Electron microscopy methods for studying polymer blends—comparison of scanning electron microscopy and transmission electron microscopy

The possibility of using a scanning electron microscope (SEM) for studying the morphology of mechanical polymer blends was investigated. Compounds of SBS/EPDM, and both filled and unfilled NBR/EPDM were tested. OsO₄-stained thin-sections were also examined in a transmission electron microscope (TEM) and the results were compared.It seemed to be quite possible to use atomic number contrast detection in combination with OsO₄ staining for visualizing the morphology of the blends in SEM. Domains as small as 0·1 μm were clearly seen. This was done by means of a Robinson backscattered electron detector. Sample preparation was easy, 2 mm thick rubber plates were cut on dry ice to obtain a smooth surface. After staining, the samples were coated with a thin conductive carbon layer.The inner structures of SBS and the carbon black particles were not resolved in SEM but were easily seen in TEM.     

X-ray microanalysis and high-resolution transmission electron microscopy of the reduced titanium-niobium oxides

Phase relationships in TiNb₂O₇ and Ti₂Nb₁₀O₂₉ reductions at 1400°C were investigated by means of X-ray microanalytical electron microscopy and high-resolution transmission electron microscopy (TEM). Compositions of phases present in equilibrium were obtained by applying thin-crystal approximation by which $\text{Nb}\text{Ti}$ ratios in different phases were determined; their oxygen content was inferred from structural considerations. In this manner, phase relationships in that portion of the TiO₂NbO₂NbO_2.5 equilibrium diagram with 2.417 ≥ x (in MeO_x) ≥ 2 were defined. Data obtained, in combination with high-resolution electron microscopy observations, confirmed that the reduction reaction, in part, is a heterogeneous process controlled by outward diffusion of both metal and oxygen atoms. Recombination of the diffused particles leads to the formation of separate crystals. The original block structure phase undergoes transformation in a quasihomogeneous manner either to an isomorphous phase in the binary NbO system or to a structurally related lower composition oxide. A new superstructure Me₂₅O₆₀(Ti_7.16Nb_42.84O₁₂₀) has been detected as an intermediate metastable phase, generated in the reduction of TiNb₂O₇ to stable Me₁₂O₂₉(Ti_1.53Nb_10.47O₂₉) and MeO₂(Ti_0.52Nb_0.48O₂) phases. Consideration of phase relationships among Me₂₅O₆₀, Me₁₂O₂₉, and MeO₂ suggests a chemical mechanism for the reaction concerned. The Me₂₅O₆₀ superstructure has a monoclinic symmetry with cell parameters a = 19.0 Å, b = 3.8 Å, c = 26.6 Å, α = 90°, β = 90°, γ = 78.5°, as determined from the structure image calculations.     

Microstructural characterisation of five simulated archaeological copper alloys using light microscopy, scanning electron microscopy, energy dispersive X-ray microanalysis and secondary ion mass spectrometry

This paper describes the microstructural characterisation of five simulated archaeological copper alloys, produced by modern powder technology. The chemical composition of the examined bronzes covers the major families of archaeological bronzes from antiquity until the Roman period. Light microscopy (LM), energy dispersive X-ray microanalysis (EDX), scanning electron microscopy (SEM) as well as two- and three-dimensional secondary ion mass spectrometry (SIMS) have been used to describe the main properties of the alloys. The results show a heterogeneous microstructure on a micrometer scale, formed by metallic and non-metallic phases. The latter are conglomerates of oxides or sulphides of major or minor elements.     

Application of scanning electrochemical microscopy and scanning electron microscopy for the characterization of carbon-spray modified electrodes

Different gold surfaces modified by carbon-spray have been investigated by scanning electron microscopy (SEM) and scanning electrochemical microscopy (SECM). A transformation of the SECM image to a distance-location profile is proposed which assists the correlation of both images. The structures found in the transformed SECM images of carbon-spray layers on gold substrates can be explained by the topographic features visible in the SEM pictures. Tempering the carbon spray results in an increased density of electrochemically reactive carbon particles which could be confirmed by cyclic voltammetric investigations. Gold minigrids modified with carbon spray expose some areas of especially large currents which could not be predicted from their SEM images. This effect may result from particles located at the edge of a wire intersection having relatively large active surfaces per particle. They contribute significantly to the total current of the minigrid.     

