Studies of photooxidative degradation of poly(vinyl chloride)/poly(ethylene oxide) blends

The photooxidative degradation of blends (in a full range of compositions) of amorphous poly(vinyl chloride) (PVC) with semicrystalline poly(ethylene oxide) (PEO) in the form of thin films is investigated using absorption spectroscopy (UV–visible and Fourier transform infrared) and atomic force microscopy (AFM). The amount of insoluble gel formed as a result of photocrosslinking is estimated gravimetrically. It is found that the PVC/PEO blendsí susceptibility to photooxidative degradation differs from that pure of the components and depends on the blend composition and morphology. Photoreactions such as degradation and oxidation are accelerated whereas dehydrochlorination is retarded in blends. The photocrosslinking efficiency in PVC/PEO blends is higher than in PVC; moreover, PEO is also involved in this process. AFM images showing the lamellar structure of semicrystalline PEO in the blend lead to the conclusion that the presence of PVC does not disturb the crystallization process of PEO. The changes induced by UV irradiation allow the observation of more of the distinct PEO crystallites. This is probably caused by recrystallization of short, more mobile chains in degraded PEO or by partial removal of the less stable amorphous phase from the film surface. These results confirm previous information on the miscibility of PVC with PEO. The mechanism of the interactions between the components and the blend photodegradation are discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 585–602, 2004     

Miscibility and spherulite growth kinetics in the poly(ethylene oxide)/poly(benzyl methacrylate) system

This study for the first time discovered miscibility in the binary blend of semicrystalline poly(ethylene oxide) (PEO) with amorphous poly(benzyl methacrylate) (PBzMA). Differential scanning calorimetry, optical and scanning electron microscopy, and infrared spectroscopy were performed to characterize and demonstrate miscibility in the PEO/PBzMA system. The glass‐transition behavior and Fourier transform infrared results suggest that the intermolecular interactions between the pairs were likely nonspecific and at best comparable to those among the same constituent component. The melting‐point depression study yielded χ = −0.1, indicating a relatively low interaction strength. It is concluded that the phase behavior of the blend was miscibility with nonspecific interactions, mostly a matched polar–polar intermolecular attraction. PEO spherulitic crystallization in the blend is discussed to support the miscibility behavior. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 562–572, 2000     

Recovery as a measure of oriented crystalline structure in poly(ether ester)s based on poly(ethylene oxide) and poly(ethylene terephthalate) used as shape memory polymers

Poly(ether ester)s consisting of poly(ethylene oxide) and poly(ethylene terephthalate) segments, EOET copolymers, could be used as shape memory polymers (SMP). Crystalline structural characters of the copolymers during the memory process were investigated by dynamic mechanical analysis, differential scanning calorimeter, wide-angle X-ray diffraction, polarizing microscopy, and recovery measurements. PEO crystals in stretched EOET copolymer preferentially oriented along fiber axis or stretch direction. During stretching, the structure of the copolymer undertake a transformation from spherulite to fiber, resulting in a crystalline morphology similar to shish-kebab, and recovery properties of stretched EOET samples were dependent on as-described crystalline structural characters that can be influenced by draw ratio. Driving forces for contraction come from the oriented chains, and only oriented or extended chains can be contributive to the recovery of deformation; these extended chains involve both crystalline and amorphous segments. The recovery process in shape memory behavior was noticed to be deorientation of oriented chains due to thermodynamic entropy effect, and was divided into three stages. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 101–112, 1999     

Graft copolymers prepared by ethoxylation of polyamide 12 and poly(ethylene-co-vinyl alcohol)

Graft copolymers consisting of polyamide 12 or poly(ethylene-co-vinyl alcohol) as backbone polymers and side chains of poly(ethylene oxide) have been synthesized. The amide and hydroxyl groups of the backbone polymers were used as initiation sites for the polymerization of ethylene oxide (EO). Potassium tert-butoxide was used for ionization of the active groups, and the polymerization of EO was carried out in dimethyl sulfoxide. The graft copolymers were characterized with respect to molecular weight and composition using elemental analysis, ¹H-NMR, gel permeation chromatography, and FTIR. The size of the side chains varied between 300 and 1000 g/mol. Thermal properties were examined by DSC. The graft copolymers showed increasing crystallinity and increasing melt temperature with increasing molecular weight of the side chains. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 803–811, 1998     

Synthesis and characterization of ABA‐type amphiphilic tri‐block copolymers through anionic polymerization using end functionalized poly(ethylene oxide) oligomers

