Surface chemistry of aerosolized silicon nanoparticles: evolution and desorption of hydrogen from 6-nm diameter particles

The surface chemistry of pristine, 6-nm silicon nanoparticles has been investigated. The particles were produced in an RF plasma and studied using a tandem differential mobility analysis apparatus, Fourier transform infrared spectroscopy (FTIR), time-of-flight secondary ion mass spectrometry (ToF-SIMS), and transmission electron microscopy. Particles were extracted from the plasma, which operates at approximately 20 Torr, into an atmospheric pressure aerosol flow tube, and then through a variable-temperature furnace that could be adjusted between room temperature and 1200 degrees C. DMA measurements show that freshly generated silicon particles shrink with heating, with particle diameters decreasing by approximately 0.25 nm between 350 and 400 degrees C. FTIR results indicate that freshly generated particles are primarily covered with SiH2 groups and smaller amounts of SiH and SiH3. Spectra recorded as a function of heating temperature indicate that the amount of surface hydrogen, as measured by the intensity of modes associated with SiH, SiH2, and SiH3, decreases with heating. ToF-SIMS measurements also suggest that hydrogen desorbs from the particles surfaces over the same temperature range that the particles shrink.     

Tunable photoluminescent and cathodoluminescent properties of ZnO and ZnO:Zn phosphors

ZnO and ZnO:Zn powder phosphors were prepared by the polyol-method followed by annealing in air and reducing gas, respectively. The samples were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), X-ray photoelectron spectra (XPS), electron paramagnetic resonance (EPR), and photoluminescence (PL) and cathodoluminescence (CL) spectra, respectively. The results indicate that all samples are in agreement with the hexagonal structure of the ZnO phase and the particle sizes are in the range of 1-2 microm. The PL and CL spectra of ZnO powders annealed at 950 degrees C in air consist of a weak ultraviolet emission band (approximately 390 nm) and a broad emission band centered at about 527 nm, exhibiting yellow emission color to the naked eyes. When the sample was reduced at the temperatures from 500 to 1050 degrees C, the yellow emission decreased gradually and disappeared completely at 800 degrees C, whereas the ultraviolet emission band became the strongest. Above this temperature, the green emission ( approximately 500 nm) appeared and increased with increasing of reducing temperatures. According to the EPR results and spectral analysis, the yellow and green emissions may arise from the transitions of photogenerated electron close to the conduction band to the deeply trapped hole in the single negatively charged interstitial oxygen ion (Oi(-)) and the single ionized oxygen vacancy (V.O) centers, respectively.     

Interaction of water with titania: implications for high-temperature gas sensing

High-temperature gas sensors based on semiconducting metal oxides show potential for optimization of combustion processes, resulting in efficient energy use and minimization of emissions. Such metal oxides can function as gas sensors because of the reaction of the sensing gas (e.g., CO) with ionosorbed oxygen species on the oxide surface with the resulting increase in conductivity. A limitation of metal oxide sensors is their difficulty of distinguishing between different gases. Designing selectivity into sensors necessitates a better understanding of the chemistry of gas-solid interactions at high temperatures. In this paper, we have used in situ infrared spectroscopy to monitor the dehydration of a hydrated anatase surface up to 600 degrees C and also to examine the hydration/dehydration of anatase held at 400 degrees C. When the O-H stretching region (3000-3800 cm(-1)) was primarily focused on, it was found that water loss from the titania surface proceeded at lower temperatures (<200 degrees C) through desorption, whereas at higher temperatures, water dissociation to terminal (approximately 3710 cm(-1)) and bridged (approximately 3660 cm(-1)) hydroxyl groups was noted. With a further increase in temperature to 600 degrees C, the bridged hydroxyl groups disappeared faster than the terminal ones. The electrical resistance of anatase at 600 degrees C was measured in the presence of moist gas streams and resulted in an increase in conductivity in the presence of water. In situ vibrational spectroscopy indicated a temporal correlation between the appearance of the bridging hydroxyl group and the change in electrical resistance. Several possible mechanisms are discussed. The chemical reaction of water with anatase at high temperatures necessitates that water be removed from the gas stream to avoid interference. A strategy involving the use of a hydrophobic microporous filter that can reject water and let gases such as CO pass unimpeded is examined. Successful use of such a concept has been demonstrated with a silicalite filter using moist CO gas streams.     

