Synthesis,structure, and properties of hybrid organic–inorganic composites based on polysiloxanes. II. Comparisons between poly(methylphenylsiloxane) and poly(dimethylsiloxane), and between titania and silica

The work reported in the preceding article in this series is extended by consideration of polysiloxane–ceramic composites based on atactic poly(methylphenylsiloxane) (PMPS) elastomers instead of poly(dimethylsiloxane). The former is noncrystallizable because of its stereochemically irregular structure, while the latter is crystallizable. In addition, some composites were prepared by the in situ precipitation of titania instead of silica. The resulting materials were characterized using differential scanning calorimetry, equilibrium stress–strain measurements in elongation, small-angle neutron scattering, and transmission electron microscopy. The moduli of the PMPS elastomers were found to increase significantly with increase in amount of either type of filler, with reinforcing upturns at high elongation in the case of the silica. Because the PMPS elastomers were amorphous, it is obvious that strain-induced crystallization is not required for these upturns in modulus. Titania did not give as good reinforcement as did silica, at least in the case of PMPS. Differences in interactions between the polymer and the two fillers are obviously important in this regard, but differences in particle morphology probably also contribute. Specifically, the titania “particles” were significantly larger than the silica particles when observed in TEM, and appeared to be much more porous. The actual domain size as measured by scattering, however, was only approximately 5% larger. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1191–1200, 1998     

Polypropylene/layered double hydroxide nanocomposites: Synergistic effect of designed filler modification and compatibilizing agent on the morphology,thermal, and mechanical properties

This work addresses the optimization of the morphology, thermal, and mechanical properties of polypropylene/layered double hydroxide (LDH) nanocomposites. For this, the nanofillers were modified by a calcination rehydration process using two surfactants, sodium dodecylsulfate (SDS) and sodium dodecylbenzenesulfonate, respectively. The nanofillers were characterized at each step of the modification process by thermal gravimetry, X‐ray diffraction, and Infra red spectroscopy. Furthermore, the impact of anionic modifiers on the filler surface energy and on the interactions toward water was analyzed. Polypropylene (PP)/LDH nanocomposites were then prepared by a melt intercalation process and a high molar mass maleic anhydride functionalized polypropylene (PPgMA) was introduced as a compatibilizer. The dispersion of LDH in the PP matrix was characterized and the thermal and mechanical properties of the corresponding nanocomposites were determined and discussed as a function of the filler modification, of the nanocomposite morphology, and of the filler/matrix interfacial properties. The nanocomposites prepared from SDS modified LDH and PPgMA exhibited superior properties thanks to an optimized filler dispersion state and improved interfacial interactions. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 782–794     

Tuning the mechanical properties in model nanocomposites: Influence of the polymer‐filler interfacial interactions

This article presents a study of the polymer‐filler interfacial effects on filler dispersion and mechanical reinforcement in Polystyrene (PS)/silica nanocomposites by direct comparison of two model systems: ungrafted and PS‐grafted silica dispersed in PS matrix. The structure of nanoparticles has been investigated by combining small angle neutron scattering measurements and transmission electronic microscopic images. The mechanical properties were studied over a wide range of deformation by plate–plate rheology and uni‐axial stretching. At low silica volume fraction, the particles arrange, for both systems, in small finite size nonconnected aggregates and the materials exhibit a solid‐like behavior independent of the local polymer‐fillers interactions suggesting that reinforcement is dominated by additional long range effects. At high silica volume fraction, a continuous connected network is created leading to a fast increase of reinforcement whose amplitude is then directly dependent on the strength of the local particle–particle interactions and lower with grafting likely due to deformation of grafted polymer. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

New hydrocarbon side chain liquid crystalline polysiloxane polymers: Synthesis,characterization, and thermotropic behavior

A series of new and high-purity hydrocarbon liquid crystal monomers were synthesized through the acylation reaction, deoxygenation reaction, and Grignard reaction. ¹H-NMR spectra and elemental analyses were used to examine their purity. The liquid crystalline polysiloxane polymers were obtained by grafting the monomers onto poly(methylhydrosiloxane). The thermal transition temperature, mesomorphic properties, and mesophase textures of the monomers and the polymers were determined by differential scanning calorimetry (dsc), polarized optical microscopy, and X-ray diffraction analysis. Moreover, we observed the even–odd effect of the smectic/isotropic transition temperature with the length variation of the substituents. In this study, we found by X-ray diffraction that the liquid crystalline polysiloxane polymers undergo a transition from smectic B to smectic E mesophase. However, dsc has difficulty detecting the phase transition process. By considering the spin–lattice relaxation time (T₁), we can systematically explain the relation between the flexibility of the substituent with the smectic/isotropic transition temperature. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 2849–2863, 1998     

