Enhanced stereocomplex formation of poly(L-lactic acid) and poly(D-lactic acid) in the presence of stereoblock poly(lactic acid)

Stereoblock poly(lactic acid) (sb-PLA) is incorporated into a 1:1 polymer blend system of poly(L-lactic acid) (PLLA) and poly(D-lactic acid) (PDLA) that has a high molecular weight to study its addition effect on the stereocomplex (sc) formation of PLLA and PDLA. The ternary polymer blend films are first prepared by casting polymer solutions of sb-PLA, PLLA, and PDLA with different compositions. Upon increasing the content of sb-PLA in the blend films the sc crystallization is driven to a higher degree, while the formation of homo-chiral (hc) crystals is decreased. Lowering the molecular weight of the incorporated sb-PLA effectively increases the sc formation. Consequently, it is revealed that sb-PLA can work as a compatibilizer to improve the poor sc formation in the polymer blend of PLLA and PDLA.     

Thermal analysis of the double-melting behavior of poly(L-lactic acid)

The melting and crystallization behavior of poly(L -lactic acid) (PLLA; weight-average molecular weight = 3 × 10⁵) was studied with differential scanning calorimetry (DSC). DSC curves for PLLA samples were obtained at various cooling rates (CRs) from the melt (210 °C). The peak crystallization temperature and the exothermic heat of crystallization determined from the DSC curve decreased almost linearly with increasing log(CR). DSC melting curves for the melt-crystallized samples were obtained at various heating rates (HRs). The double-melting behavior was confirmed by the double endothermic peaks, a high-temperature peak (H) and a low-temperature peak (L), that appeared in the DSC curves at slow HRs for the samples prepared with a slow CR. Peak L increased with increasing HR, whereas peak H decreased. The peak melting temperatures of L and H [T_m(L) and T_m(H)] decreased linearly with log(HR). The appearance region of the double-melting peaks (L and H) was illustrated in a CR–HR map. Peak L decreased with increasing CR, whereas peak H increased. T_m(L) and T_m(H) decreased almost linearly with log(CR). The characteristics of the crystallization and double-melting behavior were explained by the slow rates of crystallization and recrystallization, respectively. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 25–32, 2004     

Superiority of poly(L-lactic acid) microspheres as dermal fillers

The demand for injectable dermal filler has unde rgone significant growth with the rapid development of the beauty industry.Poly(lactic acid)(PLA) as a benefit of excellent biocompatibility and long-term promotion of collagen regeneration has been favored as a commonly used filler.However,the effects of chirality and particle size of PLA on the efficacy of dermal filler have not been studied.In this study,we prepared three kinds of microspheres(MSs) consisting of poly(D-lactic acid)(PDLA MS),poly(L-lactic acid)(PLLA MS),or meso-PLA(PDLLA MS)at 5,10 and 20 μmto reveal the different biological functions as dermal filler.Following intradermal injection into guinea pig,it was found that PLLA MS induced the slightest inflammation,and the level of pro-inflammatory cytokine IL-1β induced by PLLA MS is only 0.3 or 0.7-fold of that induced by PDLA or PDLLA MS,respectively.More importantly,PLLA MS significantly stimulated the regeneration of collagen,which was 1.4 or 1.1 times higher than those stimulated by PDLA MS or PDLLA MS,respectively.The size of PLA MSs did not affect the levels of inflammation and collagen regeneration.The results confirmed the superiority of PLLA as a dermal filler.     

Micro construction of poly(epsilon-caprolactone)/poly(L-lactic acid) blend film by solution casting under microwave irradiation

The micro construction of poly(epsilon-caprolactone) (PCL) and poly(L-lactic acid) (PLLA) blend films fabricated by solution casting under microwave irradiation was investigated by selective enzymatic degradation and scanning electron microscopy (SEM). The results were totally different from the blends obtained by conventional methods. The blend was more homogeneous and the PCL continuous phase more compact as no spherulites and tiny zone separation were observed from the film surface and no PCL network was observed inside the film, and the degradation of a PCL plank by Pseudomonas lipase was significantly retarded. The distributed PLLA micro spheres were enlarged and amorphous. The thermal behavior of the blend by microwave heating revealed that PCL and PLLA underwent a melting process, which induced the variations of the PCL phase and PLLA spheres. The weight loss caused by degradation of the PCL/PLLA blend obtained by conventional methods (B50c) is greater than that of the blend obtained by microwave methods (B50m), which reflects the change in morphology from a loose PCL network (B50c) to a dense PCL plank (B50m).     

