Styrene-assisted melt free radical grafting of glycidyl methacrylate onto polypropylene

The free radical grafting reactivity of glycidyl methacrylate (GMA) onto polypropylene (PP) in the molten state is low. This article shows that adding styrene as a second monomer (or comonomer) increases both the rate and yield of GMA grafting and reduces PP chain scission. The proposed mechanism is that when St is added to the PP/GMA/peroxide grafting system, St reacts first with PP macroradicals to form stable styryl macroradicals. These latter then react (or copolymerize) with GMA to form GMA grafted PP. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1053–1063, 1998     

Synthesis of polyethylene‐grafted multiwalled carbon nanotubes via a peroxide‐initiating radical coupling reaction and by using well‐defined TEMPO and thiol end‐functionalized polyethylenes

Polyethylene (PE), alkoxyamine‐ and thiol‐terminated PEs (PE‐TEMPO and PE‐SH, respectively) can be converted to macroradicals using a peroxide, a thermal cleavage of the alkoxyamine and a hydrogen transfer reaction of the thiol, respectively. The addition of these macroradicals to multiwalled carbon nanotubes (MWCNTs) were compared by performing grafting reactions at 160 °C in 1,3‐dichlorobenzene as solvent. Raman spectroscopy was utilized to follow the introduction of PE on the MWCNTs' surface while thermogravimetric and elemental analysis indicated the extent of this grafting. The grafting ratio was found to be in the range of 19–36 wt %. PE‐functionalized MWCNTs were imaged by transmission electronic microscopy showing a PE layer with various thicknesses covering the surface of nanotubes. It was found that higher levels of grafting were obtained using PE‐2,2,6,6‐tetramethylpiperidinyl‐1‐oxy and PE‐SH rather than a radical grafting reaction in which dicumyl peroxide, PE, and MWCNTs were reacted. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

甲基丙烯酸缩水甘油酯/苯乙烯固相接枝聚丙烯

以苯乙烯(St)为共单体，过氧化苯甲酰(BPO)为引发剂，采用固相接枝反应将甲基丙烯酸缩水甘油酯(GMA)接枝到聚丙烯(PP)大分子链上。研究了反应时间、单体用量、引发剂用量等因素对接枝率的影响。采用凝胶渗透色谱(GPE)测定了PP和接枝物PP-g-(GMA-St)的分子量和分子量分布。结果 表明固相接枝PP反应条件为[GMA／[St]=2，反应3．5h，加入GMA 10份，BPO 5份。St的加入有助于GMA与PP的接枝，同时在一定程度上抑制了PP的降解。     

Grafting of functional nitroxyl free radicals to polyolefins as a tool to postreactor modification of polyethylene‐based materials with control of macromolecular architecture

Nitroxyl radicals were used as functionalizing agents during the free radical postreactor modification process of polyolefins carried out in the melt. The 4‐hydroxy‐2,2,6,6‐tetramethylpiperidine‐1‐oxyl (HO‐TEMPO) and the 4‐benzoyloxy‐2,2,6,6‐tetramethylpiperidine‐1‐oxyl (BzO‐TEMPO) free radicals were successfully grafted onto a polyethylene‐based material (ethylene‐co‐1‐octene copolymer) by coupling reaction with polymer macroradicals; these last were formed by H‐abstraction through peroxide addition. The macromolecular structure of the functionalized polyolefins was assessed by ¹H‐NMR, FTIR spectroscopy, and SEC measurements which were used to evidence the grafting site, to evaluate the grafting level and to highlight the occurrence of chain extension through crosslinking side reactions. Indeed the use of proper model compounds allowed the preparation of accurate FTIR calibration curves for the quantitative determination of the functionalization degree. Besides the high temperature SEC analysis highlighted that this fast and simple coupling reaction between macroradicals and nitroxyl free radicals grants the grafting of functionalities onto the polyolefin backbone by contemporarily preventing the side reactions liable of the structure and MW modification of the pristine polymer. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Free radical polymerization of glycidyl methacrylate in plasticized Poly(vinyl chloride)

