A selective colorimetric and fluorescence chemosensing sensor for Cr<Superscript>3+</Superscript> based on a rhodamine base derivative

A rhodamine-conjugated coumarin (L) was used in designing a selective fluorescence chemosensor for the determination of trace amounts of Cr³⁺ ions in acetonitrile–water (MeCN/H₂O (90:10, %v/v) solutions. The intensity of the fluoresce emission of the chemosensor is intensified upon addition of Cr³⁺ ions in MeCN/H₂O (90:10, %v/v) solutions, due to the formation of a selective 1:1 complex between L and Cr³⁺ ions. The fluorescence enhancement versus Cr³⁺ concentration has been found to be linear from 1.0?×?10^?7 to 1.8?×?10^?5 M and a detection limit of 7.5?×?10^?8 M. The proposed fluorescent probe proved to be highly selective towards Cr³⁺ ions as compared to other common metal ions and could be successfully applied to the determination of Cr³⁺ concentrations in some water and wastewater samples.     

Trace Analysis of Al (III) Ions Based on the Redox Current of a Conducting Polymer

A conducting polymer was electrochemically prepared on a Pt electrode with newly synthesized 3′‐(4‐formyl‐3‐hydroxy‐1‐phenyl)‐5,2′ : 5′,2″‐terthiophene (FHPT) in a 0.1 M TBAP/CH₂Cl₂ solution. The polymer‐modified electrode exhibited a response to proton and metal ions, especially Al(III) ions. The poly[FHPT] was characterized with cyclic voltammetry, EQCM, and applied to the analysis of trace levels of Al(III) ions. Experimental parameters affecting the response of the poly[FHPT] were investigated and optimized. Other metal ions in low concentration did not interfere with the analysis of Al(III) ions in a buffer solution at pH 7.4. The response was linear over the concentration range of 5.0×10^?8–7.0×10^?10 M, and the detection limit was 5.0×10^?10 M using the linear sweep voltammetry (LSV). Employing the differential pulse voltammetry (DPV), the response was linear over the 1.0×10^?9–5.0×10^?11 M range and the detection limit was 3.0×10^?11 M. The relative standard deviation at 5.0×10^?11 M was 7.2% (n=5) in DPV. This analytical method was successfully verified for the analysis of trace amounts of Al(III) ions in a human urine sample.     

Binding of Scandium Ions to Metalloporphyrin–Flavin Complexes for Long‐Lived Charge Separation

A porphyrin–flavin‐linked dyad and its zinc and palladium complexes (MPor?Fl: 2 ?M, M=2 H, Zn, and Pd) were newly synthesized and the X‐ray crystal structure of 2 ?Pd was determined. The photodynamics of 2 ?M were examined by femto‐ and nanosecond laser flash photolysis measurements. Photoinduced electron transfer (ET) in 2 ?H₂ occurred from the singlet excited state of the porphyrin moiety (H₂Por) to the flavin (Fl) moiety to produce the singlet charge‐separated (CS) state ¹(H₂Por^.+?Fl^.?), which decayed through back ET (BET) to form ³[H₂Por]*?Fl with rate constants of 1.2×10¹⁰ and 1.2×10⁹ s^?1, respectively. Similarly, photoinduced ET in 2 ?Pd afforded the singlet CS state, which decayed through BET to form ³[PdPor]*?Fl with rate constants of 2.1×10¹¹ and 6.0×10¹⁰ s^?1, respectively. The rate constant of photoinduced ET and BET of 2 ?M were related to the ET and BET driving forces by using the Marcus theory of ET. One and two Sc³⁺ ions bind to the flavin moiety to form the Fl?Sc³⁺ and Fl?(Sc³⁺)₂ complexes with binding constants of K₁=2.2×10⁵ M ^?1 and K₂=1.8×10³ M ^?1, respectively. Other metal ions, such as Y³⁺, Zn²⁺, and Mg²⁺, form only 1:1 complexes with flavin. In contrast to 2 ?M and the 1:1 complexes with metal ions, which afforded the short‐lived singlet CS state, photoinduced ET in 2 ?Pd???Sc³⁺ complexes afforded the triplet CS state (³[PdPor^.+?Fl^.??(Sc³⁺)₂]), which exhibited a remarkably long lifetime of τ=110 ms (k_BET=9.1 s^?1).     

