Emulsion copolymerization of vinylidene chloride and methyl methacrylate. I. Effects of operating variables on the kinetic behavior

The effects of operating variables on the kinetic behavior of the emulsion copolymerization of vinylidene chloride (VDC) and methyl methacrylate (MMA) were examined at 50 °C with sodium lauryl sulfate as an emulsifier and potassium persulfate as an initiator, respectively. The number of polymer particles produced increased in proportion to the 1.0 power of the initial emulsifier concentration and to the 0.3 power of the initial initiator concentration and decreased with an increasing content of MMA in the initial monomer charge. The rate of copolymerization was proportional to the 0.4 power of the initial emulsifier concentration and to the 0.5 power of the initial initiator concentration and increased with an increasing content of MMA in the initial monomer charge. The molecular weight of copolymer produced decreased drastically with an increasing content of VDC in the initial monomer charge. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1275–1284, 2002     

Kinetics and mechanisms of emulsion polymerization initiated by oil-soluble initiators. IV. Kinetic modeling of unseeded emulsion polymerization of styrene initiated by 2,2′-azobisisobutyronitrile

To explain the kinetic features of particle formation and growth in unseeded emulsion polymerization initiated by oil-soluble initiators, a mathematical kinetic model is proposed, based on the assumption that when initiator radicals or monomer radicals in the water phase enter monomer-solubilized emulsifier micelles, initiate polymerization, and propagate to a chain length which is long enough not to desorb from the micelles, the micelles are regarded to be transformed into polymer particles. It is demonstrated by comparing the experimental results obtained in the emulsion polymerization of styrene initiated by the oil-soluble initiator, 2,2'-azobisisobutyronitrile, with sodium lauryl sulfate as emulsifier that the proposed kinetic model satisfactorily explains the kinetic features such as the effects of initial emulsifier, initiator, and monomer concentrations on both the number of polymer particles produced and the monomer conversion versus time histories. © 1993 John Wiley & Sons, Inc.     

Particle formation under monomer‐starved conditions in the semibatch emulsion polymerization of styrene. I. Experimental

Particle formation and particle growth compete in the course of an emulsion polymerization reaction. Any variation in the rate of particle growth, therefore, will result in an opposite effect on the rate of particle formation. The particle formation in a semibatch emulsion polymerization of styrene under monomer‐starved conditions was studied. The semibatch emulsion polymerization reactions were started by the monomer being fed at a low rate to a reaction vessel containing deionized water, an emulsifier, and an initiator. The number of polymer particles increased with a decreasing monomer feed rate. A much larger number of particles (within 1–2 orders of magnitude) than that generally expected from a conventional batch emulsion polymerization was obtained. The results showed a higher dependence of the number of polymer particles on the emulsifier and initiator concentrations compared with that for a batch emulsion polymerization. The size distribution of the particles was characterized by a positive skewness due to the declining rate of the growth of particles during the nucleation stage. A routine for monomer partitioning among the polymer phase, the aqueous phase, and micelles was developed. The results showed that particle formation most likely occurred under monomer‐starved conditions. A small average radical number was obtained because of the formation of a large number of polymer particles, so the kinetics of the system could be explained by a zero–one system. The particle size distribution of the latexes broadened with time as a result of stochastic broadening associated with zero–one systems. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3940–3952, 2001     

Butyl acrylate batch emulsion polymerization in the presence of sodium lauryl sulphate and potassium persulphate

The batch emulsion polymerization of butyl acrylate in the presence of sodium lauryl sulphate as emulsifier and potassium persulphate as initiator was investigated. The effects of emulsifier concentration, initiator concentration, and monomer/water ratio on the kinetic features were studied. The kinetic data showed that at the conditions studied, the number of particles is proportional to [KPS]^0.39 and [SLS]^0.54. The number of particles did not practically vary with monomer concentration at the high range of monomer and emulsifier concentrations. At low emulsifier concentration, particle coagulation occurred in the course of reaction, which increased with monomer concentration. Particle nucleation was found to occur during Interval III of the batch process if undissociated micelles exist. It was also confirmed that the zero-one kinetics system can better fit the experimental results, compared to the pseudobulk kinetics. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3957–3972, 1999     

Sterically stabilized emulsion polymerization of styrene: Pseudo‐semicontinuous approach

