Synthesis and properties of aromatic polyamides based on 4,4′-(2,7-naphthalenedioxy)dibenzoic acid

4,4′-(2,7-Naphthalenedioxy)dibenzoic acid, a new aromatic dicarboxylic acid monomer, was prepared starting from 2,7-dihydroxynaphthalene and p-fluorobenzonitrile in three steps. Using triphenyl phosphite (TPP) and pyridine as condensing agents, a series of novel aromatic polyamides were synthesized by the direct polycondensation of the diacid monomer and aromatic diamines in N-methyl-2-pyrrolidone (NMP) solution containing dissolved calcium chloride. The resulting polyamides had inherent viscosities ranging from 0.48 to 0.67 dL/g. Most of these polyamides were readily soluble in polar solvents, such as NMP and N,N-dimethylacetamide (DMAc). Transparent, flexible, and tough films were cast from their DMAc solutions. They had tensile strengths of 65–70 MPa, elongations to break of 5–7%, and initial moduli of 1.4–1.6 GPa. Most of these polymers proved to be amorphous, with glass transition temperatures in the range between 143–227°C. Thermogravimetric analysis (TG) showed that all the polyamides were stable up to 450°C in both air and nitrogen atmospheres. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1469–1478, 1997     

Synthesis and properties of Ortho-linked aromatic polyamides based on 4,4′-(2,3-naphthalenedioxy) dibenzoic acid

A novel aromatic dicarboxylic acid monomer, 4,4′-(2,3-naphthalenedioxy)-dibenzoic acid ( 3 ), was prepared by the fluorodisplacement reaction of p-fluorobenzonitrile with 2,3-dihydroxynaphthalene in N,N-dimethylformamide (DMF) in the presence of potassium carbonate followed by alkaline hydrolysis of the intermediate dinitrile. A series of novel aromatic polyamides containing ortho-linked aromatic units in the main chain were synthesized by the direct polycondensation of diacid 3 and a variety of aromatic diamines using triphenyl phosphite and pyridine as condensing agents in the N-methyl-2-pyrrolidone (NMP) solution containing dissolved calcium chloride. The resulting polyamides had inherent viscosities higher than 0.74 and up to 2.10 dL/g. All of these polyamides were soluble in polar solvents, such as NMP, DMF, N,N-dimethylacetamide (DMAc), and dimethyl sulfoxide. Transparent, flexible, and tough films could be cast from their DMAc or NMP solutions. The solvent-cast films had high tensile strengths and moduli. Extensions to break were relatively low, except for the polymers derived from 2,2-bis[4-(4-aminophenoxy)phenyl]hexafluoropropane and 3,4′-oxydianiline, which had elongations of 82 and 62%, respectively. Except for the polyamide based on p-phenylenediamine, all the other polyamides were amorphous in nature. All the polymers are thermally stable to temperatures in excess of 450°C in either air or nitrogen atmosphere. The polymers exhibited glass transition temperatures ranging from 183 to 260°C and decomposition temperatures (10% weight loss) ranging from 462–523°C in air and 468–530°C in nitrogen. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 3385–3391, 1997     

Preparation and properties of aromatic polyamides from 2,2′-bis(p-carboxyphenoxy) biphenyl or 2,2′-bis(p-carboxyphenoxy)-1,1′-binaphthyl and aromatic diamines

New aromatic dicarboxylic acids having kink and crank structures, 2,2′-bis(p-carboxyphenoxy) biphenyl and 2,2′-bis(p-carboxyphenoxy)-1,1′-binaphthyl, were synthesized by the reaction of p-fluorobenzonitrile with biphenyl-2,2′-diol and 2,2′-dihydroxy-1,1′-binaphthyl, respectively, followed by hydrolysis. Biphenyl-2,2′-diyl-and 1,1′-binaphthyl-2,2′-diyl-containing aromatic polyamides having inherent viscosities of 0.58–1.46 dL/g and 0.63–1.30 dL/g, respectively, were obtained by the low-temperature solution polycondensation of the corresponding diacid chlorides with aromatic diamines. These polymers were readily soluble in a variety of organic solvents including N,N-dimethylacetamide (DMAc), N-methyl-2-pyrrolidone (NMP), dimethyl sulfoxide, m-cresol, and pyridine. Transparent, pale yellow, and flexible films of these polymers could be cast from the DMAc or NMP solutions. These aromatic polyamides containing biphenyl and binaphthyl units had glass transition temperatures in the range of 210–272 and 260–315°C, respectively. They began to lose weight around 380°C, with 10% weight loss being recorded at about 450°C in air. © 1993 John Wiley & Sons, Inc.     