Development of Fluorescent Film Sensors Based on Electropolymerization for Iron(III) Ion Detection

Two electroactive materials, M1 and M2 , are synthesized and their fluorescent electropolymerized (EP) films are prepared and used to detect metal ions. From the tested metal ions, M1 and M2 are demonstrated to be sensitive and selective for Fe³⁺ ions. In particular, M2 exhibits higher sensitivity towards Fe³⁺ ions. The fluorescent detection ranges from 10^?5 M to 4×10^?4 M . The excellent performance of the EP fluorescent films is mainly due to the strong metal‐chelated properties of M2 and the intrinsic porous cross‐linked‐network microstructure of the EP films. This study, thus, provides a promising Fe³⁺ sensing candidate and a potential preparation method for fluorescent sensing films.     

Highly Selective and Sensitive Tin(II) Membrane Electrode Based on a New Synthesized Schiff's Base

Studies on complex formation of tris(3‐(2‐hydroxybenzophenone)propyl)amine (THPA) with a number of metal ions in acetonitrile solution revealed the occurrence of a selective 1 : 1 complexation of the proposed ligand with Sn²⁺ ion. Consequently, THPA was used as a suitable neutral ionophore for the preparation of a polymeric membrane‐selective electrode. The electrode exhibits a Nernstian behavior with a slope of 29.4±0.3 mV per decade and a detection limit of 2.0×10^?7 M. It also showed a good selectivity for Sn²⁺ ions in comparison with some of group A and B metal ions over a wide concentration range of 5.0×10^?7–1.0×10^?1 M. Improved selectivity was achieved compared to the best selectivity recently reported by other authors for tin(II). The electrode was successfully applied to the determination of Sn²⁺ ion in waste water and various canned products.     

Preparation of Cu (II) imprinted polymer electrode and its application for potentiometric and voltammetric determination of Cu (II)

The Cu (II) imprinted polymer glassy carbon electrode (GCE/Cu-IP) was prepared by electropolymerization of pyrrole at GCE in the presence of methyl red as a dopant and then imprinting by Cu²⁺ ions. This electrode was applied for potentiometric and voltammetric detection of Cu²⁺ ion. The potentiometric response of the electrode was linear within the Cu²⁺ concentration range of 3.9 × 10^?6 to 5.0 × 10^?2 M with a near-Nernstian slope of 29.0 mV decade^?1 and a detection limit of 5.0 × 10^?7 M. The electrode was also used for preconcentration anodic stripping voltammetry and results exhibited that peak currents for the incorporated copper species were dependent on the metal ion concentration in the range of 1.0 × 10^?8 to 1.0 × 10^?3 M and detection limit was 6.5 × 10^?9 M. Also the selectivity of the prepared electrode was investigated. The imprinted polymer electrode was used for the successful assay of copper in two standard reference material samples.     

Iron(III) selective fluorescence probe based on perylene tetracarboxylic diimide

Responses of organic fluorophore, perylenediimide derivative N,N′-di[3-[2-(3-thienyl)ethyl]phenyl]perylene-3,4,9,10-bis-(dicarboxyimide) (PDI1) was investigated in polymer matrix of polyvinyl chloride (PVC) by emission spectrometry. Its response to Fe(III) ions was evaluated in terms of the effect of pH. The properties of time dependent response, reversibility, limit of detection, linear concentration range for the metal ion and repeatability characteristics of the sensing element also have been studied. The offered sensor exhibited remarkable fluorescence intensity quenching at pH 6.0 in the concentration range of 1 × 10^?6 to 2.5 × 10^?3 M Fe(III) ions. The reproducibility of the sensor membrane was investigated by alternately changing the solution between 1 × 10^?4 M Fe(III) in Na₂HPO₄ (4 × 10^?2 M) and NaH₂PO₄ buffer (2 × 10^?3 M).     

1,3,4-Trisubstituted-2-azetidinone Derivatives as Novel Receptors for Bismuth(III) Ion-Selective Electrodes: Application in Pharmaceutical and Glass Samples

Abstract

Polymeric membrane electrodes (PMEs) and coated graphite electrodes (CGEs) containing 1,3,4-trisubstituted-2-azetidinone derivatives as ion carriers are reported here for bismuth(III) ion selectivity. These electrodes exhibited Nernstian response for Bi³⁺ ions over a wide concentration range (5.0 × 10^?7 M to 1.0 × 10^?1 M for CGE) with a lower detection limit of 3.98 × 10^?7 M (for CGE) and wide pH range (1.3–5.0). Compared to polymeric membrane electrode, the coated graphite electrode has shown better selectivity for Bi³⁺ ions with respect to common metal ions. Proposed electrodes have been used for the estimation of Bi³⁺ ions in pharmaceutical and glass samples.     

