Effect of ultrasound agitation on the release of heavy elements in Certified Reference Material of human hair (CRM BCR 397)

An ultrasonic-assisted leaching procedure was developed for the determination of heavy elements (As, Cu, Cd, Pb, and Zn) in Certified Reference Material of human hair (CRM 397) provided from the Community Bureau of Reference (BCR) of the Commission of the European Community. Concentrated nitric acid-30% hydrogen peroxide (2 + 1) was used for the leaching method. The effects of different factors on acid leaching of elements, such as presonication time (without ultrasonic stirring), sonication or exposure time to ultrasound, and temperature of the ultrasonic bath have been investigated. Optimum values of these parameters were selected for the maximum extraction of heavy metals from CRM BCR 397 and human scalp hair samples of normal healthy males. To check the validity of the proposed method, a wet acid digestion method was used to obtain the total elemental concentration in CRM BCR 397 and scalp hair samples. Cu and Zn in leachate and digests were measured by flame atomic absorption spectrometry using a conventional air/acetylene flame, while As, Cd, and Pd were determined by electrothermal atomic absorption spectrometry. Under optimized conditions, the recovery for Zn, Cd, Pd, As, and Cu was 98, 98.5, 97.5, 98.2, and 95%, respectively, of those obtained with the wet acid digestion method.     

Determination of cadmium and lead in table salt by sequential multi-element flame atomic absorption spectrometry

In the present paper, a simultaneous pre-concentration procedure for the sequential determination of cadmium and lead in table salt samples using flame atomic absorption spectrometry is proposed. This method is based on the liquid-liquid extraction of cadmium(II) and lead(II) ions as dithizone complexes and direct aspiration of the organic phase for the spectrometer. The sequential determination of cadmium and lead is possible using a computer program. The optimization step was performed by a two-level fractional factorial design involving the variables: pH, dithizone mass, shaking time after addition of dithizone and shaking time after addition of solvent. In the studied levels these variables are not significant. The experimental conditions established propose a sample volume of 250 mL and the extraction process using 4.0 mL of methyl isobutyl ketone. This way, the procedure allows determination of cadmium and lead in table salt samples with a pre-concentration factor higher than 80, and detection limits of 0.3 ng g⁻¹ for cadmium and 4.2 ng g⁻¹ for lead. The precision expressed as relative standard deviation (n = 10) were 5.6 and 2.6% for cadmium concentration of 2 and 20 ng g⁻¹, respectively, and of 3.2 and 1.1% for lead concentration of 20 and 200 ng g⁻¹, respectively. Recoveries of cadmium and lead in several samples, measured by standard addition technique, proved also that this procedure is not affected by the matrix and can be applied satisfactorily for the determination of cadmium and lead in saline samples. The method was applied for the evaluation of the concentration of cadmium and lead in table salt samples consumed in Salvador City, Bahia, Brazil.     

Determination of zinc and copper in human hair by slurry sampling employing sequential multi-element flame atomic absorption spectrometry

The present work proposes a direct method based on slurry sampling for the determination of zinc and copper in human hair samples by multi-element sequential flame atomic absorption spectrometry. The slurries were prepared by cryogenic grinding and sonication of the samples. The optimization step was performed using univariate methodology and the factors studied were: nature and concentration of the acid solution, amount sample/slurry volume, sonication time, and particle size. The established experimental conditions are the use of a sample mass of 50 mg, 2 mol L^− 1 nitric acid solution, sonication time of 20 min and slurry volume of 10 mL. Adopting the optimized conditions, this method allows the determination of zinc and copper with detection limits of 88.3 and 53.3 ng g^− 1, respectively, and precision expressed as relative standard deviation (RSD) of 1.7% and 1.6% (both, n = 10) for contents of zinc and copper of 100.0 and 33.3 μg g^− 1, respectively. The accuracy was checked and confirmed by analysis of two certified reference materials of human hair. The procedure was applied for the determination of zinc and copper in two human hair samples. The zinc and copper contents varied from 100.0 to 175.6 and from 3.2 to 32.8 μg g^− 1, respectively. These samples were also analyzed after complete digestion in a closed system and determination by FAAS. The statistical comparison by t-test (95% confidence level) showed no significant difference between these results.     