Preparation and properties of aromatic polyamides from 2,2′-bis(p-aminophenoxy) biphenyl or 2,2′-bis(p-aminophenoxy)-1,1′-binaphthyl and aromatic dicarboxylic acids

New aromatic diamines having kink and crank structures, 2,2′-bis(p-aminophenoxy)biphenyl and 2,2′-bis(p-aminophenoxy)-1,1′-binaphthyl, were synthesized by the reaction of p-fluoronitrobenzene with biphenyl-2,2′-diol and 2,2′-dihydroxy-1,1′-binaphthyl, respectively, followed by catalytic reduction. Biphenyl-2,2′-diyl- and 1,1′-binaphthyl-2,2′-diyl-containing aromatic polyamides having inherent viscosities of 0.44–1.18 and 0.26–0.88 dL/g, respectively, were obtained either by the direct polycondensation or low-temperature solution polycondensation of the diamines with aromatic dicarboxylic acids (or diacid chlorides). These polymers were readily soluble in a variety of organic solvents including N,N-dimethylacetamide (DMAc), N-methyl-2-pyrrolidone (NMP), dimethyl sulfoxide, m-cresol, and pyridine. Transparent, pale yellow, and flexible films of these polymers could be cast from the DMAc or NMP solutions. These aromatic polyamides containing biphenyl and binaphthyl units had glass transition temperatures in the range of 215–255 and 266–303°C, respectively. They began to lose weight at ca. 380°C, with 10% weight loss being recorded at about 470°C in air. © 1993 John Wiley & Sons, Inc.     

Synthesis and properties of soluble aromatic polyamides derived from 2,2′‐bis(4‐carboxyphenoxy)‐9,9′‐spirobifluorene

The synthesis of a new bis(ether carboxylic acid), 2,2′‐bis(4‐carboxyphenoxy)‐9,9′‐spirobifluorene, in which two orthogonally arranged carboxyphenoxyfluorene entities are connected through an sp³ carbon atom (the spiro center), is reported. The direct phosphorylation polycondensation of this diacid monomer with various aromatic diamines yields aromatic polyamides containing 9,9′‐spirobifluorene moieties in the main chain. The presence of the spiro segment restricts the close packing of the polymer chains and decreases interchain interactions, resulting in amorphous polyamides with enhanced solubility, and high glass‐transition temperatures and good thermal stability are maintained through controlled segmental mobility. The glass‐transition temperatures of these polyamides are in the range of 234–306 °C, with 10% weight losses occurring at temperatures above 530 °C. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1160–1166, 2003     

Synthesis and properties of soluble aromatic polyimides from 2,2′-bis(3,4-dicarboxyphenoxy)-1,1′-binaphthyl dianhydride and aromatic diamines

Aromatic tetracarboxylic dianhydride having crank and twisted noncoplanar structure, 2,2′-bis(3,4-dicarboxyphenoxy)-1,1′-binaphthyl dianhydride, was synthesized by the reaction of 4-nitrophthalonitrile with 2,2′-dihydroxy-1,1′-binaphthyl, followed by alkaline hydrolysis of the intermediate bis(ether dinitrile) and subsequent dehydration of the resulting bis(ether diacid). Binaphthyl-2,2′-diyl–containing novel aromatic polyimides having inherent viscosities up to 0.67 dL/g were obtained by the one-step polymerization process starting from the bis(ether anhydride) and various aromatic diamines. All the polyimides showed typical amorphous diffraction patterns. Most of the polyimides were readily soluble in common organic solvents such as N,N-dimethylacetamide (DMAc), N-methyl-2-pyrrolidone (NMP), and pyridine. These aromatic polyimides had glass transition temperatures in the range of 280–350°C, depending on the nature of the diamine moiety. All polymers were stable up to 400°C, with 10% weight loss being recorded above 485°C in air. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1937–1943, 1998     

Synthesis and properties of new soluble aromatic polybenzoxazoles from 4,4′-diamino-3,3′-dihydroxytriphenylamines and aromatic dicarboxylic acids

