Comparison of glass transition and interpretation on miscibility in blends of amorphous poly(vinyl methyl ether) with highly crystallizable versus less‐crystallizable polyesters

Various phase behavior of blends of poly(vinyl ether)s with polyesters of two types (highly crystalline and less crystalline with different main‐chains) were examined using differential scanning calorimetry (DSC) and optical microscopy (OM). Effects of varying the main‐chain polarity of the constituent polyesters on the phase behavior of the blends were analyzed. Miscibility in PVME/polyester blends was found only in polyesters with backbone CH₂/CO ratio = 3.5 to 7.0). T_g‐composition relationships for blends of PVME with highly crystalline polyesters (PBA, PHS) were found to differ significantly from those for PVME blends with less‐crystalline polyesters (PTA, PEAz). Crystallinity of highly crystalline polyester constituents in blends caused significant asymmetry in the T_g‐composition relationships, and induced positive deviation of blends' T_g above linearity; on the other hand, blends of PVME with less crystalline polyesters exhibit typical Fox or Gordon‐Taylor types of relationships. The χ parameters for the miscible blends were found to range from ?0.17 to ?0.33, reflecting generally weak interactions. Phase behavior was analyzed and compared among blends of PVME with rapidly crystallizing vs. less‐crystallizing polyesters, respectively. Effects of polyesters' crystallinity and structures on phase behavior of PVME/polyester blends are discussed. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2899–2911, 2007     

Preparation and use of diacetylene-containing polyesters for studying deformation micromechanics in model polyester-polyolefin blends

A range of diacetylene-containing polyesters have been prepared by polycondensation of terephthaloyl chloride with diacetylene diols of structure HO—(CH₂)_n—C≡C—C≡C—(CH₂)_n—OH, where n = 1, 2, 3, 4 and 9. The results from characterization of the polyesters by DSC and Raman spectroscopy are presented. The polyesters from the diols with n = 3 and n = 9 have melting points (T_m) of 186 and 88 °C, respectively, and cross-polymerise under irradiation, but not thermally. These polyesters were blended with isotactic polypropylene (T_m = 167 °C) and the blends compression-moulded into dumbbell specimens, which then were exposed to ⁶⁰Co γ-radiation to effect cross-polymerization of the polyester phases. The dumbbell specimens were subjected to simultaneous tensile testing and resonance Raman spectroscopy, and the shift in wavenumber of the C≡C stretching band of the polydiacetylene crosslinks used to determine the local stress in the polyester phases independent of the overall applied stress, thereby facilitating determination of the efficiency of stress transfer in the blends.     

Miscible blends prepared from two crystalline polymers

Differential scanning calorimetry was used to determine the miscibility behavior of several polyester/Saran blends, the two polymers forming these blends being semicrystalline. It was found that Saran is miscible with polycaprolactone (PCL), polyvalerolactone, poly(butylene adipate), and poly(hexamethylene sebacate) since a single glass transition temperature T_g was observed at each composition. However, immiscibility was found between Saran and poly(ethylene adipate), poly-(ethylene succinate), poly(β-propiolactone), and poly(α-methyl-α-n-propyl-β-propiolactone) since two T_g's were recorded at several compositions. Blends were then obtained containing, over a wide range of composition, a miscible amorphous phase and two different types of crystals. From melting-point depression data on PCL and Saran crystals, thermodynamic interaction parameters χ were calculated and found to be different for PCL-rich blends and for Saran-rich blends. This result suggests a variation of χ with composition. Saran is a polymer which does not contain α-hydrogens and its miscibility with polyesters may result from a β-hydrogen bonding interaction or a C?O/C? Cl dipole-dipole interaction.     

Blends of different linear polyamides with hyperbranched aromatic AB2 and A2 + B3 polyesters

To explore the possible applications of hyperbranched polymers for modifying linear polyamides, two hyperbranched aromatic polyesters characterized as high T_g polymers possessing phenolic end groups were used in melt mixing with partly aromatic polyamide and commercially available aliphatic polyamide‐6, respectively. Different amounts of both hyperbranched polyesters (from 1 wt % up to 20 wt %) were added to the polyamides, and the influence of these hyperbranched polyesters on the properties of the polyamides was investigated. The hyperbranched polyester based on an AB₂ approach was found to be the most effective modifier. A significant increase of the glass transition temperature of the final blend was detected. However, a remarkable reduction of crystallinity as well as complex melt viscosity of those blends was also observed. The use of an A₂+B₃ hyperbranched polyester as melt modifier for the polyamides was less effective for changing the thermal properties, and the complex melt viscosity of the final material increased since heterogeneous blends were formed. In contrast to that, generally, the addition of the AB₂ hyperbranched polyester to the polyamides resulted in homogeneous blends with improved T_g and processability. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3558–3572, 2009     

