New poly(amide–imide) syntheses. XXI. Synthesis and properties of aromatic poly(amide–imide)s based on 2,6-bis(4-trimellitimidophenoxy)naphthalene and aromatic diamines

A novel polymer-forming diimide–diacid, 2,6-bis(4-trimellitimidophenoxy)naphthalene, was prepared by the condensation reaction of 2,6-bis(4-aminophenoxy)naphthalene with trimellitic anhydride (TMA). A series of novel aromatic poly(amide–imide)s containing 2,6-bis(phenoxy)naphthalene units were prepared by the direct polycondensation of the diimide–diacid with various aromatic diamines using triphenyl phosphite (TPP) in N-methyl-2-pyrrolidone (NMP)/pyridine solution containing dissolved calcium chloride. Thirteen of the obtained polymers had inherent viscosities above 1.01 dL/g and up to 2.30 dL/g. Most of polymers were soluble in polar solvents such as DMAc and could be cast from their DMAc solutions into transparent, flexible, and tough films. These films had tensile strengths of 79–117 MPa, elongation-at-break of 7–61%, and initial moduli of 2.2–3.0 GPa. The wide-angle X-ray diffraction revealed that some polymers are partially crystalline. The glass transition temperatures of some polymers could be determined with the help of differential scanning calorimetry (DSC) traces, which were recorded in the range 232–300°C. All the poly(amide–imide)s exhibited no appreciable decomposition below 450°C, and their 10% weight loss temperatures were recorded in the range 511–577°C in nitrogen and 497–601°C in air. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 919–927, 1998     

Spacer‐length‐dependent association in polymers with multiple‐hydrogen‐bonded end groups

Herein, we investigate the influence of spacer length on the homoassociation and heteroassociation of end‐functionalized hydrogen‐bonding polymers based on poly(n‐butyl acrylate). Two monofunctional ureido‐pyrimidinone (UPy) end‐functionalized polymers were prepared by atom transfer radical polymerization using self‐complementary UPy‐functional initiators that differ in the spacer length between the multiple‐hydrogen‐bonding group and the chain initiation site. The self‐complementary binding strength (K_dim) of these end‐functionalized polymers was shown to depend critically on the spacer length as evident from ¹H NMR and diffusion‐ordered spectroscopy. In addition, the heteroassociation strength of the end‐functionalized UPy polymers with end‐functionalized polymers containing the complementary 2,7‐diamido‐1,8‐naphthyridine (NaPy) hydrogen‐bond motif is also affected when the aliphatic spacer length is too short. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Main‐chain,thermotropic, liquid‐crystalline,hydrogen‐bonded polymers of 4,4′‐bipyridyl with aliphatic dicarboxylic acids

A series of main‐chain, thermotropic, liquid‐crystalline (LC), hydrogen‐bonded polymers or self‐assembled structures based on 4,4′‐bipyridyl as a hydrogen‐bond acceptor and aliphatic dicarboxylic acids, such as adipic and sebacic acids, as hydrogen‐bond donors were prepared by a slow evaporation technique from a pyridine solution and were characterized for their thermotropic, LC properties with a number of experimental techniques. The homopolymer of 4,4′‐bipyridyl with adipic acid exhibited high‐order and low‐order smectic phases, and that with sebacic acid exhibited only a high‐order smectic phase. Like the homopolymer with adipic acid, the two copolymers of 4,4′‐bipyridyl with adipic and sebacic acids (75/25 and 25/75) also exhibited two types of smectic phases. In contrast, the copolymer of 4,4′‐bipyridyl with adipic and sebacic acids (50/50), like the homopolymer with sebacic acid, exhibited only one high‐order smectic phase. Each of them, including the copolymers, had a broad temperature range of LC phases (36–51 °C). The effect of copolymerization for these hydrogen‐bonded polymers on the thermotropic properties was examined. Generally, copolymerization increased the temperature range of LC phases for these polymers, as expected, with a larger decrease in the crystal‐to‐LC transition than in the LC‐to‐isotropic transition. Additionally, it neither suppressed the formation of smectic phases nor promoted the formation of a nematic phase in these hydrogen‐bonded polymers, as usually observed in many thermotropic LC polymers. The thermal transitions for all of them, measured by differential scanning calorimetry, were well below their decomposition temperatures, as measured by thermogravimetric analysis, which were in the temperature range of 193–210 °C. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1282–1295, 2003     

Synthesis and characterization of hydrogen‐bonded thermotropic liquid crystalline aromatic‐aliphatic poly(ester–amide)s from amido diol

