CsPbIBr2钙钛矿太阳能电池中通过氧气诱导Spiro-OMeTAD快速氧化

Spiro-OMeTAD是钙钛矿型太阳能电池中应用最广泛的空穴传输材料,它本身的空穴传输率很低,需要氧化之后才能满足高效率太阳能电池器件的要求.然而,Spiro-OMeTAD在空气中的氧化时间较长,同时空气中的水分会造成器件效率的下降以及器件质量不稳定等不良后果.基于此,我们通过一步法制备CsPbIBr2无机钙钛矿太阳...     

A new strategy for constructing a dispiro-based dopant-free hole-transporting material: spatial configuration of spiro-bifluorene changes from a perpendicular to parallel arrangement

Due to the low intrinsic hole mobility caused by the orthogonal conformation of two fluorene units in Spiro-OMeTAD which is a classic hole-transporting material (HTM) in perovskite solar cells (PSCs), Spiro-OMeTAD based PSCs generally can only obtain high performances through a sophisticated doping process with dopants/additives, which adds to the cost and complicacy of device fabrication, and also adversely affects the stability of PSC devices. Herein, a novel dispiro-based HTM, WH-1, is designed by cleverly replacing the central carbon atom of Spiro-OMeTAD with cyclohexane, and the spatial configuration of the HTM is changed from vertical orthogonality of the two fluorene units to a parallel arrangement, which is beneficial for the formation of a homogeneous and compact HTM film on the surface of the perovskite film, improvement of intermolecular electronic coupling and intrinsic hole mobility. WH-1 is obtained by two-step facile synthesis with a high yield from commercially available materials. WH-1 is used in PSCs as a dopant-free HTM, which is the first time that the dispiro-based molecule has been applied as a dopant-free HTM, and a power conversion efficiency (PCE) of 19.57% is obtained, rivaling Li-TFSI/t-BP doped Spiro-OMeTAD in PCE (20.29%), and showing obvious superior long-term stability.

A dispiro-based HTM with a parallel arrangement of two fluorenes was designed by replacing the central carbon atom of Spiro-OMeTAD with cyclohexane. The PCE of a PSC based on dopant-free WH-1 is 19.57%, rivaling that of doped Spiro-OMeTAD (20.29%).     

Iodonium Initiators: Paving the Air-free Oxidation of Spiro-OMeTAD for Efficient and Stable Perovskite Solar Cells

To date, perovskite solar cells (pero-SCs) with doped 2,2′,7,7′-tetrakis(N,N-di-p-methoxyphenylamine)-9,9′-spirobifluorene (Spiro-OMeTAD) hole transporting layers (HTLs) have shown the highest recorded power conversion efficiencies (PCEs). However, their commercialization is still impeded by poor device stability owing to the hygroscopic lithium bis(trifluoromethanesulfonyl)imide and volatile 4-tert-butylpyridine dopants as well as time-consuming oxidation in air. In this study, we explored a series of single-component iodonium initiators with strong oxidability and different electron delocalization properties to precisely manipulate the oxidation states of Spiro-OMeTAD without air assistance, and the oxidation mechanism was clearly understood. Iodine (III) in the diphenyliodonium cation (IP⁺) can accept a single electron from Spiro-OMeTAD and forms Spiro-OMeTAD⋅⁺ owing to its strong oxidability. Moreover, because of the coordination of the strongly delocalized TFSI⁻ with Spiro-OMeTAD⋅⁺ in a stable radical complex, the resulting hole mobility was 30 times higher than that of pristine Spiro-OMeTAD. In addition, the IP-TFSI initiator facilitated the growth of a homogeneous and pinhole-free Spiro-OMeTAD film. The pero-SCs based on this oxidizing HTL showed excellent efficiencies of 25.16 % (certified: 24.85 % for 0.062-cm²) and 20.71 % for a 15.03-cm² module as well as remarkable overall stability.     