Highly Sensitive and Selective Detection of Pb(II) by NH2−SiO2/Ru(bpy)32+−UiO66 based Solid‐state ECL Sensor

In this study, a novel electrochemiluminescence (ECL) sensor for highly sensitive and selective detection of Pb(II) was developed based on Ru(bpy)₃²⁺ encapsulated UiO66 metal‐organic‐framework (Ru(bpy)₃²⁺?UiO66 MOF) and ?NH₂ group functionalized silica (NH₂?SiO₂). The NH₂?SiO₂ with large surface area provided an excellent platform for the ECL sensor. As numerous exposed carboxyl groups were present on UiO66 backbone, the Ru(bpy)₃²⁺?UiO66 could be steadily immobilized to NH₂?SiO₂ by forming amide bonds. Meanwhile, the introduced UiO66 MOF which used for the encapsulation of Ru(bpy)₃²⁺, significantly enhanced the ECL efficiency of the proposed sensor, as it possessed a large specific surface area and porosity for the loading of Ru(bpy)₃²⁺. Moreover, a high quenching effect on ECL intensity was obtained in the presence of Pb(II) in the electrolyte. Under the optimal conditions, the quenched ECL intensity showed a good linear relationship within Pb(II) concentration in the range from 1.0×10^?6 to 1.0×10² μM, with a detection limit of 1.0×10^?7 μM (S/N=3). The proposed sensor for Pb(II) detection was simple in operation, rapid in testing, stable in signal, and showed a good anti‐interference ability to some other metal ions. Besides, its application for detecting Pb(II) in a real sample was also investigated here. This work provides a potential platform for metal ions detection in environmental monitoring field.     

Tb3+ PVC-Membrane Electrode Based on 2-{2-(2-Anilinocarbothioyl)hydrazino)-2-oxoacetyl}-N-phenyl-1-hydrazine Carbothioamide

Abstract

The polyvinyl chloride (PVC) membrane containing 2-{2-(2-anilinocarbothioyl)hydrazino)-2-oxoacetyl}-N-phenyl-1-hydrazinecarbothioamide (AHC) as a suitable iophore exhibits a Nernstian response for Tb³⁺ ions over a wide concentration range (1.0 × 10^?6 to 1.0 × 10^?2 M) with a slope of 19.6 ± 0.3 mV per decade and a limit of detection of 6.8 × 10^?7 M in the pH range 3.5–8.5. The proposed sensor revealed very good selectivities (expect for the Pr³⁺ and Ho³⁺ ions) for a wide variety of other metal ions. The practical utility of the electrodes has been demonstrated by its use for the determination of Tb³⁺ in different solutions.     

Magnesium-PVC Membrane Sensor Based on 4,5-Bis(Benzoylthio)-1,3-Dithiole-2-Thione

Abstract

This report describes an attempt to develop potentiometric Mg²⁺ sensors based on a liquid polymeric membrane. Membrane incorporating 4,5-Bis(benzoylthio)-1,3- dithiole-2-thione (Bz₂dmit) as ionophore, with composition Bz₂ dmit:NaTPB:NB:PVC in the ratio 2.5:2.5:65:30 (w/w), exhibits the best result for potentiometric sensing of Mg²⁺ ions. The proposed electrode, based on Bz₂ dmitwith nitrobenzene (NB) as a solvent mediator in a polyvinyl chloride (PVC) membrane matrix, exhibited a near-Nernstian response to Mg²⁺ in the concentration range of 1.0 × 10^?5 to 1.0 × 10^?1 M, with a slope of 29.2 mV per decade of activity of Mg²⁺. The lower limit of detection was 1.0 × 10^?5 M. This sensor showed high selectivity with respect to alkaline, alkaline earth, transition, and heavy metal ions, except for Sr²⁺, and could be used over a pH range of 3.5–9.0. It can be used for at least 2 mo without considerable divergence in potentials and has a relatively fast response of <10 s. It was applied successfully as an indicator electrode in potentiometric titration of Mg²⁺ ions with EDTA.     

Terbium(III) Ion-Selective Electrochemical Sensor Based on Hematoporphyrin

Abstract

A polyvinyl chloride (PVC) based membrane sensor for terbium ions was prepared by employing Hematoporphyrin (HP) as an ionophore. The sensor revealed a very good selectivity (expect for the Fe³⁺ion) with respect to common alkali, alkaline earth and heavy metal ions. The plasticized membrane electrode exhibits a Nernstian response for Tb³⁺ ions over a wide concentration range (1.0 × 10^?6 ? 1.0 × 10^?2 M) with a slope of 19.8±0.3 mV per decade and low detection limit of 7.4 × 10^?7 M. The developed sensor was used in determination of F^? in mouth wash preparation sample.     