ABA‐type amphiphilic tri‐block copolymers were successfully synthesized from poly(ethylene oxide) derivatives through anionic polymerization. When poly(styrene) anions were reacted with telechelic bromine‐terminated poly(ethylene oxide) ( 1 ) in 2:1 mole ratio, poly(styrene)‐b‐poly(ethylene oxide)‐b‐poly(styrene) tri‐block copolymers were formed. Similarly, stable telechelic carbanion‐terminated poly(ethylene oxide), prepared from 1,1‐diphenylethylene‐terminated poly (ethylene oxide) ( 2 ) and sec‐BuLi, was also used to polymerize styrene and methyl methacrylate separately, as a result, poly (styrene)‐b‐poly(ethylene oxide)‐b‐poly(styrene) and poly (methyl methacrylate)‐b‐poly(ethylene oxide)‐b‐poly(methyl methacrylate) tri‐block copolymers were formed respectively. All these tri‐block copolymers and poly(ethylene oxide) derivatives, 1 and 2 , were characterized by spectroscopic, calorimetric, and chromatographic techniques. Theoretical molecular weights of the tri‐block copolymers were found to be similar to the experimental molecular weights, and narrow polydispersity index was observed for all the tri‐block copolymers. Differential scanning calorimetric studies confirmed the presence of glass transition temperatures of poly(ethylene oxide), poly(styrene), and poly(methyl methacrylate) blocks in the tri‐block copolymers. Poly(styrene)‐b‐poly(ethylene oxide)‐b‐poly(styrene) tri‐block copolymers, prepared from polystyryl anion and 1 , were successfully used to prepare micelles, and according to the transmission electron microscopy and dynamic light scattering results, the micelles were spherical in shape with mean average diameter of 106 ± 5 nm. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of new amphiphilic diblock copolymers containing poly(ethylene oxide) and poly(α‐olefin)

This article discusses an effective route to prepare amphiphilic diblock copolymers containing a poly(ethylene oxide) block and a polyolefin block that includes semicrystalline thermoplastics, such as polyethylene and syndiotactic polystyrene (s‐PS), and elastomers, such as poly(ethylene‐co‐1‐octene) and poly(ethylene‐co‐styrene) random copolymers. The broad choice of polyolefin blocks provides the amphiphilic copolymers with a wide range of thermal properties from high melting temperature ～270 °C to low glass‐transition temperature ～?60 °C. The chemistry involves two reaction steps, including the preparation of a borane group‐terminated polyolefin by the combination of a metallocene catalyst and a borane chain‐transfer agent as well as the interconversion of a borane terminal group to an anionic (? O^?K⁺) terminal group for the subsequent ring‐opening polymerization of ethylene oxide. The overall reaction process resembles a transformation from the metallocene polymerization of α‐olefins to the ring‐opening polymerization of ethylene oxide. The well‐defined reaction mechanisms in both steps provide the diblock copolymer with controlled molecular structure in terms of composition, molecular weight, moderate molecular weight distribution (M_w/M_n < 2.5), and absence of homopolymer. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3416–3425, 2002     

Surface covalent encapsulation of multiwalled carbon nanotubes with poly(acryloyl chloride) grafted poly(ethylene glycol)

Multiwall carbon nanotube (MWNT) was grafted with polyacrylate‐g‐poly (ethylene glycol) via the following two steps. First, hydroxyl groups on the surface of acid‐treated MWNT reacted with linear poly(acryloyl chloride) to generate graft on MWNT; secondly, the remaining acryloyl chloride groups were subjected to esterification with poly(ethylene glycol) leading the grafted chains on the surface of MWNTs. Thus obtained grafted MWNT was characterized using Fourier transform infrared spectrometer, transmission electron microscopy, and X‐ray photoelectron spectroscopy. Thermogravimetric analysis showed that the weight fraction of grafted polymers amounted to 80% of the modified MWNT. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6880–6887, 2006     

Nucleation and growth of gas barrier aluminium oxide on surfaces of poly(ethylene terephthalate) and polypropylene: effects of the polymer surface properties

The nucleation and initial stages of growth of aluminium oxide deposited on two different polymer surfaces [poly(ethylene terephthalate), (PET) and amorphous polypropylene, (PP)] have been studied by atomic force microscopy (AFM). The permeation of water vapor and oxygen through the films has been measured. The initial stages of the growth of the oxide consisted of separated islands on the polymer surface. Further growth of oxide depends strongly on the surface morphology and chemical nature of the polymer surface. Growth on PET follows a layer‐by‐layer mechanism that maintains the native surface roughness of the polymer substrate. Growth on PP, however, follows an island mode, which leads to an increase in surface roughness. This may be due to a lack of chemical bonding between the polymer and the arriving metal–oxygen particles. The oxide layer on PET grows more densely than on PP, providing superior barrier to gas permeation. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 3151–3162, 2000     