An eco‐friendly water‐soluble fluorene‐based polyelectrolyte as interfacial layer for efficient inverted polymer solar cells

A conjugated polyelectrolyte poly(9,9‐bis(3′‐[(N,N‐dimethyl)‐N‐ethylammonium]‐propyl)‐2,7‐fluorene dibromide) (PFBr) with the feature of environmental friendliness and cheapness was successfully used in polymer solar cells (PSCs) as the cathode interfacial layer (CIL). And we successfully demonstrate that the PFBr can build interfacial dipoles at the CIL/cathode interfaces, leading to reduce cathode work functions and improve open‐circuit voltages, which decrease interfacial energy loss at the cathode. It not only improves the electron transfer efficiency but also inhibits the charge carrier recombination at the contact interface. Impedance spectra revealed that the optimal device with the smallest charge transport time constant of 2.83 microseconds was achieved under the concentration of 2 mg mL⁻¹ of PFBr, which suggests efficient electron transport on the interface between the organic active layer and the indium tin oxide cathode. Moreover, as a consequence, the power conversion efficiency of the PSCs increases to 3.83% (with PFBr as CIL) from 1.89% (without any CIL), based on the poly(3‐hexylthiophene) and [6,6]‐phenyl C₆₁‐butyric acid methyl ester bulk heterojunction active layer. Therefore, our observation can demonstrate PFBr is a prospective candidate as CIL for constructing low‐cost, large‐area, and flexible PSCs.     

Development of electron and hole selective contact materials for perovskite solar cells

Nowadays, both n-i-p and p-i-n perovskite solar cells (PSCs) device structures are reported to give high performance with photo conversion efficiencies (PCEs) above 20%. The efficiency of the PSCs is fundementally determined by the charge selective contact materials. Hence, by introducing proper contact materials with good charge selectivity, one could potentially reduce interfacial charge recombination as well as increase device performance. In the past few years, copious charge selective contact materials have been proposed. Significant improvements in the corresponding devices were observed and the reported PCEs were close to that of classic Spiro-OMeTAD. This mini-review summarizes the state-of-the-art progress of typical electron/hole selective contact materials for efficient perovskite solar cells and an outlook to their development is made.     

Improving the performance of polymer solar cells by efficient optimizing the hole transport layer-graphene oxide

Graphene oxide (GO) materials have emerged as a promising alternative for hole transport layer (HTL) in polymer solar cells (PSCs) due to their unique structures and properties. However, insulating properties and eco-contaminative production of GO still need to be solved. Here, we report on the preparation of GO through an improved Hummers method without using NaNO₃, which is an eco-friendly option because it avoids the emissions of NO₂ and N₂O₄ toxic gases. Subsequently, the GO as HTL in PSCs is reduced by simple heat treatment of different temperatures in air, and the performance of devices is obviously improved. The FT-IR and XPS spectra show oxygenated functional groups in GO thin films are gradually removed with the increase of annealing temperature, which restores sp² hybridized graphitic structure, and makes the GO thin films more conducive to the charge transfer. The highest power conversion efficiency of PSCs based on the P3HT: PC₇₁BM system with GO as HTL is 3.39%, which approaches that of PSCs with PEDOT: PSS as HTL (3.41%). Moreover, the devices with annealed GO as HTL have better stability compared to devices with PEDOT: PSS.     

A mini review: Constructing perovskite p-n homojunction solar cells

Organic metal halide perovskite materials have excellent photoelectric properties, and the power conversion efficiency(PCE) of the perovskite solar cells(PSCs) has increased from 3.8% to more than 25%. In the development of PSCs, innovative architectures were being proposed constantly. However, the use of the electron transport layer(ETL) and hole transport layer(HTL) increases manufacturing costs and process complexity. Perovskite material has ambipolar charge transport characteristics, so it c...     