Vapor phase deposition of polybenzoxazoles

Vapor phase deposition was carried out on multifunctional aliphatic and aromatic benzoxazoles to yield powdered samples of poly(dimethylenebenzoxazoles). Representative aliphatic and aromatic poly(dimethylenebenzoxazoles) were also synthesized through solution methods using 4-amino-3-hydroxyhydrocinnamic acid and 2-(4-(bromomethyl)phenyl)-6-(bromomethyl)benzoxazole, respectively, as monomers. Both aromatic and aliphatic polybenzoxazoles containing  CH₂CH₂ units in the polymer backbone displayed catastrophic weight loss over a very narrow temperature range. This is in contrast with other polybenzoxazoles which show a gradual weight loss over 500–1000°C. Vapor phase deposition carried out under vacuum on the polymers gave similar polymers in the collection zone suggesting the catastrophic weight loss is attributed to thermal depolymerization of the polymer through a diradical intermediate similar to the thermolysis and polymerization of [2.2]paracyclophane. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1317–1328, 1998     

Complete miscibility of ternary aryl polyesters demonstrating a new criterion and horizon for miscibility characterization

A ternary miscible blend system comprising only crystallizable aryl polyesters [poly(ethylene terephthalate), poly(trimethylene terephthalate), and poly(butylene terephthalate)] was characterized with the criteria of thermal analyses, microscopy, and X‐ray characterizations. The reported ternary miscibility (in the quenched amorphous state of blends of the three aryl polyesters) was truly physical and under the condition of no chemical transesterifications; this justified that transesterification was not a necessary condition for miscibility in polyester blends in this case. This study further proposed and tested a novel concept of a new criterion for miscibility characterization for polymer blends of only crystallizable polymers. A single composition‐dependent cold‐crystallization‐temperature (T_cc) peak in blends of only semicrystalline polymers was taken as an indication of an intimate mixing state of miscibility. The theoretical background for establishing the single composition‐dependent T_cc peak as a valid miscibility criterion for crystallizable polymer blends was examined. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2394–2404, 2003     

Determination of interactions between aryl polyesters and poly(ether imide) via glass transition temperatures of separated phases in immiscible blends

Phase behavior in domains of immiscible blends of poly(pentamethylene terephthalate)/poly(ether imide) (PPT/PEI) and poly(hexamethylene terephthalate)/poly(ether imide) (PHT/PEI) were investigated using differential scanning calorimetry (DSC). The measured glass transition temperature (T _g) reveals that aryl polyesters dissolve more in the PEI-rich phase than the PEI does in the aryl polyester-rich phase, for both PPT/PEI and PHT/PEI systems. Additionally, optical microscopy supports the conclusion that PPT (or PHT) dissolves more in the PEI-rich phase than PEI does in the PPT-rich (or PHT-rich) phase in the aryl polyester/PEI blends. Furthermore, the Flory–Huggins interaction parameters (χ₁₂) for the PPT/PEI and the PHT/PEI blends were calculated to be 0.12 and 0.17, respectively. For the blend systems comprising of PEI and homologous aryl polyesters, the value of χ₁₂ exhibits a trend of variation with respect to structure of aryl polyesters. For the PPT/PEI and PHT/PEI blends, investigated in this study, value of the polymer–polymer interaction parameter (χ₁₂) between the aryl polyester and the PEI was found to be positive, which increases with the number of methylene moieties in the repeating unit of the aryl polyester, ultimately resulting in phase separation observed.     

Solid-State 13C-NMR detection of the isotropic carbonyl line shape in blends of poly(vinylphenol) with main-chain polyesters