Synthesis and molecular structure analysis of nano‐sized methacryl‐grafted polysiloxane resin for fabrication of nano hybrid materials

The molecular structures of methacryl‐grafted polysiloxane resins from 3‐(trimethoxysilyl)propyl methacrylate (MPTS) and diphenylsilanediol (DPSD) were determined by theoretical computation and experimental measurement. The molecular structures obtained from theoretical computation coincided well with those from experimental measurement, and we found that the structural changes in the resins could be controlled by precursor compositions. While molecular weights and polysiloxane chain lengths of the resins increase with DPSD contents, their molecular sizes do not vary significantly. In the present study, molecular sizes and shapes of the resins with various compositions are hypothesized theoretically and proven experimentally. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 827–836, 2005     

Polylactide compositions. II. Correlation between morphology and main properties of PLA/calcium sulfate composites

Starting from calcium sulfate (gypsum) as fermentation by‐product of lactic acid production process, high performance composites have been produced by melt‐blending polylactide (PLA, L/D isomer ratio of 96:4) and β‐anhydrite II (AII) filler, that is, calcium sulfate hemihydrate previously dehydrated at 500 °C. Characterized by attractive mechanical and thermal properties due to good filler dispersion throughout the polyester matrix, these composites are interesting for potential use as biodegradable rigid packaging. Physical characterization of selected composites filled with 20 and 40 wt % AII has been performed and compared to processed unfilled PLA with similar amorphous structure. State of dispersion of the filler particles and interphase characteristic features have been investigated using light microscopy (LM) and scanning electron microscopy (SEM). Addition of AII did not decrease PLA thermal stability as revealed by thermogravimetry analyses (TGA) and allowed reaching a slight increase of PLA crystallizability during melt crystallization and upon heating from the glassy, amorphous state (DSC). It was found by thermomechanical measurements (DMTA) that the AII filler increased pronouncedly storage modulus (E′) of the composites in comparison with PLA in a broad temperature range. The X‐ray investigations showed stable/unchanged crystallographic structure of AII during processing with molten PLA and in the composite system. The notable thermal and mechanical properties of PLA–AII composites are accounted for by the good filler dispersion throughout the polyester matrix confirmed by morphological studies, system stability, and favorable interactions between components. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2770–2780, 2007     

Model filled rubber. II. Particle composition dependence of suspension rheology

Monodisperse size colloidal particles varying in chemical composition were synthesized by emulsifier‐free emulsion polymerization. Using a stress‐controlled rheometer, the rheological behavior of colloidal suspensions in a low molecular weight liquid polysulfide was investigated. All suspensions exhibited shear thinning behavior. The shear viscosity, dynamic moduli, and yield stress increased as interactions between particles and matrix increased. The rheological properties associated with network buildup in the suspensions were sensitively monitored by a kinetic recovery experiment. We propose that interfacial interactions by polar and hydrogen bonding between particles and matrix strongly promote affinity of matrix polymer to the filler particles, resulting in adsorption or entanglement of polymer chains on the filler surface. A network structure was formed consisting of particles with an immobilized polymer layer on the particle surface with each particle floc acting as a temporary physical crosslinking site. As the interfacial interaction increases, the adsorbed layer thickness on the filler particles, hence, the effective particle volume fraction, increases. As a result, the rheological properties were enhanced in the order PS < PMMA < PSVP. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 815–824, 1999     

Light scattering and transmission studies of nanofiller particulate size,matrix cavitation,and high strain interfacial dewetting behavior in silica‐elastomer composites

The effect of silica nanofiller surface chemistry on compounded particle size and high strain particle dewetting in a semitransparent nanosilica‐filled elastomer composite was determined using backscattered visible light and transmitted light, respectively. The integrated intensities of backscattered light from the samples were collected at various visible wavelengths for thin‐film composites using ultraviolet–visible spectrometer with an integrating sphere. The data revealed strong Rayleigh‐type scattering from compounded filler particles. Size information was extracted and found to broadly correlate with scanning electron microscopy image analysis of fracture surface. Incorporation of a siloxane surface treatment chemical during compounding resulted in a reduced average filler particle size in the cured composite. On extension of the samples, an optical transition was observed only in the filled composites. At high strains, the semi transparent samples displayed an abrupt drop in transparency becoming opaque. This was quantified using a simple light transmission‐sample extension technique. Strain‐induced crystallization was discounted as the cause for the transition by X‐ray diffraction analysis. The onset yield stress for the optical transition was found to be filler surface‐chemistry‐dependent with the siloxane‐treated filler exhibiting a greatly increased onset stress value. These observations were discussed and rationalized in terms of filler particle–matrix dewetting and cavitation at high strains. Matrix–filler dewetting was distinguished from matrix cavitation by comparison with Beer–Lambert behavior derived from unstrained samples. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011.     