The sterically stabilized emulsion polymerization of styrene initiated by a water‐soluble initiator at different temperatures has been investigated. The rate of polymerization (R_p) versus conversion curve shows the two non‐stationary‐rate intervals typical for the polymerization proceeding under non‐stationary‐state conditions. The shape of the R_p versus conversion curve results from two opposite effects—the increased number of particles and the decreased monomer concentration at reaction loci as the polymerization advances. At elevated temperatures the monomer emulsion equilibrates to a two‐phase or three‐phase system. The upper phase is transparent (monomer), and the lower one is blue colored, typical for microemulsion. After stirring such a multiphase system and initiation of polymerization, the initial coarse polymer emulsion was formed. The average size of monomer/polymer particles strongly decreased up to about 40% conversion and then leveled off. The initial large particles are assumed to be highly monomer‐swollen particles formed by the heteroagglomeration of unstable polymer particles and monomer droplets. The size of the “highly monomer” swollen particles continuously decreases with conversion, and they merge with the growing particles at about 40–50% conversion. The monomer droplets and/or large highly monomer‐swollen polymer particles also serve as a reservoir of monomer and emulsifier. The continuous release of nonionic (hydrophobic) emulsifier from the monomer phase increases the colloidal stability of primary particles and the number of polymer particles, that is, the particle nucleation is shifted to the higher conversion region. Variations of the square and cube of the mean droplet radius with aging time indicate that neither the coalescence nor the Ostwald ripening is the main driving force for the droplet instability. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 804–820, 2003     

Microemulsion polymerization of butyl acrylate. IV. Effect of emulsifier concentration

The oil/water microemulsion polymerizations of butyl acrylate initiated by a water (ammonium peroxodisulfate, APS) or oil (dibenzoyl peroxide, DBP) soluble radical initiator at different emulsifier concentrations were investigated. The rate of polymerization vs. conversion curve shows two intervals. The rate of polymerization is found to decrease with the emulsifier concentration. This finding was discussed in terms of the decrease of both radical and monomer concentration, the chain transfer to emulsifier, desorption of chaintransferred radicals, and the contribution of solution polymerization. The polymerization is faster with APS. In the APS system the rate per particle or the number of radicals per particle increases exponentially with increasing particle size. The particle size and number increase during the whole polymerization. This behavior was discussed in terms of the nucleation of monomer-containing micelles and agglomeration of primary particles during the whole polymerization. © 1995 John Wiley & Sons, Inc.     

Particle formation in interval III of the emulsion polymerization of styrene with aerosol‐MA as an emulsifier

Particle nucleation in the seeded emulsion polymerization of styrene in the presence of Aerosol‐MA emulsifier micelles and in the absence of monomer droplets (interval III) was investigated. The seed particles were swollen with different amounts of the styrene monomer before the experiments. A larger number of polymer particles formed in interval III than in the corresponding seeded batch operation in the presence of monomer droplets. The increase in the number of particles could be attributed to the reduced rate of growth of new particles, which retarded the depletion of emulsifier micelles. The number of secondary particles initially increased with the initial polymer weight ratio in the seed particles (w_p0) but decreased at a higher range of w_p0, after reaching a maximum at w_p0 = 0.60, and eventually was reduced to zero. At high values of w_p0 (>0.75), polymerization occurred in the seed particles, whereas few or no new particles were formed despite the presence of micelles. The cessation of particle formation at high conversions was ascertained with a semibatch process in which the neat monomer feed was added to the reaction vessel containing the seed particles and emulsifier micelles. For w_p0 > 0.85, the emulsifier micelles were disintegrated to stabilize the seed particles with no secondary particle formation. The possible reasons for the cessation of particle formation at high w_p0 were examined. The size distribution of secondary particles showed a positive skewness in terms of volume because of the declining rate of growth for particles, together with a low rate of growth for small particles. The distribution breadth of new particles sharpened with increasing w_p0. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1652–1663, 2002     

On the emulsion polymerization of styrene in the presence of a nonionic emulsifier

