Developments and structures of mesopores in alkaline-treated ZSM-5 zeolites

ZSM-5 zeolites with SiO₂/Al₂O₃ molar ratio of 24 were treated in 0.05 M aqueous sodium hydroxide solution at 325 K in different periods. The samples were characterized by means of nitrogen adsorption at 77 K, field emission scanning electron microscopy, X-ray diffractometry, and Fourier transform infrared spectroscopy. Analysis of the experimental results showed that the alkaline treatment periods have influence on the developments and structures of mesopores in the alkaline-treated ZSM-5 zeolites. Alkaline treatment initially develops mesopores mainly from the boundary portion of MFI zeolites to the bulk, while prolonged treatment destroys the mesopores, and an optimum mesoporosity is obtained by the treatment for 1.5 h. On the other hand, crystallinities and short-range order in alkaline treated zeolites have remained virtually unchanged according to the examination from X-ray diffractometry and Fourier transform infrared spectroscopy.     

ZSM-5 monolith of uniform mesoporous channels

A ZSM-5 monolith of uniform mesopores(meso-ZSM-5) was synthesized with the template method using carbon aerogel of uniform mesopores of great pore volume. The pore size distribution determined by N2 adsorption showed the presence of mesopores with an average pore width of 11 nm and micropores with an average pore width of 0.51 nm. Field emission scanning electron micrograph observation revealed the presence of uniform mesopores. X-ray diffraction and FT-IR provided evidence that the synthesized meso-ZSM-5 monolith has a highly crystalline ZSM-5 structure.     

Comparative study on pore structures of mesoporous ZSM-5 from resorcinol-formaldehyde aerogel and carbon aerogel templating

Resorcinol-formaldehyde aerogels and carbon aerogels of different mesoporosities have been used as templates for preparing bimodal zeolites of mesopores. Samples were thoroughly characterized with X-ray diffraction, field emission scanning electron microscopy, thermogravimetric analysis, X-ray photoelectron spectroscopy, N(2) adsorption at 77 K, as well as FT-IR spectroscopy and (29)Si nuclear magnetic resonance spectroscopy. The mesoporous ZSM-5 zeolites have additional mesopores of 9-25 nm in widths and 0.07-0.2 cm(3)/g in volumes, besides their perfect inherent micropores. Experimental results show the mesoporous systems of the finally obtained zeolites can be influenced by proper preparation of resorcinol-formaldehyde aerogels and carbon aerogels through solution chemistry. Consequently, zeolites of tunable mesoporosities can be prepared with this unique methodology.     

One-step fabrication and high photocatalytic activity of porous TiO2 hollow aggregates by using a low-temperature hydrothermal method without templates

Porous TiO2 hollow aggregates have been synthesized on a large scale by means of a simple hydrothermal method without using any templates. The as-prepared products were characterized by means of field emission scanning electron microscopy, XRD, TEM, nitrogen adsorption, UV/Vis diffuse reflectance spectroscopy, and FTIR spectroscopy. The photocatalytic activity of the aggregates was demonstrated through the photocatalytic degradation of Rhodamine B. Structural characterization indicates that the porous TiO2 aggregates are 500-800 nm in diameter and display mesoporous structure. The average pore sizes and BET surface areas of the aggregates are 12 nm and 168 m2 g-1, respectively. Optical adsorption investigations show that the aggregates possess an optical band-gap energy of 3.36 eV. The as-prepared products were substantially more effective photocatalysts than the commercially available photocatalyst P25. The dye degradation rate of the porous TiO2 hollow aggregates is more than twice that of P25. The high photoactivities of the aggregates can be attributed to the combined effects of several factors, namely, large surface areas, the existence of mesopores, and the high band-gap energy. In addition, the as-prepared products can be easily recycled.     

Physicochemical and catalytic properties of micro-mesoporous zeolite materials

Micro-mesoporous zeolite materials differing in their content of micro- and mesopores are obtained by the recrystallization of modernite zeolite. Using physicochemical methods such as scanning electron microscopy, transmission electron microscopy, X-ray powder diffraction analysis, small-angle X-ray scattering analysis, low-temperature adsorption of nitrogen, temperature-programmed desorption of NH3, and IR spectroscopy, it is shown that recrystallization leads first to the formation of mesopores with sizes of 20–30 Å in zeolite crystals, then to the appearance of zeolite/MCM-41 nanocomposite, and finally to the complete conversion of zeolite into mesoporous MCM-41. During this process, the concentration of strong Brønsted acid sites accessible to pyridine bases first increases then drops. The catalytic properties of the synthesized materials are studied in the reaction of alkylation of benzene by dodecene-1. It is shown that the creation of transport pores and the increase in the accessibility of acid sites due to recrystallization under soft conditions facilitate the alkylation reaction.     