Block copolymers of poly(ethylene oxide) and poly(vinyl alcohol) synthesized by the RAFT methodology

A methodology for the synthesis of well‐defined poly(ethylene oxide)‐block‐poly(vinyl alcohol) (PEO‐b‐PVA) and PVA‐b‐PEO‐b‐PVA polymers was reported. Novel xanthate end‐functionalized PEOs were synthesized by a series of end‐group transformations. They were then used to mediate the reversible addition–fragmentation chain transfer polymerization of vinyl acetate to obtain well‐defined poly(ethylene oxide)‐b‐poly(vinyl acetate) (PEO‐b‐PVAc) and PVAc‐b‐PEO‐b‐PVAc. When these block copolymers were directly hydrolyzed in methanol solution of sodium hydroxide, polymers with brown color were obtained, which was due to the formation of conjugated unsaturated aldehyde structures. To circumvent these side reactions, the xanthate groups were removed by adding a primary amine before hydrolysis and the products thus obtained were white powders. The polymers were characterized by gel permeation chromatography, ¹H NMR spectroscopy and FT‐IR. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1901–1910, 2009     

Complexation of linear and poly(ethylene oxide)‐grafted poly(methacryl oxyethyl trimethylammonium chloride) with poly(ethylene oxide‐block‐sodium methacrylate)

The interactions between oppositely charged polyelectrolytes were studied in saline aqueous solutions as functions of the temperature and the salt and polymer concentrations. The polyanion was a diblock copolymer composed of a poly(ethylene oxide) block and a poly(sodium methacrylate) block. Two polycations were used, the homopolymer poly(methacryl oxyethyl trimethylammonium chloride) and its poly(ethylene oxide)‐grafted analogue. By dynamic light scattering and turbidity measurements, it was observed that the salt concentration, temperature, and counterion size had a significant effect on the formation of the polymer complexes in aqueous solutions. At a fixed salt concentration and a fixed temperature, it was possible to form completely soluble complexes of an ionic polymer in aqueous solutions between poly(ethylene oxide)‐grafted poly(methacryl oxyethyl trimethylammonium chloride)and the polyanion with a poly(ethylene oxide) block at a 1:1 anion/cation ratio. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1904–1914, 2003     

From poly(N‐isopropylacrylamide)‐block‐poly(ethylene oxide)‐block‐poly(N‐isopropylacrylamide) triblock copolymer to poly(N‐isopropylacrylamide)‐block‐poly(ethylene oxide) hydrogels: Synthesis and rapid deswelling and reswelling behavior of hydrogels

Poly(N‐isopropylacrylamide)‐block‐poly(ethylene oxide)‐block‐poly(N‐isopropylacrylamide) (PNIPAAm‐b‐PEO‐b‐PNIPAAm) triblock copolymer was synthesized via the reversible addition‐fragmentation chain transfer/macromolecular design via the interchange of xanthate (RAFT/MADIX) process with xanthate‐terminated poly(ethylene oxide) (PEO) as the macromolecular chain transfer agent. The successful synthesis of the ABA triblock copolymer inspired the preparation of poly(N‐isopropylacrylamide)‐block‐poly(ethylene oxide) (PNIPAAm‐b‐PEO) copolymer networks with N,N′‐methylenebisacrylamide as the crosslinking agent with the similar approach. With the RAFT/MADIX process, PEO chains were successfully blocked into poly(N‐isopropylacrylamide) (PNIPAAm) networks. The unique architecture of PNIPAAm‐b‐PEO networks allows investigating the effect of the blocked PEO chains on the deswelling and reswelling behavior of PNIPAAm hydrogels. It was found that with the inclusion of PEO chains into the PNIPAAm networks as midblocks, the swelling ratios of the hydrogels were significantly enhanced. Furthermore, the PNIPAAm‐b‐PEO hydrogels displayed faster response to the external temperature changes than the control PNIPAAm hydrogel. The accelerated deswelling and reswelling behaviors have been interpreted based on the formation of PEO microdomains in the PNIPAAm networks, which could act as the hydrophilic tunnels to facilitate the diffusion of water molecules in the PNIPAAm networks. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Segmented block copolymers of poly(ethylene glycol) and poly(ethylene terephthalate)

