecgonidine, the major metabolite of methyl ecgonidine, was present in 77% of PM and 88% of the LV specimens, indicating smoking as the major route of cocaine administration. The new pyrolytic metabolites, ethyl ecgonidine and nor-ecgonidine, were present in smaller amounts. The urine concentrations of nor-ecgonidine were 0-163 ng/mL in LV and 0-75 ng/mL in PM specimens. Ethyl ecgonidine was found only in PM urine at concentrations 0-39 ng/mL. Ethanol-related cocaine metabolites, ethyl ecgonine or cocaethylene, were present in 69% of PM and 53% of cocaine-positive LV specimens, implying alcohol consumption with cocaine use. The four major metabolites of cocaine--benzoylecgonine, ecgonine, nor-benzoylecgonine and methyl ecgonine--constituted approximately 88 and 97% of all metabolites in PM and LV specimens, respectively. The concentrations of nor-cocaine and nor-cocaethylene were consistently the lowest of all cocaine metabolites. At benzoylecgonine concentrations below 100 ng/mL, ecgonine was present at the highest concentrations. In 20 urine specimens, benzoylecgonine and ecgonine median concentrations (range) were 54 (0-47) and 418 ng/mL (95-684), respectively. Therefore, detection of ecgonine is advantageous when benzoylecgonine concentrations are below 100 ng/mL.