A solids mixing rate correlation for small scale fluidized beds

A new first degree solids mixing rate is proposed to evaluate the mixing of solids in small scale fluidized beds. Particle mixing experiments were carried out in a 2D fluidized bed with a cross-section of 0.02 m × 0.2 m and a height of 1 m. White and black particles with average diameters of 850 and 450 μm were used in our experiments. Image processing was used to measure the concentration of the tracers at different times. The effects of four representative operating parameters (superficial gas velocity, ratio of tracer particles to bed particles, tracer particle position, and particle size) on mixing are discussed with reference to the mixing index. We found that the Lacey index depends on the concentration of the tracers. The position of the tracers affects the initial mixing rate but not the final degree of mixing. However, the new mixing rate equation does not depend on the initial configuration of the particles because this situation is considered to be the initial condition. Using the data obtained in this work and that found in literature, an empirical correlation is proposed to evaluate the mixing rate constant as a function of dimensionless numbers (Archimedes, Reynolds, and Froude) in small scale fluidized beds. This correlation allows for an estimation of the mixing rate under different operating conditions and for the detection of the end point and/or the time of mixing.     

The influence of temperature on limestone sulfation and attrition under fluidized bed combustion conditions

The influence of temperature on attrition of two limestones during desulfurization in a fluidized bed reactor was investigated. Differences in the microstructure of the two limestones were reflected by a different thickness of the sulfate shell formed upon sulfation and by a different value of the ultimate calcium conversion degree. Particle attrition and fragmentation were fairly small under moderately bubbling fluidization conditions for both limestones. An increase of temperature from 850 °C to 900 °C led to an increase of the attrition rate, most likely because of a particle weakening effect caused by a faster CO₂ evolution during calcination. This weakening effect, however, was not sufficiently strong to enhance particle fragmentation in the bed. The progress of sulfation, associated to the build-up of a hard sulfate shell around the particles, led in any case to a decrease of the extent of attrition. Sulfation at 900 °C was less effective than at 850 °C, and this was shown to be related to the porosimetric features of the different samples.     

Hydrodynamics and energy consumption studies in a three-phase liquid circulating three-phase fluid bed contactor

The hydrodynamics and energy consumption have been studied in a cold flow, bubbling and turbulent, pressurized gas–liquid–solid three-phase fluidized bed (0.15 m ID × 1 m height) with concurrent gas–liquid up flow is proposed with the intention of increasing the gas hold up. The hydrodynamic behaviour is described and characterised by some specific gas and liquid velocities. Particles are easily fluidized and can be uniformly distributed over the whole height of the column. The effect of parameters like liquid flow rate, gas flow rate, particle loading, particle size, and solid density on gas hold up and effect of gas flow rate, solid density and particle size on solid hold up, energy consumption and minimum fluidization velocity has been studied. At the elevated pressures a superior method for better prediction of minimum fluidization velocity and terminal settling velocities has been adopted. The results have been interpreted with Bernoulli’s theorem and Richardson–Zaki equation. Based on the assumption of the gas and liquid as a pretend fluid, a simplification has been made to predict the particle terminal settling velocities. The Richardson–Zaki parameter n′ was compared with Renzo’s results. A correlation has been proposed with the experimental results for the three-phase fluidization.     

Rotational asymmetry of reactant concentration and its evolution in a circulating fluidized bed riser

Rotational asymmetric distribution of reactant (ozone) concentration and its evolution along with the gas-solid reactive flow were studied in a 76 mm i.d., 10.2 m high circulating fluidized bed (CFB) riser reactor. The superficial gas velocity ranged from 3 to 5 m/s and the solids circulation rates were 50 and 100 kg/(m² s). Experimental results show that the asymmetry of reactant distribution can extend to a height close to the length of flow developing zone of the CFB riser reactor and then disappears. Based on the hydrodynamics of the gas and solid phases in the solids entrance region, this asymmetry can be attributed to the effect of the solids entrance structure.     

Experimental study of the blockage boundary for dense-phase pneumatic conveying of powders through a horizontal slit

The estimation of the blockage boundary for pneumatic conveying through a slit is of significant importance. In this paper, we investigate the characteristics for blockage of powder (48 μm average diameter) through a horizontal slit (1.6 m × 0.05 m × 0.002 m). The results show that the required critical solid mass flow rate increases as the superficial air velocity increases superficial air velocity. The solid loading ratio and superficial air velocity displayed a decreasing power law relationship. This finding agrees with existing theory and experimental results. However, a minimum inlet solid loading ratio exists. When the air velocity is greater than the corresponding air velocity of the minimum solid loading ratio, the solid loading ratio exhibits an increasing trend in power law. We also found that when the inlet conveying pressure increased, the critical solid mass flow rate required for blockage, the inlet solid loading ratio, and the minimum inlet solid loading ratio increased.     