A new series of segmented copolymers were synthesized from poly(ethylene terephthalate) (PET) oligomers and poly(ethylene glycol) (PEG) by a two‐step solution polymerization reaction. PET oligomers were obtained by glycolysis depolymerization. Structural features were defined by infrared and nuclear magnetic resonance (NMR) spectroscopy. The copolymer composition was calculated via ¹H NMR spectroscopy. The content of soft PEG segments was higher than that of hard PET segments. A single glass‐transition temperature was detected for all the synthesized segmented copolymers. This observation was found to be independent of the initial PET‐to‐PEG molar ratio. The molar masses of the copolymers were determined by gel permeation chromatography (GPC). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4448–4457, 2004     

Microwave assisted hydroxyalkylamidation of poly(ethylene‐co‐acrylic acid) and formation of grafted poly(ϵ‐caprolactone) side chains

The microwave assisted amidation of poly(ethylene‐co‐acrylic acid) (PEAA) with 2‐(2‐aminoethoxy)ethanol was performed to yield a hydroxy functionalized poly(ethylene) based copolymer (PEAAOH) in a single step. PEAAOH was used as a polyinitiator for the ring‐opening polymerization of ε‐caprolactone. The obtained graft copolymers were studied via ¹H NMR spectroscopy, gel permeation chromatography, differential scanning calorimetry, polarized optical microscopy, and scanning electron microscopy. Microscopy methods show a crystallization behavior of banded spherulites. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3659–3667, 2007     

Synthesis of branch‐ring‐branch tadpole‐shaped [linear‐poly(ε‐caprolactone)]‐b‐[cyclic‐poly(ethylene oxide)]‐b‐ [linear‐poly(ε‐caprolactone)] by combination of glaser coupling reaction with ring‐opening polymerization

A novel amphiphilic branch‐ring‐branch tadpole‐shaped [linear‐poly(ε‐caprolactone)]‐b‐[cyclic‐poly(ethylene oxide)]‐b‐[linear‐poly(ε‐caprolactone)] [(l‐PCL)‐b‐(c‐PEO)‐b‐(l‐PCL)] was synthesized by combination of glaser coupling reaction with ring‐opening polymerization (ROP) mechanism. The self‐assembling behaviors of (l‐PCL)‐b‐(c‐PEO)‐b‐(l‐PCL) and their π‐shaped analogs of poly(ε‐caprolactone)/poly(ethylene oxide)]‐b‐poly(ethylene oxide)‐b‐[poly(ε‐caprolactone)/poly(ethylene oxide) with comparable molecular weight in water were preliminarily investigated. The results showed that the micelles formed from the former took a fiber look, however, that formed from the latter took a spherical look. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Water‐soluble poly(ethylene oxide)‐block‐poly(p‐phenylene vinylene) copolymer: Synthesis and characterization

Water‐soluble and photoluminescent block copolymers [poly(ethylene oxide)‐block‐poly(p‐phenylene vinylene) (PEO‐b‐PPV)] were synthesized, in two steps, by the addition of α‐halo‐α′‐alkylsulfinyl‐p‐xylene from activated poly(ethylene oxide) (PEO) chains in tetrahydrofuran at 25 °C. This copolymerization, which was derived from the Vanderzande poly(p‐phenylene vinylene) (PPV) synthesis, led to partly converted PEO‐b‐PPV block copolymers mixed with unreacted PEO chains. The yield, length, and composition of these added sequences depended on the experimental conditions, namely, the order of reagent addition, the nature of the monomers, and the addition of an extra base. The addition of lithium tert‐butoxide increased the length of the PPV precursor sequence and reduced spontaneous conversion. The conversion into PPV could be achieved in a second step by a thermal treatment. A spectral analysis of the reactive medium and the composition of the resulting polymers revealed new evidence for an anionic mechanism of the copolymerization process under our experimental conditions. Moreover, the photoluminescence yields were strongly dependant on the conjugation length and on the solvent, with a maximum (70%) in tetrahydrofuran and a minimum (<1%) in water. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4337–4350, 2005     

Electron microscopy of high‐pressure crystallized poly(ethylene terephthalate)

The high‐pressure crystallized poly(ethylene terephthalate) samples were investigated with scanning electron microscopy. The striation appearance, which is the most common feature of polymer extended‐chain crystals, was clearly observed. Poly(ethylene terephthalate) extended‐chain crystals with thickness up to 17 m were obtained at high pressure. Fibrous crystals were also formed at high pressure. The fracture behaviors, which affected the exposure of the striations, were also discussed. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1612–1616, 2000     