The solid-state NMR isotropic line shape of the carbonyl ¹³C resonance is useful as a qualitative diagnostic probe of the polyester component′s morphology and molecular mobility in partially miscible blends with poly(vinylphenol), PVPh. The main-chain polyesters chosen for investigation in this study are poly(ethylene succinate), poly(ethylene adipate), poly(butylene adipate), and poly(caprolactone). A crystalline phase exists for polyester-rich mixtures in all cases. Verification of this claim is provided by DSC endothermic tran-sitions that map out melting point depression in the temperature-composition phase dia-grams. The carbonyl ¹³C-NMR signal in the crystalline domains exhibits a full width at half height of 1–2 ppm when the glass transition temperature of the blends is below the temperature of the NMR experiment. In all cases, a single concentration-dependent glass-transition temperature is measured by DSC, which increases monotonically from below ambient for polyester-rich blends to well above ambient for blends that are rich in poly(vinylphenol). When the concentration of the amorphous proton donor PVPh is suf-ficient to thwart crystallization of the polyester and increase the glass transition temperature of the blends above the temperature of the NMR experiment, the line width of the carbonyl resonance increases three- to fourfold to ca. 5–6 ppm. When the blends are completely amorphous and T_g is above ambient, the polyester carbonyl ¹³C line shape reveals at least two morphologically inequivalent microenvironments. A partially resolved carbonyl signal in rigid amorphous blends is (a) identified at higher chemical shift relative to the crystalline component, and (b) attributed to hydrogen bonding in the amorphous phase. This inter-action-sensitive hydrogen-bonded carbonyl signal accounts for an increasing fraction of the overall NMR absorption envelope of the carbonyl carbon site when the polyester is saturated with PVPh. The main-chain polyesters were chosen to probe the effect of chemical structure of the proton acceptor on the potential for hydrogen-bond formation. Aliphatic CH₂ spacers between the carbonyl groups dilute the concentration of interacting sites, and the dependence of the carbonyl ¹³C-NMR line shape on blend concentration reveals unique spectroscopic behavior in each of the four blend systems investigated. © 1993 John Wiley & Sons, Inc.     

Miscibility of polyester/nitrocellulose blends: A DSC and FTIR study

The miscibility of polyester/nitrocellulose blends was investigated by differential scanning calorimetry and Fourier-transform infrared (FTIR) spectroscopy. Two nitrocelluloses (NC) derived from wood and having different nitrogen contents (12.62 and 13.42%) were used. On the basis of the glass transition temperature criterion, poly(?-caprolactone) (PCL), poly(valerolactone), poly(ethylene adipate), and poly(butylene adipate) are miscible with nitrocellulose, whereas poly(α-methyl α-propyl β-propiolactone) and poly(α-methyl β-proiolactone) are immiscible. The T_g versus composition curves of PCL/NC blends do not follow a monotone function but exhibit a singular point at a critical PCL volume fraction of 0.51 for NC-1342 and 0.45 for NC-1262 in agreement with Kovacs' theory. A shift of 17 cm^-1 of the carbonyl stretching band was observed with PCL/NC blends and is taken as evidence for hydrogen bonding interaction between the PCL carbonyl group and NC hydroxyl group. The frequency difference between the free hydroxyl absorbance and the absorbances of the hydrogen-bonded species was found to be 85 cm^-1 in pure NC and 125 cm^-1 in PCL/NC blends; it indicates that the average strength of this interaction is stronger than the corresponding self-associated hydrogen bonding in pure NC. The presence of a dipole-dipole interaction between the nitrate-ester groups of NC and the carbonyl groups of the polyesters is reported. The relative strength of the hydrogen bonding and dipole-dipole interactions is discussed and correlated with polymer miscibility.     

Thermodynamic study of poly(vinyl chloride)/polyester blends by inverse-phase gas chromatography at 120°C

Polymer/polymer interaction parameters χ′₂₃ have been measured at 120°C as a function of polymer concentration for six different poly(vinyl chloride)/linear aliphatic polyester blends. The technique used is inverse-phase gas chromatography with several molecular probes. The polymers investigated are poly(DL-lactide), poly(ethylene succinate), poly(ethylene adipate), poly(butylene adipate), poly(δ-valerolactone), poly(ε-caprolactone) and poly(hexamethylene sebacate). Probe/polymer interaction parameters χ₁₂ and polymer/polymer interaction parameters χ′₂₃ values are dependent upon the methylene to carbonyl ratio of the polyester, reaching a minimum for a value of 5, this ratio corresponding to poly(ε-caprolactone) blends. Results are interpreted in terms of pairwise interactions between carbonyl, methylene, and [CHCl] groups.     

