Microphase‐separated structure of 1,3‐cyclohexadiene/butadiene triblock copolymers and its effect on mechanical and thermal properties

We report the effect of microphase‐separated structure on the mechanical and thermal properties of several poly(1,3‐cyclohexadiene‐block‐butadiene‐block‐1,3‐cyclohexadiene) triblock copolymers (PCHD‐block‐PBd‐block‐PCHD) and of their hydrogenated derivatives: poly(cyclohexene‐block‐ethylene/butylene‐block‐cyclohexene) triblock copolymers (PCHE‐block‐PEB‐block‐PCHE). Both mechanical strength and heat‐resistant temperature (ex. Vicat Softening Temperature: VSPT) tended to increase with an increase in the 1,3‐cyclohexadiene (CHD)/butadiene ratio. On the other hand, heat resistance of the hydrogenated block copolymer was found to be higher than that of the unhydrogenated block copolymer. However, the mechanical strength was lower than those of the unhydrogenated block copolymer with the same ratio of CHD to butadiene. To clarify the relationship between the higher order structures of those block copolymers and their properties, we observed the microphase‐separated structure by transmission electron microscope (TEM). Hydrogenated block copolymers were found to have more finely dispersed microphase‐separated structures than those of the unhydrogenated block copolymers with the same CHD/Bd ratios through the use of TEM and the small‐angle X‐ray scattering (SAXS) technique. Those results indicated that the segregation strength between the PCHE block sequence and the PEB block sequence increased, depending on hydrogenation of the unhydrogenated precursor. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 13–22, 2001     

Copolymerization of propylene with 1,3‐butadiene using isospecific zirconocene catalysts

Poly(propylene‐ran‐1,3‐butadiene) was synthesized using isospecific zirconocene catalysts and converted to telechelic isotactic polypropylene by metathesis degradation with ethylene. The copolymers obtained with isospecific C₂‐symmetric zirconocene catalysts activated with modified methylaluminoxane (MMAO) had 1,4‐inserted butadiene units ( 1,4‐BD ) and 1,2‐inserted units ( 1,2‐BD ) in the isotactic polypropylene chain. The selectivity of butadiene towards 1,4‐BD incorporation was high up to 95% using rac‐dimethylsilylbis(1‐indenyl)zirconium dichloride (Cat‐A)/MMAO. The molar ratio of propylene to butadiene in the feed regulated the number‐average molecular weight (M_n) and the butadiene contents of the polymer produced. Metathesis degradations of the copolymer with ethylene were conducted with a WCI₆/SnMe₄/propyl acetate catalyst system. The ¹H NMR spectra before and after the degradation indicated that the polymers degraded by ethylene had vinyl groups at both chain ends in high selectivity. The analysis of the chain scission products clarified the chain end structures of the poly(propylene‐ran‐1,3‐butadiene). © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5731–5740, 2007     

Poly(1,3-cyclohexadiene-alt-α-fluoroacrylonitrile): Synthesis and structural analysis of a new alternating copolymer

Poly(1,3-cyclohexadiene-alt-α-fluoroacrylonitrile) [poly(1,3-CHD/α-FAN)], an alternating copolymer of α-fluoroacrylonitrile and 1,3-cyclohexadiene has been prepared in bulk using varied monomer feed ratios and AIBN as initiator at 65°C. Elemental and ¹H-NMR analyses indicate that the copolymer contains an equimolar composition of α-FAN and 1,3-CHD as observed for alternating copolymers with donor-acceptor polymerizations. A 2-D ¹H-COSY NMR experiment indicates that the copolymer contains 1,4-linkages across the cyclohexene unit while more reliable ¹³C-NMR spectra suggests the copolymer to contain both 1,2- and 1,4-linkages. Poly(1,3-CHD/α-FAN) exhibits improved thermal stability relative to the alternating copolymer of 1,3-CHD and α-chloroacrylonitrile due to a higher resistance to HF elimination relative to HCl elimination.     