Study of material agglomeration during nozzle injection of multiviscosity liquid into a fluidized bed reactor by the electric conductance method

Fluidized bed agglomeration is an important and challenging problem for thermal cracking in fluid cokers. A low coker temperature can be problematic because the bitumen is injected into the fluidized bed with a different viscosity, resulting in formation of agglomerates of varying sizes, which slows the cracking reactions. In the present study, the bed material agglomeration process during nozzle injection of multiviscosity liquid was investigated in a fluidized bed operated at different mass ratios of the atomization gas to the liquid jets (GLR = 1%–3.5%) and gas velocities (3.9U_mf and 5.9U_mf) based on a conductance method using a water–sand system to simulate the hot bitumen–coke system at room temperature. During the tests of liquid-jet dispersion throughout the bed, different agglomeration stages are observed at both gas velocities. The critical amount of tert-butanol in the liquid jets that could lead to severe agglomeration of the bed materials (poor fluidization) at GLR = 1% is about 10 wt% at the low fluidizing gas velocity (3.9U_mf) and 18 wt% at the high gas velocity (5.9U_mf). This study provides a new approach for on-line monitoring of bed agglomeration during liquid injection to guarantee perfect contact between the atomized liquid and the bed particles.     

Anti-shock loading capability of a fluidized-bed flocculator

The efficiency of a fluidized-bed flocculator with 800-μm particles of 1360 kg/m³ in density was studied, and the anti-shock capability of the unit was estimated for three kinds of industrial wastewater: heavy turbidity wastewater, dispersed dyeing wastewater and starch wastewater. Steady removal efficiency was contributed by the following characteristics of the flocculator: (1) the dynamic conditions, flocculation time and velocity gradient, which were stabilized at a steady level as the loading rate changed; (2) hydrodynamic characteristics, especially the considerable rise of expanded bed height with increasing superficial velocity when small and light particles were employed as the solid phase; (3) flocs growth characteristics in the fluidized bed, which caused the density and size of the flocs being maintained at a compensational relationship, resulted the stabilized settling velocity of the flocs.     

Magnetic resonance studies of jets in a gas–solid fluidised bed

Magnetic resonance imaging (MRI) has been used to study the behaviour of jets at the distributor of a 50 mm diameter fluidised bed of 0.5 mm diameter poppy seeds. Two perforated-plate distributors were examined, containing either 10 or 14 holes, each 1 mm diameter. Ultra-fast MR imaging was able to show the transient nature of the upper parts of the jets, where discrete bubbles are formed. Imaging in 3D showed that the central jets were the longest for flow rates below minimum fluidisation. Above minimum fluidisation, the outer jets, nearest the wall of the fluidised bed, arched inward towards the central axis. In this latter case, interpretation of the time-averaged 3D image required the use of ultra-fast MR imaging to identify the approximate height above the distributor at which discrete bubbles were formed. The apparently continuous void extending along the central axis above this height in the time-averaged 3D image was thus identified, using ultra-fast MR imaging, as representing the averaged paths of released bubbles. Time-averaged MR velocity mapping was also used to identify dead zones of stationary particles resting on the distributor between the jets. The dead zones could be observed when the superficial velocity of the gas approached minimum fluidisation, but they were smaller than those observed at lower gas superficial velocity. Comparable images of a single jet through 1.2 mm diameter poppy seeds from MRI and electrical capacitance volume tomography (ECVT) are also demonstrated.     

Statistical diagnosis of a gas–solid fluidized bed using Electrical Capacitance Tomography

Fluidization experiments were performed using several particle size distributions of spherical glass particles, ranging from Geldart B to D. An Electrical Capacitance Tomography (ECT) tomograph was utilized in the present study and its usefulness as a diagnostic tool is illustrated. During the experiments a 10.4 cm diameter column was utilized and the column was operated at atmospheric pressure and room temperature (cold fluidized bed). Statistical analyses were performed on the average solid fraction data obtained using the ECT tomograph. Using the time domain skewness and kurtosis the time series could be characterised and the quality of fluidization is determined at different superficial gas velocities (Azizpour, H., Sotudeh-Gharebagh, R., Zarghami, R., Abbasi, M., Mostoufi, N., Mahjoob, M., 2011. Characterization of gas–solid fluidized bed hydrodynamics by vibration signal analysis. International Journal of Multiphase Flow, 37, 788–793). Statistical analysis is also used to characterise the influence of small particles on the bed hydrodynamics.     