Application of particle-induced X-ray emission, backscattering spectrometry and scanning electron microscopy in the evaluation of orthodontic materials

The focus of this investigation was on orthodontic materials used in the manufacture of dental brackets. The properties of these dental materials are subjected to various physical parameters such as elongation, yield strength and elasticity that justify their application. In turn, these parameters depend on the quantitative elemental concentration distribution (QECD) in the materials used in the manufacture. For compositional analysis, proton-induced X-ray emission (PIXE), backscatter spectrometry (BS) and scanning electron microscopy (SEM) were applied. QECD analysis was performed to correlate the physical parameters with the composition and to quantify imperfections in the materials. PIXE and BS analyses were performed simultaneously with a 3 MeV proton beam while electrons accelerated at 25 keV were used for the SEM analysis. From the QECDs it was observed that: (1) the major elements Cr, Fe and Ni were homogeneously distributed in the orthodontic plate; (2) the distribution of Mo and O correlated with one another; (3) there was a spread of Cr around regions of high C concentration; and, (4) areas of high concentrations of Mo and O corresponded to a decrease in C concentrations. Elemental concentration correlations are shown to indicate the similarities and differences in the ease of formation of phases, based on the tangent of linearity.     

Archaeopolymetallurgical study of materials from an Iberian culture site in Spain by scanning electron microscopy with X-ray microanalysis, chemometrics and image analysis

Archaeometallurgical materials from “La Bastida de Moixent”, a site in Valencia (Spain), from the second Iberian iron age (4th Century B.C.) have been studied using metallographic techniques, microanalysis, chemometrics and image analysis. The materials come from various phases of iron production and cupellation of argentiferous lead to obtain silver. Scanning electron microscopy (SEM) is used to determine the morphological, microstructural and topographic characteristics of the samples. Image analysis was used to obtain a numeric estimate of the main components in these materials. X-ray microanalysis (SEM/EDX) provides qualitative and quantitative information about the elements in the sample. The semiquantitative results have been treated by chemometric tools such as Principal Component Analysis (PCA) to group the different archaeological materials. These analyses provide information on the lead and iron metallurgical processes, such as silver production by cupellation used in the period. Macroscopic and microscopic analyses indicate a high quality, acceptably uniform manufactured product, indicating broad technical skill in the later metallurgical process of transformation and refinement of these materials to obtain ingots and manufactured products to trade.     

X-ray and scanning electron microscopy archaeometric studies of pigments from the Aguada culture, Argentina

X-ray diffraction (XRD) and scanning electron microscopy (SEM) with energy-dispersive system (EDX) were used in order to obtain mineralogical and chemical composition of white and reddish pigments belonging to the Ambato style of “Aguada” culture, found in the archaeological site of Piedras Blancas (Catamarca, Argentina 500–1100 AD). These pigments are associated with different sectors, two of them being related to funerary context. Due the scarce amount of samples available, it was necessary to develop a new methodology for their study. X-ray diffraction spectra were collected using a low background Si sample holder, which allows the study of small sample amounts (a few milligrams). The mineral quantifications were carried out by applying the Rietveld method to the XRD spectra. The major difficulties arose for reddish pigments, since they contain iron-bearing phases, such as ferruginous clays, in which neither the concentration of Fe^{+ 2} relative to Fe^{+ 3} nor the location in the lattice (occupancy factor) is completely known. With the aim of performing quantitative elemental analysis from SEM-EDX spectra, a special sample holder for the small amounts of available samples was developed. Commercial standards were used in the quantification process and the characteristic intensities were corrected for matrix effects. Micrographs and EDX point spectra allowed the characterization of minor phases and particle analysis. The Rietveld method combined with the new procedure for EDX analysis has proven to be a suitable method for routine quantitative analysis of small amounts of archaeological pigments.     