Two new triphenylamine-based bis (o-aminophenol) monomers, 4,4′-diamino-3,3′-dihydroxytriphenylamines, were successfully synthesized by the cesium fluoride-mediated condensation of 2-(benzyloxy)-4-fluoronitrobenzene with aniline derivatives, followed by simultaneous deprotection and reduction. Aromatic polybenzoxazoles having inherent viscosities of 0.58–1.05 dL/g were obtained by the low-temperature solution polycondensation of the bis(aminophenol)s with various aromatic dicarboxylic acid chlorides and the subsequent thermal cyclodehydration of the resultant poly(hydroxyamide)s. All the polybenzoxazoles were amorphous, and most of them were soluble in organic solvents such as m-cresol and o-chlorophenol. Flexible and tough films of polybenzoxazoles could be cast from the DMAc solutions of some aromatic poly(hydroxyamide)s, followed by thermal cyclodehydration. The glass transition temperatures and 10% weight loss temperatures of the polybenzoxazoles under nitrogen were in the range of 262–327 and 610–640°C, respectively. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1987–1994, 1998     

Synthesis and characterization of novel polyaryloxydiphenylsilane derived from 2,2′- dimethyl-biphenyl-4,4′-diol

A novel polyaryloxydiphenylsilane was synthesized successfully by solution polycondensation of 2,2′-dimethyl-biphenyl-4,4′-diol with diphenyldichlorosilane and the catalyst triethylamine in toluene at 80 °C. Polymers with a relatively high inherent viscosity and yield were obtained when the reactions were carried out in aromatic and lipophilic solvents. The novel polyaryloxydiphenylsilane was soluble in chlorinated aliphatic hydrocarbons such as methylene chloride and chloroform as well as in polar solvents such as dimethyl sulfoxide, N,N-dimethylformamide, and N,N-dimethylacetamide and also in some common organic solvents such as benzene and toluene. However, it was insoluble in both aliphatic hydrocarbons as well as in alcoholic solvents. The polyaryloxydiphenylsilane began losing weight around 400 °C under a nitrogen atmosphere, and the 10% weight-loss temperature was 473 °C. The glass-transition temperature of the polyaryloxydiphenylsilane was 102 °C. The glass transition could be lowered by the copolymerization technique with 2,2-bis(4-hydroxy-3,5-dimethylphenyl)propane as an aromatic diol comonomer. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 4591–4595, 1999     

Synthesis and characterization of polyarylates derived from 4,4′-dihydroxy-meta-terphenyl and aromatic diacid chlorides

Polyarylates derived from 4,4″-dihydroxy-meta-terphenyl (DHmTP) were prepared by the phase-transfer catalyzed, two-phase polycondensation with aromatic diacid chlorides. The resulting polymers were crystalline, solvent resistant, and produced brittle films. Copolymers with bisphenol-A were also synthesized using isophthaloyl diacid chloride. At low to moderate levels of DHmTP in the copolymers (25–75%), the materials had high glass transition temperatures (186–201°C), good solvent resistance, and gave tough, clear films. Terpolymers of DHmTP and BPA with 50:50 isophthaloyl and terphthaloyl diacid chloride were prepared with not much improvement over Ardel D-100®. All the DHmTP-polyarylates had good thermal stability (5% weight loss in air > 415–460°C) and had a high % char (20–48%). © 1994 John Wiley & Sons, Inc.     

Preparation and properties of new soluble aromatic polyimides from 2,2′-bis(3,4-dicarboxyphenoxy)biphenyl dianhydride and aromatic diamines

A new aromatic tetracarboxylic dianhydride having a crank and twisted noncoplannar structure, 2,2′-bis(3,4-dicarboxyphenoxy)biphenyl dianhydride, was synthesized by the reaction of 4-nitrophthalonitrile with biphenyl-2,2′-diol, followed by hydrolysis and cyclodehydration. The biphenyl-2,2′-diyl-containing aromatic polyimides having inherent viscosities up to 0.66 dL/g were obtained by the conventional two-step procedure starting from the dianhydride monomer and various aromatic diamines. Most of the polyimides were readily soluble in amide-type solvents such as N,N-dimethylacetamide and N-methyl-2-pyrrolidone. The aromatic polyimides had glass transition temperatures in the range of 205–242°C, and began to lose weight around 415°C, with 10% weight loss being recorded at about 500°C in air. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A Polym. Chem. 36: 2021–2027, 1998     

Synthesis and characterization of new soluble aromatic polyamides from diaminotetraphenylimidazolin-2-one and various aromatic dicarboxylic acid chlorides