Dual-Interface Engineering in Perovskite Solar Cells with 2D Carbides

Passivating the interfaces between the perovskite and charge transport layers is crucial for enhancing the power conversion efficiency (PCE) and stability in perovskite solar cells (PSCs). Here we report a dual-interface engineering approach to improving the performance of FA_0.85MA_0.15Pb(I_0.95Br_0.05)₃-based PSCs by incorporating Ti₃C₂Cl_x Nano-MXene and o-TB-GDY nanographdiyne (NanoGDY) into the electron transport layer (ETL)/perovskite and perovskite/ hole transport layer (HTL) interfaces, respectively. The dual-interface passivation simultaneously suppresses non-radiative recombination and promotes carrier extraction by forming the Pb−Cl chemical bond and strong coordination of π-electron conjugation with undercoordinated Pb defects. The resulting perovskite film has an ultralong carrier lifetime exceeding 10 μs and an enlarged crystal size exceeding 2.5 μm. A maximum PCE of 24.86 % is realized, with an open-circuit voltage of 1.20 V. Unencapsulated cells retain 92 % of their initial efficiency after 1464 hours in ambient air and 80 % after 1002 hours of thermal stability test at 85 °C.     

Economical and Environmentally Friendly Organic hydrazone Derivatives Characterized by a Heteroaromatic Core as Potential Hole Transporting Materials in Perovskite Solar Cells

A series of organic electron-rich π-bridged symmetric hydrazones, composed of two donor moieties connected through a thiophene- or a pyrrole-based π-spacer, has been synthesized as a suitable alternative to 2,2’,7,7’-tetrakis[N,N-di(4-methoxyphenyl)amino]-9,9’-spirobifluorene ( Spiro-OMeTAD ), considered the benchmark hole transporting material (HTM) in perovskite solar cells (PSCs). The cheap synthetic protocol is suitable for potential large-scale production. All the compounds were characterized, showing good energy levels alignments with the perovskite and very close energy levels to the Spiro-OMeTAD . Furthermore, computational analysis confirmed the electrochemical trend observed. The costs of synthesis were estimated, as well as the produced waste to synthesise the final HTMs, underlining the low impact of these compounds on the environment with the respect to Spiro-OMeTAD . Overall, the relevant electrochemical properties and the low cost of the synthetic approaches allow these compounds to be a greener and easy-to-synthesize alternative to the Spiro-OMeTAD for industrial development of PSCs.     

A non-wetting and conductive polyethylene dioxothiophene hole transport layer for scalable and flexible perovskite solar cells

The regulated crystallization of perovskite and highly repeatable preparation are decisive challenges for large-scale flexible perovskite solar cells(PSCs). Herein, we synthesize an oil-soluble poly(3,4-ethylenedioxythiophene)(Oil-PEDOT) as a hole transport layer(HTL). The non-wetting Oil-PEDOT HTL can promote the quality of large-area flexible perovskite films because of its optimized crystallinity and printability. The Oil-PEDOT layer also delivers desirable conductivity and charge transport without a complex doping. Consequently, the flexible PSCs with Oil-PEDOT HTL achieve an efficiency of 19.51% and 16.70%based on 1.05 and 22.50 cm~2, respectively. Moreover, these large-scale flexible PSCs demonstrate remarkable mechanical robustness, and the efficiency exhibits 93% retention after 7,000 bending cycles. These results show that the Oil-PEDOT is a potentially efficient HTL for fabricating efficient large-scale flexible PSCs.     

