Analysis of polystyrene surface properties on thin film bonding under carbon dioxide pressure using nanoparticle embedding technique

A gold nanoparticle embedding technique is used to determine how vacuum and pressured carbon dioxide (CO₂) affect polystyrene (PS) thin film properties. The pressured CO₂ greatly increased the gold nanoparticle embedding depth, possibly due to a low cohesive energy density near the film surface. For the monodisperse PS used in this study (M_n = 214,000), two spin‐coated thin films with intimate contact can be bonded below the bulk glass transition temperature (T_g) under CO₂ pressure when the embedded depth is larger than half of the gyration radius of PS molecules. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1535–1542, 2009     

Effect of sample preparation on the glass‐transition of thin polystyrene films

We have investigated the effect of sample preparation on the glass‐transition temperature (T_g) of thin films of polystyrene (PS). By preparing and measuring the glass‐transition temperature T_g of multilayered polymer films, we are able to assess the contribution of the spincoating process to the reduced T_g values often reported for thin PS films. We find that it is possible to determine a T_g even on the first heating cycle, and that by the third heating cycle (a total annealing time of 15 min at T = 393 K) the T_g value has reached a steady state. By comparing multilayered versus single layered films we find that the whole T_g depends only on the total film thickness, and not on the thickness of the individual layers. These results strongly suggest that the spincasting process does not contribute significantly to T_g reductions in thin polymer films. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4503–4507, 2004     

A novel temperature‐step method to determine the glass transition temperature of ultrathin polymer films by liquid dewetting

A novel temperature‐step experimental method that extends the Bodiguel‐Fretigny liquid dewetting method of investigating polymer thin films is described and results presented from an investigation of thickness effects on the glass transition temperature (T_g) of ultrathin polystyrene (PS) films. Unlike most other methods of thin film investigation, this procedure promises a rapid screening tool to determine the overall profile of T_g versus film thickness for ultrathin polymer films using a limited number of samples. Similar to our prior observations and other literature data, with this new method obvious T_g depression was observed for PS thin films dewetting on both glycerol and an ionic liquid. The results for PS dewetting on the two different liquids are similar indicating only modest effects of the substrate on the T_g‐film thickness relationship. In both instances, the T_g depression is somewhat less than for similar PSs supported on silicon substrates reported in the literature. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 1343–1349     

Pressure‐volume‐temperature and glass transition behavior of silica/polystyrene nanocomposite

The pressure‐volume‐temperature (PVT) behavior and glass transition behavior of a 10 wt % silica nanoparticle‐filled polystyrene (PS) nanocomposite sample are measured using a custom‐built pressurizable dilatometer. The PVT data are fitted to the Tait equation in both liquid and glassy states; the coefficient of thermal expansion α, bulk modulus K, and thermal pressure coefficient γ are examined as a function of pressure and compared to the values of neat PS. The glass transition temperature (T_g) is reported as a function of pressure, and the limiting fictive temperature (T_f′) from calorimetric measurements is reported as a function of cooling rate. Comparison with data for neat PS indicates that the nanocomposite has a slightly higher T_g at elevated pressures, higher bulk moduli at all pressures studied, and its relaxation dynamics are more sensitive to volume. The results for the glassy γ values suggest that thermal residual stresses would not be reduced for the nanocomposite sample studied. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1131–1138     

Indentation of poly(methyl methacrylate) under high‐pressure gases

The variation of the indentation hardness of a high molecular weight poly(methyl methacrylate) (PMMA) subjected to CO₂ and Ar at high pressure was measured in situ. The samples were subjected to gas exposure for 3 h at 40 °C before a conical indenter of an included angle at 105 °, with a fixed load of 0.237 kg, was applied for a loading time of 60 s. The data show that both CO₂ and Ar reduce the hardness of PMMA to a comparable extent at low pressures. The hardness of PMMA subjected to Ar indicates a minimum at about 4 MPa and then increases. CO₂ produced a monotone decreasing trend in hardness in the pressure range studied, and the glass‐transition temperature (T_g) was achieved at about 6.0 MPa. The change in hardness is attributed to plasticization of the polymer matrix that is more extensive for CO₂. The relationship between the change in hardness for this PMMA subjected to high‐pressure CO₂, the corresponding change in the T_g, and the associated swelling of the polymer is discussed. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 3020–3028, 2001     

A new technique for measuring retrograde vitrification in polymer–gas systems and for making ultramicrocellular foams from the retrograde phase

