Effect of interchange reactions on the molecular weight distribution of poly(ethylene terephthalate): A Monte Carlo simulation

The effect of the interchange reactions of poly(ethylene terephthalate) (PET) on its molecular weight distribution (MWD) was analyzed using a Monte Carlo simulation method. Three kinds of motions, which correspond to the direct ester(SINGLEBOND)ester interchange reaction, alcoholysis, and internal alcoholysis in polyester, were performed in this simulation: bond flip, end attack, and backbite. Two systems with two different types of nonequilibrium distribution (monodisperse and bimodal distribution) were initially prepared. The initial biases from equilibrium MWD are rapidly relaxed to an equilibrium MWD as the reaction progresses. The MWD at equilibrium is well described by the most probable MWD proposed by Flory. From the polydispersity data, it is concluded that about 0.3 interchanges per segment are sufficient to equilibrate the nonequilibrium system. For the validity of the simulation, the variation of MWD of the mixtures of two PETs having different molecular weights were monitored using gel permeation chromatography. The agreement between simulation and experiment is remarkably good. © 1996 John Wiley & Sons, Inc.     

Origin of miscibility‐induced sequential reordering and crystallization‐induced sequential reordering in binary copolyesters: a Monte Carlo simulation

The effect of the repulsive interaction between the components of binary copolyesters on their sequence order was investigated with the Monte Carlo simulation method. The phase separation and ester‐interchange reactions were implemented simultaneously with a kind of one‐site bond fluctuation model. When the repulsive interaction energy was applied to the binary copolyesters, miscibility‐induced sequential reordering (MISR) was induced. The more repulsive the pair interaction was, the higher the sequence order was. During the MISR process, homoester‐interchange reactions became more favorable because of the repulsive interaction, accompanying the decrease of the interactional free energy. The sequence order resulting from MISR was independent of the relative trial ratio of phase separation to ester‐interchange reaction at a given value of interaction energy. Restoration of the sequence distribution was also simulated with and without the repulsive interaction between the components of the binary copolyesters to investigate the effect of MISR on the crystallization‐induced sequential reordering (CISR) process in binary copolyesters, where sequences with lengths longer than 6 were assumed to crystallize and could not take part in ester‐interchange reactions. The sequence distribution in the amorphous phase was restored via ester‐interchange reactions. When the repulsive interaction was applied to binary copolyesters during the CISR process, restoration of the sequence distribution was accelerated, indicating that MISR can accelerate the CISR process when a polyester blend shows upper critical solution temperature behavior. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1337–1347, 2001     

Homogenization process caused by competition between phase separation and ester‐interchange reactions in immiscible polyester blends: A Monte Carlo simulation

The homogenization process caused by competition between phase separation and ester‐interchange reactions in immiscible polyester blends was investigated via the Monte Carlo simulation method. Phase separation and ester‐interchange reactions were performed simultaneously with the one‐site bond fluctuation model on a homogeneous blend of immiscible polyesters. Three different values of the repulsive pair‐interaction energy (E_AB) between segments A and B and two trial ratios of phase separation to ester‐interchange reactions at a given E_AB were introduced to examine the competition between them. Phase separation was monitored by the calculation of the collective structure factor, and copolymerization was traced by the calculation of the degree of randomness (DR). In all cases, as the homogenization proceeded, the maximum intensity of the collective structure factor initially increased, reached a maximum, and finally decreased, whereas the peak position where the structure factor had a maximum shifted downward in the early stage and then remained unchanged after the intensity of the collective structure factor reached the maximum. This indicates that during the homogenization process, the domain size did not change significantly after phase‐separated structures were developed distinctly. In this simulation, phase‐separated structures were traced until the DR was above 0.8. This result indicates that homogenization can be accomplished via homogeneous ester‐interchange reactions over most of the polyester chains because copolyesters resulting from ester‐interchange reactions do not act as an efficient compatibilizer. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 590–598, 2000     

Phase separation in semicrystalline blends of poly(phenylene sulfide) and poly(ethylene terephthalate). I. Preparation of poly(phenylene sulfide)-graft-poly(ethylene terephthalate) copolymers by ester interchange and characterization utilizing the model compound 2,4-bis(phenylthio benzoic acid)