紫外光辐照下CH3NH3PbI3基钙钛矿太阳能电池失效机制

随着光伏产业的不断发展,有机无机杂化钙钛矿太阳能电池的研发成为科学与工业界广泛关注的焦点。到目前为止,其光电转换效率已经提高到了25.2%,成为替代硅基太阳能电池的核心方案之一。然而,钙钛矿太阳能电池的稳定性较差,容易受到环境中氧气、水分、温度甚至光照的影响,这严重制约了其大规模推广与应用。大量科学研究表明,如何避免紫外辐照下有机无机杂化钙钛矿太阳能电池的性能衰减,对于提高钙钛矿太阳能电池的光照稳定性至关重要。然而到目前为止,仍然没有系统的工作来对紫外辐照下钙钛矿太阳能电池性能以及微结构演化过程进行详细的表征与分析。本文中,我们利用聚焦离子束-扫描电子显微分析(FIB-SEM)以及球差校正透射电子显微分析(TEM)等技术,全面地研究了紫外辐照过程中有机无机杂化钙钛矿太阳能电池性能变化规律以及电池微结构演化特征。实验结果表明,紫外辐照过程中太阳能电池内部会形成0.5–0.6 V的内建电场,钙钛矿中的I^-离子在电场的驱动下向金属Au电极和空穴传输层2, 2’, 7, 7’-四[N, N-二(4-甲氧基苯基)氨基]-9, 9'-螺二芴(Spiro-OMeTAD)一侧迁移;随后,空穴传输层与金电极的界面处,碘离子与光生空穴一起与金电极发生反应,将金属态Au氧化成离子态Au⁺。而Au⁺离子则在内建电场的驱动下反向迁移穿过钙钛矿MAPbI₃层,直接被SnO₂和MAPbI₃界面处的电子还原形成金属Au纳米团簇。除此之外,紫外辐照过程中钙钛矿太阳能电池性能降低的同时,往往伴随着Spiro-OMeTAD与钙钛矿界面处物质迁移、钙钛矿薄膜内晶界展宽以及Au纳米颗粒周围MAPbI₃物相分解等现象。以上各种因素的协同作用,共同导致了紫外光照下有机无机杂化钙钛矿太阳能电池光电转换性能(PCE)、开路电压(V_oc)以及短路电流(J_sc)等性能参数的急剧下降。     

Defect and doping concentration study with series and shunt resistance influence on graphene modified perovskite solar cell: A numerical investigation in SCAPS-1D framework

Perovskite solar cells (PSCs) have the potential to be highly efficient, low-cost next-generation solar cells. By raising open circuit voltage (V_oc), the interfacial recombination kinetics can further improve device performance. In this study, we used simulation concept to elucidate the influence of using graphene as a surface passivation material in perovskite solar cells. Graphene works well as an interlayer to promote hole extraction and reduce interfacial recombination. In order to evaluate the effect of graphene in PSCs, the simulation was done in the SCAPS-1D framework to compare the performance of a device with and without graphene. Three interface layers were included to the model: TiO₂/MAPbI₃, MAPbI₃/Graphene, and Graphene/Spiro-OMeTAD, in order to account for the impacts of interface defect density on device performance. The impacts of absorber doping concentration, absorber defect density, ETL doping concentration, HTL doping concentration, series resistance, and shunt resistance were also evaluated for the modelled PSC. Without any optimization, the control device with power conversion efficiency (PCE) of 20.677% was outperformed by the graphene-modified device with PCE of 20.911%. This difference is mostly due to the lower recombination losses and more effective suppression of interfacial non-radiative recombination. With optimization, the modified graphene-based device has a PCE of 26.667%. This result shows an enhancement of ∼1.28 times over that of the pristine graphene-based device. The outcomes have opened the way for the development of cost-effective and comparable state-of-the-art, high-efficiency perovskite solar cells with graphene interlayer by eliminating defects and managing non-radiative recombination.     

Facile Synthesis of a Furan–Arylamine Hole‐Transporting Material for High‐Efficiency,Mesoscopic Perovskite Solar Cells

A novel hole‐transporting molecule (F101) based on a furan core has been synthesized by means of a short, high‐yielding route. When used as the hole‐transporting material (HTM) in mesoporous methylammonium lead halide perovskite solar cells (PSCs) it produced better device performance than the current state‐of‐the‐art HTM 2,2′,7,7′‐tetrakis‐(N,N‐di‐p‐methoxyphenylamine)‐9,9′‐spirobifluorene (spiro‐OMeTAD). The F101‐HTM‐based device exhibited both slightly higher J_sc (19.63 vs. 18.41 mA cm^?2) and V_oc (1.1 vs. 1.05 V) resulting in a marginally higher power conversion efficiency (PCE) (13.1 vs. 13 %). The steady‐state and time‐resolved photoluminescence show that F101 has significant charge extraction ability. The simple molecular structure, short synthesis route with high yield and better performance in devices makes F101 an excellent candidate for replacing the expensive spiro‐OMeTAD as HTM in PSCs.     