Restructuring and redispersion of silver on SiO2 under oxidizing/reducing atmospheres and its activity toward CO oxidation

The effects of oxygen-hydrogen pretreatments of nanosilver catalysts in cycle mode on the structure and particle size of silver particles, and subsequently the activity of the catalyst toward CO oxidation (or CO selective oxidation in the presence of H2), are reported in this paper. Ag/SiO2 catalyst with silver particle sizes of ca. 6 approximately 8 nm shows relatively high activity in the present reaction system. The adopting of a cycle of oxidation/reduction pretreatment has a marked influence on the activity of the catalyst. Oxygen pretreatment at 500 degrees C results in the formation of subsurface oxygen and activates the catalyst. As evidenced by in-situ XRD and TEM, the following H2 treatment at low temperatures (100 approximately 300 degrees C) causes surface faceting and redispersing of the silver particles without destroying the subsurface oxygen species. The subsequent in-situ FTIR and catalytic reaction results show that CO oxidation occurs at -75 degrees C and complete CO conversion can be obtained at 40 degrees C over such a nanosilver catalyst pretreated with oxygen at 500 degrees C followed by H2 at 100 degrees C. However, prolonged hydrogen treatment at high temperatures (>300 degrees C) after oxygen pretreatment at 500 degrees C induces the aggregation of silver particles and also depletes so much subsurface oxygen species that the pathway of CO oxidation by the subsurface oxygen species is inhibited. Meanwhile, the ability of the catalyst to adsorb reactants is greatly depressed, resulting in a 20 approximately 30% decrease in the activity toward CO oxidation. However, the activity of the catalyst pretreated with oxygen at 500 degrees C followed by hydrogen treatment at high temperatures (>300 degrees C) is still higher than that directly pretreated with H2. This kind of catalytic behavior of silver catalyst is associated with physical changes in the silver crystallites because of surface restructuring and crystallite redispersion during the course of oxygen-hydrogen pretreatment steps.     

Spectroscopic study on sorption of hydrogen sulfide by means of red soil

This paper reports the results of the characterization of red soils in relation to the sorption of H2S from coal gas at 500 degrees C by spectroscopic techniques in order to provide more information on red soils' structural change both before and after reaction. In addition, by-products analysis has also been studied using Fourier transform infrared (FTIR) spectroscopy. Before and after the experiments the red soils were characterized with X-ray powder diffraction (XRPD), energy dispersion spectrum (EDS), X-ray photoelectron spectroscopy (XPS) and FTIR spectroscopy. XRPD results indicate that iron oxide species disappear from the original to reacted red soil. EDS analysis shows that a significant amount of sulfur is present in the reacted red soil, which is in agreement with the results of the elemental analysis and the calculated value based on breakthrough curve. XPS regression fitting results further indicate that sulfur retention may be associated with the iron oxides. S 2p XPS fittings point out that the major sulfur species present in the reacted red soil are composed of S(-2), elemental sulfur, polysulfide, sulfite and sulfate. Additionally, the binding energy of iron shifts to a lower position for the reacted red soil, which indicates that iron oxides in the original red soil have been converted into iron sulfide. Appreciable amounts of the by-products CO2, SO2 and COS are detected by on-line FTIR spectroscopy during the initial and later stages of the sorption process. The formation of CO2 is related to the water-shift reaction, and SO2 is probably attributable to the reaction of organic matters and H2S. The concentration of COS is quantified by GC/FPD and found it to be about 350 ppm, which is close to the equilibrium concentration of the reaction of inlet CO and H2S at a temperature of 500 degrees C.     

Investigation of surface and thermogravimetric characteristics of carbon-coated iron nanopowder

Demand for high-density press and sinter components is increasing day by day. Of the different ways to improve the sinter density, the addition of nanopowder to the conventional micrometer-sized metal powder is an effective solution. The present investigation is aimed at studying the surface chemistry of iron nanopowder coated with graphitic carbon, which is intended to be mixed with the conventional iron powder. For this purpose, iron nanopowder in the size range of 30 nm to submicron (less than 1 micron) was investigated using thermogravimetry at different temperatures: 400°C, 600°C, 800°C, 1000°C, and 1350°C. The X-ray photoelectron spectroscopy (XPS), Auger electron spectroscopy (AES), and high-resolution scanning electron microscopy (HR-SEM) were used for characterizing the powder as well as samples sintered at different temperatures. The presence of iron, oxygen, carbon, chromium, and zinc were observed on the surface of the nanopowder. Iron was present in oxide state, although a small metallic iron peak at 707 eV was also observed in the XPS spectra obtained from the surface indicating the oxide scale to be maximum of about 5 nm in thickness. For the sample treated at 600°C, presence of manganese was observed on the surface. Thermogravimetry results showed a two-step mass loss with a total mass loss of 4 wt.% when heated to 1350°C where the first step corresponds to the surface oxide reduction.     