Blends of carboxyl functionalized poly(phenylene sulfide) (PPS) and poly(ethylene terephthalate) (PET) were shown to undergo an ester interchange reaction during melt blending. Pendent carboxyl functionality randomly incorporated along the PPS chain reacts with the ester moiety of PET to form a graft copolymer. A model compound, 2,4-bis(phenylthio benzoic acid), has been synthesized to assist in defining the level of carboxyl functionality on the PPS chain. Evidence of the grafting reaction has been gathered from infrared spectroscopy, solubility measurements, and electron microscopy. When added to blends of PPS and PET homopolymers, the graft copolymer significantly reduces the average domain size of the dispersed phase across the entire composition range. This study describes the role that graft copolymers formed by ester interchange reactions can play in compatibilizing this immiscible blend system, with particular focus on the conditions leading to increased grafting efficiency. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3473–3485, 1999     

A theoretical investigation of the production of branched copolymers in continuous stirred tank reactors

A comprehensive mathematical model for free-radical copolymerization reactions has been developed for a homogeneous continuous stirred tank reactor. The present model is based on a fairly general copolymerization scheme accounting for the formation of linear and branched copolymer chains. Both chain transfer to polymer and terminal double bond reactions are considered in order to predict the long chain branching frequency. Changes in molecular weight, composition and degree of branching occurring during the copolymerization reaction are modelled using the method of moments. To break-down the dependence of the moment equations on higher order moments two different closure methods are considered. The predictive capabilities of the model are examined in relation to the solution copolymerization of methyl methacrylate with vinyl acetate. It is shown that both chain transfer to polymer and terminal double bond reactions significantly contribute to the broadening of the molecular weight and degree of branching distributions. Furthermore, the terminal double bond reaction effects significantly the copolymer number-average molecular weight and the concentration of terminal double bonds.     

A theoretical study of the comonomer effect in the ethylene polymerization with zirconocene catalytic systems

The PM3(tm) semiempirical method has been used to optimize the structures for the reactants and transition states of the first and second ethylene insertion processes into zirconocene catalytic systems. The results obtained for these reactions are compared with calculations published in the literature performed at different ab-initio theoretical levels. The agreement between our calculations and those reported in the literature is satisfactory. Taking advantage of the reduced computational effort required in semiempirical calculations two additional processes related with the so-called comonomer effect were also studied: ethylene/1-hexene copolymerization, and chain termination reaction, both in the homopolymerization and in copolymerization of ethylene with 1-hexene comonomer. The calculated activation energies support some experimental findings such as the higher polymerization activities in the presence of comonomers and also the molecular weight reduction of the copolymers due to the more favorable β-elimination reactions. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1157–1167, 1998     

Some novel accelerating agents for nitroxide‐mediated living free‐radical polymerization

Malononitrile (MN), trifluoroacetic acid anhydride, acetylacetone, acetoacetic ester, and diethyl malonate have been identified as novel rate‐accelerating additives for nitroxide‐mediated living free‐radical polymerization. Among these additives, MN has the greatest accelerating effect. Adding MN at an MN/2,2,6,6‐tetramethylpiperidine‐oxyl (TEMPO) molar ratio of 4.0 results in a nearly 20 times higher rate of polymerization of styrene (St), and adding MN at an MN/TEMPO molar ratio of 2.5 results in a nearly 15 times higher rate of copolymerization of St and methyl methacrylate. The polymerization of St proceeds in a living fashion, as indicated by the increase in the molecular weight with time and conversion and the relatively low polydispersity. The polymerization rate of St is so quick that the conversion reaches 70% within 1 h at 125 °C when the molar ratio of MN to TEMPO is 4:1. Moreover, the reaction temperature can be reduced to 110 °C. A possible explanation for this effect is that the formation of hydrogen bonds between the MN and TEMPO moiety weakens the C? ON bond at the end of the polymer chain. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5246–5256, 2005     

Chemistry of olefin polymerization reactions with chromium‐based catalysts

Detailed GC analysis of oligomers formed in ethylene homopolymerization reactions, ethylene/1‐hexene copolymerization reactions, and homo‐oligomerization reactions of 1‐hexene and 1‐octene in the presence of a chromium oxide and an organochromium catalyst is carried out. A combination of these data with the analysis of ¹³C NMR and IR spectra of the respective high molecular weight polymerization products indicates that the standard olefin polymerization mechanism, according to which the starting chain end of each polymer molecule is saturated and the terminal chain end is a C?C bond (in the absence of hydrogen in the polymerization reactions), is also applicable to olefin polymerization reactions with both types of chromium‐based catalysts. The mechanism of active center formation and polymerization is proposed for the reactions. Two additional features of the polymerization reactions, co‐trimerization of olefins over chromium oxide catalysts and formation of methyl branches in polyethylene chains in the presence of organochromium catalysts, also find confirmation in the GC analysis. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5330–5347, 2008     