A stepwise temperature‐ and pressure‐scanning thermal analysis method was developed to measure glass‐transition temperature T_g in the two‐phase polymer–gas systems as a function of gas pressure p, and was used to confirm recent theoretical predictions that certain polymer–gas systems exhibit retrograde vitrification, that is, they undergo rubber‐to‐glass transition on heating. A complete T_g‐p profile delineating the glass–rubber phase envelope was established for the PMMA‐CO₂ system. The retrograde vitrification behavior observed, where at certain gas pressures the polymer exists in the rubbery state at low and high temperatures and in the glassy state at intermediate temperatures, was similar to that reported previously based on the creep‐compliance measurements. The existence of the rubbery state at low temperatures was used to generate foams by saturating the polymer with CO₂ at 34 atm and at temperatures in the range −0.2 to 24 °C followed by foaming at temperatures in the range 24 to 90 °C. Foams with very fine cell structure never reported before could be prepared by this technique. For example, PMMA foams with average cell size of 0.35 μm and cell density of 4.4 × 10¹³ cells/g were prepared by processing the low temperature rubbery phase. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 716–725, 2000     

Simultaneous kinetic and microdielectric studies of some epoxy–amine systems

Three reactive epoxy–amine systems based on diglycidyl ether of bisphenol A (DGEBA) with 4,4′-diaminodiphenylsulfone (DDS), 4,4′-methylenebis [3-chloro 2,6-diethylaniline] (MCDEA), and 4,4′-methylenebis [2,6-diethylaniline] (MDEA), were studied during isothermal curings at 140 and 160°C. The simultaneous kinetic and dielectric studies allow to express conductivity, σ, in terms of conversion, x, and of glass transition temperature, T_g. The conductivity, σ₀, of the initial monomer mixture and, σ_∞ of the fully cured network are measured. It is found that:

• The glass transition temperature, T_g, versus conversion, x, curves follows the equation of Di Benedetto modified by Pascault and Williams
• There exists a linear relation between log σ/log σ₀ and T_g.

So, it is possible to predict both kinetic and dielectric behaviors of these epoxy-amine systems by the knowledge of T_g0, ΔC_p0, and σ₀, respectively, glass transition temperature, heat capacity, and conductivity of initial monomer mixture, T_g∞ and ΔC_p∞, and σ_∞, respectively, glass transition temperature and heat capacity and conductivity of fully cured network. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 2911–2921, 1998     

Glass transition temperature of colloidal polystyrene dispersed in various liquids

Recently, there has been significant interest in measuring the glass transition temperature (T_g) of thin polymer films floated atop liquid substrates. However, such films still have intrinsically asymmetric interfaces, that is, a free surface and a liquid–polymer interface. In an effort to analyze the influence of different liquids on the T_g of confined polymers in which there is no interfacial asymmetry, a colloidal suspension of polystyrene (PS) nanoparticles (NPs) was employed. The T_gs of PS NPs suspended in either glycerol or an ionic liquid were characterized using differential scanning calorimetry. Nanoparticles suspended in an ionic liquid showed an invariance of T_g with confinement, that is, decreasing diameter. In contrast, nanoparticles suspended in glycerol showed a slight decrease in T_g with confinement. The dependence of NP T_g on the nature of the surrounding liquid exhibited a positive correlation with the interfacial energy of the liquid–PS interface and no correlation with interfacial softness, as measured by viscosity. A comparison of the results with thin films supported by liquid or solid substrates revealed a nontrivial interplay between interfacial softness and interfacial interactions on the T_g of confined PS. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1776–1783     

Effect of temperature and membrane preparation parameters on gas permeation properties of polymethacrylates

Permeabilities of N₂, Ar, O₂, CO₂, and H₂ gases in PEMA (Polyethylmethacrylate) membranes have been measured above and below glass transition in the temperature range of 25–70 °C. The permeabilities of the gases were observed increasing with temperature. Arrhenius plot of permeability versus temperature data showed that there is a slope discontinuity at near to T_g of PEMA. In addition, the effects of membrane preparation parameters by solvent casting method (percentage of polymer in solvent, annealing temperature, annealing time, evaporation temperature, and evaporation time) have been investigated by using homogenous dense membranes of PEMA. It is observed that membrane preparation parameters strongly affect the membrane performance and the reproducibility of the permeability measurements. On the other hand, the effect of polymer structure on membrane performance has been investigated. Comparison of the permeabilities of N₂, Ar, O₂, CO₂, and H₂ gases in PEMA and PMMA membranes shows that PMMA membranes have smaller permeabilities and higher selectivities than PEMA membranes because of their higher glass transition temperature, T_g. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3025–3033, 2007     