Fifteen highly regular hydrogen‐bonded, novel thermotropic, aromatic‐aliphatic poly(ester–amide)s (PEAs) were synthesized from aliphatic amido diols by melt polycondensation with dimethyl terephthalate and solution polycondensation with terephthaloyl chloride. Intermolecular hydrogen bonds more or less perpendicular to the main‐chain direction induce the formation and stabilization of liquid crystalline property for these PEAs. The structure of these polymers, even in the mesomorphic phase is dominated by hydrogen bonds between the amide–amide and amide–ester groups in adjacent chains. Aliphatic amido diols were synthesized by the aminolysis of γ‐butyrolactone, δ‐valerolactone and ε‐caprolactone with aliphatic diamines containing a number of methylene groups from two to six in isopropanol medium at room temperature. Effects of polarity of the solvent on solution polymerization and effect of catalyst on trans esterification were studied. These polymers were characterized by elemental analysis, FTIR, ¹H NMR, ¹³C NMR, solubility studies, inherent viscosity, DSC, X‐ray diffraction, polarized light microscopy, and TGA. All the melt/solution polycondensed PEAs showed multiple‐phase transitions on heating with second transitions identified as nematic/smectic/spherullitic texture. The mesomorphic properties were studied as a function of their chemical structure by changing alternatively m or n. Odd‐even effect on mesophase transition temperature, isotropization temperature, and crystallinity were studied. The effect of molecular weight and polydispersity on mesophase/isotropization temperature and thermal stability were investigated. It was observed that there exists a competition for crystallinity and liquid crystallinity in these PEAs © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2469–2486, 2000     

Graft copolymers prepared by ethoxylation of polyamide 12 and poly(ethylene-co-vinyl alcohol)

Graft copolymers consisting of polyamide 12 or poly(ethylene-co-vinyl alcohol) as backbone polymers and side chains of poly(ethylene oxide) have been synthesized. The amide and hydroxyl groups of the backbone polymers were used as initiation sites for the polymerization of ethylene oxide (EO). Potassium tert-butoxide was used for ionization of the active groups, and the polymerization of EO was carried out in dimethyl sulfoxide. The graft copolymers were characterized with respect to molecular weight and composition using elemental analysis, ¹H-NMR, gel permeation chromatography, and FTIR. The size of the side chains varied between 300 and 1000 g/mol. Thermal properties were examined by DSC. The graft copolymers showed increasing crystallinity and increasing melt temperature with increasing molecular weight of the side chains. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 803–811, 1998     

Poly(ester amide)s derived from glycine,even‐numbered diols,and dicarboxylic acids: Considerations on the packing

A new sequential poly(ester amide) derived from 1,12‐dodecanediol, sebacic acid, and glycine was synthesized and characterized. Its crystalline structure was studied with transmission electron microscopy and X‐ray diffraction. The results were compared with results for a related polymer, derived from glycine, 1,6‐hexanediol, and succinic acid, that produced a lower methylene/carbonyl ratio. The crystalline structures of both polymers corresponded to a periodic arrangement of two layers of hydrogen‐bonded molecular chains, whose polymethylene sequences mimicked the packing of polyethylene and the majority of polyesters. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 1036–1045, 2001     

Structure and morphology of nylon 2 4 lamellar crystals: Comparison with polypeptides and relationship with other nylons

Chain-folded lamellar crystals of nylon 2 4 have been prepared from dilute solution by addition of poor solvent. Two crystal structures are observed at room temperature: a monoclinic form I, precipitated at elevated temperature, and a less-defined, orthorhombic form II, precipitated at room temperature. The unit cell parameters for both forms are similar to those reported for its isomer, nylon 3. Nylon 2 4 form II is a liquid–crystal-like or disordered phase, consisting of hydrogen-bonded sheets in poor register in the hydrogen bond direction. Form I crystals have two characteristic interchain spacings of 0.41 nm and 0.39 nm at room temperature and on heating, exhibit a structural transformation and a Brill temperature (250°C) characteristic of many other even–even nylons. Nylon 2 4 is a member of the nylon 2 Y and nylon 2N 2(N+1) families, and the form I crystals show behavior commensurate with both. We propose they contain a proportion of intersheet hydrogen bonds at room temperature, similar to that for the nylon 2 Y family, and the short dimethylene alkane segments mean that the structure consists of hydrogen-bonded a-sheets, with an amide unit in each fold, similar to that of nylon 4 6. The fold geometry and sheet structure is compared with chain-folded apβ-sheet polypeptides and nylon 3. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. B Polym. Phys. 36: 2401–2412, 1998     