Determination of major and trace elements in human scalp hair by pressurized-liquid extraction with acetic acid and inductively coupled plasma–optical-emission spectrometry

An analytical method has been developed for determination of major (Ca, K, Mg, and Na) and trace elements (As, Cd, Co, Li, Ni, and Sr) in human scalp hair. The proposed method includes a novel, simple, rapid, highly efficient, and automated metal-leaching procedure, by pressurized-liquid extraction (PLE), combined with a rapid simultaneous detection system—inductively coupled plasma–optical-emission spectrometry (ICP–OES). PLE is one of the most promising recently introduced sample-preparation techniques, with the advantages of reducing solvent consumption and enabling automated sample handling. The operating conditions for PLE, including concentration of the extraction solvent, extraction temperature, static time, number of extraction steps, pressure, mean particle size, diatomaceous earth (DE) mass/sample mass ratio, and flush volume were studied using an experimental design (Plackett–Burman design, PBD). The optimum conditions were use of 0.75 mol L⁻¹ acetic acid as extracting solution and powdered hair samples thoroughly mixed with DE, as a dispersing agent, at a DE mass/sample mass ratio of 4. Extraction was performed at room temperature and an extraction pressure of 140 atm for 5 min in one extraction step. The flush volume was fixed at 60%. The PLE-assisted multi-element leaching proposed is complete after 7 min (5 min static time plus 1 min purge time plus 1 min end relief time). Under the optimised conditions the figures of merit, for example limits of detection and quantification, repeatability of the over-all procedure, and accuracy, were evaluated. Analysis of GBW-07601 (human hair) certified reference material revealed accuracy was good for the target elements. The optimised method was finally applied to several human scalp-hair samples.     

Determination of lead and manganese in biological samples and sediment using slurry sampling and flame atomic absorption spectrometry

A procedure was developed for the determination of lead (Pb) and manganese (Mn) using slurry sampling. The two elements were detected using flame atomic absorption spectrometry with a slotted tube atom trap. Slurries were prepared by adding nitric acid solution (0.30%, w/v) to a powdered sample (0.10 g). After homogenization by ultrasonic bath for 15 min, the slurries were introduced directly into the detection equipment. Some conditions of the procedure were evaluated, such as acid concentration, presence of surfactants, and sonication time. Under optimized conditions, the LODs and LOQs achieved were 0.8 and 2.6 microg/g for Pb and 0.5 and 1.6 microg/g for Mn, respectively. The precision obtained varied between 3.1 and 5.8% (Mn), and 2.6 and 5.4% (Pb) for slurries of shrimp and sediment. The analytical curves were established using aqueous standards in nitric acid solutions. The accuracy of the method was assessed through the determination of Pb and Mn in the following certified reference materials: ERM-CE 278 (mussel tissue), CRM 397 (human hair), and SRM 1646a (estuarine sediment). The proposed procedure was successfully applied to the determination of Pb and Mn in six samples of shrimp powder, seasoning, and river sediment. The levels of Mn detected varied from 2.2 to 71.3 microg/g; Pb was detected in only one sediment sample (4.3 microg/g).     

Application of ultrasound-assisted acid leaching procedures for major and trace elements determination in edible seaweed by inductively coupled plasma-optical emission spectrometry

A new method using diluted reagents (nitric and hydrochloric acids and oxygen peroxide) and ultrasound energy to assist metals acid leaching with from edible seaweed was optimized. The method uses a first sonication at high temperature with hydrochloric acid as a previous stage to an ultrasound-assisted acid leaching with 7 ml of an acid solution containing nitric acid, hydrochloric acid and hydrogen peroxide at concentrations of 3.7, 3.0 and 3.0 M, respectively. Optimum conditions for the first sonication step were ultrasound energy at 17 kHz, sonication temperature at 65 °C, an acid volume of 2 ml, an hydrochloric acid concentration of 6.0 M and a sonication time of 10 min. It has been found that the first sonication stage at high temperature with hydrochloric acid is necessary to obtain quantitative recoveries for As, Ba, Fe and V. Otherwise quantitative recoveries were reached for the other elements investigated (Ca, K, Na, Mg, Cd, Cr, Cu, Mn, Ni, Pb and Zn). The repeatability of the ultrasound-assisted acid leaching method was around 10% for all elements. Adequate limit of detection and limit of quantification were reached by using inductively coupled plasma-optical emission spectrometry (ICP-OES) for measurements. The method resulted accurate after analysing several seaweed certified reference materials (IAEA-140/TM, NIES-03 and NIES-09). The method was finally applied to the multi-element determination in edible seaweed samples.     

