The effect of low earth orbit atomic oxygen exposure on phenylphosphine oxide-containing poly(arylene ether)s

Unoriented thin films of phenylphosphine oxide-containing poly(arylene ether)s were exposed to low Earth orbit aboard the space shuttle Atlantis (STS-51) as part of a flight experiment designated Limited Duration Candidate Exposure (LDCE 4–5). The samples were exposed to primarily atomic oxygen (!10,\7×10¹⁹ atoms/cm²). Based on post-flight analyses using atomic force microscopy, X-ray photoelectron spectroscopy, gel permeation chromatogrpahy and weight loss data, it was proposed that atomic oxygen exposure of these materials produces a phosphate layer at the surface of the samples, apparently by the reaction of atomic oxygen with the phosphorus in the polymer backbone. Ground-based oxygen plasma exposure experiments have previously shown that this phosphate layer provides a barrier against further attack by atomic oxygen [1]. The results obtained from these analyses compare favorably with those obtained from samples exposed to an oxygen plasma in ground-based exposure experiments [1]. © 1998 John Wiley & Sons, Ltd.     

Poly(arylene ether)s and poly(arylene thioether)s containing the 1,2-dihydro-4-phenyl(2H)- phthalazinone moiety

A series of new high molecular weight poly(arylene ether)s containing the 1,2-dihydro-4-phenyl(2H)phthalazinone moiety have been synthesized. The inherent viscosities of these polymers are in the range of 0.33–0.64 dL/g. They are amorphous and readily soluble in chloroform, DMF, and DMAc. The glass transition temperatures of the polymers range from 241 to 320°C and the 5% weight loss temperatures in nitrogen atmosphere range from 473 to 517°C. The hydroxy group in the monomer 1,2-dihydro-4-(4-hydroxyphenyl)(2H)phthalazin-1-one has been selectively transformed into the N,N′-dimethylthiocarbamate group, which was then rearranged to give the S-(N,N′-dimethylcarbamate) group via the Newman–Kwart rearrangement reaction. A series of poly(arylene thioether)s containing the 1,2-dihydro-4-phenyl(2H)phthalazinone moiety have also been synthesized via two types of reactions, a N C coupling reaction and a one-pot reaction between the S-(N,N′-dimethylcarbamate) and activated dihalo compounds, in diphenyl sulfone in the presence of a cesium carbonate and calcium carbonate mixture. These poly(arylene thioether)s also have high glass transition temperatures (ranging from 217–303°C) and high thermal stabilities. Compared with their poly(ether) analogs, the poly(arylene thioether)s have glass transition temperatures several degrees lower, which is attributed to the more flexible C S C bonds. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36 : 455–460, 1998     

Synthesis and characterization of new poly(arylene ether)s containing heterocyclic units. II.

A series of new poly(arylene ether)s, containing naphthalene, pyridine, and quinoline units have been prepared by solution condensation polymerization. The synthesis involves nucleophilic displacement of aromatic dihalides with aromatic potassium bisphenates in an anhydrous dipolar aprotic solvent at elevated temperatures. The polymers, having inherent viscosity from 0.24 to 1.32 dL/g, were obtained in quantitative yield, have excellent thermal stability as shown by 10% weight loss temperatures in nitrogen and air (above 450 and 430°C, respectively) and high glass transition temperatures (in the range of 150–220°C). The introduction of quinoline moieties in the polymer backbone positively influences the thermal properties, such as high T_g/T_m ratios. © 1995 John Wiley & Sons, Inc.     

Ring-opening polymerization of macrocyclic aryl ether ketone oligomers containing the 1,2-dibenzoylbenzene moiety

Facile ring-opening polymerization of cyclic aryl ether oligomers containing the 1,2-dibenzoylbenzene moiety to form high molecular weight linear polymers in the presence of a nucleophilic initiator is described. The polymerization can be initiated in the melt in the presence of a nucleophilic initiator such as potassium carbonate, cesium fluoride, and alkali phenoxides. Various alkali phenoxides were investigated as potential nucleophilic initiators. The polymerization reaction rate in the melt increases in the order of K⁺ > Na⁺ > Cs⁺, and in the order of ⁻OPhPhO⁻ > PhO⁻ > PhOPhO⁻ > PhPhO⁻. However, the polymerization in an aprotic dipolar solvent is faster in the presence of cesium phenoxide than in the presence of potassium phenoxide. Polymerization of the cyclic oligomers in solution demonstrates that the ring-opening polymerization proceeds via a chain-growth mechanism and involves a transetherification reaction between linear and cyclic aryl ether oligomers. The ring-chain equilibrium is much more favorable towards linear polymers. Since little or no ring strain exists in the cyclic system, the transetherification reactions are indiscriminate with regards to cyclic or linear chains and the interchain equilibration is also a facile process during polymerization. This intermolecular transetherification has been demonstrated by using low molecular weight aryl ethers to control the molecular weight of the polymer formed via ring-opening polymerization. © 1996 John Wiley & Sons, Inc.     