Obtaining aliphatic branched polycarbonates via simple copolymerization of trimethylene carbonate with cyclic carbonate containing pendant ester groups

Different possibilities for obtaining branched, functional carbonate copolymers are presented in this study. Copolymers were synthesized according to the ring‐opening polymerization (ROP) of the cyclic carbonate monomers, containing pendant ester groups. As an example, we chose copolymerization of ethyl 5‐methyl‐2‐oxo‐1,3‐dioxane‐5‐carboxylate (MTC‐Et) with trimethylene carbonate (TMC), using zinc (II) and lanthanum (III) acetylacetonates as ROP initiators. The transesterification processes of ester groups in pendant, short chains, appearing during conducted copolymerization, led to the establishment of two different fractions: first‐branched and high molecular weight fraction and second‐linear and low molecular weight. The content of this high‐molecular‐weight fraction increased with both: the amount of MTC‐Et in started reaction mixture and the time of conducted copolymerization. Reactivity constants in studied reaction were determined. It was possible to obtain the copolymer fraction (ca. 30%) with molecular weight of up to a million g/mol, with a highly branched chain microstructure using lanthanum (III) acetylacetonate as initiator. Conclusions were based on detailed NMR analysis, determining microstructure of the copolymer chains and additionally on GPC and DSC measurement. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 808–819     

Grafting onto wool. IV. Interaction of polymer radicals in the viscous media of wool fibers

In order to study the termination reaction of polymer radicals in the viscous media of wool fibers, reduced, methylated, and S-carboxymethylated wool fibers were used for graft copolymerization of methyl methacrylate and styrene. With termination of poly(methyl methacrylate) radicals, two different termination reactions, recombination and disproportionation, were together involved in the grafting systems studied. The occurrences of two termination reactions in the system could be correlated with the mobility of the wool chain controlling the radical end mobility. With decreasing disulfide content in the fibers, disproportionation predominantly takes place among the mobilized chains. At a constant disulfide, the thiol content or the concentration of thiol anions becomes the determining factor for the termination reaction. A possible explanation for these phenomena in terms of the thiol and disulfide interchange reaction is presented. On the grafting of styrene, additional evidence was obtained that prevention and retardation of the interchange reactions followed mechanochemical bond scission of the disulfide and other covalent bonds and produced new free radicals which could initiate chain reactions.     

Miscibility and transesterification in blends of liquid crystalline copolyesters and polyarylate

Blends of poly(oxybenzoate-p-ethylene terephthalate) (POB-PET) and polyarylate were confirmed to be a partially miscible system by differential scanning calorimetry. When 60/40 POB-PET/PAr blend was annealed at high temperature (above 270°C) for several minutes, the ester–ester interchange (transesterification) in the blend took place immediately, as evidenced by Fourier Transformed infrared analyses. The analysis of the blend annealed at 290°C by ¹H-¹³C nuclear magnetic resonance disclosed that there were four new diads appearing in 15 min and an additional one produced in 60 min during the heat treatment. The miscibility between POB-PET and polyarylate increased with the mol concentration of these new diads judging from differential scanning calorimetry. The evolution of the concentration of the diad ethylene glycol-isophthalate during the annealing can be described by a second-order reaction. The activation energy of forming the diad ethylene glycol-isophthalate was 26.5 kcal/mol, and the preexponential factor for the transesterification reaction is 3.7 × 10⁸ min⁻¹. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1959–1969, 1998     

Profile of oxidation in irradiated polyethylene

Following gamma irradiation in air which causes bond scission and yields large concentrations of peroxy radicals, maximum oxidation and an increase in crystallinity occurs on the surface of ultrahigh molecular weight polyethylene. Here, bimolecular reactions of peroxy radicals generate carbonyls, mostly ketones. On the polymer surface, peroxy radicals continue to react over time periods of years to generate carbonyls and chain scission. Peroxy radicals in the interior of the polymer abstract hydrogens and form hydroperoxides, inducing chain reactions and a slow but continue increase of ketone. Within the polymer sample, to a decreasing depth with increasing dose, a reduced concentration of oxygen is available to react with radiolytic radicals, so that more efficient crosslinking and a low level of hydroperoxide chain reaction occur. After long periods of time a surface maximum in carbonyl concentration is produced. Heating polyethylene in high pressures of oxygen accelerates the oxidative process. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 329–339, 1998     

Matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry study on copolymers obtained by the alternating copolymerization of bis(γ‐lactone) and epoxide with potassium tert‐butoxide

Oligomer samples obtained by the anionic copolymerization of a bis(γ‐lactone), 2,8‐dioxa‐1‐methylbicyclo[3.3.0]octane‐3,7‐dione ( 1 ), and glycidyl phenyl ether with potassium tert‐butoxide have been analyzed by matrix‐assisted laser desorption/ionization time‐of‐flight (MALDI‐TOF) mass spectrometry. The MALDI‐TOF mass spectra of these cooligomers show well‐resolved signals that can be reliably assigned to linear, alternating cooligomers that have carboxylate chain ends or alkoxide chain ends and cyclic ones. The formation of these three series of cooligomers suggests that the polymerization process involves concomitant intermolecular transesterification and intramolecular back‐biting. The intramolecular back‐biting reaction causes the formation of cyclic cooligomers, whereas the intermolecular transesterification causes the reduction of the molecular weight and the transformation of the alkoxide active chain end into a carboxylate chain end. The MALDI‐TOF mass spectrometry study has shown that an excess of monomer 1 enhances the selectivity of propagation by increasing the probability of the attack of the alkoxide chain end to 1 . © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2643–2649, 2005     

Synthesis of polyester having sequentially ordered two orthogonal reactive groups by anionic alternating copolymerization of epoxide and bislactone

This article presents a route to a novel polyester having sequentially ordered two orthogonal reactive groups. The polyester was given by the imidazole‐initiated alternating copolymerization of allyl glycidyl ether (AGE) and a bislactone 1 . This copolymerization system is characterized by the following three reaction behaviors: (1) the selective participation of only one of the two lactone moieties of 1 to the copolymerization to give a linear polyester, and the consequent introduction of the second lactone into the side chain of the polyester, (2) the participation of the epoxy moiety in AGE to the copolymerization, and the consequent introduction of the carbon–carbon double bond into the side chain of the polyester, and (3) arrangement of the sequentially ordered two orthogonal reactive groups according to the alternating manner. The introduction of the two reactive groups to the side chain of the alternating copolymer allowed two routes of sequential chemoselective reactions: (A) The ring‐opening reaction of the lactone moiety with n‐propylamine and the following Pt‐catalyzed hydrosilylation of the carbon–carbon double bond with dimethylphenylsilane and (B) the sequential reactions of the reverse order. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2009     

Condensative chain polymerization. II. Preferential esterification of propagating end group in Pd-catalyzed CO-insertion polycondensation of 4-bromophenol derivatives

For a development of condensative chain polymerization where polycondensation proceeds from an initiator in a chain polymerization manner to yield polymer with a defined molecular weight and a narrow molecular weight distribution, the Pd-catalyzed polycondensation of 4-bromophenol derivatives with CO is studied. Model reactions showed that monomer reacted the polymer terminal Br preferentially compared to the monomer Br, but that the ester exchange reaction of polymer backbone with monomer phenoxide occurred in some extent. In the polymerization of 4-bromo-2-n-octylphenol with CO using 4-bromo-2,6-dimethylphenyl benzoate as an initiator, the molecular weight of polymer increased in proportion to time up to 30 min. The GPC elution curves showed that oligomers were produced from the initiator. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2607–2618, 1999     

Application of ketenes to well‐defined polyester synthesis (4): End‐capping reactions in living anionic polymerization of ethylphenylketene

End‐capping reactions of a living polyester, obtained by anionic polymerization of ethylphenylketene (EPK), were carried out. As end‐capping reagents, electrophiles such as alkyl halide and acyl halide were successfully used. Reactivity of the terminal enolate and the resulting terminal structures were elucidated by model reactions, using lithium enolates having low molecular weights, obtained by an equimolar reaction of EPK with butyllithium. Polymerization of EPK by lithium alkoxide and the subsequent end‐capping reaction afforded the corresponding polyester having functional groups at both chain ends and a narrow molecular weight distribution. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3103–3111, 2002     

Block copolymers of telechelic poly(phenylene sulfide) and semiaromatic thermotropic liquid crystalline polyester segments