X-ray and scanning electron microscopy archaeometric studies of pigments from the Aguada culture,Argentina

X-ray diffraction (XRD) and scanning electron microscopy (SEM) with energy-dispersive system (EDX) were used in order to obtain mineralogical and chemical composition of white and reddish pigments belonging to the Ambato style of “Aguada” culture, found in the archaeological site of Piedras Blancas (Catamarca, Argentina 500–1100 AD). These pigments are associated with different sectors, two of them being related to funerary context. Due the scarce amount of samples available, it was necessary to develop a new methodology for their study. X-ray diffraction spectra were collected using a low background Si sample holder, which allows the study of small sample amounts (a few milligrams). The mineral quantifications were carried out by applying the Rietveld method to the XRD spectra. The major difficulties arose for reddish pigments, since they contain iron-bearing phases, such as ferruginous clays, in which neither the concentration of Fe^+ 2 relative to Fe^+ 3 nor the location in the lattice (occupancy factor) is completely known. With the aim of performing quantitative elemental analysis from SEM-EDX spectra, a special sample holder for the small amounts of available samples was developed. Commercial standards were used in the quantification process and the characteristic intensities were corrected for matrix effects. Micrographs and EDX point spectra allowed the characterization of minor phases and particle analysis. The Rietveld method combined with the new procedure for EDX analysis has proven to be a suitable method for routine quantitative analysis of small amounts of archaeological pigments.     

Decomposition of tetraalkylammonium thiotungstates characterized by thermoanalysis, mass spectrometry, X-ray diffractometry and scanning electron microscopy

Thermal decomposition reactions of tetraalkylammonium thiotungstates, (R₄N)₂WS₄ (R = methyl to heptyl), were investigated with DSC and DTA-TG coupled with mass spectroscopy (MS). The results demonstrate that the complexity of thermal decomposition reactions is significantly influenced by the alkyl group, i.e., more complex steps are observed for the materials with longer alkyl chain lengths. Tetraethyl and tetrapropyl complexes show reversible and irreversible phase transitions detected by DSC experiments combined with thermodiffractometry. The tetrapentyl compound undergoes an irreversible phase transition while the tetraheptyl sample exhibits a glass-like transition and melting prior to decomposition. The whole series of compounds decompose without forming sulfur rich WS_n (n = 3 or 4) intermediates. The final WS₂ products are nearly stoichiometric for R = methyl to pentyl but for hexyl and heptyl samples the sulfur content is significantly reduced with a W/S ratio of about 1.5. The residual carbon and hydrogen contents increase in the final decomposition products in the same order as the number of C atoms in R₄N increase. For the N content no clear trend is obvious. A general thermal decomposition mechanism is suggested which follows a bimolecular nucleophilic substitution reaction. In the SEM images only for R = heptyl the formation of macro-pores with a sponge-like morphology is seen, but for the other precursors compact materials are formed which in part display a well developed morphology. X-ray diffraction analysis of the final products shows the formation of amorphous WS₂ up to the tetrapentyl precursor. But for the tetrahexyl and tetraheptyl materials the W:S ratio is significantly smaller than 1:2 and large amounts of C and H are determined by chemical analyses. In accordance with previously reported results it can be assumed that a carbosulfide phase is formed by a mixed C-W-S sandwich layered structure.     

Analysis of a Nd: YAG laser crystal by X-ray fluorescence,scanning electron microscopy and neutron activation analysis

Recently excavated roman amphorae were submitted to instrumental neutron activation analysis for the determination of Ca, Sc, Cr, Fe, Co, Sb, Ba, La, Ce, Eu, Yb, Lu, Hf and Th. Data reduction was carried out by identifying first the elements useful for discrimination purposes and then by submitting the data to cluster analysis. Amphorae are parted in two groups which are related to different provenance areas.     