The batch emulsion polymerization kinetics of styrene (St) initiated by a water-soluble peroxodisulfate in the presence of a nonionic emulsifier was investigated. The polymerization rate versus the conversion curves showed two nonstationary rate intervals, two rate maxima, and Smith–Ewart Interval 2 (nondistinct). The rate of polymerization and number of nucleated polymer particles were proportional to the 1.4th and 2.4th powers, respectively, of the emulsifier concentration. Deviation from the micellar nucleation model was attributed to the low water solubility of the emulsifier, the low level of the micellar emulsifier, and the mixed modes of particle nucleation. In emulsion polymerizations with a low emulsifier concentration, the number of radicals per particle and particle size increased with increasing conversion, and the increase was more pronounced at a low conversion. By contrast, in emulsion polymerizations with a high emulsifier concentration, the number of radicals per particle decreased with increasing conversion. This is discussed in terms of the mixed models of particle nucleation, the gel effect, and the pseudobulk kinetics. The formation of monodisperse latex particles was attributed to coagulative nucleation and droplet nucleation for the polymerizations with low and high emulsifier concentrations, respectively. The effects of the continuous release of the emulsifier from nonmicellar aggregates and monomer droplets, the close-packing structure of the droplet surface, and the hydrophobic nature of the emulsifier on the emulsion polymerization of St are discussed. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 4422–4431, 1999     

Radical polymerization in homogenized butyl acrylate emulsion

The addition of a small amount of monomer strongly decreased the clouding temperature of nonionic emulsifier (Tween 20). The clouding temperature of the Tween 20 aqueous solution was independent of emulsifier concentration but it strongly varied in the presence of monomer. The decreased cloud temperature was attributed to the penetration of monomer molecules into the interfacial layer that increased the flocculation of microdroplets (monomer-swollen micelles). The surface tension of homogenized ((mini)emulsion) butyl acrylate aqueous emulsion was much smaller than that estimated at or above CMC of Tween 20. The polymerization rate vs. conversion curve of the (mini)emulsion deviates from the three rate intervals typical for the emulsion polymerisation. The shape of the rate-conversion curve reminds more the four rate intervals curve. Interval 2 is overlapped with the initial maximal rate and rate shoulder at higher conversion. The initial maximal polymerization rate (R_p,max,1) is attributed to the abrupt increase in polymer particles, the polymerization under monomer saturated condition and emulsifier containing peroxide groups (Tw_peroxid 20). The rate of emulsion polymerization of BA initiated by ammonium peroxodisulphate (APS) is ca. by one order of magnitude larger than that of blank polymerization (without APS). The second maximal rate (rate shoulder) can result from the gel effect. The more pronounced increase in R_p,max,1 with Tw 20 concentration supports the presence of peroxide groups. The slight dependence of R_p,max,2 on [Tw 20] for both APS and DBP (dibenzoyl peroxide) is discussed in terms of the depressed radical entry rate into the close packed surface later of polymer particles. The low activation energy is attributed to the decreased barrier for entering radicals into the polymer particles with increasing temperature. This is more pronounced with the accumulation of covalently bound emulsifier moieties (resulting from Tw_peroxid 20) at the particle surface. The ratio of the final number of polymer particles to the initial number of monomer droplets (N_p/N_drop) promotes the partial monomer droplet nucleation. The dye approach indicates that the degree of depletion of monomer droplets decreases from the classical emulsion polymerization to the polymerization in pre-homogenized emulsions and the emulsion polymerization with a prolonged-emulsification interval.     

Radiation-induced emulsion polymerization of ethylene. VI. Continuous flow system

The radiation-induced emulsion polymerization of ethylene in a continuous flow system was carried out at 100°C by using FC-143 and potassium myristate. The polymer concentration in the latex during the course of the polymerization oscillated several times and then approached a steady-state value in a few hours in the case of short residence time. The rate of polymerization was almost constant within the residence time range of 0.2–0.9 hr. This is explained by the kinetics assuming the same mechanism previously proposed in the batch system, that is, the number of polymer particles in this range is considered to be constant. Gel formation was observed at longer reaction times in spite of the continuous supply of myristate micelles, possibly because large polymer particles are produced in this stage. The concentration of carbonyl group in the polymer produced by chain transfer to absorbed myristate ion changes in the same way as the polymer concentration with reaction time. The methyl group in the polymer is produced mainly by chain transfer to the polymer, and the concentration is nearly constant during the polymerization except in the initial stage. The rate constants for the continuous polymerization were very different from the batch polymerization previously studied, despite their similarities in nature. The mass transfer rate of the emulsifier from the micelles to the polymer particles requires future study.     