Anionic polymerization of 1,3‐cyclohexadiene with alkyllithium/amine system in an aromatic hydrocarbon solvent: Predominant formation of 1,2‐addition product

Steric hindrance of the amine strongly affected the formation of the dominant 1,2‐addition product from the anionic polymerization of 1,3‐cyclohexadiene (1,3‐CHD) initiated by the alkyllithium (RLi)/amine system in an aromatic hydrocarbon solvent. 1,2‐Cyclohexadiene (1,2‐CHD)/1,4‐cyclohexadiene (1,4‐CHD) unit molar ratios from 85/15 to 93/7 were obtained using an RLi/N,N,N′,N′‐tetramethylethylenediamine (TMEDA) system in toluene. The C? Li bonds of poly(1,3‐cyclohexadienyl)lithium (PCHDLi)/TMEDA complex in toluene appeared to be strongly polarized with small steric hindrance. Intermolecular forces contributing to the aggregation were strong for high‐molecular‐weight poly(1,3‐cyclohexadiene) (PCHD) consisting of almost all 1,2‐CHD units. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6604–6611, 2008     

Linear pentablock quintopolymers (l‐SIDMV) with five incompatible blocks: Polystyrene,polyisoprene‐1,4, poly(dimethylsiloxane), poly(tert‐butyl methacrylate), and poly(2‐vinylpyridine)

Three linear pentablock quintopolymers (l‐SIDMV), where S is polystyrene (PS), I polyisoprene‐1,4 (PI), D poly(dimethylsiloxane) (PDMS), M poly(tert‐butyl methacrylate) (PtBuM), and V poly(2‐vinylpyridine) (P2VP), were synthesized by anionic polymerization high vacuum techniques. The approach involves the following: (a) The synthesis of living triblock terpolymer PS‐b‐PI‐b‐PDMSLi and diblock copolymer P2VP‐b‐PtBuMK by sequential polymerizations of the corresponding monomers with sec‐BuLi and benzyl potassium, respectively; and (b) The selective linking of the living triblock terpolymer with the chlorosilane group of 2‐(chloromethylphenyl)ethyldimethylchlorosilane (CMPDMS), followed by linking of the living block copolymer with the remaining chloromethyl group of CMPDMS. Molecular characterization carried out by size exclusion chromatography, membrane osmometry, solution (in CDCl₃ or d₈‐toluene) and solid‐state ¹H‐NMR spectroscopy indicated a high degree of molecular and compositional homogeneity. Differential scanning calorimetry results on the precursors and final polymers were discussed. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3938–3946, 2008     

Syntheses and characterizations of poly[2‐(dimethylamino)ethyl methacrylate]–poly(propylene oxide)–poly[2‐(dimethylamino)ethyl methacrylate] ABA triblock copolymers

A novel, near‐monodisperse, well‐defined ABA triblock copolymer, poly[2‐(dimethylamino)ethyl methacrylate]‐b‐poly(propylene oxide)‐b‐poly[2‐(dimethylamino)ethyl methacrylate], was synthesized via oxyanion‐initiated polymerization. The initiator was a telechelic‐type potassium alcoholate prepared from poly(propylene glycol) and KH in dry tetrahydrofuran. The copolymers produced were characterized by Fourier transform infrared, ¹H NMR, and gel permeation chromatography (GPC). GPC and ¹H NMR analyses showed that the products obtained were the desired copolymers, with narrow molecular weight distributions (ca. 1.09–1.11) very close to that of the original poly(propylene glycol). ¹H NMR, surface tension measurements, and dynamic light scattering all indicated that the triblock copolymer led to interesting aqueous solution behaviors, including temperature‐induced micellization and very high surface activity. © 2002 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 624–631, 2002; DOI 10.1002/pola.10144     

Synthesis of poly(p‐phenylene)‐poly(4‐diphenylaminostyrene) bipolar block copolymers with a well‐controlled and defined polymer chain structure

A poly(p‐phenylene) (PPP)‐poly(4‐diphenylaminostyrene) (PDAS) bipolar block copolymer was synthesized for the first time. A prerequisite prepolymer, poly(1,3‐cyclohexadiene) (PCHD)‐PDAS binary block copolymer, in which the PCHD block consisted solely of 1,4‐cyclohexadiene (1,4‐CHD) units, was synthesized by living anionic block copolymerization of 1,3‐cyclohexadiene and 4‐diphenylaminostyrene. To obtain the PPP‐PDAS bipolar block copolymer, the dehydrogenation of this prepolymer with quinones was examined, and tetrachloro‐1,2‐(o)‐benzoquinone was found to be an appropriate dehydrogenation reagent. This dehydrogenation reaction was remarkably accelerated by ultrasonic irradiation, effectively yielding the target PPP‐PDAS bipolar block copolymer. The hole and electron drift mobilities for PPP‐PDAS bipolar block copolymer were both on the order of 10^?3 to 10^?4 cm²/V·s, with a negative slope when plotted against the square root of the applied field. Therefore, this bipolar block copolymer was found to act as a bipolar semi‐conducting copolymer. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Dehydrogenation of poly(1,3‐cyclohexadiene)–polystyrene binary block copolymers