Phosphonyl/hydroxyl hydrogen bonding–induced miscibility of poly(arylene ether phosphine oxide/sulfone) statistical copolymers with poly(hydroxy ether) (phenoxy resin): Synthesis and characterization

High molecular weight bisphenol A or hydroquinone‐based poly(arylene ether phosphine oxide/sulfone) homopolymer or statistical copolymers were synthesized and characterized by thermal analysis, gel permeation chromatography, and intrinsic viscosity. Miscibility studies of blends of these copolymers with a (bisphenol A)‐epichlorohydrin based poly(hydroxy ether), termed phenoxy resin, were conducted by infrared spectroscopy, dynamic mechanical analysis, and differential scanning calorimetry. All of the data are consistent with strong hydrogen bonding between the phosphonyl groups of the copolymers and the pendent hydroxyl groups of the phenoxy resin as the miscibility‐inducing mechanism. Complete miscibility at all blend compositions was achieved with as little as 20 mol % of phosphine oxide units in the bisphenol A poly(arylene ether phosphine oxide/sulfone) copolymer. Single glass transition temperatures (T_g) from about 100 to 200°C were achieved. Replacement of bisphenol A by hydroquinone in the copolymer synthesis did not significantly affect blend miscibilities. Examination of the data within the framework of four existing blend T_g composition equations revealed T_g elevation attributable to phosphonyl/hydroxyl hydrogen bonding interactions. Because of the structural similarities of phenoxy, epoxy, and vinylester resins, the new poly(arylene ether phosphine oxide/sulfone) copolymers should find many applications as impact‐improving and interphase materials in thermoplastics and thermoset composite blend compositions. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1849–1862, 1999     

Synthesis,characterization, and comparison of properties of new fluorinated poly(arylene ether)s containing phthalimidine moiety in the main chain

Four new poly(arylene ether)s have been prepared by the reaction of N‐phenyl‐3,3‐bis(4‐hydroxyphenyl)phthalimidine (PA) with four different perfluoroalkylated monomers namely 1,3‐bis(4′‐fluoro‐3′‐trifluoromethyl benzyl) benzene, 4,4′‐bis(4′‐fluoro‐3′‐trifluoromethyl benzyl) biphenyl, 2,6‐bis(4′‐fluoro‐3′‐trifluoromethyl benzyl) pyridine, and 2,5‐bis(4′‐fluoro‐3′‐trifluoromethyl benzyl) thiophene. The poly(arylene ether)s were characterized by different spectroscopic, thermal, mechanical, and electrical techniques. The poly(arylene ether) containing quadriphenyl unit in the main chain showed very high glass transition temperature of 291°C and outstanding thermal stability upto 556°C for 10% weight loss under a 4:1 nitrogen:oxygen mixture. The polymers were soluble in a wide range of organic solvents. Transparent thin films of these polymers exhibited tensile strengths upto 75 MPa and elongation at break upto 32%. The films of these polymers showed low water absorption of 0.26%. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis and optical properties of fluorinated poly(arylene ether phosphine oxide)s

Fluorinated dihydroxy phosphine oxide monomers were synthesized via chlorination, Grignard, and demethylation techniques. The prepared monomer was successfully polymerized with each of the three perfluorinated monomers (decafluorobiphenyl, decafluorobenzophenone, and pentafluorophenylsulfide) by nucleophilic aromatic substitution. The average molecular weight ranged between 7800 and 14,900 g/mol. The glass‐transition temperatures of the polymers were registered in the range of 185–235 °C, and all the polymers exhibited high thermal stability up to 326–408 °C. The results of the refractive‐index measurements indicated control of the refractive index between 1.5181 and 1.5536 and an optical loss of 0.53 dB/cm at 1550 nm. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1497–1503, 2003     

Synthesis and proton conductivities of phosphonic acid containing poly‐(arylene ether)s