制备聚(L-乳酸-co-乙醇酸）/聚D-乳酸共混物立构复合物的新方法

首次以高分子量的聚(L-乳酸-co-乙醇酸）(PLLGA）和D-聚乳酸（PDLA)［m(PLLGA) : m(PDLA)=3:1, c 50 mL·g^-1］为原料,氯仿为溶剂,等体积的甲醇为沉淀剂,于50 ℃蒸发4 h形成了PLLGA和PDLA的立构复合物（sc-PLA）,其结构和性能经XRD, DSC和TGA表征。结果表明：sc-PLA的结晶度达96.2%,热失重5%温度为342 ℃（PLLGA为304 ℃）。     

Preparation and characterization of electrospun fibers based on poly(L-lactic acid)/cellulose acetate

PLLA/CA mixtures of different compositions were successfully electrospun to obtain composite nanofibrous membranes.The microstructures of the membrances changed from homogeneous to heterogeneous with the addition of CA, which was observed by FE-ESEM.The PLLA/CA fabric membranes were characterized by mechanical testing,DSC and contact angle measurements.The tensile stress of the composite fibrous membranes increased obviously with the increase of CA content.DSC results indicated that the CA component was the main factor for the changes of enthalpies in the composite fibers.Contact angle measurements showed the hydrophilicity of the electrospun nanofiber membranes was improved with the addition of CA.     

光学纯度对聚左旋乳酸结晶与熔融行为的影响

通过示差扫描量热仪(DSC)和广角X射线衍射仪(WAXD)研究了聚左旋乳酸(PLLA)的光学纯度(91.6%、93.3%、94.0%、97.0%、98.4%)对聚乳酸结晶和熔融行为的影响。 在非等温结晶过程中,随着光学纯度的提高,聚乳酸的结晶峰值温度、熔点、熔融焓均提高。 在等温结晶过程中,PLLA的半结晶时间(t_1/2)随着光学纯度的增加而减少,在结晶温度100~110 ℃区间内半结晶时间均达到最小值;含有不同光学纯度PLLA的Avrami指数n≈3,表明光学纯度的变化不能改变聚乳酸以三维球晶生长的异相成核机理。 随着光学纯度的增加,聚乳酸δ-晶型转变为α-晶型的临界温度升高。 聚乳酸的结晶和熔融行为对光学纯度具有依赖性。     

静电纺丝法制备胆固醇-g-聚乳酸液晶/ 聚乳酸复合纳米纤维膜

以辛酸亚锡为催化剂, 胆固醇(CHOL)为共引发剂引发D,L-丙交酯开环聚合, 制备了胆固醇-g-聚(D,L-乳酸)(CHOL-g-PDLLA)低聚物, 采用偏光显微镜(POM)和差示扫描量热(DSC)方法考察了其液晶特性. 通过静电纺丝技术制备了CHOL/PDLLA和CHOL-g-PDLLA /PDLLA复合纳米纤维膜, 对其形貌、界面相容性、孔隙率、拉伸性能和细胞相容性进行了研究. 结果表明, CHOL-g-PDLLA为一种热致胆甾型液晶, 液晶温度区间为21.8~74.5 ℃; CHOL-g-PDLLA/PDLLA复合纳米纤维膜的纤维形态良好, 表面均匀光滑, 孔隙率在70%~75%之间, 且其界面相容性优于相应的CHOL/PDLLA. 随着CHOL和CHOL-g-PDLLA含量的增加, 复合纳米纤维膜的拉伸强度逐渐下降, 但CHOL-g-PDLLA/PDLLA复合纳米纤维膜的拉伸强度显著大于CHOL/PDLLA. 体外骨髓间充质干细胞培养结果显示, CHOL-g-PDLLA/PDLLA复合纳米纤维膜具有良好的细胞相容性, 且优于相应的PDLLA和CHOL/PDLLA纳米纤维膜.     