Preparation and properties of nanocomposites based on acrylonitrile–butadiene rubber,styrene–butadiene rubber,and polybutadiene rubber

Nanocomposites were prepared with different grades of nitrile rubber with acrylonitrile contents of 19, 34, and 50%, with styrene–butadiene rubber (23% styrene content), and with polybutadiene rubber with Na‐montmorillonite clay. The clay was modified with stearyl amine and was characterized by X‐ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, and transmission electron microscopy (TEM). The XRD studies showed an increase in the gallery gap upon the modification of the filler by stearyl amine. The intercalation of the amine chains into the clay gallery gap was confirmed by the presence of some extra peaks (2928, 2846, and 1553 cm^?1) in the FTIR spectra. The clay–rubber nanocomposites were characterized by TEM and XRD. The mechanical properties were studied for all the compositions. An improvement in the mechanical properties with the degree of filler loading up to a certain level was observed. The changes in the mechanical properties, with changes in the nature and polarity of the rubbers, were explained with the help of XRD and TEM results. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1573–1585, 2004     

Molecular modeling study on surface,thermal, mechanical and gas diffusion properties of chitosan

The motivation of this work is to provide reliable and accurate modeling studies of the physical (surface, thermal, mechanical and gas diffusion) properties of chitosan (CS) polymer. Our computational efforts have been devoted to make a comparison of the structural bulk properties of CS with similar type of polymers such as chitin and cellulose through cohesive energy density, solubility parameter, hydrogen bonding, and free volume distribution calculations. Atomistic modeling on CS polymer using molecular mechanics (MM) and molecular dynamics (MD) simulations has been carried out in three dimensionally periodic and effective two dimensionally periodic condensed phases. From the equilibrated structures, surface energies were computed. The equilibrium structure of the films shows an interior region of mass density close to the value in the bulk state. Various components of energetic interactions have been examined in detail to acquire a better insight into the interactions between bulk structure and the film surface. MD simulation (NPT ensemble) has also been used to obtain polymer specific volume as a function of temperature. It is demonstrated that these V–T curves can be used to locate the volumetric glass transition temperature (T_g) reliably. The mechanical properties of CS have been obtained using the strain deformation method. Diffusion coefficients of O₂, N₂, and CO₂ gas molecules at 300 K in CS have been estimated. The calculated properties of CS are comparable with the experimental values reported in the literature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1260–1270, 2007     

Study of electrical,mechanical, and nanoscale free‐volume properties of NBR and EPDM rubber reinforced by bentonite or kaolin

The effect of Na bentonite, Ca bentonite, and kaolin fillers on the macrostructure and microstructure of acrylonitrile butadiene rubber, ethylene propylene diene rubber, and their blend (50/50) was studied through electrical and mechanical measurements, as well as with positron annihilation lifetime spectroscopy. The real part of permittivity (ε′), dielectric loss (ε″), and the crosslinking density were found to increase with increasing filler content. The increase of crosslinking density of the blend with increasing amount of fillers reflects a decrease in the equilibrium swelling up to 21.50 wt % compared with that of the unfilled blends. The mechanical investigation showed pronounced increase in the tensile strength, and in elongation at break with the addition of up to 21.50 wt % of filler. In addition, comparing between different fillers showed that the reinforcing effect of Na bentonite is more effective than Ca bentonite and kaolin but the physico‐mechanical of Ca bentonite is less than that for kaolin. The positron annihilation lifetime measurements revealed that the free‐volume properties were strongly affected by the amount and type of filler, in particular, the free‐volume fraction was dramatically decreased with increasing filler content. Furthermore, correlations were made between the free‐volume parameters and both electrical and mechanical properties. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1825–1838, 2009     

Revisiting thermoplastic polyurethane,from composition to morphology and properties