氧化石墨烯水热还原前后的发光光谱

分别采用改进Hummers方法和水热还原法制备了氧化石墨烯(GO)和还原氧化石墨烯(RGO)。 GO和RGO经透射电子显微镜(TEM)、紫外-可见吸收光谱(UV-Vis)、红外光谱(IR)、荧光发射和激发光谱(PL、PLE)等技术手段进行了表征。 荧光发射光谱显示,氧化石墨烯(GO)在可见光的激发下可以得到波长在600~800 nm范围内的宽谱近红外荧光。 通过比较氧化石墨烯水热还原前后的光谱变化,发现氧化石墨烯近红外荧光起源于氧化石墨烯的表面含氧基团,如C=O、COOH。 近红外荧光穿透性好、对生物组织损坏小,非常适合于生物成像,预示着氧化石墨烯在生物成像方面的应用潜力。     

Insights into the oxidation and decomposition of CO on Au/alpha-Fe2O3 and on alpha-Fe2O3 by coupled TG-FTIR

CO oxidation and decomposition behaviors over nanosized 3% Au/alpha-Fe2O3 catalyst and over the alpha-Fe2O3 support were studied in situ via thermogravimetry coupled to on-line FTIR spectroscopy (TG-FTIR), which was used to obtain temperature-programmed reduction (TPR) curves and evolved gas analysis. The catalyst was prepared by a sonication-assisted Au colloid based method and had a Au particle size in the range of 2-5 nm. Carburization studies of H 2-prereduced samples were also made in CO gas. According to gravimetry, for the 3% Au/alpha-Fe2O3 catalyst, there were three distinct stages of CO interaction with the Au catalyst but only two stages for the catalyst support. At low temperatures (相似文献   

Preparation of nanometer-sized In2O3 particles by a reverse microemulsion method

Nanometer-sized indium oxide (In(2)O(3)) particles have been prepared by chemical reaction of inorganic indium compounds and ammonia gas in a reverse microemulsion system consisting of water, Triton X-100 (surfactant), n-heptanol (co-surfactant), and n-octane (oil). Precursor hydroxides precipitated in the droplets of water-in-oil (W/O) microemulsion were calcined at different temperatures to form indium oxide powder. The factors affecting the particle size have been discussed; the calcination temperature is considered to be the important factor for controlling the size. In(2)O(3) calcined at 400 degrees C had a spherical form and a narrow size distribution. Calcination at 800 degrees C led to the formation of particles not only of irregular shape, but also of a wide size distribution. With the increase in calcination temperature from 400 to 800 degrees C, the average size of the particles grew from 7 to about 40 nm. The species of reactants used in the aqueous phase had a significant effect on the size of the particles. The average diameter of In(2)O(3) particles derived from reactant InCl(3) was 7 nm; that of particles derived from In(NO(3))(3) was 15 nm. The In(2)O(3) nanoparticles were characterized by transmission electron microscopy and X-ray diffraction. The phase behavior of the microemulsions is discussed.     

Structural and adsorption characteristics and catalytic activity of titania and titania-containing nanomaterials

Morphological, structural, adsorption, and catalytic properties of highly disperse titania prepared using sulfate and pyrogenic methods, and fumed titania-containing mixed oxides, were studied using XRD, TG/DTA, nitrogen adsorption, (1)H NMR, FTIR, microcalorimetry on immersion of oxides in water and decane, thermally stimulated depolarization current (TSDC) and catalytic photodecomposition of methylene blue (MB). Phase composition and aggregation characteristics of nanoparticles (pore size distribution) of sulfate and pyrogenically prepared titania are very different; temperature dependent structural properties are thus very different. Catalytic activity for the photodecomposition of MB is greatest (per gram of TiO(2) for the pure oxide materials) for non-treated ultrafine titania PC-500, which has the largest S(BET) value and smallest particle size of the materials studied. However, this activity calculated per m(2) is higher for PC-105, possessing a much smaller S(BET) value than PC-500. The activity per unit surface area of titania is greatest for the fumed silica-titania mixed oxide ST20. Calcination of PC-500 at 650 degrees C leads to enhancement of anatase content and catalytic activity, but heating at 800 and 900 degrees C lowers the anatase content (since rutile appears) and diminishes catalytic activity, as well as the specific surface area because of nanoparticle sintering.     