Solid‐Contact Potentiometric Sensor Based on Polyaniline and Unsubstituted Pillar[5]Arene

A novel potentiometric sensor based on screen‐printed carbon electrode covered with electropolymerized polyaniline (PANI) and unsubstituted pillar[5]arene as ionophore has been developed and tested in potentiometric measurements of pH and metal ions. The introduction of pillar[5]arene improved the reversibility of the pH response in the range from 2.0 to 9.0 with the slope of 45 mV/pH. Among metal cations, the response to Fe³⁺ and Ag⁺ ions was referred to PANI redox conversion whereas the signal toward Cu²⁺ in the range from 1.0×10^?6 to 1.0×10^?2 M (limit of detection (LOD) 3.0×10^?7 M) to specific interaction with the macrocycle.     

A Highly Sensitive Quinoline-Containing Rhodamine B Thiohydrazide Based Fluorescent Probe for Hg2+ in Aqueous Solution and Living Cells

Quinoline-appended rhodamine B thiohydrazide based fluorescent probe was designed and applied in fluorescent detections of mercury ions in both aqueous solution and living cells. The signal change of the probe is based on a specific metal ion induced reversible ring-opening mechanism of a rhodamine B thiohydrazide. The probe exhibits a dynamic response concentration range for Hg²⁺ from 1.0 × 10^?8 to 1.0 × 10^?5 M with a detection limit of 8.5 × 10^?9 M. The fluorescent probe is pH independent in medium condition and exhibits high selectivity over other common metal ions.     

Ionophores in Rubidium Ion‐Selective Membrane Electrodes

Binaphthyl‐based crown ethers incorporating anthraquinone, benzoquinone, and 1,4‐dimethoxybezene have been synthesized and tested for Rb⁺ selective ionophores in the poly(vinyl chloride) (PVC) membrane. The membrane containing NPOE gave a better Rb⁺ selectivity than those containing either DOA or BPPA as a plasticizer. The response was linear within the concentration range of 1.0×10^?5–1.0×10^?1 M and the slope was 54.7±0.5 mV/dec. The detection limit was determined to be 9.0×10^?6 M and the optimum pH range of the membrane was 6.0–9.0. The ISE membrane exhibits good selectivity for Rb⁺ over ammonium, alkali metal, and alkaline earth metal ions. Selectivity coefficients for the other metal ions, log K^Pot were ?2.5 for Li⁺, ?2.4 for Na⁺, ?2.0 for H⁺, ?1.0 for K⁺, ?1.2 for Cs⁺, ?1.6 for NH₄⁺, ?4.5 for Mg²⁺, ?5.0 for Ca²⁺,?4.9 for Ba²⁺. The lifetime of the membrane was about one month.     

Cobalt(II)-selective membrane electrode based on N,N′-di(thiazol-2-yl)formimidamide

A new PVC-membrane electrode for Co²⁺ ions based on N,N′-di(thiazol-2-yl)formimidamide (TF) as membrane carrier has been developed. The electrode resulted in Nernstian response (29.5?±?0.4?mV decade^?1) for Co²⁺ ion over a wide concentration range (2.5?×?10^?7 ?1.0?×?10^?1?M) with a detection limit of 6.1?×?10^?8?M. The sensor has a response time of about 10?s, and can be used for at least 2 months without observing any deviation from the Nernstain response. The electrode revealed good selectivity towards cobalt(II) ion over a wide variety of alkali, alkaline earth, transition, and heavy metal ions and could be used in the pH range 2.0–7.0. The electrode was used for determination of Co²⁺ in real samples.     

Novel Potentiometric PVC‐Membrane and Coated Graphite Sensors for Lanthanum(III)

Preliminary theoretical studies revealed the selective complexation of bis (2‐mercaptoanil) diacetyl (BMDA) with La³⁺ over several alkali, alkaline earth and heavy metal ions. Thus, novel PVC‐based membrane (PBM) and coated graphite membrane (CGM) sensors for La(III) based on BMDA were prepared. The electrodes display Nernstian behavior over wide concentration ranges (i.e., 1.0×10^?5–1.0×10^?1 M for PBM and 1.0×10^?6–1.0×10^?1 M for CGM). The potential response of sensors was pH independent in the range of 4.0–8.0. The sensors possess satisfactory reproducibility, fast response time (<15 s), and specially excellent discriminating ability for La³⁺ ions with respect to most of the cations. The membrane sensor was used as an indicator electrode in potentiometric titration of lanthanum ions with EDTA. The coated graphite membrane electrode was applied in determination of fluoride ions in mouth wash preparations.     