Synthesis and characterization of poly(aryl ether)s containing the pyrimidine moiety

A series of new poly(aryl ether)s containing the pyrimidine moiety were prepared by a nucleophilic aromatic substitution polymerization reaction in an aprotic solvent (DMAc) in the presence of excess potassium carbonate. These polymers are high molecular weight, amorphous, and soluble in common solvents at room temperature. The polymers are easily cast from solution into flexible, colorless, and transparent films. They showed high glass transition temperatures ranging from 198 to 304°C by DSC analysis. The 5% weight losses by thermogravimetric analysis ranged from 478 to 580°C, indicating that these polymers are very thermostable in nitrogen and air. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1107–1110, 1998     

Synthesis and investigation of the effect of nematic phases on the glass‐transition behavior of novel cycloaliphatic liquid‐crystalline poly(ester amide)s

We designed and developed novel cycloaliphatic liquid‐crystalline (LC) poly(ester amide)s to investigate the effects of nematic LC phases and hydrogen‐bonding interactions on the glass‐transition behavior. Three series of poly(ester amide)s based on commercially important poly(1,4‐cyclohexanedimethylene terephthalate) were synthesized with two new cycloaliphatic diamines {3,8‐bis(aminomethyl)‐tricyclo [5.2.1.0.(2,6)]decane (tricyclic) and 1,3‐cyclohexane bismethylene amine (monocyclic)} and a linear counterpart (1,6‐hexamethylene diamine). The compositions of the ester/amide units in the copolymers were varied up to 50% by the adjustment of the amounts of the diol and diamine in the feed. The structures of the polymers were confirmed with NMR and Fourier transform infrared, and their inherent viscosities were measured at 30 °C with an Ubbelohde viscometer. Thermal analysis revealed that the poly(ester amide)s having less than 25 mol % amide linkages were thermotropic and LC, and threadlike nematic phases were observed under a polarizing microscope. The introduction of nematic, LC phases drastically affected the glass‐transition temperatures of the copolymers, and a plot of the composition versus the glass‐transition temperature passed through a maximum for lower amide incorporation, regardless of the structural differences of the amide units (cyclic or linear). This nonlinear Flory–Fox trend was correlated to the cooperative effect of the strong alignment of polymer chains in the nematic phases and intermolecular packing induced by the hydrogen bonding in the poly(ester amide)s. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5557–5571, 2006     

Equilibrium structure of hydrogen-bonded polymer blends

Deuterium-labeled polystyrene modified by random distributions of the comonomer p-(1,1,1,3,3,3-hexaflouro-2-hydroxyisopropyl)-α-methyl-styrene [DPS(OH)] has been blended with poly(butyl methacrylate) (PBMA) and studied with small-angle neutron scattering (SANS). Miscibility is induced via hydrogen bonding between the DPS(OH) hydroxyl group and PBMA carbonyl groups. The data suggest that the nature of the miscible-phase structure in these blends differs from that of the usual homopolymer blends at small scattering angles, which we attribute to the short-range site specific nature of the hydrogen bond interaction. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 2745–2750, 1998     

New poly(amide–imide)s syntheses. XXIII. Synthesis and properties of poly(amide–imide)s derived from 4,4′‐[1,4‐phenylenebis(isopropylidene‐1,4‐phenyleneoxy)]dianiline and various bis(trimellitimide)s

A series of poly(amide–imide)s III_a–m containing flexible isopropylidene and ether groups in the backbone were synthesized by the direct polycondensation of 4,4′‐[1,4‐phenylenebis(isopropylidene‐1,4‐phenyleneoxy)]dianiline (PIDA) with various bis(trimellitimide)s II_a–m in N‐methyl‐2‐pyrrolidone (NMP) using triphenyl phosphite and pyridine as condensing agents. The resulting poly(amide–imide)s had inherent viscosities in the range of 0.80–1.36 dL/g. Except for those from the bis(trimellitimide)s of p‐phenylenediamine and benzidine, all the polymers could be cast from DMAc into transparent and tough films. They exhibited excellent solubility in polar solvents. The 10% weight loss temperatures of the polymers in air and in nitrogen were all above 495°C, and their T_g values were in the range of 201–252°C. Some properties of poly(amide–imide)s III were compared with those of the corresponding poly(amide–imide)s V prepared from the bis(trimellitimide) of diamine PIDA and various aromatic diamines. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 69–76, 1999     