Characterisation of nanocrystalline magnesium oxide by X-ray absorption spectroscopy.

There are numerous methods of preparing nanocrystalline materials. Magnesium oxide is an ideal model system on which to probe the relation of the preparative route and the microstructure. Using X-ray absorption spectroscopy (XAS) we show that the sol-gel route can be used to prepare highly crystalline material provided there is careful control of the calcination conditions. In the present work this is achieved by calcining at high temperatures (at least 800 degrees C). However, this results in grain growth that can be prevented by the addition of a pinning agent, SiO(2), during the preparation of the sol. The pinned samples maintain a particle size of 11 nm even after calcining at 1000 degrees C. Ball-milling is a common method of preparing nanocrystalline oxides, however the present work shows that this produces a significant fraction of amorphous material, the fraction increasing with decreasing grain size (e.g. approximately 30 % for a grain size of 23 nm).     

Thin films of vanadium oxide grown on vanadium metal: oxidation conditions to produce V2O5 films for Li‐intercalation applications and characterisation by XPS,AFM, RBS/NRA

Thin films of vanadium oxide were grown on vanadium metal surfaces (i) in air at ambient conditions, (ii) in 5 mM H₂SO₄ (aq), pH 3, (iii) by thermal oxidation at low oxygen pressure (10^?5 mbar) at temperatures between 350 and 550 °C and (iv) at near‐atmospheric oxygen pressure (750 mbar) at 500 °C. The oxide films were investigated by atomic force microscopy (AFM), X‐ray photoelectron spectroscopy (XPS), X‐Ray diffraction (XRD) and Rutherford backscattering spectrometry (RBS) and nuclear reaction analysis (NRA). The lithium intercalation properties were studied by cyclic voltammetry (CV). The results show that the oxide films formed in air at room temperature (RT), in acidic aqueous solution, and at low oxygen pressure at elevated temperatures are composed of V₂O₃. In air and in aqueous solution at RT, the oxide films are ultra‐thin and hydroxylated. At 500 °C, nearly atmospheric oxygen pressure is required to form crystalline V₂O₅ films. The oxide films grown at pO₂ = 750 mbar for 5 min are about 260‐nm thick, and consist of a 115‐nm outer layer of crystalline V₂O₅. The inner oxide is mainly composed of VO₂. For all high temperature oxidations, the oxygen diffusion from the oxide film into the metal matrix was considerable. The oxygen saturation of the metal at 450 °C was found, by XPS, to be 27 at.% at the oxide/metal interface. The well‐crystallized V₂O₅ film, formed by oxidation for 5 min at 500 °C and 750 mbar O₂, was shown to have good lithium intercalation properties and is a promising candidate as electrode material in lithium batteries. Copyright © 2005 John Wiley & Sons, Ltd.     

Preparation of mesoporous carbon from commercial activated carbon with steam activation in the presence of cerium oxide

Mesoporous carbon was prepared from the commercial activated carbon by steam activation with cerium oxide as catalyst. Steam activation with a catalyst loading of 0.5-2.0 wt% at 680-870 degrees C was examined. The surface area and pore size were evaluated by nitrogen adsorption at 77 K, and the structure of cerium oxide was characterized by XRD, XPS, and TEM. The results showed that the catalyst promoted the development of a mesopore at lower temperature (680-740 degrees C), and the mesopore was concentrated around 4-10 nm. The noncatalytic activation was advantageous in mesopore development and the catalyst would restrict the formation of mesopores at high temperature (800-870 degrees C). Higher loading of cerium oxide and higher activation temperature caused the aggregation of cerium oxide and then resulted in scattered pore size distribution.     