Highly Sensitive Electrochemiluminescence Detection of Mercury(II) Ions Based on DNA‐Linked Luminol‐Au NPs Superstructure

A novel highly sensitive electrochemiluminescence (ECL) detection protocol for mercury(II) ions was developed. Based on the strong and stable thymine? thymine mismatches complexes coordination chemistry, mercury(II) ions can specifically bind to a designed DNA strand, leading to the release of the complimentary DNA strand. The released DNA strand was then captured by magnetic beads modified with specific DNA, and then through the formation of DNA‐linked luminol‐Au nanoparticles (NPs) superstructure, a specific ECL system for mercury(II) ions was developed. Using 3‐aminopropyl‐triethoxysilane as an effective enhancer, the ECL system can detect Hg²⁺ ion within a linear range from 2.0×10^?10 mol L^?1 to 2.0×10^?8 M, with a detection limit as low as 1.05×10^?10 M (3σ). Moreover, this ECL system is highly specific for Hg²⁺, without interference from other commonly coexisted metal ions, and it can be used for the analysis of real samples.     

Kinetic studies on the metal(II) tartarate–peroxomonosulfate reaction

The kinetics of oxidation of tartaric acid (TAR) by peroxomonosulfate (PMS) in the presence of Cu(II) and Ni(II) ions was studied in the pH range 4.05–5.20 and also in alkaline medium (pH ～12.7). The rate was calculated by measuring the [PMS] at various time intervals. The metal ions concentration range used in the kinetic studies was 2.50 × 10^?5 to 1.00 × 10^?4 M [Cu(II)], 2.50 × 10^?4 to 2.00 × 10^?3M [Ni(II)], 0.05 to 0.10 M [TAR], and µ = 0.15 M. The metal(II) tartarates, not TAR/tartarate, are oxidized by PMS. The oxidation of copper(II) tartarate at the acidic pH shows an appreciable induction period, usually 30–60 min, as in classical autocatalysis reaction. The induction period in nickel(II) tartarate is small. Analysis of the [PMS]–time profile shows that the reactions proceed through autocatalysis. In alkaline medium, the Cu(II) tartarate–PMS reaction involves autocatalysis whereas Ni(II) tartarate obeys simple first‐order kinetics with respect to [PMS]. The calculated rate constants for the initial oxidation (k₁) and catalyzed oxidation (k₂) at [TAR] = 0.05 M, pH 4.05, and 31°C are Cu(II) (1.00 × 10^?4 M): k₁ = 4.12 × 10^?6 s^?1, k₂ = 7.76 × 10^?1 M^?1s^?1 and Ni(II) (1.00 × 10^?3 M): k₁ = 5.80 × 10^?5 s^?1, k₂ = 8.11 × 10^?2 M^?1 s^?1. The results suggest that the initial reaction is the oxidative decarboxylation of the tartarate to an aldehyde. The aldehyde intermediate may react with the alpha hydroxyl group of the tartarate to give a hemi acetal, which may be responsible for the autocatalysis. © 2011 Wiley Periodicals, Inc. Int J Chem Kinet 43: 620–630, 2011     

The effect of thallium ions on the gold dissolution rate in thiosulfate electrolytes

The effect of TlNO₃ additions in the concentration (c ₁) range from 5 × 10^?6 to 1 × 10^?4 M on the anodic dissolution of gold in sodium thiosulfate solutions with the concentration (c ₂) from 0.005 to 0.2 M is studied by voltammetry on the electrode surface renewed by cutting off a thin metal layer immediately in solution and also by the quartz-crystal microbalance method. For c ₂ = 0.2 M, as c ₁ increases from 5 × 10^?6 to 1 × 10^?4 M, the gold anodic dissolution rate is observed to increase from 0.02 (in the absence of TlNO₃) to 0.75 mA/cm² for c ₁ = 7.5 × 10^?5 M according to a nearly linear law. The dissolution accelerates because the effective values of the transfer coefficient and the exchange current density increase from 0.2 and 4 ??A/cm² (in the absence of TlNO₃ admixtures) to 0.47 and 35 ??A/cm² (for c ₁ = 1 × 10^?4), respectively. Experiments with the renewal of the electrode surface in the course of electrolysis suggest that the gold dissolution is catalyzed in the presence of thallium ions by the adsorption mechanism and also as the result of the mixed kinetics of their adsorption on the electrode surface.