Sub‐glass‐transition temperature interface formation between an immiscible glass rubber pair

We used neutron reflectivity to measure the interfacial width in the immiscible system polystyrene/poly(n‐butyl methacrylate) (PS/PnBMA). Measurements were made on the same samples at temperatures ranging from below the glass‐transition temperature (T_g) of PS to slightly above. We observed significant broadening of the interface at temperatures below the T_g of PS, indicating chain mobility below the bulk T_g value. The interfacial width exhibited a plateau at a value of 20 Å in the temperature range of 365 K < T < 377 K. A control experiment involving hydrogenated and deuterated PS films (hPS/dPS) showed no such broadening over the same temperature region. The results are consistent with a reduction of the T_g of PS in the interfacial region of ～20 K. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2664–2670, 2001     

Effects of high-pressure CO2 on the glass transition temperature and mechanical properties of polystyrene

Hydrostatic pressure usually increases the glass transition temperature T_g of a polymer glass by decreasing its free volume; if the pressurizing environment is soluble in the polymer, however, one might expect an initial decrease in T_g with pressure as the polymer is plasticized by the environment. Just such a minimum in the T_g of polystyrene (PS) is observed as the pressure of CO₂ gas is increased over the range 0.1–105 MPa from both ultrasonic (1 MHz) measurements of Young's modulus E and static measurements of the creep compliance J. A time-temperature-pressure superposition law is obeyed by PS which allows a master curve for the compliance to be constructed and shift factors to be determined. A master curve for E is then obtained by using the Boltzmann superposition principle. The compliance J reaches a maximum, and E and T_g reach minima, at a CO₂ pressure of ca. 20 MPa at both 34 and 45°C, which are above the critical temperature (31°C) of CO₂. At the minimum, T_g is 41 at 45°C and 36 at 34°C, the larger depression at 34°C evidently corresponding to the higher solubility of CO₂ at the lower temperature. The plasticization effect due to CO₂ can be isolated by subtracting the effect of hydrostatic pressure alone from the experimental data. The results leave no doubt that at high pressures CO₂ gas is a severe plasticizer for polystyrene.     

Crossover in dynamics of polymeric liquids: Back to Tll?

Light scattering spectra of two polymers, polyisobutylene (PIB) and polystyrene (PS), were analyzed in the broad frequency range at temperatures above the glass transition (T_g ). At high temperatures, the spectra followed the qualitative scenario suggested by mode‐coupling theory (MCT) of the glass transition. The crossover temperature (T_c ) was defined to be approximately 1.35 T_g in PIB and approximately 1.15 T_g in PS. At lower temperatures (T < T_c ), the light scattering spectra deviated strongly from the idealized MCT scenario. Different signs of the dynamic transition around T_c are discussed. The difference between the suggested interpretation and an old idea of the liquid–liquid transition in polymeric liquids is stressed: we describe the transition as purely dynamic in nature. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2785–2790, 2000     

Thermal behavior of ferroelectric Polyamide 11 in relation to pyroelectric properties

The pyroelectric properties of oriented thin films of ferroelectric Polyamide 11 have been studied in the temperature range of −100°C up to +140°C. The temperature dependence of the experimental pyroelectric coefficient has been analyzed. Three changes of slope of the pyroelectric coefficient are observed at −20, +50, and +100°C. The origin of the lower temperature event has not yet been defined. The upper transition is attributed to chain movements in crystalline regions, and more precisely, to a crystalline phase transition. The intermediate event is close to the glass transition temperature T_g observed by DSC. It is attributed to the manifestation of the glass transition. Below T_g, the variations of the pyroelectric coefficient are very small. For higher temperatures, it increases rapidly, attesting to a major contribution of secondary pyroelectricity and dimensional effects above T_g. The breaking of hydrogen bonds occurring at the glass transition temperature observed on DSC thermograms does not affect pyroelectric properties. Pyroelectric properties are mildly reduced after annealing at temperatures up to +140°C. A comparative study of oriented ferroelectric films prepared by quenching from the melt and nonoriented slowly cooled samples has been carried out by means of DSC. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 715–723, 1999     

High‐pressure rheology and viscoelastic scaling predictions of polymer melts containing liquid and supercritical carbon dioxide