The dehydrogenation of poly(1,3‐cyclohexadiene)–polystyrene binary block copolymers obtained by anionic copolymerization with alkyllithium/amine systems was investigated for the first time. The dehydrogenation of the poly(1,3‐cyclohexadiene) block, which was composed of 1,2‐cyclohexadiene (1,2‐CHD) and 1,4‐cyclohexadiene (1,4‐CHD) units, was strongly affected by the polymer chain structure. The existence of 1,2‐CHD units prevented the dehydrogenation of the poly(1,3‐cyclohexadiene) block in the binary block copolymer. The rate of dehydrogenation was fast on a long sequence of 1,4‐CHD units, whereas it was relatively slow for 1,2‐CHD/1,4‐CHD (≈1/1) unit sequences. The bonding of the polystyrene block to the polymer chain effectively improved not only the rate of dehydrogenation of a long sequence of 1,4‐CHD units but also that of the polymer chain with a high content of 1,2‐CHD units. The dehydrogenation of a poly(1,3‐cyclohexadiene) block containing a small number of 1,2‐CHD units progressed via step‐by‐step reactions. The dehydrogenation of a long sequence of 1,4‐CHD units proceeded as the first step. Subsequently, in the second step, the 1,2‐CHD/1,4‐CHD (≈1/1) unit sequences remaining in the polymer chain were dehydrogenated. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3526–3537, 2006     

Poly(ϵ‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ϵ‐caprolactone) triblock copolymers: Synthesis and self‐assembly in aqueous solutions

Nontoxic and biodegradable poly(?‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(?‐caprolactone) triblock copolymers were synthesized by the solution polymerization of ?‐caprolactone in the presence of poly(ethylene glycol). The chemical structure of the resulting triblock copolymer was characterized with ¹H NMR and gel permeation chromatography. In aqueous solutions of the triblock copolymers, the micellization and sol–gel‐transition behaviors were investigated. The experimental results showed that the unimer‐to‐micelle transition did occur. In a sol–gel‐transition phase diagram obtained by the vial‐tilting method, the boundary curve shifted to the left, and the gel regions expanded with the increasing molecular weight of the poly(?‐caprolactone) block. In addition, the hydrodynamic diameters of the micelles were almost independent of the investigated temperature (25–55 °C). The atomic force microscopy results showed that spherical micelles formed at the copolymer concentration of 2.5 × 10^?4 g/mL, whereas necklace‐like and worm‐like shapes were adopted when the concentration was 0.25 g/mL, which was high enough to form a gel. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 605–613, 2007     

Synthesis of a triblock copolymer: Poly(ethylene glycol)‐poly(alkylene phosphate)‐poly(ethylene glycol) as a modifier of CaCO3 crystallization

Triblock copolymer poly(ethylene glycol)‐poly(alkylene phosphate)‐poly(ethylene glycol) was prepared by first reacting hexamethylene glycol with dimethyl‐H‐phosphonate at conditions of transesterification and then replacing the CH₃OP(O)(H)O‐… end‐groups by monomethyl ether of poly(ethylene glycol). The course of reaction was studied by ³¹P NMR indicating complete conversion. After oxidation the poly(alkylene H‐phosphonate was converted into the final triblock polyphosphate. This triblock copolymer was used as a modifier of CaCO₃ crystallization. Unusual semi open empty spheres resulted, composed of small crystallites of the size (diameter) equal to 40–90 nm. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 650–657, 2005     

Excited-State dynamics of conjugated polycarbosilane oligomers with branched dimethyl or diphenyl group