Determination of zinc and copper in human hair by slurry sampling employing sequential multi-element flame atomic absorption spectrometry

The present work proposes a direct method based on slurry sampling for the determination of zinc and copper in human hair samples by multi-element sequential flame atomic absorption spectrometry. The slurries were prepared by cryogenic grinding and sonication of the samples. The optimization step was performed using univariate methodology and the factors studied were: nature and concentration of the acid solution, amount sample/slurry volume, sonication time, and particle size. The established experimental conditions are the use of a sample mass of 50 mg, 2 mol L^− 1 nitric acid solution, sonication time of 20 min and slurry volume of 10 mL. Adopting the optimized conditions, this method allows the determination of zinc and copper with detection limits of 88.3 and 53.3 ng g^− 1, respectively, and precision expressed as relative standard deviation (RSD) of 1.7% and 1.6% (both, n = 10) for contents of zinc and copper of 100.0 and 33.3 μg g^− 1, respectively. The accuracy was checked and confirmed by analysis of two certified reference materials of human hair. The procedure was applied for the determination of zinc and copper in two human hair samples. The zinc and copper contents varied from 100.0 to 175.6 and from 3.2 to 32.8 μg g^− 1, respectively. These samples were also analyzed after complete digestion in a closed system and determination by FAAS. The statistical comparison by t-test (95% confidence level) showed no significant difference between these results.     

On-line simultaneous pre-concentration procedure for the determination of cadmium and lead in drinking water employing sequential multi-element flame atomic absorption spectrometry

An on-line pre-concentration system for the sequential determination of cadmium and lead in drinking water by using fast sequential flame atomic absorption spectrometry (FS-FAAS) is proposed in this paper. Two minicolums of polyurethane foam loaded with 2-(6-methyl-2-benzothiazolylazo)-orcinol (Me-BTAO) were used as sorptive pre-concentration media for cadmium and lead. The analytical procedure involves the quantitative uptake of both analyte species by on-column chelation with Me-BTAO during sample loading followed by sequential elution of the analytes with 1.0?mol?L^?1 hydrochloric acid and determination by FS-FAAS. The optimisation of the entire analytical procedure was performed using a Box–Behnken multivariate design utilising the sampling flow rate, sample pH and buffer concentration as experimental variables.

The proposed flow-based method featured detection limits (3σ) of 0.08 and 0.51?µg?L^?1 for cadmium and lead, respectively, precision expressed as relative standard deviation (RSD) of 1.63% and 3.87% (n?=?7) for cadmium at the 2.0?µg?L^?1 and 10.0?µg?L^?1 levels, respectively, and RSD of 6.34% and 3.26% (n?=?7) for lead at the 5.0?µg?L^?1 and 30.0?µg?L^?1 levels, respectively. The enrichment factors achieved were 38.6 and 30.0 for cadmium and lead, respectively, using a sample volume of 10.0?mL. The sampling frequency was 45 samples per hour. The accuracy was confirmed by analysis of a certified reference material, namely, SRM 1643d (Trace elements in natural water). The optimised method was applied to the determination of cadmium and lead in drinking water samples collected in Santo Amaro da Purificação City, Bahia, Brazil.     

A pre-concentration procedure using coprecipitation for determination of lead and iron in several samples using flame atomic absorption spectrometry

The present paper proposes a pre-concentration procedure for determination of lead and iron in several samples by flame atomic absorption spectrometry. In it, lead(II) and iron(III) ions are coprecipitated using the violuric acid-copper(II) system as collector. Afterwards, the precipitate is dissolved with 1 M HNO₃ solution and the metal ions are determined. The optimization step was performed using factorial design involving the variables: pH, violuric acid mass (VA) and copper concentration (Cu).Using the optimized experimental conditions, the proposed procedure allows the determination these metals with detection limits of 0.18 μg L⁻¹ for iron and 0.16 μg L⁻¹ for lead. The effects of foreign ions on the pre-concentration procedure were also evaluated and the results demonstrated that this method could be applied for determination of iron and lead in several real samples. The proposed method was successfully applied to the analysis of seawater, urine, mineral water, soil and physiological solution samples. The concentrations of lead and iron achieved in these samples agree well with others data reported in the literature.     