A novel phosphonic acid containing bisphenol was successfully synthesized from phenolphthalein and m‐aminophenylphosphonic acid. A series of homo‐ and copoly‐(arylene ether)s containing phosphonic acid groups were prepared by solution nucleophilic polycondensation. These phosphonic acid containing polymers can readily be dissolved in common organic solvents, such as dimethyl sulfoxide, N‐methyl‐2‐pyrrolidinone, and N‐cyclohexylpyrrolidinone, and can be cast into tough and smooth films. The presence of phosphonic acid pendants in the poly‐(arylene ether)s was confirmed by NMR, matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry, and conductivity measurements. This is the first report on the attachment of phenylphosphonic acid groups as side chains to aromatic polyethers. These poly‐(arylene ether)s had very high glass‐transition temperatures ranging from 254 to >315 °C and high molecular weights. The conductivities of the synthesized polymers were analyzed by the Cole–Cole method, and they ranged from 10^?5 to 10^?6 Scm^?1. The synthesized polymers also exhibited good solution processability. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3218–3226, 2001     

Controlled sulfonation of poly(arylene ether sulfone)s and poly(arylene ether ketone)s with different molecular structures for polymer electrolyte membranes

Poly(arylene ether sulfone) copolymers derived from 9,9-bis(4-hydroxyphenyl)fluorene, bisphenol S and 4,4′-difluorodiphenylsulfone and poly(arylene ether ketone) copolymers derived from 4-phenoxybiphenyl, diphenyl ether and isophthaloyl chloride were prepared as precursor polymers for sulfonation reaction in which sulfonic groups are introduced quantitatively into specified positions. Sulfonation reaction for these two series of copolymers by concentrated sulfuric acid was successfully carried out to give sulfonated polymers with controlled positions and degree of sulfonation. Thermal stability, moisture absorption and proton conductivity for these two series of copolymers were measured and the results were compared to those of perfluorosulfonic acid polymers.     

One-pot method of preparing novel macrocyclic(thio arylene) oligomers

A series of macrocyclic(thio arylene) oligomers were synthesized under high dilution conditions by reacting diphenyl ether, diphenyl, diphenyl disulfide or diphenyl methane with dichloro disulfide in the presence of trace amount of iron powder by a one-step method. The composition of these macrocyclic oligomers was analyzed by MALDI-TOF technology, and the experimental results showed that the cyclics were a mixture with repeating units separated by one to seven sulfur atoms. These macrocyclics can undergo ring-opening polymerization to form linear polymers under mild conditions. The glass transition temperatures of produced polymers varied with the sulfur content.     

Gas transport properties of novel poly(arylene ether ketone)s containing dibenzoylbiphenyl and benzonaphthone moieties

In this work we present the results from studies on novel poly(arylene ether ketone)s, including gas permeability, wide-angle x-ray diffraction (WAXD), and dynamic mechanical analysis (DMA). Poly(arylene ether ketone)s containing 2,2′- and 3,3′-dibenzoylbiphenyl (DBBP) moieties were characterized to study the effect of biphenyl substitution on gas transport properties. Gas permeabilities of naphthalene-containing poly(arylene ether ketone)s were also measured. Higher permeabilities were observed for polymers prepared with 6F-BPA, compared to 9,9-bis(4-hydroxyphenyl)fluorene (HPF). The naphthalene-containing polymers exhibited higher permeabilities than the DBBP polymers, except for a polymer having the 2,2′-DBBP and tetramethylbiphenyl moieties. Based on our work, and results reported in the literature, the 3,3′-DBBP polymers showed the lowest permeabilities for DBBP-containing poly-(arylene ether ketone)s. The low permeabilities are due to more efficiently packed chains brought on by greater flexibility of the backbone, compared to the other polymers studied. DMA studies confirmed the higher barriers to rotation which are believed to be responsible for 2,2′-DBBP polymers having similar selectivities compared to 3,3′-DBBP polymers. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 425–431, 1998     

Poly(arylene ether)s,poly(arylene thioether)s,and poly(arylene sulfone)s derived from a dihydroxy(imidoarylene) monomer

Novel poly(arylene ether)s, poly(arylene thioether)s, and poly(arylene sulfone)s were synthesized from the dihydroxy(imidoarylene) monomer 1 . The syntheses of poly(arylene ether)s were carried out in DMAc in the presence of anhydrous K₂CO₃ by a nucleophilic substitution reaction between the bisphenol and activated difluoro compounds. Poly(arylene thioether)s were synthesized according to the recently discovered one-pot polymerization reaction between a bis(N,N′-dimethyl-S-carbamate) and activated difluoro compounds in the presence of a mixture of Cs₂CO₃ and CaCO₃. The bis(N,N′-dimethyl-S-carbamate) 3 was synthesized by the thermal rearrangement reaction of bis(N,N′-dimethylthiocarbamate) 2 , which was synthesized from 1 by a phase-transfer catalyzed reaction. The poly(arylene thioether)s were further oxidized to form poly(arylene sulfone)s, which would be very difficult, if not impossible, to synthesize by other methods. All of the polymers described have extremely high T_gs and thermal stability as determined from DSC and TGA analysis. Poly(arylene sulfone)s have the highest T_gs and they are in the range of 298–361°C. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1201–1208, 1998     