Influence of Alkoxy Chain Length on the Properties of Two-Dimensionally Expanded Azulene-Core-Based Hole-Transporting Materials for Efficient Perovskite Solar Cells

A series of two-dimensionally expanded azulene-core-based π systems have been synthesized with different alkyl chain lengths in the alkoxy moieties connected to the partially oxygen-bridged triarylamine skeletons. The thermal, photophysical, and electronic properties of each compound were evaluated to determine the influence of the alkyl chain length on their effectiveness as hole-transporting materials (HTMs) in perovskite solar cells (PSCs). All the synthesized molecules showed promising material properties, including high solubility, the formation of flat and amorphous films, and optimal alignment of energy levels with perovskites. In particular, the derivatives with methyl and n-butyl in the side chains retained amorphous stability up to 233 and 159 °C, respectively. Such short alkoxy chains also resulted in improved electrical device properties. The PSC device fabricated with the HTM with n-butyl side chains showed the best performance with a power conversion efficiency of 18.9 %, which compares favorably with that of spiro-OMeTAD-based PSCs (spiro-OMeTAD=2,2′,7,7′-tetrakis[N,N-bis(p-methoxyphenyl)amino]-9,9′-spirobifluorene).     

Manipulation of the Buried Interface for Robust Formamidinium-based Sn−Pb Perovskite Solar Cells with NiOx Hole-Transport Layers

Low band gap tin-lead perovskite solar cells (Sn−Pb PSCs) are expected to achieve higher efficiencies than Pb-PSCs and regarded as key components of tandem PSCs. However, the realization of high efficiency is challenged by the instability of Sn²⁺ and the imperfections at the charge transfer interfaces. Here, we demonstrate an efficient ideal band gap formamidinium (FA)-based Sn−Pb (FAPb_0.5Sn_0.5I₃) PSC, by manipulating the buried NiO_x/perovskite interface with 4-hydroxyphenethyl ammonium halide (OH-PEAX, X=Cl⁻, Br⁻, or I⁻) interlayer, which exhibits fascinating functions of reducing the surface defects of the NiO_x hole transport layer (HTL), enhancing the perovskite film quality, and improving both the energy level matching and physical contact at the interface. The effects of different halide anions have been elaborated and a 20.53 % efficiency is obtained with OH-PEABr, which is the highest one for FA-based Sn−Pb PSCs using NiO_x HTLs. Moreover, the device stability is also boosted.     

Benzothieno[3,2-b]thiophene-Based Noncovalent Conformational Lock Achieves Perovskite Solar Cells with Efficiency over 24 %

Organic semiconductors with noncovalently conformational locks (OSNCs) are promising building blocks for hole-transporting materials (HTMs). However, lack of satisfied neighboring building blocks negatively impacts the optoelectronic properties of OSNCs-based HTMs and imperils the stability of perovskite solar cells (PSCs). To address this limitation, we introduce the benzothieno[3,2-b]thiophene (BTT) to construct a new OSNC, and the resulting HTM ZS13 shows improved intermolecular charge extraction/transport properties, proper energy level, efficient surface passivation effect. Consequently, the champion devices based on doped ZS13 yield an efficiency of 24.39 % and 20.95 % for aperture areas of 0.1 and 1.01 cm², respectively. Furthermore, ZS13 shows good thermal stability and the capability of inhibiting I⁻ ion migration, thus, leading to enhanced device stability. The success in neighboring-group engineering can triggered a strong interest in developing thienoacene-based OSNCs toward efficient and stable PSCs.     