Living polymers. Their discovery,characterization, and properties

The story of the discovery of living polymers is presented. Living polymers are polymers that retain their ability to propagate and grow to a desired size while their degree of termination or chain transfer is still negligible. Theoretical and mechanistic considerations are discussed. The living polymerization technique provides access to uniform polymers (Poisson molecular weight distribution) of controllable size, block copolymers, functional polymers, and star and comb-shaped polymers. The quantitative aspects of electron transfer are fully discussed. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: ix–xv, 1998     

Spectroscopic studies of interactions in poly(N‐acryloyl‐N′‐methylpiperazine)/acidic polymer complexes

Poly(N‐acryloyl‐N′‐methylpiperazine) (PAMP) forms complexes with four strong acidic polymers, namely, poly(styrenesulfonic acid), poly(vinylphosphonic acid), poly(acrylic acid) and poly(methacrylic acid) in ethanol/water (1:1) solution. The nature of interpolymer interactions in various complexes was studied by Fourier transform infrared (FTIR) spectroscopy and X‐ray photoelectron spectroscopy (XPS). Both the carbonyl oxygen and the amide nitrogen of PAMP are involved in hydrogen‐bonding interactions. Some of the amine nitrogens of PAMP are protonated and therefore PAMP also interacts with the acidic polymers through ionic interactions. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 501–508, 2000     

Synthesis and characterization of novel poly(amide urea)s,materials with outstanding mechanical properties

Four novel A‐B condensation monomers containing an amine and a carboxylic acid function are described, along with their polymerization to give main chain aromatic poly(amide urea)s. The monomers, and the polymer structural unit, are N,N′‐diphenylurea derivatives. When comparing wholly aromatic polyamides, or aramids, with the poly(amide urea)s described herein, we find that the chemical resistance to hydrolysis of the later polymers increases and their thermal resistance is diminished due to the main chain urea groups, whereas their water uptake is not greatly modified. The most striking result of the new poly(amide urea)s is their outstanding mechanical resistance: their Young's modulus rises as high as 5.5 GPa and their tensile strengths as high as 170 MPa for unoriented films prepared at laboratory scale by casting. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5398–5407, 2007     

Infrared spectroscopic study of the interactions of nylon‐6 with water

We studied the interactions of nylon‐6 with water by following the Fourier transform infrared spectra of a hydrated thin film during dehydration. Very small changes in the spectra caused by the interactions were clearly revealed by the application of spectral subtraction. The water was found to interact with amide groups to form hydrogen bonds with non‐hydrogen‐bonded or free C?O and NH groups in the amorphous portion in the first hydration sphere. This was deduced from an analysis of minus and plus peaks appearing around the absorptions of the NH stretching, amide I band, and amide II bands in the difference spectra between the spectra during dehydration and the one at the most dehydration. The interactions of the amide groups with water were significantly stronger than the hydrogen bond between CO and NH in the crystalline portion, according to the magnitude of the frequency shift of relevant bands. Water, as the interacting counterpart, showed a distorted OH stretching absorption with two close peaks at about 3450 cm^?1. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1722–1729, 2003     

Oxidative polymerization of phenylenediamines catalyzed by horseradish peroxidase

Ortho-, meta-, and para-phenylenediamines were polymerized using hydrogen peroxide as an oxidant and horseradish peroxidase as a catalyst in mixed solvents of 1,4-dioxane and water. The yield of the polymers was strongly dependent on solvent composition, and maximum yields were obtained at 15–30% 1,4-dioxane. The analysis of circular dichroic spectra of the enzyme suggested that enzyme structure was significantly modified at high 1,4-dioxane contents, which may be responsible for the decrease of catalytic activity of the enzyme. On the basis of IR and electronic spectra of the polymers, it was considered that o- and p-phenylenediamine polymers retain disubstituted benzene nuclei, which suggests that the polymerization proceeded mainly via N—N coupling. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A Polym. Chem. 36: 2593–2600, 1998     

Vinyl monomers bearing chromophore moieties and their polymers. V. Synthesis and fluorescence behavior of a vinyloxy monomer bearing electron-accepting chromophore moiety,N-(2-(vinyloxy)ethyl)-1,8-naphthalimide,and its polymer