Kinetic of free radical in-situ polymerization of glycidyl methacrylate (GMA), was studied in a complex evolutionary system: poly(vinyl chloride) (PVC) plastisols. A predictive model of conversion-time profile based on free radical mechanism was proposed and structure of the modified PVC system developed was investigated by NMR analyses. In order to elucidate the mechanism of the reaction, model molecules for PVC were used with NMR and MALDI-TOF characterization. It was found that in-situ polymerization of GMA in PVC plastisols leads to both homopolymerization and grafting of GMA onto PVC backbone by hydrogen abstraction. For 33 wt% GMA loaded, grafting efficiency is 67% with an amount of grafted poly-glycidyl methacrylate (pGMA) equals to 22 wt%. Thus, this article discloses a new type of PVC plastisols called reactive plastisols where, in addition to usual plasticizers, PVC is modified by polymerizable GMA monomer.     

Synthesis of di‐ and tetra‐adducts by addition of polystyrene macroradicals onto fullerene C60

Br‐terminated polystyrenes of controlled molar masses and low polydispersities prepared by atom transfer radical polymerization (ATRP) can be converted to macroradicals using an appropriate catalytic complex (CuBr/bipyridine/100 °C). The addition of this macroradicals PS° to 6–6 bonds of C₆₀ follows a specific atom transfer radical addition mechanism that favors the grafting of even number of chains onto the fullerene core. This peculiar mechanism, resulting from the properties of C₆₀, offers an easy synthetic route toward well‐defined di‐ and tetra‐adducts. In these adducts the disturbance of the electronic structure of the fullerene is kept at its minimum, as only one double bond needs to be opened on the C₆₀ to add two PS chains and only two double bonds are converted to single bonds in the tetra‐adduct. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3456–3463, 2004     

GMA和共单体对聚乙烯木塑复合材料的直接反应增容

通过甲基丙烯酸缩水甘油酯(GMA)、聚乙烯(PE)、木粉和其它助剂的熔融挤出,实现了GMA及GMA与共单体对PE和木粉的直接反应增容.通过扫描电镜(SEM)观测了PE基木塑复合材料(WPC)的冲击断面形貌.测试了WPC经抽提后所得木粉的傅立叶变换红外光谱(FTIR)和WPC的力学性能及热变形温度(HDT).研究了共单体苯乙烯(St)和抑交联剂亚磷酸三苯酯(TPP)对反应增容的影响.结果显示,经GMA和引发剂反应增容后,有部分PE分子键合到了木粉粒子上,从而增强了木塑两相的结合力;St的加入有利于提高GMA的接枝率,导致更多PE分子键合到了木粉粒子上,而TPP的加入则使GMA的接枝率有所下降.经GMA和引发剂直接反应增容后,WPC的力学性能和HDT均明显改善;St的加入有助于抑制PE的交联,但并未造成WPC力学性能和HDT的明显劣化;同时加入St和TPP后,WPC的HDT有所下降,而断裂伸长率和冲击强度则明显提高.     

马来酸酐-苯乙烯多组分单体熔融接枝高密度聚乙烯机理及性能研究

用单螺杆挤出机制备了马来酸酐-苯乙烯(MAH-St)多单体熔融接枝高密度聚乙烯(HDPE)体系,研究发现添加St共同接枝,可以显著提高接枝物的接枝率.随着St的增加,接枝率先增大后有所降低.当两种单体物质的量比约为1:1时,接枝物的接枝率最高,此时接枝物的熔体流动速率(MFR)最小.即MAH接枝率越高,接枝物的MFR越...     

Reactive compatibilization of polyolefin/PET blends by melt grafting with glycidyl methacrylate

The melt free radical grafting of glycidyl methacrylate (GMA) onto high‐density polyethylene (HDPE) was carried out in Brabender internal mixer. The GMA content of the grafted HDPE (HDPE‐g‐GMA) was determined through FTIR by means of a calibration curve. The influence of reaction procedure, radical initiator concentration and addition of a co‐monomer (styrene) on the grafting efficiency was examined. Blends of poly(ethylene terephthalate) (PET) with HDPE and HDPE‐g‐GMA (75/25 w/w) were prepared by melt mixing in internal mixer. The morphology of the blends was then analysed by SEM microscopy. PET/HDPE‐g‐GMA blends displayed improved phase dispersion and interfacial adhesion as compared to unfanctionalized PET/HDPE blend.     