Synthesis and characterization of small-mesopore-added silicalite-1 zeolites using single wall carbon nanohorn templating

Small-mesopore-added silicalite-1 zeolites were prepared by using single wall carbon nanohorn (SWCNH) as a template. The samples were characterized with X-ray powder diffraction, field emission scanning electron microscopy, transmission electron microscopy (TEM) and molecular probe adsorption methods. The pore size distributions determined with N₂ adsorption at 77 K showed the presence of small mesopores in 2–4 nm pore widths, in addition to their intrinsic micropores of 0.58 nm. The mesopore volume was 0.06 cm³ g^?1. The presence of small mesopores in the SWCNH-templated silicalite-1 zeolites was supported with TEM observation as well as the liquid phase adsorption of methylene blue, which was much higher than that on a bulk (purely microporous) silicalite-1.     

具有丰富介孔Cu-SAPO-34催化剂制备及其低温氨气选择性催化还原反应(英文)

氮氧化物(NO_x)是主要的大气污染物之一,与光化学烟雾、全球气候变暖等环境问题密切相关.随着汽车产业的高速发展,柴油车排放尾气中的NOx脱除成为国内外尾气催化净化领域最突出的难点之一.其中氨气选择性催化还原技术(NH_3-SCR)由于其高效率、低成本的特征已成为主要的移动源脱硝技术.目前,实际应用中最广泛的是V_2O_5-WO_3(MoO_3)/TiO_2催化剂,然而一些不可避免的因素仍然存在,比如V具有较强的毒性,较高的操作温度,较窄的活性温度窗口以及易将SO_2氧化为SO_3导致催化剂表面会有大量的硫酸盐沉积而失活等.因此很有必要开发一种无钒SCR催化剂.近年来,分子筛负载过渡金属作为催化剂引起了研究者的广泛兴趣,其中Cu-CHA分子筛催化剂因其高SCR活性,高N2选择性,较宽的温度窗口以及优异的稳定性引起研究者的广泛关注.就Cu/SAPO-34而言,传统的制备方法是利用离子交换法将Cu离子引入到SAPO-34微孔孔道中,然而由于微孔会限制Cu离子的分布,导致绝大多数Cu优先分布在分子筛外表面,从而限制了其活性发挥.Martínez-Franco课题组利用双模板一步法成功制备了Cu-SAPO-34催化剂,提高了分子筛中活性Cu离子数目.Peden课题组发现在NOx的NH_3-SCR反应中Cu-SAPO-34催化剂存在低温动力学限制.因此开发一种具有丰富介孔的多级孔Cu-SAPO-34催化剂势在必行.我们利用一步水热晶化法成功制备了一系列具有丰富介孔的Cu-SAPO-34催化剂.采用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、氮气吸附-脱附、X射线衍射(XRD)、~(27)Al核磁共振(Al-NMR)、紫外可见漫反射光谱(UV-Vis DRS)、电感耦合等离子体-原子发射光谱(ICP-AES)、X射线光电子能谱(XPS)、氢气程序升温还原(H2-TPR)和电子顺磁共振(EPR)等表征手段研究了Cu-SAPO-34多级孔催化剂的物理化学性质.XRD测试结果证实,H-Cu-SAPO-34催化剂具有典型的CHA结构.TEM和N2吸附-脱附测试结果表明,H-Cu-SAPO-34催化剂具有丰富的介孔结构.Al-NMR测试结果表明,多种配位的Al物种存在于H-Cu-SAPO-34中.UV-Vis DRS测试结果证实了孤立Cu~(2+)和高分散的CuO的存在,没有观察到(Cu-O-Cu)2+和CuAl2O4物种的存在.ICP-AES和XPS测试结果表明,H-Cu-SAPO-34催化剂具有相似的Cu含量,并且H-Cu-SAPO-34-20催化剂具有最高的Cu~(2+)含量.H2-TPR测试结果表明,H-Cu-SAPO-34-20催化剂具有最低的孤立Cu~(2+)还原温度以及最高的孤立Cu~(2+)含量.这可能有利于其NH3-SCR活性提高.同时H2-TPR还表明,H-Cu-SAPO-34催化剂中存在含量不等的孤立Cu+,并且孤立Cu~(2+)是NH3-SCR反应的主要活性中心.EPR测试结果进一步表明,位于SAPO-34椭球腔内(Site(I))的孤立Cu~(2+)是该反应的主要活性位.由NO的NH3-SCR反应测试结果来看,相比于普通的Cu/SAPO-34催化剂,具有丰富介孔结构的H-Cu-SAPO-34催化剂呈现出更高的低温催化活性,同时H-Cu-SAPO-34-20催化剂具有最高的低温NH3-SCR催化活性,这与其较高的活性Cu~(2+)含量以及较低的孤立Cu~(2+)还原温度密切相关.动力学测试结果表明,所合成的H-Cu-SAPO-34多级孔催化剂具有相似的活化能(Ea=98 kJ/mol),并且该值远大于普通CHA基SCR催化剂,这意味着介孔的存在确实大大降低了反应物分子在H-Cu-SAPO-34孔道内的扩散阻力,提高了反应物分子与活性位的接触概率,从而提高了其低温NH3-SCR催化性能.     