A vinyloxy monomer bearing electron-accepting chromophore, N-(2-(vinyloxy)ethyl)-1,8-naphthalimide (VOENI), was synthesized by reaction of potassium 1,8-naphthalimide with 2-chloroethyl vinyl ether. VOENI can be homopolymerized by cationic initiation and copolymerized with maleic anhydride (MAn) under radical initiation. The fluorescence behaviors of VOENI and its polymers were investigated. It has been found that the fluorescence intensity of the VOENI monomer is much lower than that of its polymers at the same chromophore concentration. This means that a “structural self-quenching effect” (SSQE) has been also observed in the vinyloxy monomer consisting of an electron-accepting chromophore, which has opposite electronic structure in comparison with acrylates bearing electron-donating chromophores as we have reported previously. The SSQE is attributed to the charge-transfer interaction between the electron-accepting chromophore and the electron-donating double bond in the same molecule. The fluorescence quenching of 1,8-naphthalic anhydride and P(VOENI-co-MAn) by ethyl vinyl ether (EVE), dihydrofuran, triethylamine (TEA), etc. evidences that the electron-rich vinyloxy group does act as an important role in the SSQE of VOENI. C₆₀ can also quench the fluorescence of the polymers, and an upward deviation from the linearity of the Stern–Volmer plot was observed showing that C₆₀ acted as a powerful electron donor to quench the fluorescence of the copolymer. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1111–1116, 1998     

Dynamic rheo-optical characterization of uniaxially oriented polyamide 11

Dynamic mechanical analysis, coupled with polarized step-scan FTIR transmission spectroscopy, has been used to monitor the submolecular motional behavior of uniaxially oriented polyamide 11. The dynamic in-phase spectra depend upon the morphology of the samples as well as on the polarization direction of the infrared radiation. The lineshape features of the dynamic in-phase spectra and their relationship to sample deformation are analyzed on the basis of changes of the internal coordinates, the reorientation movement of several functional groups, and the thickness change of the film during the stretching cycle. Dynamic infrared spectra are helpful for deconvolution of overlapping bands on the basis of their different responses to the external perturbation, which sometimes cannot be resolved well by derivative spectroscopy or curve-fitting analysis. The lineshape features have been used to follow microstructural changes after isothermal heat treatment. Near the N H stretching frequency, two bands at 3270 cm⁻¹ and 3200 cm⁻¹ are resolved and analyzed in terms of Fermi resonance between the N H stretching fundamental mode and the overtone and combination modes of the amide I and II vibrations. The dynamic response of the N H stretching mode correlates with the modulation of hydrogen bond strength in uniaxially oriented PA-11. After thermal treatment at the highest temperature (190°C), the dynamic response in this region is mainly caused by the modulation of crystals. In amide I region, three bands at 1680 cm⁻¹, 1648 cm⁻¹, and 1638 cm⁻¹ are separated and assigned to hydrogen bond-free, hydrogen-bonded amorphous, and hydrogen-bonded crystalline regions, respectively. The dynamic responses of the hydrogen-bonded regions are more sensitive to external perturbation. Two components are found in the amide II region, and the band at 3080 cm⁻¹ is assigned to the overtone resonance of the component with perpendicular polarization. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 2895–2904, 1998     

Synthesis and gas transport properties of random amide imide copolymers

Fully imidized random amide imide copolymers (rPAI) can be prepared in an aprotic solvent from trimellitic anhydride chloride (TMAc) and mixtures of various aromatic diamines via condensation polymerization. The polymers are soluble in a number of aprotic organic solvents including 1‐methyl‐2‐pyrrolidinone (NMP), N,N‐dimethylacetamide (DMAc), N,N‐dimethylformamide (DMF), and dimethylsulfoxide (DMSO). The gas transport properties of the rPAI materials are governed by the local structure around both the amide and imide linkages and can be tuned by the choice and ratio of diamines used. Significant improvement in selectivity relative to polyimides can be achieved. When inorganic carbonate salts are used to scavenge byproduct hydrogen chloride, the amount of residual salt in the dense films has a substantial effect on their gas transport properties. A fugitive salt process was identified, which eliminated this problem of residual inorganic salts. The activation energy for O₂, N₂, He, CO₂, and CH₄ permeability was determined for one of the copolymers. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1951–1965, 2000     

Monte carlo simulation of copolymerization by ester interchange reaction in miscible polyester blends

The effects of reaction variables on the degree of randomness in copolymers formed by ester interchange reaction in miscible polyester melt blends were systematically investigated using a Monte Carlo method. Three reaction variables such as the molecular weight difference between two component polymers, the blend ratio, and the reaction ratio of end attack to bond flip, were particularly considered on the cubic lattice model. Ester interchange reactions were assumed to take place during reptational chain motions. It was found that the copolymerization was dependent upon the molecular weight difference and reaction ratio: As the molecular weight difference becomes smaller and when both end attack and bond flip reactions are involved simultaneously, the copolymerization is accelerated. However, the blend ratio does not affect the copolymerization process. This result is discussed in relation to the polymer chain conformation for the ester interchange reaction. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1637–1645, 1998