Gas transport properties of a series of high Tg polynorbornenes with aliphatic pendant groups

A study of gas transport properties of novel polynorbornenes with increasing length of an aliphatic pendant group R (CH₃ , CH₃(CH₂)₃ , CH₃(CH₂)₅ , CH₃(CH₂)₉ ) has been performed. These polymers were synthesized using novel organometallic complex catalysts via an addition polymerization route. This reaction route maintained the bridged norbornene ring structure in the final polymer backbone. Gas permeability and glass transition temperature were found to be higher than those for polynorbornenes prepared by ring-opening metathesis and reported in the literature. It was shown that for noncondensable gases such as H₂ and He the selectivity over N₂ decreased when the length of the pendant group increased, but remained relatively stable for the more condensable gases (O₂ and CO₂). The permeability coefficient is correlated well to the inverse of the fractional free volume of the polymers. The more condensable gases showed a deviation from this correlation for the longest pendant group, probably due to an increase of the solubility effect. This polymer series demonstrated a simultaneous increase in permeability and selectivity, uncommon for polymers. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 797–803, 1998     

Ru and Sm catalyzed polyaddition of dialdehydes to give polyesters. Application of Tishchenko type reactions to polymer synthesis

RuH₂(PPh₃)₄ catalyzed Tishchenko type polyaddition of terephthal-aldehyde gives aromatic polyester ( 1 ), which contains three structural units, [OCH₂ C₆H₄ CH₂O] ( 1a ), [OCH₂ C₆H₄ CO] ( 1b ), and [CO C₆H₄ CO] ( 1c ). ¹H-NMR spectrum shows the presence of the three units in a 1 : 2 : 1 ratio. Isophthalaldehyde also undergoes similar polyaddition to give another aromatic polyester ( 2 ), while 1,12-dodecanedial gives an aliphatic polyester ( 3 ) containing the following structural units: [OCH₂ (CH₂)₁₀ CH₂O] ( 3a ), [OCH₂ (CH₂)₁₀ CO] ( 3b ), and [CO (CH₂)₁₀ CO] ( 3c ). The above polymers have M_n of 2.7 × 10³−5.4 × 10³ and M_w of 4.3 × 10³ − 9.7 × 10³, respectively. Mixtures of terephthalaldehyde and 1,12-dodecanedial produce copolymers, which contain the units 1a–1c and 3a–3c in a random sequence. In the copolymerization, terephthalaldehyde shows a strong tendency to give 1c units, whereas 1,12-dodecanedial predominantly affords 3a units. SmI₂ also catalyzes polyaddition of terephthalaldehyde to give the corresponding polyester with M_n of 1.7 × 10³ and M_w of 3.7 × 10³, respectively. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1265–1273, 1997     

Synthesis,characterization, and in vitro antimicrobial and antitumor activities of some tetraphenylstibonium(V) carboxylates

Several hitherto unreported pentacoordinated tetraphenylstibonium(V) carboxylates of general formula (C₆H₅)₄SbL, where L = o‐OHC₆H₅COO , (C₆H₅)₂C(OH)COO , 2‐(6‐OCH₃C₁₀H₆)CH(CH₃)COO , ArCH(OH)COO (Ar = C₆H₅, p‐CF₃C₆H₄, and p OCH₃C₆H₄), have been prepared and characterized by elemental analysis, solid state IR, ¹H NMR, and ¹³C NMR spectra, conductivity, and molecular weight measurements. Spectroscopic data together with solution phase studies conform to the requirement of triagonal‐bipyramidal configuration for these compounds. They were tested for in vitro antifungal (against Aspergillus flavus and Aspergillus niger) and antibacterial (against Staphylococcus aureus and Klebsiella pneumoniae) activities. The in vitro antitumor activity of all stibonium carboxylates was examined against MCF‐7 cell line. A few of them were found to exhibit moderate to significant biological activity. © 2008 Wiley Periodicals, Inc. Heteroatom Chem 19:688–693, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/hc.20498     

Miscible blends of amorphous polymers

Thirty-five polymethacrylate/chlorinated polymer blends were investigated by differential scanning calorimetry. Poly(ethyl), poly(n-propyl), poly(n-butyl), and poly(n-amyl methacrylate)s were found to be miscible with poly(vinyl chloride) (PVC), chlorinated PVC, and Saran, but immiscible with a chlorinated polyethylene containing 48% chlorine. Poly(methyl) (PMMA), poly(n-hexyl) (PHMA), and poly(n-lauryl methacrylate)s were found to be immiscible with the same chlorinated polymers, except the PMMA/PVC, PMMA/Saran, and PHMA/Saran blends, which were miscible. A high chlorine content of the chlorinated polymer and an optimum CH₂/COO ratio of the polymethacrylate are required to obtain miscibility. However, poly(methyl), poly(ethyl), poly(n-butyl), and poly(n-octadecyl acrylate)s were found to be immiscible with the same chlorinated polymers, except with Saran, indicating a much greater miscibility of the polymethacrylates with the chlorinated polymers as compared with the polyacrylates.     