We report the synthesis and characterization of copolymers comprising poly(phenyl sulfide) (PPS) blocks and semiaromatic thermotropic liquid crystalline polymer (TLCP) blocks. The copolymers, synthesized by melt-transesterification of dicarboxy-terminated poly(phenylene sulfide) with poly(ethylene terephthalate-co-oxybenzoate) (PET/OB), were characterized using Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), X-ray diffraction (XRD), and polarized light optical microscopy (PLOM). The crystallizability and liquid crystalline properties of the copolymers are greatly influenced by the extent of interchange reactions, the mole percent of oxybenzoate with respect to the PET, the PPS : PET/OB weight ratio, and the reaction time. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 2707–2713, 1998     

Mechanistic discussion of cationic crosslinking copolymerizations of 1,2‐epoxycyclohexane with diepoxide crosslinkers accompanied by intramolecular and intermolecular chain transfer reactions

Our previous mechanistic discussion of the free‐radical crosslinking monoallyl/diallyl copolymerizations was extended to the cationic crosslinking monoepoxide/diepoxide copolymerizations, typically including 1,2‐epoxycyclohexane (ECH) as a monoepoxide and bis[3,4‐epoxycyclohexylmethyl] adipate (BECHMA) as a diepoxide crosslinker. In the cationic polymerization, oligomer is usually obtained because of the occurrence of characteristic chain‐forming reactions. Therefore, cationic crosslinking monoepoxide/diepoxide copolymerizations could be in the category of the network formation through free‐radical crosslinking monoallyl/diallyl copolymerizations. Thus, the gelation behavior was discussed by comparing the actual gel points with the theoretical ones; the greatly delayed gelation from theory was observed. Then, the resulting network polymer precursors (NPPs) were characterized by SEC‐MALLS‐viscometry to clarify the cationic crosslinking ECH/BECHMA copolymerization mechanism. Notably, the correlation lines of molecular weight versus elution volume were specific for the NPPs obtained at a high conversion close to the gel point as compared with those obtained by the free‐radical crosslinking monoallyl/diallyl copolymerization. This may be ascribed to the occurrence of intramolecular and intermolecular chain transfer reactions characteristic of cationic polymerization; the chain transfer reactions involve the intramolecular and intermolecular nucleophilic attack of ether oxygen or terminal hydroxyl oxygen in the NPPs to a terminal growing cation that leads to the formation of not only the loop‐ but also the crosslink‐structures containing NPPs, providing fragile ultrahigh‐molecular‐weight NPP in the SEC columns. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis of biodegradable copolymers with low‐toxicity zirconium compounds. V. Multiblock and random copolymers of L‐lactide with trimethylene carbonate obtained in copolymerizations initiated with zirconium(IV) acetylacetonate

Using zirconium(IV) acetylacetonate as an initiator of lactide/trimethylene carbonate copolymerization allowed us to obtain high‐molecular‐weight copolymers with high efficiency. The reactivity ratios of the comonomers were 13.0 for lactide and 0.53 for trimethylene carbonate. Despite the large differences between the values of the reactivity ratios, copolymers with randomized chain structures were obtained. This phenomenon occurred as a result of an intensive intermolecular transesterification process proceeding along with the reaction of copolymer chain growth and modifying its final structure. Conducting the copolymerization at the relatively low temperature of about 110 °C, which minimized the influence of intermolecular transesterification, made it possible to obtain semicrystalline copolymers with multiblock structures. Increasing the temperature of copolymerization up to 180 °C was associated with strong intensification of the transesterification reactions. At this temperature, amorphous copolymers were obtained with identical compositions but highly randomized chain structures. An analysis of the chain microstructures of the obtained copolymers, determining the average length of the blocks, the intermolecular transesterification ratio, and the degree of chain randomization, was conducted by means of NMR spectroscopy. For this purpose, very specific signal assignment in the carbonyl and methylene carbon regions of the ¹³C NMR spectra to appropriate comonomer sequences of polymeric chains was performed. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3184–3201, 2006     

Isospecific copolymerization of styrene and a styrene‐terminated polyisoprene macromonomer with the Ni(acac)2/MAO catalyst

The copolymerization of styrene (St) with a styrene‐terminated polyisoprene macromonomer (SIPM) by a nickel(II) acetylacetonate [Ni(acac)₂] catalyst in combination with methylaluminoxane (MAO) was investigated. A SIPM with a high terminal degree of functionalization and a narrow molecular weight distribution was used for the copolymerization of St. The copolymerization proceeded easily to give a high molecular weight graft copolymer. After fractionation of the resulting copolymer with methyl ethyl ketone, the insoluble part had highly isotactic polystyrene in the main chain and polyisoprene in the side chain. Lowering the MAO/Ni molar ratio and the polymerization temperature were favorable to producing isospecific active sites. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1241–1246, 2000