Kinetics of the photoinitiated inverse microemulsion polymerization of 2-methacryloyl oxyethyl trimethyl ammonium chloride

The polymerization of inverse microemulsions of 2-methacryloyl oxyethyl trimethyl ammonium chloride stabilized by a blend of nonionic emulsifiers (a sorbitan sesquioleate and a sorbitan monooleate) and initiated by UV light in the presence of Azobis(isobutyronitrile) (AIBN) was investigated. The effect of initiator concentration, light intensity, emulsifier concentration, and dispersed phase weight fraction on the polymerization rate (R_p), number of polymer particles (N_p), and polymer molecular weight (M_w) was studied. The application of this process to tubular reactors is discussed. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 737–748, 1998     

Emulsion polymerization of styrene using an alkali-soluble random copolymer as polymeric emulsifier

An alkali-soluble random copolymer (ASR), poly(styrene/α-methylstyrene/acrylic acid), was used as a polymeric emulsifier in the emulsion polymerization of styrene. The calorimetric technique was applied to study the kinetics of emulsion polymerization of styrene using ASR and a conventional ionic emulsifier, sodium dodecyl benzenesulfonate (SDBS). ASR could form aggregates like micelles, and the solubilization ability of the aggregates was dependent on the neutralization degree of ASR. The rate of polymerization in the ASR system was lower than that in the SDBS system. This result can be explained by the creation of a hairy ASR layer around the particle surface, which decreases the diffusion rate of free radicals through this region. Although a decrease in particle size was observed, the rate of polymerization decreased with increasing ASR concentration. The higher the concentration of ASR is, the thicker and denser ASR layer may be, and the more difficult it would therefore be for radicals to reach the particle through this layer of ASR. The rate of polymerization decreased with increasing the neutralization degree of ASR. The aggregates with high neutralization of ASR are less efficient in solubilizing the monomer and capturing initiator radicals than that of the lower neutralization degree, which leads to decrease in rate of polymerization. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 2865–2872, 1998     

Seeded microemulsion polymerization of butyl acrylate

The seeded microemulsion polymerization of butyl acrylate was studied with γ-rays. The hydrodynamic diameter and its distribution of polymer particles in the seeded microemulsion before and after polymerization were determined with photon correlation spectroscopy (PCS). Though there were micelles in the microemulsion, it was found that new particle formation could be ignored during polymerization. The polymerization kinetics of the seeded microemulsion was investigated. The polymerization rate increases with the dose rate and added monomer content and decreases with the seed fraction. It was completely different from that for seeded emulsion polymerization. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A Polym. Chem. 36: 2631–2635, 1998     

Radiation-induced emulsion polymerization of ethylene. II. Effect of potassium myristate concentration and dose rate on the rate of polymerization in connection with polymer properties,kinetics, and mechanism

Radiation-induced emulsion polymerization of ethylene with potassium myristate as an emulsifier was studied in connection with the kinetics and the mechanism. The molecular weight of polymer was relatively low, of the order of 10³, when a sufficient amount of emulsifier was used. However, polyethylene gel was produced in the absence of a sufficient amount of emulsifier. The rate of polymerization was proportional to the 0.5 power of dose rate and increased slightly with increasing emulsifier concentration. The rate of seeded polymerization followed a similar trend to that for conventional polymerization. Kinetic analysis of these results suggests that the escape of radicals produced by chain transfer of propagating radical with the emulsifier and the monomer from polymer particles into the aqueous phase plays an important part in the rate of polymerization. The melting temperature and the crystallinity of the polymer significantly decreased with increasing polymerization temperature in the range 40–60°C.     

Particle formation and coagulation in the seeded semibatch emulsion polymerization of butyl acrylate

Particle formation and coagulation in the seeded semibatch emulsion polymerization of butyl acrylate were studied under monomer‐starved conditions. To investigate the importance of the kinetics of the water phase in the nucleation process, the monomer feed rate was used as a variable to alter the monomer concentration in the aqueous phase. The emulsifier concentration in the feed was employed to alter the particle stability. Particle formation and coagulation were discussed in terms of critical surface coverage ratios. Particle coagulation occurred if the particle surface coverage dropped below θ_cr1 = 0.25 ± 0.05. The secondary nucleation occurred above a critical surface coverage of θ_cr2 = 0.55 ± 0.05. The number of particles remained approximately constant if the particle surface coverage was within θ_cr1 = 0.25 < θ < θ_cr2 = 0.55. This surface coverage band is equivalent to the surface tension band of 42.50 ± 5.0 dyne/cm that is required to avoid particle formation and coagulation in the course of polymerization. The kinetics of the water phase was shown to play an important role during homogeneous and micellar nucleations. For any fixed emulsifier concentration in the feed and above θ_cr2, the number of secondary particles increased with monomer concentration in the aqueous phase. Moreover, the presence of micelles in the reaction vessel is not the only perquisite for micellar nucleation to occur, a sufficient amount of monomer should be present in the aqueous phase to enhance the radical capture by partially monomer‐swollen micelles. The rate of polymerization increased with the surfactant concentration in the aqueous phase. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3612–3630, 2000     