Interval kinetic gravimetric sorption of acetone in random copolymers of poly(ethylene terephthalate) and poly(ethylene 2,6-naphthalate)

Interval sorption kinetics of acetone in solvent cast films of random poly(ethylene terephthalate)-co-(ethylene 2,6-naphthalate) (PET-co-PEN) are reported at 35°C and at acetone pressures ranging from 0 to 7.3 cm Hg. Polymer composition is varied systematically from 0% to 50% poly(ethylene 2,6-naphthalate). Equilibrium sorption is well described by the dual-mode sorption model. Interval sorption kinetics are described using a two-stage model that incorporates both Fickian diffusion and protracted polymer structural relaxation. The incorporation of low levels of PEN into PET significantly reduces the excess free volume associated with the glassy state and, for these interval acetone sorption experiments in ∼ 5 μm-thick films, decreases the fraction of acetone uptake controlled by penetrant-induced polymer structural relaxation. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2973–2984, 1999     

AFM study of morphological development during the melt-crystallization of poly(ethylene oxide)

The atomic force microscope (AFM) has been used to investigate morphological development during the crystallization of poly(ethylene oxide) (PEO) from the melt. PEOs with molecular weights of 1 × 10⁵ and 7 × 10⁶ were used. Height and amplitude images were recorded, using the tapping mode. For both polymers, the mode of spherulite development varied with the velocity of the growth front. For slow growth velocities, the growth of the crystallites was linear, with growth initially occurring by single lamellae, later developing into growth arms by screw dislocation spawning of crystallites. At intermediate growth velocities, stacks of lamellae develop rapidly. The splaying apart of adjacent crystals and growth arms is abundant. The operation of growth spirals was observed directly in this growth velocity range. The crystals formed by the giant screw dislocations diverge immediately from the original growth direction, providing a source of interlamellar splaying. At low and intermediate velocities, the front propagates by the advance of primary growth arms, with the regions between the arms filled in by arms growing behind the primary front. At the highest velocity observed here, the formation of lamellar bundles and immediate splaying results in recognizable spherulites developing at the earliest stages of crystallization. The change from linear growth to splaying and nonlinear growth are qualitatively explained in terms of driving force, elastic resistance and the presence of compositional and/or elastic fields in the melt. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. B Polym. Phys. 36: 2311–2325, 1998     

Thermal and mechanical properties of mandelic acid‐copolymerized poly(butylene succinate) and poly(ethylene adipate)

Phenyl side chains were introduced to poly(butylene succinate) and poly(ethylene adipate) by the polymerization of the respective monomers in the presence of mandelic acid. The increasing content of the phenyl side chains decreased the melting temperature and the crystallinity but increased the glass‐transition temperature of the aliphatic polyesters. The phenyl side branches reduced the crystallinity of poly(butylene succinate) more significantly than the ethyl or n‐octyl side branches did. The tensile strength, elongation, and tear strength of poly(ethylene adipate) decreased with an increase in the content of mandelic acid units. However, the increasing content of mandelic acid units enhanced the elongation and tear strength of poly(butylene succinate) considerably without a notable deterioration of tensile strength. The biodegradability of the copolyesters was increased as a result of the introduction of more mandelic acid units due to the decrease in the crystallinity. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1504–1511, 2000     

Compatibilization of blends of polybutadiene and poly(methyl methacrylate) with poly(butadiene-block-methyl methacrylate)

Compatibilization of blends of polybutadiene and poly(methyl methacrylate) with butadiene-methyl methacrylate diblock copolymers has been investigated by transmission electron microscopy. When the diblock copolymers are added to the blends, the size of PB particles decreases and their size distribution gets narrower. In PB/PMMA7.6K blends with P(B-b-MMA)25.2K as a compatibilizer, most of micelles exist in the PMMA phase. However, using P(B-b-MMA)38K as a compatibilizer, the micellar aggregation exists in PB particles besides that existing in the PMMA phase. The core of a micelle in the PMMA phase is about 10 nm. In this article the influences of temperature and homo-PMMA molecular weight on compatibilization were also examined. At a high temperature PB particles in blends tend to agglomerate into bigger particles. When the molecular weight of PMMA is close to that of the corresponding block of the copolymer, the best compatibilization result would be achieved. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36 : 85–93, 1998