Ultraviolet grafting of methacrylic acid and acrylic acid on high‐density polyethylene in different solvents and the wettability of grafted high‐density polyethylene. I. Grafting

Methacrylic acid (MAA) and acrylic acid (AA) were grafted onto high‐density polyethylene (PE) with UV initiation and a range of solvents. With acetone as the solvent, MAA was more easily grafted onto PE when the photoinitiator benzophenone was precoated on PE than when it was dissolved in the monomer solution. The grafting was faster in aliphatic solvents than in polar solvents or a UV‐adsorbing aromatic solvent (toluene). Acetone itself could initiate the photografting of both MAA and AA onto PE when it was mixed with water. The extent of grafting of MAA onto PE showed a maximum when there was about 40% acetone in the mixture. For AA, when the acetone/water concentration was 10%, the extent of grafting increased rapidly with the irradiation time. At higher acetone concentrations, the extent of grafting was low. Atomic force microscopy images showed that the surface topography of PE grafted with MAA in acetone/water was quite different from that obtained when the grafting was performed in other organic solvents. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 253–262, 2004     

聚乙烯表面接枝聚合改性及抗凝血性的研究

聚乙烯(PE)膜经Ar等离子体预处理,无光引发剂紫外光照接枝甲基丙烯酸缩水甘油酯(GMA),然后进行肝素化处理,以改善PE的抗凝血性能。用正交实验确定接枝反应的最优条件。通过X-射线光电子能谱(XPS)、衰减全反射红外光谱(ATR-FTIR)、扫描电子显微镜(SEM)和接触角测定PE膜接枝GMA前后表面性能和表面形貌。用复钙时间、凝血酶原时间、部分凝血活酶时间、凝血酶时间和血小板粘附实验对其抗凝血性能进行评价,结果表明,被修饰PE膜的抗凝血性能显著提高。     

Plasma modification of polypropylene surfaces and grafting copolymerization of styrene onto polypropylene

The surface of polypropylene(iPP) is modified with glow discharge plasma of Ar,so that the modified surfaces of iPP films are obtained.The studies of scanning electron microscopy(SEM) show the surface etching pattern of iPP films. The chemical structures of iPP films are confirmed by X-ray photoelectron spectroscopy(XPS) and Fourier transform infrared(FTIR) spectroscopy.The wetting properties of modified surfaces of iPP films are characterized by contact angle, and the free energy of surfaces is calculated.The free radical of modification surfaces of iPP is measured by chemical method.The surfaces of iPP are achieved with Ar plasma treatment followed by grafting copolymerization with styrene(St) in St.The grafting polymer of St onto iPP is characterized by FTIR.The grafting rate is dependent on plasma exposure time and discharge voltage.The studies show that homopolymerization of St is undergone at the same time during the grafting-copolymerization of St onto iPP.     

Polymer grafting onto carbon black by use of TEMPO-terminated polystyrene with controlled molecular weight

The grafting of polystyrene with controlled molecular weight and narrow molecular weight distribution onto the carbon black surface through the trapping of polymer radicals formed by the thermal dissociation of 2,2,6,6-tetramethyl-1-piperidinyloxy (TEMPO)-terminated polystyrene (PSt-TEMPO) by the carbon black surface was investigated. PSt-TEMPO was prepared by living radical polymerization of St with the benzoyl peroxide/TEMPO system. When PSt having no terminal TEMPO moiety was heated with carbon black, no grafting of PSt onto the surface was observed. On the contrary, by the heating of PSt-TEMPO with carbon black in m-xylene at 125°C, PSt with controlled molecular weight and narrow molecular weight distribution was grafted onto the surface: the percentage grafting of PSt (M_n = 3.2 × 10³;M_w/M_n = 1.07) onto furnace black was determined to be 16.0%. On the basis of the above results, it is concluded that PSt radicals formed by the thermal dissociation of the C ON bond between PSt and TEMPO are trapped by polycondensed aromatic rings of carbon black. The mole number of grafted PSt chains on the carbon black surface decreased with increasing molecular weight of PSt-TEMPO. PSt-grafted carbon black gave a stable colloidal dispersion in THF. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 3165–3172, 1998     