Thermoplastic polyurethanes (TPUs) are among the most versatile engineering polymers. The presence of hard and soft segments on their backbone and specific hydrogen bond interactions between the hard segments, provide TPUs with outstanding engineering properties while rendering them as very complex systems to study. Knowledge of morphology–property relationship is essential for TPUs since their thermal and mechanical behavior are directly dictated by their complicated morphology. In this research, TPU morphological features related to the hard segment content (HSC) were explored in tandem with system macroscopic properties. It was observed that TPUs display multiscale phase separated morphology with specific morphological features dependent on the HSC. At a certain critical HSC, an interconnected network of hard segments was formed which resulted in significant changes in TPU properties. This was explained in analogy with percolation phenomena in filler reinforced systems and considering the hard segments as reinforcing agent. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1553–1564     

Polymerization of propylene by metallocene and Ziegler–Natta mixed catalytic systems. Study of polypropylene properties

Propylene was polymerized with metallocene and Ziegler–Natta mixed-catalytic systems to obtain reactor blends of metallocene and Ziegler–Natta-derived propylene homopolymers. The two catalytic systems are able to act jointly, providing individual polymers with different melting and crystallization temperatures. Compatibility between the components of the mixed-catalytic systems and the influence of the components on the polymerization process and on the properties of the reactor blends were studied. Thermal, mechanical, viscoelastic, rheological, and optical properties of the blends were tested and compared with those of conventional polypropylene grades. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 3063–3072, 1998     

Mechanical properties of clay‐reinforced polyamide

Intercalated and exfoliated nanocomposites were prepared by extrusion and injection of polyamide‐6 and highly swollen or slightly swollen montmorillonite, respectively. The microstructure of the nanocomposites has been studied previously. In this article, we investigated the influence of the preferential orientation of the montmorillonite sheets on the mechanical properties of the nanocomposites. Dynamic mechanical analysis and tensile tests showed that the elastic modulus depends mainly on the filler loading. A parallel coupling could well account for the behavior of the nanocomposites. The calculated elastic and storage moduli of montmorillonite were set to 140 and 40 GPa, respectively. Compression tests were performed to study the anisotropy of the mechanical properties. The elastic modulus and flow strain were sensitive to the filler orientation. A Tandon–Weng approach was applied to consider the geometry of the filler. In all low‐deformation tests, no significant difference between intercalated and exfoliated systems was observed. Finally, the influence of the dispersion and exfoliation state of the filler on the ultimate properties of the nanocomposites (tensile tests) is discussed. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 272–283, 2002     

Dynamic light scattering from asymmetric block copolymers in neutral good solvents: Evidence of association in the disordered state

Dynamic light scattering (DLS) has been used to explore the properties of asymmetric styrene-isoprene (SI) block copolymers in concentrated solutions. Concentrations were always well below those necessary to access the order–disorder transition in neutral good solvents. The samples include SI (10-50), SI (36-9), and SIS (10-100-10), where the numerical suffixes denote the block molecular weights in kilodaltons; experimental emphasis was placed on SI (10-50). The DLS intensity correlation functions in the neutral good solvents, THF and toluene, were dominated by a slow mode that first appeared at a concentration c⁺ ≈ 4 c*, where c* is the coil overlap concentration. The decay rate of this mode scaled approximately as the third power of the scattering wavevector, and the excess scattered intensity decreased with increased scattering angle. These results were tentatively ascribed to the onset of substantial concentration fluctuations, that exhibited cylindrical, or wormlike structures. Measurements in solvents of known selectivity, dioxane and cyclohexane, and on a copolymer of the opposite composition, SI (36-9), indicated that the intermolecular association was driven by the effectively repulsive interactions between styrene and isoprene segments, rather than by solvent selectivity. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1831–1837, 1998     

Synthesis and characterization of phenyl polysiloxane modified polyurea/polyurethanes

A series of phenyl polysiloxane‐modified polyurea/polyurethanes ( SPUs ) with different silicone loadings (10, 20, 30, and 40 wt %) have been designed and synthesized. The structures of SPUs were confirmed by ¹H NMR, ¹³C NMR, and FT‐IR. The impact of phenyl polysiloxane content on the properties of SPUs was fully studied. The residual methoxy groups on silicon could help SPUs form interpenetrating networks accompanying with the residual isocyanate under moisture, which was different with the conventional moisture‐crosslinking polyurethane system. The properties of SPUs films have been fully researched by attenuated total reflection flourier transformed infrared spectroscopy, thermal analysis, tensile tests, water contact angle, X‐ray photoelectron spectroscopy, SEM, and AFM. Results indicated that the introduction of phenyl polysiloxane improved the thermal stability and remarkably increased the water contact angles accompanying with a comparable mechanical strength to the pure polyurethane. Meanwhile, it also brought out the decreased microphase separation and water absorption. The obvious surface migration has been observed in the SPUs , which changed their surface properties. Some voids were observed in all moisture curing SPUs system, but the phenyl silicone content impacted on the numbers and sizes of the voids. The phenyl groups introduced and carbon dioxide produced in the crosslinking procedure helped to form and stabilize the voids in the SPUs . © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1794–1805     