High‐pressure rheological behavior of polymer melts containing dissolved carbon dioxide (CO₂) at concentrations up to 6 wt % were investigated using a high‐pressure extrusion slit die rheometer. In particular, the steady shear viscosity of poly(methyl methacrylate), polypropylene, low‐density polyethylene, and poly(vinylidene fluoride) with dissolved CO₂ were measured for shear rates ranging from 1 to 500 s^?1 and under pressure conditions up to 30 MPa. The viscosity of all samples revealed a reduction in the presence of CO₂ with its extent dependent on CO₂ concentration, pressure, and the polymer used. Two types of viscoelastic scaling models were developed to predict the effects of both CO₂ concentration and pressure on the viscosity of the polymer melts. The first approach utilized a set of equations analogous to the Williams–Landel–Ferry equation for melts between the glass‐transition temperature (T_g) and T_g + 100 °C, whereas the second approach used equations of the Arrhenius form for melts more than 100 °C above T_g. The combination of these traditional viscoelastic scaling models with predictions for T_g depression by a diluent (Chow model) were used to estimate the observed effects of dissolved CO₂ on polymer melt rheology. In this approach, the only parameters involved are physical properties of the pure polymer melt that are either available in the existing literature or can be measured under atmospheric conditions in the absence of CO₂. The ability of the proposed scaling models to accurately predict the viscosity of polymer melts with dissolved high‐pressure CO₂ were examined for each of the polymer systems. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 3055–3066, 2001     

Nonlinear viscoelastic diffusion in concentrated polystyrene/ethylbenzene solutions

Nonlinear gradient-driven diffusion was studied in concentrated polystyrene (PS)/ethylbenzene (EB) solutions using vapor sorptions with a finite driving force. The nonlinear sorptions were carried out on thin films (≅2.05, 3.50 μ thick) at conditions where non-Fickian, “viscoelastic” effects appear. These data were modeled with the nonlinear diffusion equation studied by Tang. Four dimensionless material parameters in the model were determined from a limited amount of linear-response, differential sorption data on PS/EB mixtures measured in the same range of experimental conditions as for the nonlinear sorptions. The nonlinear model successfully predicts the observed nonlinear response either above or below the glass transition (T_g). In order to simultaneously capture the nonlinear response both above and below T_g, the abrupt change in the concentration dependence of physical properties at T_g must be accounted for. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 2103–2119, 1997     

Effect of nanoscale confinement on the glass transition temperature of free-standing polymer films: Novel,self-referencing fluorescence method

The effect of nanoscale confinement on the glass transition temperature, T_g, of freely standing polystyrene (PS) films was determined using the temperature dependence of a fluorescence intensity ratio associated with pyrene dye labeled to the polymer. The ratio of the intensity of the third fluorescence peak to that of the first fluorescence peak in 1-pyrenylmethyl methacrylate-labeled PS (MApyrene-labeled PS) decreased with decreasing temperature, and the intersection of the linear temperature dependences in the rubbery and glassy states yielded the measurement of T_g. The sensitivity of this method to T_g was also shown in bulk, supported PS and poly(isobutyl methacrylate) films. With free-standing PS films, a strong effect of confinement on T_g was evident at thicknesses less than 80–90 nm. For MApyrene-labeled PS with M_n = 701 kg mol⁻¹, a 41-nm-thick film exhibited a 47 K reduction in T_g relative to bulk PS. A strong molecular weight dependence of the T_g-confinement effect was also observed, with a 65-nm-thick free-standing film exhibiting a reduction in T_g relative to bulk PS of 19 K with M_n = 701 kg mol⁻¹ and 31 K with M_n = 1460 kg mol⁻¹. The data are in reasonable agreement with results of Forrest, Dalnoki-Veress, and Dutcher who performed the seminal studies on T_g-confinement effects in free-standing PS films. The utility of self-referencing fluorescence for novel studies of confinement effects in free-standing films is discussed. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2754–2764, 2008     

Molecular dynamics simulations of the effects of carbon dioxide on the interfacial bonding of polystyrene thin films

Fabrication of nanoscale polymer‐based devices, especially in biomedical applications, is a challenging process due to requirements of precise dimensions. Methods that involve elevated temperature or chemical adhesives are not practicable due to the fragility of the device components and associated deformation. To effectively fabricate devices for lab‐on‐a‐chip or drug delivery applications, a process is required that permits bonding at low temperatures. The use of carbon dioxide (CO₂) to assist the bonding process shows promise in reaching this goal. It is now well established that CO₂ can be used to depress the glass transition temperature (T_g) of a polymer, allowing bonding to occur at lower temperatures. Furthermore, it has been shown that CO₂ can preferentially soften a polymer surface, which should allow for effective bonding at temperatures even below the bulk T_g. However, the impact of this effect on bonding has not been quantified, and the optimal bonding temperature and CO₂ pressure conditions are unknown. In this study, a molecular dynamics model is used to examine the atomic scale behavior of polystyrene in an effort to develop understanding of the physical mechanisms of bonding and to quantify how the process is impacted by CO₂. The final result is the identification of a range of CO₂ pressure conditions which produce the strongest bonding between PS thin films at room temperature. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Viscoelasticity of nanobubble‐inflated ultrathin polymer films: Justification by the coupling model