Grafting and Degradation Reactions at the Synthesis of Interpenetrating Polymer Networks in Situ from Polyethylene and Butyl Methacrylate

Abstract

The grafting and degradation reactions accompanying the synthesis of interpenetrating polymer networks (IPN) in situ consisting of polyethylene (PE) and poly(butyl methacrylate) (PBMA) were investigated under model conditions. After polymerization at 110°C it was found that the 2,5-dimethyl-2,5-di-(t-butylperoxy)hexane (Luperox-101) had a destructive effect on the PBMA network formed provided the temperature was raised to 160°C. Simultaneously in this reaction stage, further linkage of the PBMA chains with PE originates from a recombination of macroradicals from both polymers. In the thermally initiated polymerization of BMA (in the absence of peroxide), PE is grafted with BMA but no crosslinking of PE takes place. If a mixture of initiators (2,2′ - azo-bis-isobutyronitrile and Luperox-101) was used, a retardation of PE grafting with BMA was observed. A considerable degree of PE crosslinking and grafting of PBMA onto a PE network was achieved if both polymers were mixed with 3 mass % of Luperox-101.     

Elucidation of dominant effect on initial bacterial adhesion onto polymer surfaces prepared by radiation-induced graft polymerization

Surface-modified polyethylene (PE) membrane sheets were prepared by the radiation-induced graft polymerization (RIGP) of an epoxy-group-containing monomer, glycidyl methacrylate (GMA). The epoxy ring of GMA was opened by introducing diethylamine (DEA) or sodium sulfite (SS). We examined the properties of these sheets by measuring the amount of grafting polymer, surface roughness and membrane potential, and also investigated the adhesion of five Gram-negative bacteria, Escherichia coli, Pseudomonas aeruginosa, Pseudomonas putida, Pseudomonas fluorescens and Paracoccus denitrificans, onto the prepared sheet surfaces. A linear relationship between the degree of grafting (dg) and surface roughness was observed. Moreover, membrane potential was dependent on the amount of DEA or SS as the ionizable group. These results indicate that RIGP enables the control of the physicochemical properties of such a sheet surface by adjusting dg and the subsequent conversion of functional groups. A batch test on bacterial adhesion onto the sheets clarified that the DEA-containing sheet (DEA sheet) exhibited an adhesion rate constant, k, significantly greater than those of other types of sheet. Clearly, the adhesion rate constant of the DEA sheet increased with dg, indicating that electrostatic interaction is the most decisive factor for bacterial adhesion when it works as an attractive force. Furthermore, the densities of bacteria adhering onto the GMA-containing sheet (GMA sheet) and the SS-containing sheet (SS sheet) were almost the same as that onto a PE sheet, whereas that onto a DEA sheet significantly increased. Thus, the introduction of the GMA- and SS-containing graft chain did not have much influence on bacterial adhesion onto the surfaces, supporting the conclusion that the promotion of bacterial adhesion onto the GMA and SS sheets was due to an increase in surface area resulting from RIGP. Moreover, the scanning electron microscopy images of the sheet surfaces indicate that the conditions and morphologies of initial bacterial adhesion are dependent on surface properties, particularly membrane potential.     

Solid-state radical grafting reaction of glycidyl methacrylate and poly(4-methyl-1-pentene) in supercritical carbon dioxide: surface morphology and adhesion

Solid-state radical grafting of glycidyl methacrylate (GMA) onto poly(4-methyl-1-pentene) (PMP) was performed using supercritical carbon dioxide (scCO(2)) impregnation technology. The polymer films were firstly impregnated in the scCO(2) phase with the GMA using benzoyl peroxide as thermal initiator. The grafting degree and surface morphology of the samples may be controlled by the following factors: time, temperature, and pressure of impregnation. A 2(3) factorial design to evaluate the main and interaction effects of such factors on the grafting of the PMP by GMA (grafting response) was elaborated from FTIR data. The superior and inferior limits of the levels were defined on basis of a P-x-y diagram for binary system CO(2)+GMA that provided the location of the transition curves of such a system. Better grafting response was obtained for pressure of 130 bar, temperature of 70°C and time of 7h. The PMP-g-GMA films exhibited a thermal profile similar to that of the unmodified polymer. Adhesion characteristics of polymer films are dependent on grafting degree of GMA.     