Novel aromatic polyamides, having inherent viscosities of 0.76-2.31 dL/g, were synthesized by the low temperature solution polycondensation of a new highly phenylated diamine monomer having an imidazolinone group, 1,3-bis(4-aminophenyl)-4,5-diphenylimidazoline-2-one (TPIDA), with various aromatic diacid chlorides. All the polymers were amorphous, and most of the polyamides were readily soluble in organic solvents such as N-methyl–2-pyrrolidone, N,N-dimethylacetamide (DMAc), and m-cresol. Flexible and tough films could be prepared from the DMAc solutions of these soluble aromatic polyamides. The glass transition temperatures and 10% weight loss temperatures under nitrogen of the polyamides were in the range of 275–315°C and 430–505°C, respectively. © 1995 John Wiley & Sons, Inc.     

Synthesis and characterization of new soluble polyamides derived from 3,3′,5,5′-tetramethyl-2,2-bis[4-(4-carboxyphenoxy)phenyl]propane

A series of new soluble polyamides having isopropylidene and methyl-substituted arylene ether moieties in the polymer chain were prepared by the direct polycondensation of 3,3′,5,5′-tetramethyl-2,2-bis[4-(4-carboxyphenoxy)phenyl]propane and various diamines in N-methyl-2-pyrrolidinone (NMP) containing CaCl₂ using triphenyl phosphite and pyridine as condensing agents. Polymers were produced with moderate to high inherent viscosities of 0.85–1.47 dL g⁻¹ while the weight-average molecular weight and number-average molecular weight were in the range of 86,700–259,000 and 43,300–119,000, respectively. All the polymers were readily dissolved in polar aprotic solvents such as NMP, N,N-dimethylacetamide, and N,N-dimethylformamide, as well as less polar solvents such as m-cresol and pyridine, and even soluble in tetrahydrofuran. These polymers were solution-cast into transparent, flexible and tough films. All of the polymers were amorphous and the polyamide films had a tensile strength range of 82–122 MPa, an elongation at break range of 6–18%, and a tensile modulus range of 2.0–2.8 GPa. These polyamides had glass transition temperatures between 233–260°C and 10% weight loss temperatures in the range of 450–489 and 459–493°C in nitrogen and air atmosphere, respectively. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1997–2003, 1999     

Preparation and properties of aromatic polyimides from 2,2′-bis(p-aminophenoxy)biphenyl or 2,2′-bis)p-aminophenoxy)-1,1′-binaphthyl and aromatic tetracarboxylic dianhydrides

New aromatic polyimides containing a biphenyl-2,2′-diyl or 1,1′-binaphthyl-2,2′-diyl unit were prepared by a conventional two-step method starting from 2,2′-bis(p-aminophenoxy) biphenyl or 2,2′-bis(p-aminophenoxy)-1,1′-binaphthyl and aromatic tetracarboxylic dianhydrides. The polyimides having inherent viscosities of 0.69–0.99 and 0.51–0.59 dL/g, respectively, were obtained. Some of these polymers were readily soluble in a variety of organic solvents including N,N-dimethylacetamide (DMAc), N-methyl-2-pyrrolidone (NMP), dimethyl sulfoxide, and pyridine. Transparent, flexible, and pale yellow to brown films of these polymers could be cast from the DMAc or NMP polyamic acid solutions. These aromatic polyimides containing biphenyl and binaphthyl units had glass transition temperatures in the range of 200–235 and 286–358°C, respectively. They began to lose weight around 380°C, with 10% weight loss being recorded at about 470°C in air. © 1993 John Wiley & Sons, Inc.     

Synthesis and properties of 4,4′-biphenyldicarboxylic acid and 2,6-naphthalenedicarboxylic acid

This article describes the synthesis and the properties of polyesters and copolyesters prepared from ethylene glycol, terephthalic acid, 4,4′ biphenyldicarboxylic acid (BDA), and 2,6-naphthlenedicarboxylic acid (NDA). The effect of incorporating varying levels of BDA and NDA on polyethylene terephthalate (PET) is described. Depending on the concentration, incorporation of BDA into PET leads to an improvement in glass transition temperature (T_g), strength, modulus, and barrier properties. Copolymers of PET containing up to about 50% BDA derived units are clear and have T_g's ranging from 85 to 105°C, making them suitable for applications where a high T_g along with clarity is important. Copolymers with higher BDA concentration are highly crystalline, with high rates of crystallization from the melt. Copolymerization of NDA with oligoethyleneterephthalate leads to copolymers that are generally amorphous. Crystallinity can be developed in copolymers with low concentration of NDA by thermal annealing. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3139–3146, 1999     