Structure and compatibility of poly(vinyl alcohol)-silk fibroin (PVA/SA) blend films

The structure and compatibility of poly(vinyl alcohol)-silk fibroin (PVA/SF) blend films were analyzed by differential scanning calorimetry (DSC), thermomechanical (TMA) and thermogravimetric (TGA) analysis, x-ray diffractometry, and scanning (SEM) and transmission (TEM) electron microscopy. DSC curves of PVA/SF blend films showed a major endothermic peak at 220°C, along with a peak at 280°C. These endotherms were assigned to the thermal decomposition of the ordered PVA elements and to the thermal degradation of silk fibroin, respectively. The PVA/SF blends behaved in a manner intermediate to the pure components, as suggested by both contraction expansion and sample weight retention properties recorded by TMA and TGA measurements. The IR absorption spectra of the blends were identified as purely a composite of the absorption bands characteristic of both PVA and SF pure polymers. The X-ray diffraction patterns of PVA/SF blends showed overlapping spacing due to PVA and SF. A dispersed phase formed by spherical particles of 3–7 μm diameter was observed by SEM and TEM. All these findings suggest that PVA and SF are incompatible. © 1994 John Wiley & Sons, Inc.     

Effects of MA-g-PP and lignocellulosic filler addition on several properties of poly(L-lactic acid)/polypropylene composites

The aim of this study was to investigate the effects of maleic anhydride-graft-polypropylene (MA-g-PP) as a compatibilizer and wood fiber as a lignocellulosic filler on technical properties of poly(l-lactic acid) (PLLA)/polypropylene composites. The obtained composites were characterized through mechanical tests, thermogravimetric analysis, differential scanning analyzer, and chemical analysis via Fourier transform infrared spectroscopy (FTIR), and scanning electron microscope (SEM). The obtained results showed that the mechanical properties of the composites containing MA-g-PP were higher than those of the composites without MA-g-PP. SEM images revealed that the morphological properties of the composites including PP and PLLA were improved. The chemical interactions between PP and PLLA were demonstrated through FTIR results of composites with MA-g-PP.     

聚乙二醇甲醚-聚(D,L-乳酸)嵌段共聚物纳米胶束的制备

聚乙二醇甲醚-聚(D;L-乳酸)嵌段共聚物纳米胶束的制备;聚乙二醇单甲醚;两亲性二嵌段共聚物;纳米沉淀技术     

热致相分离制备聚乳酸纳米纤维支架

本研究以二氧六环/叔丁醇为溶剂体系,采用热致相分离方法制备出具有多级孔径的三维连通的聚乳酸纳米纤维支架. 探讨了陈化、陈化温度、聚合物浓度、二氧六环/叔丁醇 (溶剂/非溶剂)比例对纳米纤维支架的结构和纤维直径大小的影响. 结果表明,陈化对较低聚合物浓度下(≤7%)纳米纤维结构的形成影响明显,而在较高聚合物浓度时(＞10%),只要控制在一定温度下相分离即可形成纳米纤维结构的支架;较低的陈化温度(≤5℃)有利于纳米纤维状网络结构(直径约20-300nm)的形成,且随着陈化温度的下降,纤维网络结构分布更加均匀;聚乳酸浓度增加, 纤维细化,网络结构分布更均匀,所形成的孔结构也更致密;叔丁醇含量≤12%时,纤维直径变化不大;当叔丁醇含量＞12%时,纤维直径明显增加(约500 nm).     