Application of a dispersive micro‐solid‐phase extraction method for pre‐concentration and ultra‐trace determination of cadmium ions in water and biological samples

A method for the trace determination of cadmium ions in water, human urine and human blood serum samples using ultrasonic‐assisted dispersive micro‐solid‐phase extraction (UA‐D‐μSPE) was developed. Silica‐coated magnetic nanoparticles were coated with polythiophene, and the resulting sorbent was characterized using thermogravimetry, differential thermal analysis, scanning electron microscopy, Fourier transform infrared spectrometry and X‐ray diffraction. Following UA‐D‐μSPE, cadmium ions were quantified using graphite furnace atomic absorption spectrometry. A Box–Behnken design was used for optimization of important sorption and desorption parameters in UA‐D‐μSPE: in the sorption step, pH of solution, sorption amount and sonication time for sorption; in the desorption step, concentration of eluent, volume of eluent and sonication time. The optimum conditions for the method were: pH of solution, 7.5; sonication time for sorption, 3 min; sorption amount, 35 mg; type and concentration of eluent, HCl and 1.1 mol l^?1; volume of eluent, 360 μl; sonication time for desorption, 110 s. Under the optimized conditions the limit of detection and relative standard deviation for the detection of cadmium ions by UA‐D‐μSPE were found to be 0.8 ng l^?1 and <6%, respectively.     

A rapid and simple method for the determination of trace metals in hair samples by atomic absorption spectrometry

Acid digestion procedures are described for the dissolution of human head hair in routine determinations of cadmium, chromium, mercury, lead and zinc in the same sample solution by means of atomic absorption spectrometry. The techniques employed are atomization in a Massman graphite furnace or in an air—acetylene flame; the cold-vapor cell is used for mercury. The entire analytical procedure is tested with powdered homogenized head hair samples, previously analyzed by other analytical techniques. Comparison of the results demonstrates that the proposed technique is at least as precise and accurate as the other procedures used.     

Multivariate optimization of a microwave-assisted leaching procedure using dilute acid solutions,for FAAS determination of Cu,Fe, Mn,and Zn in multivitamin/multimineral supplements

This paper reports the development of a microwave-assisted procedure for leaching of copper, iron, manganese, and zinc from multivitamin/multimineral supplements by use of dilute acid before determination by flame atomic absorption spectrometry (FAAS). A Doehlert design was used to find optimum conditions for the procedure by use of response-surface methodology. Three variables (acid concentration in the leaching solution, irradiation time, and irradiation power) were used as factors in the optimization study for two acids, HCl and HNO₃. Final working conditions were established as a compromise between the optimum values for each analyte, taking into consideration the robustness of the procedure. The best leaching results were obtained with HNO₃ and the acid concentration, irradiation time, and irradiation power used were 0.70 mol L⁻¹, 15 min and 360 W, respectively. The accuracy of the optimized procedure was evaluated by comparison with a well-established closed-vessel microwave dissolution technique.     

Removal of exogenously bound elements from human hair by various washing procedures and determination by inductively coupled plasma mass spectrometry

A review of the literature shows that a variety of washing procedures to remove external contamination from hair have been proposed, but as yet no standardised procedures are available. In this study, methods for the pre-treatment and determination of antimony, arsenic, cadmium, chromium, lead, mercury and selenium in human hair by inductively coupled plasma mass spectrometry (ICP-MS) are developed.Investigations of various washing procedures to remove external contaminants show that in unexposed hair samples cadmium, lead and mercury are significantly removed from hair using a 0.1 M HCl wash, with 87, 73 and 5%, respectively being washed-off. The removal of antimony, arsenic and chromium from unexposed hair is, however, more efficient with 1% (v/v) sodium lauryl sulphate (SLS), with 43, 40 and 13% of each element, respectively being washed-off. Selenium is not removed from the hair by any of the washing methods studied. For the digestion of hair samples a digestion mixture of nitric acid and hydrogen peroxide is used.Experiments with simulated sweat spiked with each of these elements show that exogenously bound chromium, cadmium and lead are removed after washing with 0.1 M HCl. In contrast, antimony, arsenic, selenium and mercury irreversibly bind and, thus, are not removed with any of the washing solutions investigated. This work also compares hair levels of these elements in an unexposed and exposed group using the method developed.     