Effect of coal particle swarm properties on the fluidization characteristics and coal beneficiation in a dense-phase gas–solid fluidized bed

This paper analyzes the influence of different coal mass fraction in an air dense medium fluidized bed (ADMFB). The effect of the low density particles layer on heavy sedimentation increased with increasing material layer thickness. The thickness of the low density particles layer also affected the final settling time of the high density particles. Increasing the thickness of the low density particles layer by Δh provoked an increase in the settling of high density particles that was related to their diameter (Δh/D). The pressure gradient across the bed was lower than that observed for the control experiment, which had only the dense material, owing to a decrease in the pressure gradient in Zones 1 and 5 (at the top and bottom of the bed, respectively). Introducing different coal sizes resulted in different fluidization environments, particle accumulation layers, and changes to the surrounding zone. However, the influence of the coal particles on the local bed characteristics was related to its concentration. The feeding mass fraction of 6–13 mm size and 13–25 mm size coal should be limited to10% and 13%, respectively. The ranges of possible deviation were found to be 0.08–0.15 and 0.07–0.10 for the respective samples.     

Experimental investigation on flow asymmetry in solid entrance region of a square circulating fluidized bed

To study the influence of back feeding particles on gas-solid flow in the riser, this paper investigated the flow asymmetry in the solid entrance region of a fluidized bed by particle concentration/velocity measurements in a cold square circulating fluidized beds （CFB）. The pressure drop distribution along the riser and the saturation carrying capacity of gas for Geldart-B type particles were first analyzed. Under the condition of u0 = 4 m/s and Gs = 21 kg/（m^2 s）, the back feeding particles were found to penetrate the lean gas-solid flow near the entrance （rear） wall before reaching the opposite （front） wall, thus leading to a relatively denser region near the front wall in the bottom bed. Higher solid circulation rate （u0 =4 m/s, Gs = 33 kg/（m^2 s）） resulted in a higher particle concentration in the riser. However the back feeding particles with higher momentum increased the asymmetry of the particle concentration/velocity profile in the solid entrance region. Lower air velocity （u0 =3.2 m/s） and Gs =21 kg/（m2 s）, beyond the saturation carrying capacity of gas, induced an S-shaped axial solid distribution with a denser bottom zone. This limited the penetration of the back feeding particles and forced the flnidizing air to flow in the central region, thus leading to a higher solid holdup near the rear wall. Under the conditions of uo = 4 m/s and Gs = 21 kg/（m^2 s）, addition of coarse particles （dp= 1145 μm） into the bed made the radial distribution of solids more symmetrical.     

Characteristics of turbulent particle transport in human airways under steady and cyclic flows

Motion of monodispersed aerosol particles suspended in air flow has been studied on realistic transparent model of human airways using Phase Doppler Particle Analyser (P/DPA). Time-resolved velocity data for particles in size range 1–8 μm were processed using Fuzzy Slotting Technique to estimate the power spectral density (PSD) of velocity fluctuations. The optimum processing setup for our data was found and recommendations for future experiments to improve PSD quality were suggested. Typical PSD plots at mainstream positions of the trachea and the upper bronchi are documented and differences among (1) steady-flow regimes and equivalent cyclic breathing regimes, (2) inspiration and expiration breathing phase and (3) behaviour of particles of different sizes are described in several positions of the airway model. Systematically higher level of velocity fluctuations in the upper part of the frequency range (30–500 Hz) was found for cyclic flows in comparison with corresponding steady flows. Expiratory flows in both the steady and cyclic cases produce more high-frequency fluctuations compared to inspiratory flows. Negligible differences were found for flow of particles in the inspected size range 1–8 μm at frequencies below 500 Hz. This finding was explained by Stokes number analysis. Implied match of the air and particle flows thereby indicates turbulent diffusion as important deposition mechanism and confirms the capability to use the P/DPA data as the air flow velocity estimate.     