Chemical modification of poly(lactic acid) induced by thermal decomposition of N‐acetoxy‐phthalimide during extrusion

Chemical modification of poly(lactic acid) (PLA) with N‐acetoxy‐phthalimide (NAPI) was performed in the melt by reactive extrusion, without using any peroxide initiator. The aminyl and nitroxide radicals produced from the NAPI thermal degradation, were, respectively, used (a) to create PLA macroradicals, and (b) to functionalize the PLA samples through nitroxide radical coupling. Depending on the extrusion temperature and the initial NAPI concentration, grafting rates up to 0.24 mol % were measured, modifying the PLA optical properties. This study represents an original new way of modification of PLA without the use of conventional peroxide initiators. Indeed, the undesirable side reactions (PLA branching or crosslinking) usually observed when using peroxides to initiate the radical grafting of PLA were avoided when using NAPI. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 120–129     

Reversible addition–fragmentation chain‐transfer graft polymerization of styrene: Solid phases for organic and peptide synthesis

The γ‐initiated reversible addition–fragmentation chain‐transfer (RAFT)‐agent‐mediated free‐radical graft polymerization of styrene onto a polypropylene solid phase has been performed with cumyl phenyldithioacetate (CPDA). The initial CPDA concentrations range between 1 × 10^?2 and 2 × 10^?3 mol L^?1 with dose rates of 0.18, 0.08, 0.07, 0.05, and 0.03 kGy h^?1. The RAFT graft polymerization is compared with the conventional free‐radical graft polymerization of styrene onto polypropylene. Both processes show two distinct regimes of grafting: (1) the grafting layer regime, in which the surface is not yet totally covered with polymer chains, and (2) a regime in which a second polymer layer is formed. Here, we hypothesize that the surface is totally covered with polymer chains and that new polymer chains are started by polystyrene radicals from already grafted chains. The grafting ratio of the RAFT‐agent‐mediated process is controlled via the initial CPDA concentration. The molecular weight of the polystyrene from the solution (PS_free) shows a linear behavior with conversion and has a low polydispersity index. Furthermore, the loading of the grafted solid phase shows a linear relationship with the molecular weight of PS_free for both regimes. Regime 2 has a higher loading capacity per molecular weight than regime 1. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4180–4192, 2002     

Visible light‐induced living surface grafting polymerization for the potential biological applications

A novel visible light‐induced living surface grafting polymerization was developed by a strategy in which isopropyl thioxanthone (ITX) was first photoreduced under UV light and sequentially coupled onto the surface of polymeric substrates, and the produced isopropyl thioxanthone‐semipinacol (ITXSP) “dormant” groups were subsequently reactivated under visible light to initiate a surface grafting polymerization. By using glycidyl methacrylate (GMA) and low‐density polyethylene (LDPE) films as models, a “living” surface grafting polymerization initiated by ITXSP under visible light at room temperature was observed. Both the surface grafting chain length versus grafting conversion of monomer and the grafting polymerization rate versus monomer concentration demonstrated a linear dependence, which is in accord with the known characteristics of living polymerization. The livingness rendered it possible to accurately control the thickness of the grafted layer by simply altering the irradiation time. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Phys, 2009     

Reduction of the Thrombogenicity of Polyethylene Membranes by Radiation Grafting

A new anti-thrombosis dialytic membrane with a hydrophilic-hydrophobic microphase structure was prepared by pre-irradiation grafting of -hydroxyethyl methacrylate (HEMA) and styrene (St) onto polyethylene (PE) membranes. The effects of reaction conditions on the degree of grafting were determined, and the properties of the grafted films were investigated. Compared with PE grafted with hydrophilic monomer, the antithrombogenicity and permeability of the PE-g-(HEMA-co-St) were 30 and 15 times higher than that of the ungrafted films, respectively, if the volume ratio (HEMA:St) is about 1:1.