Adlayers of dimannoside thiols on gold: surface chemical analysis

Carbohydrate films on gold based on dimannoside thiols (DMT) were prepared, and a complementary surface chemical analysis was performed in detail by X-ray photoelectron spectroscopy (XPS), time-of-flight secondary ion mass spectrometry (ToF-SIMS), near-edge X-ray absorption fine structure (NEXAFS), FT-IR, and contact angle measurements in order to verify formation of ω-carbohydrate-functionalized alkylthiol films. XPS (C 1s, O 1s, and S 2p) reveals information on carbohydrate specific alkoxy (C-O) and acetal moieties (O-C-O) as well as thiolate species attached to gold. Angle-resolved synchrotron XPS was used for chemical speciation at ultimate surface sensitivity. Angle-resolved XPS analysis suggests the presence of an excess top layer composed of unbound sulfur components combined with alkyl moieties. Further support for DMT attachment on Au is given by ToF-SIMS and FT-IR analysis. Carbon and oxygen K-edge NEXAFS spectra were interpreted by applying the building block model supported by comparison to data of 1-undecanethiol, poly(vinyl alcohol), and polyoxymethylene. No linear dichroism effect was observed in the angle-resolved C K-edge NEXAFS.     

The behavior of hydroxyl units of synthetic goethite and its dehydroxylated product hematite.

The behavior of the hydroxyl units of synthetic goethite and its dehydroxylated product hematite was characterized using a combination of Fourier transform infrared (FTIR) spectroscopy and X-ray diffraction (XRD) during the thermal transformation over a temperature range of 180-270 degrees C. Hematite was detected at temperatures above 200 degrees C by XRD while goethite was not observed above 230 degrees C. Five intense OH vibrations at 3212-3194, 1687-1674, 1643-1640, 888-884 and 800-798 cm(-1), and a H2O vibration at 3450-3445 cm(-1) were observed for goethite. The intensity of hydroxyl stretching and bending vibrations decreased with the extent of dehydroxylation of goethite. Infrared absorption bands clearly show the phase transformation between goethite and hematite: in particular. the migration of excess hydroxyl units from goethite to hematite. Two bands at 536-533 and 454-452 cm(-1) are the low wavenumber vibrations of Fe-O in the hematite structure. Band component analysis data of FTIR spectra support the fact that the hydroxyl units mainly affect the a plane in goethite and the equivalent c plane in hematite.     

Monitoring Silica Supported Molybdenum Oxide Catalysts at Work: A Raman Spectroscopic Study

The structure of silica SBA‐15‐supported molybdenum oxide catalysts is investigated during selective oxidation of propylene at 500 °C using operando Raman spectroscopy. The active catalysts contain mixtures of dispersed molybdenum oxide species exhibiting monooxo and dioxo structure. An increase in molybdenum oxide loading results in a decrease of the ratio of dioxo and monooxo species from 3.8 to 1.9, as determined by quantitative analysis of Raman spectra. Additional in situ Raman studies at 500 °C reveal that the dioxo/monooxo ratio increases in the presence of steam at higher molybdenum oxide loadings. The observed structural changes are assigned to shifts in the equilibrium between dioxo and monooxo species resulting from hydration/dehydration of the catalyst. This study demonstrates that the detailed structure of nanostructured molybdenum oxide catalysts depends on temperature, gas‐phase composition, and molybdenum oxide loading.     

Gold cluster formation on a fullerene surface

The growth of Au clusters on a fullerene thin film was investigated by in situ photoelectron spectroscopy in the ultraviolet (UPS) and x-ray (XPS) regime. Due to its highly corrugated surface fullerene films provide a wide range of bonding sites which could be exploited as molecular templates and serve to create a cluster superstructure. To gain insight into the fullerene-Au interaction two types of experiments were performed: (i) the deposition of Au on a fullerene surface, and (ii) the deposition of fullerenes on a Au surface. In both experiments an island growth mode is observed. The deposition of submonolayer amounts of C60 onto a gold film showed that the main interaction of the two species is due to chemisorption of the first C60 monolayer. In addition a constant band bending in the fullerene film is detected, but the UPS valence-band spectra show that there is no charge transfer from the Au to the C60 lowest unoccupied molecular orbital. In the reverse experiment, the cluster growth of Au on the corrugated C60 surface, the analysis of the Au core level does not reveal a specific bonding or nucleation site for Au atoms and clusters. This is in contrast to observations with Si clusters, which prefer to reside in the troughs between the fullerene molecules. The Au clusters grow continually from a size of about 55 atoms for the early stages of growth up to 150 atoms for the deposition of a nominal coverage of 1.5 nm. These data are derived from an analysis of the d-band splitting and the Au 4f core-level shift due to delayed photohole relaxation. The thermal stability of the Au-clusters-covered fullerene film was investigated by annealing in situ up to temperatures of 650 degrees C. For temperatures up to 450 degrees C a continuous growth of the clusters is detected, which is accompanied by a slight drop in Au concentration in the range of XPS for annealing temperatures higher than 350 degrees C. This may be due to a ripening of the clusters. The presence of Au apparently delays fullerene sublimation. The film shows a very good thermal stability and even after annealing at 650 degrees C there is still a fullerene film detectable in the photoelectron spectroscopy spectra.     