Real-time enzymatic degradation study of poly[(R)-3-hydroxybutyric acid] copolymer thin film by atomic force microscopy in buffer solution

In situ observation of lamellar crystals during the enzymatic degradation by poly(hydroxybutyrate) (PHB) depolymerase is carried out on the thin films of poly[((R)-3-hydroxybutyric acid)-co-(16 mol-%-(R)-3-hydroxypentanoic acid)] using atomic force microscopy in buffer solution. Erosion of lamellar crystals and formation of splintered morphology along the crystal growth direction are directly observed during the course of the enzymatic degradation process. The changes in lamellar morphologies caused by enzymatic degradation are discussed in terms of lamellar crystal growth process.

AFM images of a P[(R)-3HB-co-(R)-3HV] thin film before and during enzymatic degradation.     

Thermal degradation of poly(ethyl methacrylate) and its copolymer with poly(ethyl acrylate)

The thermal degradation behaviour of poly(ethyl methacrylate) homopolymers and poly(ethyl methacrylate) and poly(ethyl acrylate) copolymers synthesized by using the benzoyl peroxide-di-methyl aniline redox pair at different temperatures (18–35C) was investigated. Contrary to some reports in the literature, the thermal degradation of PEMA was observed to take place in multi steps. These are assigned to be loss of labile end groups, side chain scission, anhydride formation and main chain degradation steps. Dominating chemical formations at the end of these steps were characterized by FTIR spectroscopy.The homopolymer samples synthesized at 18C showed a greater thermal stability against degradation. Copolymerization with small amounts of ethyl acrylate was observed to impart thermal stability to PEMA by stabilizing mainly the end groups against degradations.     

Water absorption and enzymatic degradation of poly(lactic acid)/rice starch composites

Poly(lactic acid) (PLA) composites consisting of PLA, rice starch (RS) (0–50 wt%) and epoxidised natural rubber (ENR50) were compounded by a twin-screw extruder and compression moulded into dumbbell specimens. Tensile tests were performed to characterize the mechanical properties of the PLA/RS composites. Morphological studies were done on the tensile fractured surface of the specimens by using scanning electron microscopy (SEM). Twenty weight percent of RS achieved a good balance of strength and stiffness. Beyond 20 wt% loading of RS, the tensile strength and elongation at break of PLA decreased drastically. This may be attributed to the agglomeration of RS, which could then act as stress concentrator. The incorporation of ENR50 increased the tensile strength and elongation at break of the PLA/RS composites remarkably, owing to the elastomeric behaviour and compatibilisation effects of ENR50. Interestingly, the morphology of PLA/RS composites transformed to a more ductile one with the addition of ENR. The kinetics of water absorption of the PLA/RS composites conforms to Fick's law. The M_m and D values are dependent on the RS and ENR concentrations. The tensile properties of the PLA/RS composites deteriorated after water absorption. The retention-ability and recoverability of the PLA/RS composites are relatively low, attributed to the hydrolysis of PLA, degradation of the PLA–RS interface and leaching of the RS particles. In addition, the tensile properties of PLA/RS composites decreased drastically upon exposure to enzymatic degradation. Extensive pinhole and surface erosion on the PLA/RS composites indicate high degree of hydrolysis. Whilst the addition of ENR leads to some improvements in tensile properties, nevertheless, it enhanced the biodegradability of the PLA/RS composites when exposed to water and -amylase enzymatic treatments.     

聚乳酸/纳米SiO_2复合材料的熔融和冷结晶行为

采用熔融共混法制备了聚乳酸(PLLA)/纳米SiO2复合材料;利用透射电镜观察了复合材料的微观形貌;利用差示扫描量热仪测定了该复合材料的熔融行为和非等温冷结晶行为;利用Jeziorny法和Mo法研究了PLLA及其复合材料的非等温冷结晶动力学.结果表明,纳米SiO2在PLLA基体中具有良好的分散性和异相成核作用,使得PLLA基体的结晶峰向低温方向移动;复合体系的熔融温度和熔融焓的变化与SiO2的加入量密切相关.采用Jeziorny法和Mo法均可以很好地处理复合材料的非等温冷结晶过程.     