Bio-templated synthesis of highly ordered macro-mesoporous silica material for sustained drug delivery

The bimodal porous structured silica materials consisting of macropores with the diameter of 5–20 μm and framework-like mesopores with the diameter of 4.7–6.0 nm were prepared using natural Manchurian ash and mango linin as macropored hard templates and P123 as mesopore soft templates, respectively. The macroporous structures of Manchurian ash and mango linin were replicated with the walls containing highly ordered mesoporous silica as well. As-synthesized dual porous silica was characterized by scanning electron microscope (SEM), powder X-ray diffraction (XRD), transmission electron microscope (TEM) and nitrogen adsorption/desorption, fourier transform IR (FTIR) spectroscopy, and thermo-gravimetric analyzer (TGA). Ibuprofen (Ibu) was employed as a model drug and the release profiles showed that the dual porous material had a sustained drug delivery capability. And such highly ordered dual pore silica materials may have potential applications for bimolecular adsorption/separation and tissue repairing.     

Electrochemical study of o-toluidine blue impregnated in mesoporous silica channels

This paper reports an electrochemical study of ordered mesoporous silica impregnated with a cationic dye (o-toluidine blue), prepared with a non-ionic surfactant as the structure-directing agent. O-toluidine blue was chosen because of its utility as an electron transfer mediator (redox catalyst). O-toluidine blue impregnated mesoporous silica was characterized by nitrogen sorption porosimetry, small angle X-ray scattering, infrared spectroscopy, scanning electron microscopy and cyclic voltammetry using chemically modified carbon paste electrodes. Results indicate that the dye is located within the ordered mesopores of micron-sized silica spheres.     

萘普生在介孔分子筛MCM-41中的负载及其溶出性能

用含氨基的偶联剂修饰介孔分子筛MCM-41的表面,将修饰前和修饰后的介孔分子筛分别负载难溶性药物萘普生（NAP）,利用X射线衍射、傅里叶变换红外光谱、差示扫描量热分析、扫描电子显微镜、透射电子显微镜和N2吸附 脱附分析等技术分别对其进行了结构表征和性能测试。 结果表明,药物分子存在于分子筛的孔道中。 负载在MCM-41中的萘普生溶出速率远优于原料药,60 min时大约溶出70%。 氨基修饰后的药物释放速率比修饰前有所减慢,表明可通过氨基修饰调节释放速率。     

Preparation of Corn Stalk-Walnut Shell Mix-based Activated Carbon and Its Adsorption of Malachite Green

The mix-based activated carbon derived from corn stalk and walnut shell was prepared by chemical activation method using phosphoric acid as the activator. The optimized conditions for preparation were obtained by the orthogonal experiment, the characterizations of the activated carbon were performed by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy(FTIR), Boehm's titration method and nitrogen adsorption. For the prepared mix-based activated carbon, the highest iodine number, methylene blue number and BET surface area are 720.5 mg/g, 195.0 mg/g and 1187 m²/g, respectively, and the pores are mainly mesopores. The mix-based activated carbon shows the higher adsorption capacity for malachite green than the raw materials, the activated carbons prepared only from corn stalk or walnut shell and the commercial activated carbon. The kinetics and thermodynamics of the adsorption can be satisfactorily described by the pseudo-second-order kinetic model and the Langmuir isotherm model, separately.     

一种二维多孔窗口型膦酸锆材料的合成及其对不同金属离子的吸附性能

合成了一种二维窗口型膦酸锆材料β-丙氨酸-N,N-双亚甲基膦酸锆(ZrNCP),采用X射线衍射仪、扫描电镜、透射电镜分析了合成产物的相组成和微观结构;利用N2吸脱附试验装置测定了合成产物对不同金属离子的吸附性能,考察了浓度、温度及pH对其吸附性能的影响.结果表明,合成产物内部存在大量分布均匀的微介孔,材料微观形貌为规整片状.随着金属离子半径的增大,ZrNCP对各种金属离子的平衡吸附量(mmol/g)呈逐渐减小趋势.     