Determination of trace cadmium in waters by flame atomic absorption spectrophotometry after preconcentration with 1-nitroso-2-naphthol-3,6-disulfonic acid on Ambersorb 572

A procedure for the determination of trace amount of cadmium after adsorption of its 1-nitroso-2-naphthol-3,6-disulfonic acid chelate on Ambersorb 572 has been proposed. This chelate is adsorbed on the adsorbent in the pH range 3-8 from large volumes of aqueous solution of water samples with a preconcentration factor of 200. After being sorbed, cadmium was eluted by 5 mL of 2.0 mol L(-1) nitric acid solution and determined directly by flame atomic absorption spectrophotometery (FAAS). The detection limit (3sigma) of cadmium was 0.32 microg L(-1). The precision of the proposed procedure, calculated as the relative standard deviation of recovery in sample solution (100 mL) containing 5 microg of cadmium was satisfactory (1.9%). The adsorption of cadmium onto adsorbent can formally be described by a Langmuir equation with a maximum adsorption capacity of 19.6 mg g(-1) and a binding constant of 6.5 x 10(-3) L mg(-1). Various parameters, such as the effect of pH and the interference of a number of metal ions on the determination of cadmium, have been studied in detail to optimize the conditions for the preconcentration and determination of cadmium in water samples. This procedure was applied to the determination of cadmium in tap and river water samples.     

Coupling continuous ultrasound-assisted extraction, preconcentration and flame atomic absorption spectrometric detection for the determination of cadmium and lead in mussel samples

Continuous ultrasound-assisted extraction has been coupled with preconcentration and flame atomic absorption spectrometry for the determination of cadmium and lead in mussel samples. Experimental designs were used for the optimisation of the leaching and preconcentration steps. The use of diluted nitric acid as extractant in the continuous mode at a flow rate of 3.5 ml min⁻¹ and room temperature was sufficient for quantitative extraction of these trace metals. A minicolumn containing a chelating resin (Chelite P, with aminomethylphosphoric acid groups) was proved as an excellent material for the quantitative preconcentration of cadmium and lead prior to their flame atomic absorption detection. A flow injection manifold was used as interface for coupling the three analytical steps, which allowed the automation of the whole analytical process. A good precision of the whole procedure (2.0 and 2.3%), high enrichment factors (20.5 and 11.8) and a detection limit of 0.011 and 0.25 μg g⁻¹ for cadmium and lead, respectively, were obtained for 80 mg of sample. The sample throughputs were ca. 16 and 14 samples h⁻¹ for cadmium and lead, respectively. The accuracy of the analytical procedures was verified by using a standard reference material (BCR 278-R, mussel tissue) and the results were in good agreement with the certified values. The method was successfully applied to the determination of trace amounts of cadmium and lead in mussel samples from the coast of Galicia (NW, Spain).     

Fast ultrasound-assisted extraction of copper,iron, manganese and zinc from human hair samples prior to flow injection flame atomic absorption spectrometric detection

A dynamic ultrasound-assisted extraction procedure utilizing diluted nitric acid was developed for the determination of copper, iron, manganese and zinc in human hair taken from workers in permanent contact with a polluted environment. The extraction unit of the dynamic ultrasound-assisted extraction system contains a minicolumn into which a specified amount of hair (5–50 mg) is placed. Once inserted into the continuous manifold, trace metals were extracted at 3 mL min⁻¹ with 3 mol L⁻¹ nitric acid under the action of ultrasound for 2 min for zinc and 3 min for copper, iron and manganese determination, and using an ultrasonic water-bath temperature of 70 °C for zinc and 80 °C for copper, iron and manganese determination. The system permits the direct analysis of hair and yields concentrations with relative standard deviations of <3% (n = 11). The applicability of the procedure was verified by analysing human hair samples from workers exposed to welding fumes, and its accuracy was assessed through comparison with a conventional sample dissolution procedure and the use of a certified reference material (BCR 397, human hair).     

Determination of Cadmium and Lead in Human Teeth Samples Using Dispersive Liquid‐liquid Microextraction and Graphite Furnace Atomic Absorption Spectrometry

A new method for the determination of cadmium and lead in human teeth was developed based on dispersive liquid‐liquid microextraction preconcentration and graphite furnace atomic absorption spectrometry determination. In the proposed approach, O,O‐diethyldithiophosphate (DDTP) was used as a chelating agent, and carbon tetrachloride and methanol were selected as extraction and dispersive solvents. Some factors influencing the extraction efficiency of cadmium and lead and their subsequent determination, including extraction and dispersive solvent type and volume, pH of sample solution, concentration of the chelating agent and extraction time, were studied and optimized. Under the optimum conditions, the enrichment factor of 116 and 68 for cadmium and lead were achieved. The detection limit for cadmium and lead was 5.6 and 45 ng L^?1, and the relative standard deviation (R.S.D) was 4.5% and 3.8% (n = 7, c = 1.0 ng mL^?1), respectively. Verification of the accuracy of the method was carried out by analysis of a standard reference material (NIST 1486, bone meal). The method was successfully applied to the determination of trace amount of cadmium and lead in human teeth samples with satisfactory results.     