Characterization of municipal solid waste incineration (MSWI) bottom ash by scanning electron microscopy and quantitative energy dispersive X-ray microanalysis (SEM/EDX)

Scanning electron microscopy (SEM) with energy-dispersive X-ray microanalysis (EDX) is frequently used for morphological and qualitative chemical characterization of different materials. The applicability of this method for phase identification, is, however, often underestimated. The application of SEM/EDX for the characterization of different phases in fresh and altered municipal-waste incinerator bottom-ash samples with high lateral resolution is presented. Polished thin sections were prepared from the samples, but fresh fracture surfaces were also used. The EDX analyses were performed by using the correction procedures of a conventional standardless ZAF correction, a peak-to-background ZAF correction, and a correction method for light-element analysis. Because of their highly reactive properties the bottom-ash SEM samples require a special method of preparation. The method facilitates nondestructive preparation of the sensitive bottom-ash alteration phases (e.g. cement phases, hydroxides, salts) and their microstructures.     

Characterization of municipal solid waste incineration (MSWI) bottom ash by scanning electron microscopy and quantitative energy dispersive X-ray microanalysis (SEM/EDX)

Scanning electron microscopy (SEM) with energy-dispersive X-ray microanalysis (EDX) is frequently used for morphological and qualitative chemical characterization of different materials. The applicability of this method for phase identification, is, however, often underestimated. The application of SEM/EDX for the characterization of different phases in fresh and altered municipal-waste incinerator bottom-ash samples with high lateral resolution is presented. Polished thin sections were prepared from the samples, but fresh fracture surfaces were also used. The EDX analyses were performed by using the correction procedures of a conventional standardless ZAF correction, a peak-to-background ZAF correction, and a correction method for light-element analysis. Because of their highly reactive properties the bottom-ash SEM samples require a special method of preparation. The method facilitates nondestructive preparation of the sensitive bottom-ash alteration phases (e.g. cement phases, hydroxides, salts) and their microstructures. Received: 18 August 2000 / Revised: 8 November 2000 / Accepted: 12 November 2000     

Morphological and crystalline studies of isotactic polypropylene plastically deformed and evaluated by small-angle X-ray scattering, scanning electron microscopy and X-ray diffraction

Morphological and structural properties of isotactic polypropylene (i-PP) submitted to uniaxial plane strain deformation at ambient temperature with compression pressures of 3, 10 and 20 MPa, were investigated using wide angle X-ray diffraction (WAXD), small-angle X-ray scattering (SAXS), transmission electron microscopy (TEM) and scanning electron microscopy (SEM). Two kinds of samples were studied, namely: sample A: Mw = 117,400 g/mol Mn = 17,300, Mw/Mn = 6.8 and sample B: Mw = 271,000 g/mol Mn = 43,700 Mw/Mn = 6.2, both with isotactic content = 95%. Crystalline α- and β-phases are clearly identified by WAXD. The lamellar long period, as well as, the crystalline and amorphous lamellar thickness for the non-deformed samples measured by SAXS indicates the presence of a more symmetric spherulitic structure for sample A, while the sample B displays anisotropic scattering. The WAXD study of the apparent relative crystallinity and the orientation of crystallites, revealed that plastic deformation of i-PP by plane-strain compression, leads to preferred orientation of main axis of crystallites at relatively early stage of the deformation process induced a monocrystal texture and an excellent molecular alignment along the FD, in both samples. The SEM evaluation shows that a gradual change occurs in the spherulitic structure and seems to transform gradually and disappear almost for the 37% deformations. The sample with highest deformation shows thin shear bands oriented along the FD-view which originate an appearance of a layered structure. Concomitantly the crystalline lamellae were detected by TEM technique.     