Tungstate-mediated In-situ Passivation of Grain Boundary Grooves in Perovskite Solar Cells

Possessed with advantageous optoelectronic properties, perovskites have boosted the rapid development of solution-processed solar cells. The performance of perovskite solar cells (PSCs) is significantly weakened by the carrier loss at grain boundary grooves (GBGs); however, it receives limited attention and there lacks effective approach to solve this issue. Herein, for the first time, we constructed the tungstate/perovskite heterointerface via a “two step” in situ reaction approach that provides effective defect passivation and ensures efficient carrier dynamics at the GBGs. The exposed perovskite at grain boundaries is converted to wide-band-gap PbWO₄ via an in-situ reaction between Pb²⁺ and tungstate ions, which passivate defects due to the strong ionic bonding. Moreover, recombination loss is further suppressed via the heterointerface energetics modification based on an additional transformation from PbWO₄ to CaWO₄. PSCs based on this groove modification strategy showed good universality in both normal and inverted structure, with an improved efficiency of 23.25 % in the n-i-p device and 23.33 % in the p-i-n device. Stable power output of the modified device could maintain 91.7 % after around 1100 h, and the device efficiency could retain 92.5 % after aging in air for around 2110 h, and 93.1 % after aging at 85 °C in N₂ for 972 h.     

Managing Secondary Phase Lead Iodide in Hybrid Perovskites via Surface Reconstruction for High-Performance Perovskite Solar Cells with Robust Environmental Stability

Rationally managing the secondary-phase excess lead iodide (PbI₂) in hybrid perovskite is of significance for pursuing high performance perovskite solar cells (PSCs), while the challenge remains on its conversion to a homogeneous layer that is robust stable against environmental stimuli. We herein demonstrate an effective strategy of surface reconstruction that converts the excess PbI₂ into a gradient lead sulfate-silica bi-layer, which substantially stabilizes the perovskite film and reduces interfacial charge transfer barrier in the PSCs device. The perovskite films with such bi-layer could bear harsh conditions such as soaking in water, light illumination at 70 % relative humidity, and the damp-thermal (85 °C and 30 % humidity) environment. The resulted PSCs deliver a champion efficiency up to 24.09 %, as well as remarkable environmental stability, e.g., retaining 78 % of their initial efficiency after 5500 h of shelf storage, and 82 % after 1000 h of operational stability testing.     

A peri-Xanthenoxanthene Centered Columnar-Stacking Organic Semiconductor for Efficient,Photothermally Stable Perovskite Solar Cells

Modulating the structure and property of hole-transporting organic semiconductors is of paramount importance for high-efficiency and stable perovskite solar cells (PSCs). This work reports a low-cost peri-xanthenoxanthene based small-molecule P1, which is prepared at a total yield of 82 % using a three-step synthetic route from the low-cost starting material 2-naphthol. P1 molecules stack in one-dimensional columnar arrangement characteristic of strong intermolecular π–π interactions, contributing to the formation of a solution-processed, semicrystalline thin-film exhibiting one order of magnitude higher hole mobility than the amorphous one based on the state-of-the art hole-transporter, 2,2-7,7-tetrakis(N,N′-di-paramethoxy-phenylamine 9,9′-spirobifluorene (spiro-OMeTAD). PSCs employing P1 as the hole-transporting layer attain a high efficiency of 19.8 % at the standard AM 1.5 G conditions, and good long-term stability under continuous full sunlight exposure at 40 °C.     

Highly efficient perovskite solar cells based on symmetric hole transport material constructed with indaceno[1,2-b:5,6-b']dithiophene core building block

Two novel hole transport materials (HTMs) with indaceno[1,2-b:5,6-b']dithiophene (IDT) as core building blocks,termed IDT1 and IDT2,were designed and synthesized.The side alkyl chains were introduced to regulate and control the morphology and stacking behavior of HTMs,and the peripheral triarylamine arms were introduced to adjust the energy levels and to facilitate efficient hole transport.Applied in mesoporous structured perovskite solar cells (PSCs),HTM IDT1 achieved higher power conversion efficiency (PCE,19.55%) and better stability than Spiro-OMeTAD (19.25%) and IDT2 (15.77%) based PSC.These results suggest the potential of IDTl as a promising HTM for PSCs.