Dimethyl or diphenyl branched conjugated polycarbosilane oligomers in solutions, including poly[[1,4-bis(thiophenyl)buta-1,3-diyne]-alt-(dimethylsilane)], poly[[1,4-bis(thiophenyl)buta-1,3-diyne]-alt-(diphenylsilane)], poly[[1,4-bis(phenyl)buta-1,3-diyne]-alt-(dimethylsilane)], and poly[[1,4-bis(phenyl)buta-1,3-diyne]-alt-(diphenylsilane)], were investigated by steady-state and picosecond time-resolved spectroscopies to elucidate the effect of silicon-atom introduction into the π-conjugated copolymer backbone and the substitution of the aromatic phenyl group on the silicon atom. The introduction of silicon atoms into π-conjugated copolymer backbones induces slow decay emission components with lifetimes of about 450 ps in addition to π–π* local excited-state relaxations in the time-resolved fluorescence decay profiles. The diphenyls, which are branched in the silicon atoms, bring about broad, structureless emission bands in the low-frequency region of the steady-state fluorescence spectra. However, such broad bands do not occur in the case of dimethyl branched conjugated polycarbosilane oligomers. The time-resolved and solvent-dependent studies of these bands imply that the excited-state dynamics of diphenyl branched conjugated polycarbosilane oligomers can be related to an intramolecular charge-transfer dynamics through an inductive and (d-p) π-conjugation effect between the π-conjugated backbone and the branched phenyl ring. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2901–2908, 1999     

Effect of backbone structures on photovoltaic properties in naphthodithiophene‐based copolymers

A “zigzag” naphthodithiophene‐based copolymer, poly[4,9‐bis(2‐ethylhexyloxy)naphtho[1,2‐b:5,6‐b′]dithiophene‐2,7‐diyl‐alt‐1,3‐(5‐heptadecan‐9‐yl)‐4H‐thieno[3,4‐c]pyrrole‐4,6‐dione] (P1) is synthesized and its properties are compared to “linear” naphthodithiophene‐based copolymer, poly[4,9‐bis(2‐ethylhexyloxy)naphtho[2,3‐b:6,7‐d′]dithiophene‐2,7‐diyl‐alt‐1,3‐(5‐heptadecan‐9‐yl)‐4H‐thieno[3,4‐c]pyrrole‐4,6‐dione] (P2). The field‐effect carrier mobilities and the optical, electrochemical, and photovoltaic properties of the copolymers are systematically investigated. The results suggest that the backbone of the copolymer structure significantly influences the band gap, electronic energy levels, carrier mobilities, and photovoltaic properties of the resultant thin films. In this work, the zigzag naphtho[1,2‐b:5,6‐b′]dithiophene‐based copolymer displays a good hole mobility and a high open‐circuit voltage; however, polymer solar cells in which the linear naphtho[2,3‐b;6,7‐d′]dithiophene‐based copolymer is used as the electron donor material perform better than the cells prepared using the zigzag naphtho[1,2‐b:5,6‐b′]dithiophene‐based copolymer. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 305–312     

Synthesis and characterization of biodegradable triblock copolymers based on bacterial poly[(R)‐3‐hydroxybutyrate] by atom transfer radical polymerization

Biodegradable poly(tert‐butyl acrylate)–poly[(R)‐3‐hydroxybutyrate]–poly (tert‐butyl acrylate) triblock copolymers based on bacterial poly[(R)‐3‐hydroxybutyrate] (PHB) were synthesized by atom transfer radical polymerization. The chain architectures of the triblock copolymers were confirmed by ¹H NMR and ¹³C NMR spectra. Gel permeation chromatography analysis was used to estimate the molecular weight characteristics and lengths of the PHB and poly(tert‐butyl acrylate) blocks of the copolymers. The thermal properties of the copolymers were studied by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). TGA showed that the triblock copolymers underwent stepwise thermal degradation and had better thermal stability than their respective homopolymers, whereas DSC analyses showed that a microphase‐separation structure was formed only in the triblock copolymers with the longer PHB block. As a similar result, from wide‐angle X‐ray diffraction experimentation, the crystalline phase of PHB could not be seen evidently in the triblock copolymers with the shorter PHB block. The enzymatic hydrolysis of the copolymer films was carried at 37 °C and pH 7.4 in a potassium phosphate buffer with an extracellular PHB depolymerase from Penicillum sp. The biodegradability of the triblock copolymers increased with an increase in the PHB block content. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4857–4869, 2005     

Doubly thermoresponsive brush‐linear‐linear ABC triblock copolymer nanoparticles prepared through dispersion RAFT polymerization