Modeling inverse microemulsion polymerization

A mathematical model for inverse microemulsion polymerization has been developed. The model has been used to fit experimental results of the effect of initiator concentration, light intensity, emulsifier concentration, and dispersed phase weight fraction on the monomer conversion evolution, particle size, and polymer molecular weight in the inverse microemulsion polymerization of 2-methacryloyl oxyethyl trimethyl ammonium chloride (MADQUAT) initiated by UV light in the presence of AIBN. A good fitting of the experimental data was achieved. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2167–2178, 1999     

Effect of monomer water solubility on cationic microemulsion polymerization of three components (water,surfactant, and monomer)

Here, we present the oil/water (O/W) microemulsion polymerization in three‐component microemulsions of n‐butyl acrylate, ethyl acrylate, and methyl acrylate, monomers with similar chemical structures but different water solubilities using the cationic surfactant dodecyl trimethyl ammonium bromide. The effects of monomer water solubility, initiator type and initial monomer concentration on the polymerization kinetics were studied. Reaction rates were high with final conversions between 70 and 98% depending on the monomer and reaction conditions. The final latexes were bluish, with a particle size ranging between 20 and 50 nm and polymer with molar masses in the order of 10⁶ g mol^?1. Increasing monomer water solubility resulted in a slower reaction rate, larger particles and a lower number density of particles. A higher reaction rate, larger average particle size and higher particle number density were obtained by increasing the monomer concentration. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Details of the emulsion polymerization of styrene using a reaction calorimeter

An automated reaction calorimeter was used to directly monitor the rate of emulsion polymerization of styrene using different emulsifier (sodium lauryl sulfate) and initiator (potassium persulfate) concentrations. By using this technique in conjunction with off-line measurements of the evolution of the particle size distributions, important details of the process were observed. The classical constant rate period (Interval II) often reported for the batch emulsion polymerization of styrene was not seen in this work. Instead, the experimental results suggest that the end of nucleation and the disappearance of monomer droplets take place at approximately the same conversion (36–40%). From the polymerization rate data, important parameters such as the monomer concentration in the polymer particles and the average number of radicals per particle were calculated. © 1996 John Wiley & Sons, Inc.     

Microemulsion polymerization of styrene in the presence of a cationic emulsifier

The principal subject discussed in the current paper is the radical polymerization of styrene in the three- and four component microemulsions stabilized by a cationic emulsifier. Polymerization in the o/w microemulsion is a new polymerization technique which allows to prepare the polymer latexes with the very high particle interface area and narrow particle size distribution. Polymers formed are very large with a very broad molecular weight distribution. In emulsion and microemulsion polymerizations, the reaction takes place in a large number of isolated loci dispersed in the continuous aqueous phase. However, in spite of the similarities between emulsion and microemulsion polymerization, there are large differences caused by the much larger amount of emulsifier in the latter process. In the emulsion polymerization there are three rate intervals. In the microemulsion polymerization only two reaction rate intervals are commonly detected: first, the polymerization rate increases rapidly with the reaction time and then decreases steadily. Essential features of microemulsion polymerization are as follows: (1) polymerization proceeds under non-stationary state conditions; (2) size and particle concentration increases throughout the course of polymerization; (3) chain-transfer to monomer/exit of transferred monomeric radical/radical re-entry events are operative; and (4) molecular weight is independent of conversion and distribution of resulting polymer is very broad. The number of microdroplets or monomer-starved micelles at higher conversion is high and they persist throughout the reaction. The high emulsifier/water ratio ensures that the emulsifier is undissociated and can penetrate into the microdroplets. The presence of a large amount of emulsifier strongly influences the reaction kinetics and the particle nucleation. The mixed mode particle nucleation is assumed to govern the polymerization process. At low emulsifier concentration the micellar nucleation is dominant while at a high emulsifier concentration the interaction-like homogeneous nucleation is operative. Furthermore, the paper is focused on the initiation and nucleation mechanisms, location of initiation locus, and growth and deactivation of latex particles. Furthermore, the relationship between kinetic and molecular weight parameters of the microemulsion polymerization process and colloidal (water/particle interface) parameters is discussed. In particular, we follow the effect of initiator and emulsifier type and concentration on the polymerization process. Besides, the effects of monomer concentration and additives are also evaluated.