Self-Crosslinkable poly(arylene ether)s containing pendent phenylenetriazene groups

Self-crosslinkable poly(arylene ether)s 6 , and 8 , containing pendent triazene groups were prepared by nucleophilic substitution reaction of poly(arylene ether)s 5 , and 7 , respectively, with 1-[4-(4-hydroxyphenoxy)phenylene]triazenes, 4 , in the presence of potassium carbonate in N,N-dimethylacetamide. A series of triazenes 4 containing various substituents have been synthesized. Self-crosslinkable polymer 6e containing phenyl-substituted triazene pendants can be crosslinked at 215°C, which is about 40°C lower than the glass transition temperature of the virgin base polymer 5 . The degree of crosslinking can be tailored by varying the concentration of the pendent phenylenetriazene groups in the polymer. After curing, the flexible polymer films (ca. 10 μm thick) exhibit high gel contents, increased glass transition temperatures, improved resistance to organic solvents, and little change in dielectric constant and thermal stability. These self-crosslinkable poly(arylene ether)s are potential candidates for electronic applications. © 1994 John Wiley & Sons, Inc.     

Copolymerization of elemental sulfur with cyclic(arylene disulfide) oligomers

Copolymerization reactions between cyclic(arylene disulfide) oligomers were studied. The cyclic disulfide oligomers derived from 4,4′-isopropylidene bisbenzenethiol gave soluble polysulfanes via copolymerization with S₈. The copolymerization reactions were studied both in solution and melt by GPC and NMR. Solution copolymerization reactions can only form polysulfanes with up to three to four sulfur linkages; however, melt copolymerization reactions gave polysulfanes with up to seven sulfur linkages (average). The melt copolymerization reactions between cyclic disulfide oligomers derived from 4,4′-thiobis(benzenethiol) and S₈ were studied using DSC, TGA, and DMTA. With increasing contents of sulfur in the polysulfanes, T_gs, 5% weight losses by TGA, and tan δ decreased. With seven sulfur linkages in the polymer, it is a rubber with a T_g of 12°C, a 5% weight loss by TGA of 249°C, and tan δ of 44°C, respectively. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2961–2968, 1997     

Synthesis and characterization of a novel AB2 monomer and corresponding hyperbranched poly(arylene ether phosphine oxide)s

A novel AB₂ monomer, 4‐(fluorophenyl)‐4′,4″‐(bishydroxyphenyl) phosphine oxide, was synthesized. The monomer was successfully polymerized to a modest molecular weight with various catalysts, including K₂CO₃ and Cs₂CO₃/Mg(OH)₂. Hyperbranched polymers exhibited exceptionally high thermal stability and solubility in conventional polar organic solvents and basic water solutions. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3736–3741, 2000     

A novel class of organosoluble poly(arylene ether nitrile) copolymers containing methyl substituent and cardo xanthene moiety

9,9‐Bis(3‐methyl‐4‐hydroxyphenyl)xanthene (BMHPX) was synthesized in 72% yield by a HCl/ZnCl₂‐catalyzed condensation reaction of xanthenone with excess o‐cresol. Based on this new bisphenol monomer, a series of poly(arylene ether nitrile) (PAEN) and PAEN copolymers containing methyl substituent and cardo xanthene moiety were prepared by the nucleophilic substitution reaction of 2,6‐difluorobenzonitrile (DFBN) with BMHPX and with varying mole proportions of BMHPX to hydroquinone (HQ) (100/0–40/60) using N‐methyl‐2‐pyrrolidone (NMP) as solvent in the presence of anhydrous potassium carbonate. These polymers had inherent viscosities between 0.54 and 0.72 dl/g, and their weight‐average molecular weights and number‐average molecular weights were in the range of 32,600–36,400 and 17,300–18,300, respectively. All PAENs were amorphous and were soluble in dipolar aprotic solvents such as NMP and N,N‐dimethylacetamide (DMAc), and even in THF and chloroform at room temperature. The resulting polymers showed glass transition temperatures (T_g's) between 213–226°C, and the T_g values of the copolymers were found to increase with increase of the BMHPX units content in the polymer. Thermogravimetric studies showed that all the polymers were stable up to 404°C, with 10% weight loss temperatures ranging from 444 to 455°C, and char yields of 52–58% at 700°C in nitrogen. All new PAENs could be cast into transparent, strong, and flexible films with tensile strengths of 102–120 MPa, elongations at break of 14–18%, and tensile moduli of 3.3–3.7 GPa. Copyright © 2011 John Wiley & Sons, Ltd.     