Amyloidosis of Alzheimer's Abeta peptides: solid-state nuclear magnetic resonance, electron paramagnetic resonance, transmission electron microscopy, scanning transmission electron microscopy and atomic force microscopy studies

Aggregation cascade for Alzheimer's amyloid-beta peptides, its relevance to neurotoxicity in the course of Alzheimer's disease and experimental methods useful for these studies are discussed. Details of the solid-phase peptide synthesis and sample preparation procedures for Alzheimer's beta-amyloid fibrils are given. Recent progress in obtaining structural constraints on Abeta-fibrils from solid-state NMR and scanning transmission electron microscopy (STEM) data is discussed. Polymorphism of amyloid fibrils and oligomers of the 'Arctic' mutant of Abeta(1-40) was studied by (1)H,(13)C solid-state NMR, transmission electron microscopy (TEM) and atomic force microscopy (AFM), and a real-time aggregation of different polymorphs of the peptide was observed with the aid of in situ AFM. Recent results on binding of Cu(II) ions and Al-citrate and Al-ATP complexes to amyloid fibrils, as studied by electron paramagnetic resonance (EPR) and solid-state (27)Al NMR techniques, are also presented.     

Electron paramagnetic resonance, scanning electron microscopy with energy dispersion X-ray spectrometry, X-ray powder diffraction, and NMR characterization of iron-rich fired clays

The aim of this study is to clarify the structure of an iron-rich clay and the structural changes involved in the firing process as a preliminary step to get information on ancient ceramic technology. To this purpose, illite-rich clay samples fired at different temperatures were characterized using a multitechnique approach, i.e., by electron paramagnetic resonance, scanning electron microscopy with electron dispersion X-ray spectrometry, X-ray powder diffraction, magic angle spinning and multiple quantum magic angle spinning NMR. During firing, four main reaction processes occur: dehydration, dehydroxylation, structural breakdown, and recrystallization. When the results are combined from all characterization methods, the following conclusions could be obtained. Interlayer H2O is located close to aluminum in octahedral sites and is driven off at temperatures lower than 600 degrees C. Between 600 and 700 degrees C dehydroxylation occurs whereas, between 800 and 900 degrees C, the aluminum in octahedral sites disappears, due to the breakdown of the illite structure, and all iron present is oxidized to Fe3+. In samples fired at 1000 and 1100 degrees C iron clustering was observed as well as large single crystals of iron with the occurrence of ferro- or ferrimagnetic effects. Below 900 degrees C the aluminum in octahedral sites presents a continuous distribution of chemical shift, suggesting the presence of slightly distorted sites. Finally, over the whole temperature range, the presence of at least two tetrahedral aluminum sites was revealed, characterized by different values of the quadrupolar coupling constant.     

Equilibrium, FTIR, scanning electron microscopy and small wide angle X-ray scattering studies of chromates adsorption on modified bentonite

The study presents a discussion about the adsorption mechanism of chromate anions on bentonite modified by hexadecyltrimethylammonium bromide (HDTMA-Br). The formation of alkylammonium chromates: HDTMAHCrO₄, (HDTMA)₂Cr₂O₇ and to the lesser extent (HDTMA)₂CrO₄ at the water–bentonite interface is examined based on the Scanning Electron Microscopy and surface tension measurements. The histograms of HDTMA/Cr(VI) molar ratio on the bentonite surface, found from Scanning Electron Microscopy (SEM) measurements, show that for the majority of points of bentonite surface the value of this ratio is in 1–2 range. FTIR spectra of modified bentonite samples show the change from gauche to trans conformation in the surfactant arrangement in the clay interlayer accompanying its concentration increase.

In turn Small Wide Angle X-Ray Scattering (SWAXS) patterns evidently suggest incorporation of chromate anions into the interlamellar space of bentonite structure.     