Microstructure and properties of styrene‐butadiene rubber based nanocomposites prepared from an aminosilane modified synthetic lamellar nanofiller

In this work, a novel nanocomposite series based on styrene‐butadiene rubber (SBR latex) and alpha‐zirconium phosphate(α‐ZrP) lamellar nanofillers is successfully prepared. The α‐ZrP lamellar filler is modified at the cation exchange capacity by γ‐aminopropyltrimethoxysilane and the filler surface modification is first discussed. A significant improvement of the mechanical properties is obtained by using the surface modified nanofillers. However, no modification of the gas barrier properties is observed. The impact of addition of bis(triethoxysilylpropyl)tetrasulfide (TESPT) as coupling agent in the system is discussed on the nanofiller dispersion state and on the filler–matrix interfacial bonding. Simultaneous use of modified nanofillers and TESPT coupling agent is found out with extraordinary reinforcing effects on both mechanical and gas barrier properties and the key factors at the origin of the improvement of these properties are identified. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 1051–1059     

Structure and mechanical behavior of nylon‐6 fibers filled with organic and mineral nanoparticles. I. Microstructure of spun and drawn fibers

The crystalline structure and fibrillar texture of nylon‐6 fibers filled with nanosized particles were investigated using wide‐angle and small‐angle X‐ray scattering. As‐spun fibers filled with organic nanoparticles consisting of aromatic polyamide‐like hyperbranched molecules with amine‐terminating groups exhibited strong modification of both the molecular orientation and the crystalline structure compared with that of unfilled spun fibers. Montmorillonite‐filled fibers mainly exhibited orientation improvement. The differences are discussed in terms of the rheological and nucleating effects during spinning. Drawing at 140 °C involves structural changes that resulted in the three kinds of fibers having a similar crystalline form and molecular orientation. In parallel, after significant strain‐induced changes, the microfibrillar texture of the various fibers displayed subtle differences at the ultimate stage of drawing. The changes in the fibril long period and fibril radius as a function of draw ratio are discussed in terms of the two sequential deformation processes of microfibril stretching and microfibril slipping. The occurrence of interfibrillar strain‐induced cavitation is discussed in relation to the nature of the interactions between the filler and the nylon‐6 matrix. And, finally, the mechanical properties are discussed in relation to the filler–matrix interaction. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3876–3892, 2004     

Synthesis and characterization by MALDI-TOF MS of polycyclic siloxanes derived from p-substituted novolac resins by MALDI-TOF MS

Novel polycyclic siloxane resins were prepared from phenol-formaldehyde novolac type resins by reacting them with dialkyl or diaryl dichlorosilanes under anhydrous and high dilution conditions. The formation of polycyclic species was confirmed by the detection of absolute masses by MALDI-TOF mass spectrometry. ¹H- and ²⁹Si-NMR confirmed the substitutions of phenolic hydroxy groups by siloxane bonds. Curing studies were conducted on the polycyclic siloxane resins as well as on the polycyclic siloxane resins incorporated into two types of polysiloxane gums. A trace amount of potassium hydroxide was used as a catalyst for the crosslinking of these systems. The blend of polysiloxane with 30 wt % polycyclic siloxane was found to be stable at the curing temperature. Differential scanning calorimetry and thermogravimetric analysis techniques were used to study the thermal profiles of these systems. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A Polym. Chem. 36: 2429–2437, 1998     

Brillouin scattering studies of polymeric nanostructures *

For a range of applications, polymers are now being patterned into nanometer‐sized features. In these applications, the robust mechanical properties of the nanostructures are critical for performance and stability. Brillouin light scattering is presented as a nondestructive, noncontact tool used to quantify the elastic constants in such nanostructures. We demonstrate this through a series of thin films and parallel ridges and spacings (gratings) with ridge widths ranging from 180 to 80 nm. For the set of films and structures presented here, the room‐temperature elastic moduli did not change with decreasing film thickness or grating ridge width, and this implied that one‐dimensional and two‐dimensional confinement‐induced changes of the mechanical properties were not significant down to feature sizes of 80 nm. Additionally, Brillouin spectra of submicrometer gratings revealed new modes not present in the spectra of thin films. The origin of these new modes remains unclear. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1106–1113, 2004