Surfactant mediated synthesis of spherical binary oxides photocatalytic with enhanced activity in visible light

Spherical silica and zirconia mixed titania and pure titania samples were prepared in presence of cetyltrimethylammonium bromide (CTAB) through controlled hydrolysis of corresponding metal alcoxides. Effect of surfactant amount and calcinations temperature on morphology, surface area and photocatalytic activity is studied using PXRD, SEM, FTIR, Solid state UV-vis spectroscopy and BET surface area. It is well observed that in presence of 2 mol% CTAB, uniform sized spherical oxide particles can be synthesized. However, increasing or decreasing the surfactant amount does not favor the spherical particle formation. Material synthesis in presence of CTAB not only helps in the spherical particle formation but also increases the surface area and visible light absorption. Studies on photocatalytic lead removal with respect to calcination temperature indicate that the calcination at 500 degrees C is most suitable for the best photocatalytic activity. Mixing of zirconia and silica helps in anatase phase stabilization even at 900 degrees C calcination. Accordingly low decrease in surface area even at 900 degrees C calcination is observed. Due to the phase stabilization and higher surface area binary oxide materials showed comparatively better photocatalytic activity even after calcination at 900 degrees C. So it can be concluded that present synthesis approach can produce uniform sized spherical binary oxide materials with better photocatalytic activity in visible light.     

Microstructural and surface characterization of solid state sensor based on LaFeO3-sigma oxide for detection of NO2

NO2 adsorption on non-stoichiometric perovskite-type LaFeO3-sigma thick films increases the density of charge carriers (holes), thus facilitating the detection of NO2 by conduction measurements. In this work, the microstructures and induced defects that control the sensing behaviour of LaFeO3-sigma were investigated in depth. LaFeO3-sigma powders were prepared both by thermal decomposition of a La[Fe(CN)6].nH2O complex at 700 degrees C and by using a sol-gel method at 500 degrees C. Scanning electron microscopy (SEM) revealed crystallites varying in size from 100 to 300 nm depending on the decomposition temperature. Surface analysis by X-ray photoelectron spectroscopy (XPS) confirmed that sintering in nitrogen is much more effective for reducing the amount of surface oxygen than is sintering in air. At low operating temperature, there is a drift of the output response associated with the ongoing process of bulk equilibration, but it is much less at 350 degrees C. It is obvious that a variation of [Oad]/[Olattice] with sintering conditions represents the relative gas adsorption capability.     

Tuning the Structure of Platinum Particles on Ceria In Situ for Enhancing the Catalytic Performance of Exhaust Gas Catalysts

A dynamic structural behavior of Pt nanoparticles on the ceria surface under reducing/oxidizing conditions was found at moderate temperatures (<500 °C) and exploited to enhance the catalytic activity of Pt/CeO₂‐based exhaust gas catalysts. Redispersion of platinum in an oxidizing atmosphere already occurred at 400 °C. A protocol with reducing pulses at 250–400 °C was applied in a subsequent step for controlled Pt‐particle formation. Operando X‐ray absorption spectroscopy unraveled the different extent of reduction and sintering of Pt particles: The choice of the reductant allowed the tuning of the reduction degree/particle size and thus the catalytic activity (CO>H₂>C₃H₆). This dynamic nature of Pt on ceria at such low temperatures (250–500 °C) was additionally confirmed by in situ environmental transmission electron microscopy. A general concept is proposed to adjust the noble metal dispersion (size, structure), for example, during operation of an exhaust gas catalyst.