Ensemble evaluation of polydisperse nanocellulose dimensions: rheology,electron microscopy,X-ray scattering and turbidimetry

Six types of CNCs with different sizes were prepared from tunicins by sulfuric acid hydrolysis and subsequent sonication in water. The size distributions of CNCs were comprehensively evaluated by turbidimetry, small angle X-ray scattering, and microscopy to predict their intrinsic viscosities. Experimental intrinsic viscosities [η] of the CNC dispersions were evaluated by shear viscosity measurement, and then compared with their theoretical [η] values based on theories for rotational motions of rigid rods. The experimental [η] values for the straight CNCs were in good agreement with their theoretical [η] values, irrespective of the size and distributions. On the other hand, the experimental [η] value of the kinked CNC was higher than the theoretical [η] value, in agreement with a theoretical calculation giving higher intrinsic viscosities for bent fibers.     

Information-theoretical feature selection using data obtained by scanning electron microscopy coupled with and energy dispersive X-ray spectrometer for the classification of glass traces

In this work, a selection of the best features for multivariate forensic glass classification using Scanning Electron Microscopy coupled with an Energy Dispersive X-ray spectrometer (SEM-EDX) has been performed. This has been motivated by the fact that the databases available for forensic glass classification are sparse nowadays, and the acquisition of SEM-EDX data is both costly and time-consuming for forensic laboratories. The database used for this work consists of 278 glass objects for which 7 variables, based on their elemental compositions obtained with SEM-EDX, are available. Two categories are considered for the classification task, namely containers and car/building windows, both of them typical in forensic casework. A multivariate model is proposed for the computation of the likelihood ratios. The feature selection process is carried out by means of an exhaustive search, with an Empirical Cross-Entropy (ECE) objective function. The ECE metric takes into account not only the discriminating power of the model in use, but also its calibration, which indicates whether or not the likelihood ratios are interpretable in a probabilistic way. Thus, the proposed model is applied to all the 63 possible univariate, bivariate and trivariate combinations taken from the 7 variables in the database, and its performance is ranked by its ECE. Results show remarkable accuracy of the best variables selected following the proposed procedure for the task of classifying glass fragments into windows (from cars or buildings) or containers, obtaining high (almost perfect) discriminating power and good calibration. This allows the proposed models to be used in casework. We also present an in-depth analysis which reveals the benefits of the proposed ECE metric as an assessment tool for classification models based on likelihood ratios.     

Characterization of particulate matter from the Metropolitan Zone of the Valley of Mexico by scanning electron microscopy and energy dispersive X-ray analysis

Samples of total suspended particles (TSP) and PM10 respirable particles from five monitoring stations from the network system of the Metropolitan Zone of the Valley of Mexico (MZVM) were analyzed by scanning electron microscopy (SEM) and energy-dispersive X-ray microanalysis (EDX). Morphology and chemical composition allowed to identify six groups. The analysis shows that the most abundant groups are Al-Si-O, Fe, and metals, the first one in the TSP fraction. Trace metal, commonly associated to PM10 at a receptor location, will depend on the relative influences of local anthropogenic sources. Metal group was observed in all samples, mainly in Tlalnepantla and CES zones (28–46%).     

Chemical and morphological study of gunshot residue persisting on the shooter by means of scanning electron microscopy and energy dispersive X-ray spectrometry

Persistence of gunshot residue (GSR) simultaneously collected from hands, face and hair, and clothing of the shooting person was examined. Samples were collected from five shooters in nine time intervals after a single shoot with a Luger 9 mm pistol, in the range of 0-4 h and examined with scanning electron microscopy and energy dispersive X-ray spectrometry. Numbers of particles, frequencies of occurrence of certain compositions of particles, and their sizes in function of the time intervals were inspected. The greatest numbers of particles were observed in samples collected from hands right after shooting, but they decrease quickly with time. In samples collected from the face smaller initial numbers of particles were found, but they lasted at a similar level longer. The estimated half-life times of particles were less than 1 h for samples taken from the hands, over 1 h for clothing and about 2-3 h for the face. In samples collected at longer intervals after shooting, there were particles present of small sizes and irregular shapes. The results demonstrate that including evidence collected from the suspect's face and hair may increase the probability of detection of GSR in cases when the suspect has not been apprehended immediately after the investigated incident.