A zinc(II) metal–organic framework with a novel topology formed from 4,4′,4′′‐nitrilotribenzoate and 4,4′‐bipyridine ligands

A metal–organic framework with a novel topology, poly[sesqui(μ₂‐4,4′‐bipyridine)bis(dimethylformamide)bis(μ₄‐4,4′,4′′‐nitrilotribenzoato)trizinc(II)], [Zn₃(C₂₁H₁₂NO₆)₂(C₁₀H₈N₂)_1.5(C₃H₇NO)₂]_n, was obtained by the solvothermal method using 4,4′,4′′‐nitrilotribenzoic acid and 4,4′‐bipyridine (bipy). The structure, determined by single‐crystal X‐ray diffraction analysis, possesses three kinds of crystallographically independent Zn^II cations, as well as binuclear Zn₂(COO)₄(bipy)₂ paddle‐wheel clusters, and can be reduced to a novel topology of a (3,3,6)‐connected 3‐nodal net, with the Schläfli symbol {5.6²}₄{5².6}₄{5⁸.8⁷} according to the topological analysis.     

Synthesis and characterization of soluble aromatic polyurea-amides from new N,N′--dimethyl-N,N′-bis(aminophenyl)ureas and aromatic dicarboxylic acid chlorides

Aromatic polyurea-amides having inherent viscosities of 0.36–0.67 dL/g were synthesized by the low temperature solution polycondensation of new N,N′-dimethyl-N,N′-bis(aminophenyl)ureas with various aromatic dicarboxylic acid chlorides. All the polymers were amorphous, and most of them were soluble in a variety of organic solvents such as N-methyl-2-pyrrolidone, N,N-dimethylacetamide (DMAc), m-cresol, and pyridine. Some of the polymers could be cast from the DMAc solutions into transparent and flexible films having good tensile properties. The glass transition temperatures of the polyurea-amides obtained from the bis(4-aminophenyl)-substituted ureas were 244–272°C. The temperatures of 10% weight loss under nitrogen of the polymers were in the range of 430 and 480°C. © 1995 John Wiley & Sons, Inc.     

Synthesis and characterization of sulfone-containing polyesters derived from 4,4′-dicarboxydiphenyl sulfone by direct polycondensation

Several sulfone-containing polyesters having inherent viscosities 0.43-0.19 dL g^?1 were prepared by direct polycondensation of 4,4′-dicarboxydiphenyl sulfone (DCDPS) with various aromatic and aliphatic diols, by p-toluenesulfonyl chloride and N,N′-dimethylformamide in pyridine solution. The polyesters were examined by elementary analysis, IR spectra, inherent viscosity, x-ray diffraction, solubility, DSC, and TGA. The diffraction diagram showed that all polyesters were crystalline except that obtained from bisphenol-A. All polymers were soluble in sulfonic acid (18M), phenol and p-chlorophenol, but not in acetone and toluene. These polymers obtained from aromatic bisphenols lost no mass below 325°C, but 10% loss of mass was recorded above 396°C in nitrogen. DCDPS copolymerized with isophthalic acid (IPA) and bisphenol-A had inherent viscosity up to 0.49 dL g^?1, with relatively narrow distribution of molar mass . © 1995 John Wiley & Sons, Inc.     

Fully aromatic liquid crystalline homopolyesters and copolyesters of 1,1′-binaphthyl-4,4′-diol

A series of fully aromatic, thermotropic polyesters based on 1,1′-binaphthyl-4,4′-diol, BND, was prepared by the melt polycondensation method and characterized for their thermotropic behavior by a variety of experimental techniques. The homopolymer of BND with terephthalic acid formed a nematic melt at 353°C. In contrast, the polyester from BND and 2,6-naphthalenedicarboxylic acid had a melting transition, T_m, above 400°C, so it was not possible with the equipment available to determine whether it formed a nematic melt. All of the copolymers of BND formed nematic melts at much lower T_m values than those of its respective homopolymers, as expected, because of the copolymerization effect of the added monomer. Moreover, all of the copolymers had higher glass transition temperatures, T_g, than those of other liquid crystalline polyesters and higher thermal stabilities. © 1994 John Wiley & Sons, Inc.