Doubly thermoresponsive ABC brush‐linear‐linear triblock copolymer nanoparticles of poly[poly(ethylene glycol) methyl ether vinylphenyl]‐block‐poly(N‐isopropylacrylamide)‐block‐polystyrene [P(mPEGV)‐b‐PNIPAM‐b‐PS] containing two thermoresponsive blocks of poly[poly(ethylene glycol) methyl ether vinylphenyl] [P(mPEGV)] and poly(N‐isopropylacrylamide) (PNIPAM) are prepared by macro‐RAFT agent mediated dispersion polymerization. The P(mPEGV)‐b‐PNIPAM‐b‐PS nanoparticles exhibit two separate lower critical solution temperatures or phase‐transition temperatures (PTTs) corresponding to the linear PNIPAM block and the brush P(mPEGV) block in water. Upon temperature increasing above the first and then the second PTT, the hydrodynamic diameter (D_h) of the triblock copolymer nanoparticles undergoes an initial shrinkage at the first PTT and the subsequent shrinkage at the second PTT. The effect of the chain length of the PNIPAM block on the thermoresponsive behavior of the triblock copolymer nanoparticles is investigated. It is found that, the longer chains of the thermoresponsive PNIPAM block, the greater contribution on the transmittance change of the aqueous dispersion of the triblock copolymer nanoparticles. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2266–2278     

A new insight into the mechanism of 1,3‐dienes cationic polymerization. II. Structure of poly(1,3‐pentadiene) synthesized with tBuCl/TiCl4 initiating system

The microstructure of poly(1,3‐pentadiene) synthesized by cationic polymerization of 1,3‐pentadiene with ^tBuCl/TiCl₄ initiating system is analyzed using one‐dimensional‐ and two‐dimensional‐NMR spectroscopy. It is shown that unsaturated part of chain contains only homo and mixed dyads with trans?1,4‐, trans?1,2‐, and cis?1,2‐structures with regular and inverse (head‐to‐head or tail‐to‐tail) enchainment, whereas cis?1,4‐ and 3,4‐units are totally absent. The new quantitative method for the calculation of content of different structural units in poly(1,3‐pentadiene)s based on the comparison of methyl region of ¹³C NMR spectra of original and hydrogenated polymer is proposed. The signals of tert‐butyl head and chloromethyl end groups are identified in a structure of poly(1,3‐pentadiene) chain and the new approaches for the quantitative calculation of number‐average functionality at the α‐ and ω‐end are proposed. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3297–3307     

Monomer-isomerization polymerization. XIII. Monomer-isomerization polymerization of 1,4-cyclohexadiene with Ziegler-Natta catalyst

1,4-Cyclohexadiene underwent monomer-isomerization polymerization to yield poly(1,3-cyclohexadiene) with a Ziegler-Natta catalyst comprising TiCl₄–Al(C₂H₅)₃ catalyst with Al/Ti molar ratios of 0.5–3.0 at 60°C for 96 hr. Good yields of polymer were obtained (49.5% yield at Al/Ti = 3.0; [η] = 0.04 dl/g). The infrared and NMR spectra of the polymer were identical to those of poly-(1,3-cyclohexadiene), confirming that 1,4-cyclohexadiene first isomerizes to 1,3-cyclohexadiene and then homopolymerizes to give poly-1,3-cyclohexadiene. 1,3-Cyclohexadiene polymerized without isomerization easily in the presence of TiCl₃–Al(C₂H₅)₃ catalyst at Al/Ti molar ratios of 0.5–3.0 at 60°C for 3 hr (76.3% yield at Al/Ti = 3.0; [η] = 0.06 dl/g).     

Thermoresponsive diblock copolymer micellar macro‐RAFT agent‐mediated dispersion RAFT polymerization and synthesis of temperature‐sensitive ABC triblock copolymer nanoparticles

The micellar macro‐RAFT agent‐mediated dispersion polymerization of styrene in the methanol/water mixture is performed and synthesis of temperature‐sensitive ABC triblock copolymer nanoparticles is investigated. The thermoresponsive diblock copolymer of poly(N,N‐dimethylacrylamide)‐block‐poly[N‐(4‐vinylbenzyl)‐N,N‐diethylamine] trithiocarbonate forms micelles in the polymerization solvent at the polymerization temperature and, therefore, the dispersion RAFT polymerization undergoes as similarly as seeded dispersion polymerization with accelerated polymerization rate. With the progress of the RAFT polymerization, the molecular weight of the synthesized triblock copolymer of poly(N,N‐dimethylacrylamide)‐block‐poly[N‐(4‐vinylbenzyl)‐N,N‐diethylamine]‐b‐polystyrene linearly increases with the monomer conversion, and the PDI values of the triblock copolymers are below 1.2. The dispersion RAFT polymerization affords the in situ synthesis of the triblock copolymer nanoparticles, and the mean diameter of the triblock copolymer nanoparticles increases with the polymerization degree of the polystyrene block. The triblock copolymer nanoparticles contain a central thermoresponsive poly [N‐(4‐vinylbenzyl)‐N,N‐diethylamine] block, and the soluble‐to‐insoluble ‐‐transition temperature is dependent on the methanol content in the methanol/water mixture. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2155–2165     