Poly(methyl methacrylate)-induced Microstructure and Hydrolysis Behavior Changes of Poly(L-lactic acid)/Carbon Nanotubes Composites

Poly(L-lactic acid)(PLLA)-based composites exhibit wide applications in many fields.However,most of hydrophilic fillers usually accelerate the hydrolytic degradation of PLLA,which is unfavorable for the prolonging of the service life of the articles.In this work,a small quantity of poly(methyl methacrylate)(PMMA)(2 wt%-10 wt%)was incorporated into the PLLA/carbon nanotubes(CNTs)composites.The effects of PMMA content on the dispersion of CNTs as well as the microstructure and hydrolytic degradation behaviors of the composites were systematically investigated.The results showed that PMMA promoted the dispersion of CNTs in the composites.Amorphous PLLA was obtained in all the composites.Largely enhanced hydrolytic degradation resistance was achieved by incorporating PMMA,especially at relatively high PMMA content.Incorporating 10 wt%PMMA led to a dramatic decrease in the hydrolytic degradation rate from 0.19%/h of the PLLA/CNT composite sample to 0.059%/h of the PLLA/PMMA-10/CNT composite sample.The microstructure evolution of the composites was also detected,and the results showed that no crystallization occurred in the PLLA matrix.Further results based on the interfacial tension calculation showed that the enhanced hydrolytic degradation resistance of the PLLA matrix was mainly attributed to the relatively strong interfacial affinity between PMMA and CNTs,which prevented the occurrence of hydrolytic degradation at the interface between PLLA and CNTs.This work provides an alternative method for tailoring the hydrolytic degradation ability of the PLLA-based composites.     

Pervaporation of alcohol-toluene mixtures through polymer blend membranes of poly(acrylic acid) and poly(vinyl alcohol)

Homogeneous membranes were prepared by blending poly(acrylic acid) with poly(vinyl alcohol). These blend membranes were evaluated for the selective separation of alcohols from toluene by pervaporation. The flux and selectivity of the membranes were determined both as a function of the blend composition and of the feed mixture composition. The results showed that a polymer blending method could be very useful to develop new membranes with improved permselectivity. The pervaporation properties could be optimized by adjusting the blend composition. All the blend membranes tested showed a decrease in flux with increasing poly(vinyl alcohol) content for both methanol—toluene and ethanol—toluene liquid mixtures. The alcohols permeated preferentially through all tested blend membranes, and the selectivity values increased with increasing poly(vinyl alcohol) content. The pervaporation characteristics of the blend membranes were also strongly influenced by the feed mixture composition. The fluxes increased exponentially with increasing alcohol concentration in the feed mixtures, whereas the selectivities decreased for both liquid mixtures.     

Stereoblock poly(lactic acid): synthesis via solid-state polycondensation of a stereocomplexed mixture of poly(L-lactic acid) and poly(D-lactic acid)

Stereoblock poly(lactic acid) consisting of D- and L-lactate stereosequences can be successfully synthesized by solid-state polycondensation of a 1:1 mixture of poly(L-lactic acid) and poly(D-lactic acid). In the first step, melt-polycondensation of L- and D-lactic acids is conducted to synthesize poly(L-lactic acid) and poly(D-lactic acid) with a medium-molecular-weight, respectively. In the next step, these poly(L-lactic acid) and poly(D-lactic acid) are melt-blended in 1:1 ratio to allow formation of their stereocomplex. In the last step, this melt-blend is subjected to solid-state polycondensation at temperature where the dehydrative condensation is allowed to promote chain extension in the amorphous phase with the stereocomplex crystals preserved. Finally, stereoblock poly(lactic acid) having high-molecular-weight is obtained. The stereoblock poly(lactic acid) synthesized by this way shows a higher melting temperature in consequence of the controlled block lengths and the resulting higher-molecular-weight. The product characterization as well as the optimization of the polymerization conditions is described. Changes in M(w) of stereoblock poly(lactic acid) (sb-PLA) as a function of the reaction time.