Supramolecular hexagonal structure of a segmented liquid crystalline polyester with allyl group as lateral substituent

The molecular structure of the phase—stable at room temperature—for the polymer with formula [ p C₆H₄ COO p C₆H₃(R) p C₆H₃(R) OOC p C₆H₄ O (CH₂)₁₀O ]_x, with R =  CH₂ CHCH₂, is reported. The cell is hexagonal (a = b = 13.43 Å, c = 33.3 Å, γ = 120°), space group P6₃, six chains per unit cell (d_calcd = 1.23 g cm⁻³). The six chains are packed together to give a bundle with the center of mass set at the origin of the unit cell. The allyl groups are placed inside the bundle, thus explaining the unexpected reactivity of the double bonds to give crosslinking when fiber samples are annealed in the solid state. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1601–1607, 1999     

Thermosetting polymer blends of unsaturated polyester resin and poly(ethylene oxide). I. Miscibility and thermal properties

The miscibility and thermal properties of polyethylene oxide(PEO)/oligoester resin (OER) blends and PEO/crosslinked polyester (PER) blends were studied by differential scanning calorimetry (DSC). The effect of quenching process on the crystallization behavior of PEO for these two systems were investigated and discussed in details. It has been found that a single, composition dependent glass transition temperature (T_g) was observed for all the blends, indicating that the two systems are miscible in the amorphous state at overall compositions. From the melting point depression of PEO, the interaction parameter χ₁₂ for PEO/OER blends and that for PEO/PER blends were found to be −1.29 and −2.01, respectively. The negative values of χ₁₂ confirmed that both PEO/OER blends and PEO/PER blends are miscible in the molten state. Quenching process has a greater hindrance on the crystallization of PEO/OER blends than on that of PEO/PER blends. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3161–3168, 1997     

Thermal analysis on phase behavior of poly(<Emphasis Type="SmallCaps">l</Emphasis>-lactic acid) interacting with aliphatic polyesters

Abstract  

Thermal behavior, miscibility, and crystalline morphology in blends of low-molecular-weight poly(l-lactic acid) (LM_w-PLLA) or high-molecular-weight PLLA (HM_w-PLLA) with various polyesters such as poly(butylene adipate) (PBA), poly(ethylene adipate) (PEA), poly(trimethylene adipate) (PTA), or poly(ethylene succinate) (PESu), respectively, were explored using differential scanning calorimeter (DSC), and polarized-light optical microscopy (POM). Phase behavior in blends of PLLA with other polyesters has been intriguing and not straight forward. Using a low- and high molecular weight PLLA, this study aimed at mainly using thermal analyses for probing the phase behavior, phase diagrams, and temperature dependence of blends systems composed of PLLA of two different molecular weights (low and high) with a series of aliphatic polyesters of different structures varying in the (CH₂/CO) ratio in main chains. The blends of LM_w-PLLA/PEA and LM_w-PLLA/PTA show miscibility in melt and amorphous glassy states. Meanwhile, the LM_w-PLLA/PESu blend is immiscible with an asymmetry-shaped upper critical solution temperature (UCST) at 220–240 °C depending on the blend composition. In contrast to miscibility in LM_w-PLLA/PTA and LM_w-PLLA/PEA blends, HM_w-PLLA with polyesters are mostly immiscible; and HM_w-PLLA/PTA blend is the only one showing an asymmetry-shaped UCST phase diagram with clarity points at 195–235 °C (depending on composition). Reversibility of UCST behavior, with no chemical transreactions, in these blends was proven by solvent recasting, gel permeation chromatography, and Fourier transform infrared spectroscopy (FT-IR). Crystalline morphology behavior of the LM_w-PLLA/PEA and LM_w-PLLA/PTA blends furnishes addition evidence for miscibility in the amorphous phase between LM_w-PLLA and PTA or PEA.     

Linear polyesters containing isocyanurate rings

Two series of linear polyesters containing isocyanurate rings have been prepared to determine the effect of structural variations on thermal and solubility properties. The polyesters were prepared by the polycondensation reaction of isocyanurate containing difunctional acid and ester monomers with linear diols. The substituent on the isocyanurate ring and the length of the acid side chain have been shown to have considerable effect on the glass transition temperature T_g. Different solubility properties were observed for the series of polyesters in which the pendant substituent was ? C₆H₅ and the acid side-chain was ? CH₂CO₂H. These polymers were insoluble in THF, and the polyester prepared from 1,6-hexanediol was also insoluble in chloroform. Thermal gravimetric analysis (TGA) indicated that structural differences had no significant effect on the thermal stability of these linear polyesters.