The nanobubble inflation method is the only experimental technique that can measure the viscoelastic creep compliance of unsupported ultrathin films of polymers over the glass–rubber transition zone as well as the dependence of the glass transition temperature (T_g) on film thickness. Sizeable reduction of T_g was observed in polystyrene (PS) and bisphenol A polycarbonate by the shift of the creep compliance to shorter times. The dependence of T_g on film thickness is consistent with the published data of free‐standing PS ultrathin films. However, accompanying the shift of the compliance to shorter times, a decrease in the rubbery plateau compliance is observed. The decrease becomes more dramatic in thinner films and at lower temperatures. This anomalous viscoelastic behavior was also observed in poly(vinyl acetate) and poly (n‐butyl methacrylate), but with large variation in the change of either the T_g or the plateau compliance. By now, well established in bulk polymers is the presence of three different viscoelastic mechanisms in the glass–rubber transition zone, namely, the Rouse modes, the sub‐Rouse modes, and the segmental α‐relaxation. Based on the thermorheological complexity of the three mechanisms, the viscoelastic anomaly observed in ultrathin polymer films and its dependence on chemical structure are explained in the framework of the Coupling Model. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Polymer–nanoparticle interfacial interactions in polymer nanocomposites: Confinement effects on glass transition temperature and suppression of physical aging

The effects of confinement on glass transition temperature (T_g) and physical aging are measured in polystyrene (PS), poly(methyl methacrylate) (PMMA), and poly(2-vinyl pyridine) (P2VP) nanocomposites containing 10- to 15-nm-diameter silica nanospheres or 47-nm-diameter alumina nanospheres. Nanocomposites are made by spin coating films from sonicated solutions of polymer, nanofiller, and dye. The T_gs and physical aging rates are measured by fluorescence of trace levels of dye in the films. At 0.1–10 vol % nanofiller, T_g values can be enhanced or depressed relative to neat, bulk T_g (T_g,bulk) or invariant with nanofiller content. For alumina nanocomposites, T_g increases relative to T_g,bulk by as much as 16 K in P2VP, decreases by as much as 5 K in PMMA, and is invariant in PS. By analogy with thin polymer films, these results are explained by wetted P2VP–nanofiller interfaces with attractive interactions, nonwetted PMMA–nanofiller interfaces (free space at the interface), and wetted PS–nanofiller interfaces lacking attractive interactions, respectively. The presence of wetted or nonwetted interfaces is controlled by choice of solvent. For example, 0.1–0.6 vol % silica/PMMA nanocomposites exhibit T_g enhancements as large as 5 K or T_g reductions as large as 17 K relative to T_g,bulk when films are made from methyl ethyl ketone or acetic acid solutions, respectively. A factor of 17 reduction of physical aging rate relative to that of neat, bulk P2VP is demonstrated in a 4 vol % alumina/P2VP nanocomposite. This suggests that a strategy for achieving nonequilibrium, glassy polymeric systems that are stable or nearly stable to physical aging is to incorporate well-dispersed nanoparticles possessing attractive interfacial interactions with the polymer. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2935–2943, 2006     

Surface mobility and diffusion at interfaces of polystyrene in the vicinity of the glass transition

Symmetric polydisperse (M_w = 23 × 10⁴, M_w/M_n = 2.84) and monodisperse (M_w = 21 × 10⁴, M_w/M_n < 1.05) polystyrene (PS), and asymmetric polydisperse PS/poly(2,6-dimethyl 1,4-phenylene oxide) (PPO) interfaces have been bonded in the vicinity of the glass transition temperature (T_g) of PS. In a lap-shear joint geometry, strength develops in all cases with time to the fourth power, which indicates that it is diffusion controlled. Strength developing at short times at the polydisperse PS/PS interface, at 90°C, is higher than that at the monodisperse interface, at 92°C (at T_g − 13°C in both cases), presumably due to the contribution of the low molecular weight species. The decrease of strength at the PS/PPO interface when the bonding temperature decreases from 113 to 70°C, i.e., from T_g + 10°C to T_g − 33°C of the bulk PS, indicates a high molecular mobility at the surface as compared to that in the bulk, and can be expressed by a classical diffusion equation, which is valid above T_g (of the surface layer). © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 567–572, 1998