Synthesis and characterization of side‐chain liquid crystalline ABC triblock copolymers with p‐methoxyazobenzene moieties by atom transfer radical polymerization

A series of novel side‐chain liquid crystalline ABC triblock copolymers composed of poly(ethylene oxide) (PEO), polystyrene (PS), and poly[6‐(4‐methoxy‐4′‐oxy‐azobenzene) hexyl methacrylate] (PMMAZO) were synthesized by atom transfer radical polymerization (ATRP) using CuBr/1,1,4,7,7‐pentamethyldiethylenetriamine (PMDETA) as a catalyst system. First, the bromine‐terminated diblock copolymer poly(ethylene oxide)‐block‐polystyrene (PEO‐PS‐Br) was prepared by the ATRP of styrene initiated with the macro‐initiator PEO‐Br, which was obtained from the esterification of PEO and 2‐bromo‐2‐methylpropionyl bromide. An azobenzene‐containing block of PMMAZO with different molecular weights was then introduced into the diblock copolymer by a second ATRP to synthesize the novel side‐chain liquid crystalline ABC triblock copolymer poly(ethylene oxide)‐block‐polystyrene‐block‐poly[6‐(4‐methoxy‐4′‐oxy‐azobenzene) hexyl methacrylate] (PEO‐PS‐PMMAZO). These block copolymers were characterized using proton nuclear magnetic resonance (¹H NMR) and gel permeation chromatograph (GPC). Their thermotropic phase behaviors were investigated using differential scanning calorimetry (DSC) and polarized optical microscope (POM). These triblock copolymers exhibited a smectic phase and a nematic phase over a relatively wide temperature range. At the same time, the photoresponsive properties of these triblock copolymers in chloroform solution were preliminarily studied. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4442–4450, 2008     

Diblock copolymers of polystyrene‐b‐poly(1,3‐cyclohexadiene) exhibiting unique three‐phase microdomain morphologies

The synthesis and molecular characterization of a series of conformationally asymmetric polystyrene‐block‐poly(1,3‐cyclohexadiene) (PS‐b‐PCHD) diblock copolymers (PCHD: ～90% 1,4 and ～10% 1,2), by sequential anionic copolymerization high vacuum techniques, is reported. A wide range of volume fractions (0.27 ≤ ?_PS ≤ 0.91) was studied by transmission electron microscopy and small‐angle X‐ray scattering in order to explore in detail the microphase separation behavior of these flexible/semiflexible diblock copolymers. Unusual morphologies, consisting of PCHD core(PCHD‐1,4)–shell(PCHD‐1,2) cylinders in PS matrix and three‐phase (PS, PCHD‐1,4, PCHD‐1,2) four‐layer lamellae, were observed suggesting that the chain stiffness of the PCHD block and the strong dependence of the interaction parameter χ on the PCHD microstructures are important factors for the formation of this unusual microphase separation behavior in PS‐b‐PCHD diblock copolymers. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1564–1572     

Cationic Ring-Opening Polymerization of 1,3-Dehydroadamantanes

Ring-opening polymerizations of [3.3.1]propellane derivatives, 1,3-dehydroadamantane ( 1 ) and 5-butyl-1,3-dehydroadamantane ( 2 ), were carried out with CF₃SO₃H in CH₂Cl₂ at 0 °C for 6–42 h. The central σ-bonds in 1 and 2 were exclusively opened to afford novel poly([3.3.1]propellane)s, poly(1,3-adamantane)s, in 52–95% yields. The resulting poly( 2 ) possessing flexible butyl substituent was soluble in chloroform, THF, and 1,2-dichlorobenzene, and the degree of polymerization was estimated to be greater than 30, while the poly( 1 ) was hardly soluble in the common organic solvents. All aliphatic poly( 1 ) and poly( 2 ) showed high thermal stability, their 10% weight loss temperatures were 421 and 486 °C, respectively.