High photocatalytic efficiency of spouting reactor compared with fluidized bed with top irradiation source

The removal of volatile organic compounds by photocatalytic degradation is one of the safest and most effective ways of removing pollutants from the air. This process is highly affected by the type of reactor, light exposure, and hydrodynamics. For scale up purposes, continuous reactors with high capacity are required for treating large amounts of feedstock. In this work, two types of reactors based on different hydrodynamics, fluidized and spouted reactors, were designed to work under light irradiation inside the reactor. The efficiency of the reactors for volatile organic compound removal from high flow rates of air under Hg lamp irradiation using N–F-TiO₂ photocatalyst was investigated. The performance of the fluidized bed and spouted bed were evaluated and compared at the same weight hourly space velocity of feed stream through the reactor. The results revealed that 80% of the initial acetaldehyde was removed in the fluidized bed after about 200 min, while in the spouted bed the acetaldehyde was totally removed after about 120 min.     

Experimental investigation of turbulence modulation in particle-laden coaxial jets by Phase Doppler Anemometry

The effect of solid particles on the flow characteristics of axisymmetric turbulent coaxial jets for two flow conditions was studied. Simultaneous measurements of size and velocity distributions of continuous and dispersed phases in a two-phase flow are presented using a Phase Doppler Anemometry (PDA) technique. Spherical glass particles with a particle diameter range from 102 to 212 μm were used in this two-phase flow, the experimental results indicate a significant influence of the solid particles and the Re on the flow characteristics. The data show that the gas phase has lower mean velocity in the near-injector region and a higher mean velocity at the developed region. Near the injector at low Reynolds number (Re = 2839) the presence of the particles dampens the gas-phase turbulence, while at higher Reynolds number (Re = 11 893) the gas-phase turbulence and the velocity fluctuation of particle-laden jets are increased. The particle velocity at higher Reynolds number (Re = 11 893) and is lower at lower Reynolds number (Re = 2839). The slip velocity between particles and gas phase existed over the flow domain was examined. More importantly, the present experiment results suggest that, consideration of the gas characteristic length scales is insufficient to predict gas-phase turbulence modulation in gas-particle flows.     

Direct reduction of hematite powders in a fluidized bed reactor

Ultrafine hematite powder was reduced to produce ultrafine iron powder in a 50%Ar–50%H₂ atmosphere at 450–550 °C in a fluidized bed reactor. The ultrafine hematite powder shows the typical agglomerating fluidization behavior with large agglomerates fluidized at the bottom of the bed and small agglomerates fluidized at the upper part of the bed. It was found that defluidization occurred even at the low temperature of 450 °C with low metallization rate. Defluidization was attributed mainly to the sintering of the newly formed iron particles. Granuation was employed to improve the fluidization quality and to tackle the defluidization problem, where granules fluidized like a Geldart's group A powder. Granulation was found to effectively reduce defluidization during reduction, without however sacrificing reduction speed. The as-reduced iron powders from both the ultrafine and the granulated hematite exhibited excellent sintering activity, that is, fast sintering at temperature of as low as ～580 °C, which is much superior as compared to that of nano/ultrafine iron powders made by other processes.     

CFD simulation of a gas–solid fluidized bed with two vertical jets

A computational fluid dynamics (CFD) model is used to investigate the hydrodynamics of a gas–solid fluidized bed with two vertical jets. Sand particles with a density of 2660 kg/m³ and a diameter of 5.0 × 10^?4 m are employed as the solid phase. Numerical computation is carried out in a 0.57 m × 1.00 m two-dimensional bed using a commercial CFD code, CFX 4.4, together with user-defined Fortran subroutines. The applicability of the CFD model is validated by predicting the bed pressure drop in a bubbling fluidized bed, and the jet detachment time and equivalent bubble diameter in a fluidized bed with a single jet. Subsequently, the model is used to explore the hydrodynamics of two vertical jets in a fluidized bed. The computational results reveal three flow patterns, isolated, merged and transitional jets, depending on the nozzle separation distance and jet gas velocity and influencing significantly the solid circulation pattern. The jet penetration depth is found to increase with increasing jet gas velocity, and can be predicted reasonably well by the correlations of Hong et al. (2003) for isolated jets and of Yang and Keairns (1979) for interacting jets.     