Application of multivariate optimization in the development of an ultrasound-assisted extraction procedure for multielemental determination in bean seeds samples using ICP OES

In this paper, multivariate optimization was applied for the development of an ultrasound-assisted multielemental extraction procedure for analysis of bean samples by inductively coupled plasma optical emission spectrometry. For this procedure, powdered samples were treated with an acid mixture and submitted to ultrasound energy for extracting the target elements (Ba, Ca, Cu, Fe, K, Mg, Mn, Sr and Zn). Centroid simplex mixture design was used for optimize the acid proportions (nitric, acetic and chloride acid) and Box Behnken design was applied for optimize the process variables (particle size, final concentration of extracting solution and sonication time) after mixture optimization. Iron had not presented quantitative extractions and it was excluded from final samples analysis. The developed method presents the follow limits of quantification in μg g^{− 1}: Ba (0.90); Ca (5.2); Cu (4.0); K (0.90); Mg (1.4); Mn (0.22); Sr (0.25) and Zn (4.0). Accuracy was accessed by comparison of determined concentration with the values obtained by the microwave digestion procedure. The proposed method was applied toward the determination of elemental composition in bean samples collected in the country zone from Jequié city located on the Bahia State, Brazil. The trace elements content ranged from 0.21 to 3.04, 3.84 to 10.8, 0.60 to 5.23, 31.0 to 46.5 and 10.8 to 19.6 μg g^{− 1} Ba, Cu, Sr, Zn, Mn, respectively. The major elements content ranged from 0.0418 to 0.0877, 0.109 to 0.153 and 1.30 to 1.56% (w/w) Ca, Mg and K, respectively.     

Rapid coprecipitation-separation and flame atomic absorption spectrometric determination of lead and cadmium in water with cobalt (II) and ammonium pyrrolidine dithiocarbamate

A coprecipitation technique which does not require complete collection of the precipitate was proposed for the determination of trace lead and cadmium in water with flame atomic absorption spectrometry (FAAS) after preconcentration of lead and cadmium by using cobalt (II) and ammonium pyrrolidine dithiocarbamate (Co-APDC) as coprecipitant and known amount of cobalt as an internal standard. Since lead, cadmium and cobalt were well distributed in the homogeneous precipitate, the concentration ratio of lead to cobalt, and cadmium to cobalt remained unchanged in any part of the precipitate. The amount of lead and cadmium in the original sample solution can be calculated respectively from the ratio of the absorbance values of lead and cadmium to cobalt in the final sample solution that is measured by FAAS and the known amount of the lead and cadmium in the standard series solutions. The optimum pH range for quantitative coprecipitation of lead and cadmium is from 3.0 to 4.5. The 16 diverse ions tested gave no significant interferences in the lead and cadmium determination. Under optimised conditions, lead ranging from 0 to 40?µg and cadmium ranging from 0 to 8?µg were quantitatively coprecipitated with Co-APDC from 100?mL sample solution (pH?～?3.5). This coprecipitation technique coupled with FAAS was applied to the determination of lead and cadmium in water samples with satisfactory results (recoveries in the range of 94.0–108%, relative standard deviations <6.0%).     

Factorial design in the optimization of preconcentration procedure for lead determination by FAAS

The present paper proposes a preconcentration procedure for lead determination using flame atomic absorption spectrometry (FAAS). It is based on lead(II) ions extraction as brilliant cresyl blue (BCB) complex and its sorption onto Diaion HP-2MG, a methacrylic ester copolymer. The optimization step was carried out using factorial design and the variables studied were pH, shaking time and reagent concentration. In the established experimental conditions, lead can be determinate with a limit of detection of 3.7 μg L⁻¹ lead (N = 20) and a relative standard deviation of 7% for a lead concentration of 100 μg L⁻¹. The accuracy was confirmed by analysis of a certified reference material, the stream sediment furnished by National Research Centre for Certified Reference Materials (NRCCRM), China (GBW 07310). Effect of other ions in the procedure proposed was also studied. The method was applied for lead determination in real samples of water, tea, soil and dust. Tests of addition/recovery in the experiments for lead determination in water samples revealed that the proposed procedure could be applied satisfactorily for analysis of these samples.