Co‐poly(aryl ether sulfone)s containing phthalimidine moiety in the main chain

Several new co‐poly(arylene ether sulfone)s have been prepared by the reaction of 4,4′‐fluorodiphenyl sulfone (FDS) with different bisphenols namely 4,4′‐isopropylidenediphenol (BPA), 4,4′‐hexafluoroisopropylidenediphenol (6F‐BPA), and N‐phenyl‐3,3‐bis(4‐hydroxyphenyl)phthalimidine(PA). The homo‐poly(arylene ether sulfone)s are named as 1a, 2a, and 3a. The copolymers namely 2b, 2c, 2d and 3b, 3c, 3d have been prepared, respectively, on reaction of FDS with BPA or 6F‐BPA using different molar ratios of PA such as 25, 50, and 75. The poly(aryl ether sulfone)s 1a containing PA unit in the main chain showed a very high glass transition temperature of 280°C and an outstanding thermal stability up to 510°C for 5% weight loss under synthetic air. Depending on the mole% of PA, the glass transition temperatures of the copolymers can be varied. The polymers were soluble in a wide range of organic solvents. Transparent thin films of these polymers exhibited tensile strengths upto 84 MPa and Young's modulus up to 3.16 GPa. The films of these polymers showed low water absorption of 0.24%. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis and thermal properties of poly(arylene ether ketone)s containing phthalazinone moieties

A series of novel poly(arylene ether ketone)s were synthesized from the reaction of hydroquinone and 4-(4-hydroxyphenyl)-2,3-phthalazin-1-one with 4,4′-difluorobenzophenone in N-cyclohexylpyrrolidinone containing anhydrous potassium carbonate. The polymers exhibited high glass transition temperatures together with excellent thermooxidative stability. The chain structure of these polymers was studied by means of differential scanning calorimetry (DSC), wide-angle X-ray diffraction techniques (WAXD), and matrix-assisted laser desorption/ionization time of flight mass spectrometry (MALDI-TOF-MS). The experimental results indicated that these “as-made” copoly(aryleneketone)s containing hydroquinone moieties exhibited a block chain structure with segments which mainly consisted of hydroquinone and 4,4′-difluorobenzophenone. These chain segments resulted in crystallites in the polymers although they are thermodynamically unstable. The polymers showed thermal properties comparable to commercial PEEK, but the conditions for synthesis are much milder. The glass transition temperatures and solubilities of the copoly(arylene ketone)s tended to increase with increasing phthalazinone moiety content, while the crystallite melting points and crystallinity appeared to decrease. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1781–1788, 1999     

Free volume in glassy poly(arylene ether ketone)s

Amorphous polyarylene ether ketones were examined in the glassy state by positron annihilation lifetime spectroscopy (PALS) and in the melt by standard rheological techniques. Specimens were well-characterized fractions of two isomeric structures. PALS clearly shows that the polymer with meta linkages in its backbone contains larger voids (> 0.25 nm radius). Thus despite their similar bulk densities, the two materials must pack very differently on a local scale. On the other hand, the free volumes inferred from the WLF treatment of melt viscosity data are practically identical in both materials ca. 4% at T_g. The comparison between techniques sheds some light on the distribution of free volume. © 1992 John Wiley & Sons, Inc.     

Synthesis of thermally crosslinkable fluorine‐containing poly(arylene ether ketone)s—II. Propargyl ether terminated poly(arylene ether ketone)s

Novel thermally crosslinkable fluorine‐containing poly(arylene ether ketone)s comprised of 2,3,5, 6‐tetrafluoro‐1,4‐phenylene moiety were synthesized by the termination of polymer chain ends with propargyl ether groups in order to improve solvent resistance. Crosslinking reaction occurred over 250°C through the formation of both chromen ring and polyene structure. This structure change brought about not only the outstanding solvent resistance but also the increase in glass transition temperature (T_g). The cured films also exhibited excellent thermal stability, transparency and hydrophobicity derived from fluorine atoms. Copyright © 2004 John Wiley & Sons, Ltd.