Experimental study of the effect of friction phenomena on actual and calculated inventory in a small-scale CFB riser

Accurate information concerning riser inventory in a fluidized bed is required in some applications such as the calcium looping process, because it is related to the CO₂ capture efficiency of the system. In a circulating fluidized bed (CFB), the riser inventory is normally calculated from the riser pressure drop; however, the friction and the acceleration phenomena may have a significant influence on the total riser pressure drop. Therefore, deviation may occur in the calculation from the actual mass. For this reason the magnitude of the friction and the acceleration pressure drop in the entire riser is studied in small-scale risers. Two series of studies were performed: the first one in a scaled cold model riser of the 10 kW_th facility, and the second one in the 10 kW_th fluidized bed riser under process conditions. The velocities were chosen to comply with the fluidization regimes suitable for the calcium looping process, namely, the turbulent and the fast. In cold-model experiments in a low-velocity turbulent fluidization regime, the actual weight (static pressure drop) of the particles is observed more than the weight calculated from a recorded pressure drop. This phenomenon is also repeated in pilot plant conditions. In the cold-model setup, the friction and acceleration pressure drop became apparent in the fast fluidization regime, and increased as the gas velocity rose. Within calcium looping conditions in the pilot plant operation, the static pressure drop was observed more than the recorded pressure drop. Therefore, as a conservative approach, the influence of friction pressure drop may be neglected while calculating the solid inventory of the riser. The concept of transit inventory is introduced as a fraction of total inventory, which lies in freefall zones of the CFB system. This fraction increases as gas velocity rises.     

Constraint strength and axial/radial particle velocity profiles for an integrated riser outlet

To study axial/radial profiles of particle velocity in the affected region of an integrated riser outlet, a cold model was developed for the integrated riser reactor combining the gas–solid distributor with the fluidized bed. Constraints, related to the gas–solid distributor and the upper fluidized bed, imposed on the particle flow in the riser outlet region, were investigated experimentally. The experimental results showed that with increasing superficial gas velocity, these constraints have strong influences on particle flow behavior, the particle circulation flux in the riser, and the height of the static bed material of the upper fluidized bed. When the constraints have greater prominence, the axial profile of the cross-sectionally averaged particle velocity in the outlet region initially increases and then decreases, the rate of decrease being proportional to the constraint strength. Along the radial direction of the outlet section, the region where the local particle velocity profile tends to decrease appears near the dimensionless radius r/R = 0.30 initially and then, with increasing constraint strength, gradually extends to the whole section from the inner wall. Based on the experimental data, an empirical model describing the constraint strength was established. The average relative error of the model is within 7.69%.     

Application of DEM modified with enlarged particle model to simulation of bead motion in a bead mill

We applied the discrete element method (DEM) of simulation modified by an enlarged particle model to simulate bead motion in a large bead mill. The stainless-steel bead mill has inner diameter of 102 mm and mill length of 198 mm. The bead diameter and filling ratio were fixed respectively at 0.5 mm and 85%. The agitator rotational speed was changed from 1863 to 3261 rpm. The bead motion was monitored experimentally using a high-speed video camera through a transparent mill body. For the simulation, enlarged particle sizes were set as 3–6 mm in diameter. With the DEM modified by the enlarged particle model, the motion of enlarged particles in a mill was simulated. The velocity data of the simulated enlarged particles were compared with those obtained in the experiment. The simulated velocity of the enlarged particles depends on the virtual frictional coefficient in the DEM model. The optimized value of the virtual frictional coefficient can be determined by considering the accumulated mean value. Results show that the velocity of the enlarged particles simulated increases with an increase in the optimum virtual frictional coefficient, but the simulated velocity agrees well with that determined experimentally by optimizing the virtual frictional coefficient in the simulation. The computing time in the simulation decreases with increased particle size.     

Fluidization and bubbling behavior of potash particles in a deep fluidized bed

Most existing models for predicting bubble size and bubble frequency have been developed for freely bubbling fluidized beds. Accurate prediction of bubbling behavior in deep fluidized beds, however, has been a challenge due to the higher degree of bubble coalescence and break up, high probability of the slugging regime, partial fluidization, and chaotic behavior in the bubbling regime. In this work, the bubbling and fluidization behavior of potash particles was investigated in a deep fluidized bed employing a twin-plane electrical capacitance tomography (ECT) system. Solid volume fraction, average bubble velocity, average bubble diameter, and bubble frequency in both bubbling and slugging regimes were measured at two different bed height ratios (H/D = 3.5 and H/D = 3.78). This work is the first to illustrate a sequential view of bubbles at different superficial gas velocities in a fluidized bed. The results show that both the bubble diameter and rising velocity increased with increasing the superficial gas velocity for the two bed heights, with larger values observed in the deeper bed compared to the shallower one. Predicted values for bubble diameter, bubble rise velocity and bubble frequency from different models are compared with the experimental data obtained from the ECT system in this work. Good agreement has been achieved between the values predicted by the previous models and the experimental data for the bubble diameter and bubble rise velocity with an average absolute deviation of 16% and 15% for the bed height of 49 cm and 13% and 8% for the bed height of 53 cm, respectively.