以花瓣为模板制备TiO2分层介孔纳米片

以月季花花瓣为模板, 经钛盐溶液浸渍后煅烧, 合成了新型TiO2 分层介孔纳米片. 采用X射线衍射(XRD)、 场发射扫描电子显微镜(FESEM)、 环境扫描电子显微镜(ESEM)、 透射电子显微镜(TEM)、 紫外-可见漫反射光谱(UV-Vis/DRS)和氮气吸附-脱附曲线分析等手段对样品进行了表征. 结果表明, 所得样品由厚度约4 nm的具有生物形态结构的锐钛矿型TiO2 纳米片组成. TiO2 薄层表面存在大量介孔, 其孔径集中分布于4 nm左右. 由紫外-可见漫反射吸收光谱可知, 材料的吸收边较纳米TiO2 (P25)红移了约20 nm, 因而具有更高的可见光光催化活性. TiO2 分层介孔纳米片在阳光下表现出较强的光催化活性, 在90 min内对亚甲基蓝的降解率可达98%, 远高于TiO2 纳米粉.     

Grafting of alumina on SBA-15: effect of surface roughness

Alumina-grafted materials were prepared by postsynthesis alumination of mesoporous SBA-15 silica in an aqueous solution of aluminum chlorhydrol. Prepared samples were characterized by nitrogen adsorption, scanning electron microscopy, X-ray powder diffraction, and (27)Al magic-angle-spinning NMR. The successive grafting of alumina on SBA-15 leads to a gradual filling of the corona surrounding the mesopores. As a consequence smoothing of the mesopore surface takes place. The in-depth analysis of nitrogen adsorption data proves that the alpha s method affords real values of the structure parameters, while the Kruk, Jaroniec, and Sayari (KJS) procedure based on the BJH algorithm provides only effective data corresponding to cylindrical mesopores of smooth geometrical surface. The quantification of the roughness of the SBA-15 mesopore surface based on the comparison of data obtained from the alpha s plot and KJS method was carried out.     

Iron monosulfide (FeS) oxidation by dissolved oxygen: characteristics of the product layer

Samples of FeS were oxidized by oxygen‐bearing acidic solutions at 25 °C and different initial pH values (2.75 ≤ pH ≤ 3.45). The reacted FeS samples were investigated by scanning electron microscopy (SEM), nitrogen adsorption/desorption isotherms measurements, and FT‐Raman spectroscopy. A sulfur rich phase (layer) is inferred to be form on reacting FeS surface based on sequential extraction with acidic chromium(II) chloride solutions. The sulfur‐rich layer (SRL) formed on oxidized FeS samples is traversed by various mesopores with average pore size < 450Å. It is reasonable to assume that the mesopores facilitate the migration of iron and sulfur from FeS structure into solution across SRL. The FT‐Raman spectra of oxidized FeS samples show an intense peak at 162 cm^?1, which can be attributed to SRL developed on FeS surface. A model for SRL development on FeS during its oxidation by dissolved oxygen has been proposed from the present results and previous studies. Copyright © 2009 John Wiley & Sons, Ltd.     

静电纺丝法制备交联多孔纳米碳纤维膜及其电化学电容性能

以聚丙烯腈(PAN)和三聚氰胺为原料,通过静电纺丝法制备了三聚氰胺改性聚丙烯腈纳米纤维前驱体,经预氧化、碳化后得到交联的多孔纳米碳纤维.采用红外光谱(FTIR)仪、热重分析(TGA)仪、扫描电子显微镜(SEM)、X射线衍射(XRD)仪、拉曼光谱仪和比表面积分析仪等对前驱体及纤维进行了表征.结果表明,经过三聚氰胺改性的聚丙烯腈纳米纤维前驱体在碳化后有效地交联,形成含有微孔、介孔和大孔多级的合理孔道结构,氮掺杂量高达14.3%,纤维直径大幅缩减,平均直径仅约89 nm.电化学测试结果表明,交联多孔纳米碳纤维电极在0.05 A·g^-1电流密度下未经活化时的质量比电容值高达194 F·g^-1(0.05 A·g^-1),在2 A·g^-1的电流密度下经过1000次循环充放电后的比电容仍然保持99.2%,表现出优异的电化学特性.     

Preparation of MCM-41 silica using the cationic surfactant blend

A series of samples of MCM-41 silica was synthesized using surfactant blends of 1-alkyl-3-methylimidazolium and alkyltrimethylammonium salts or blends of two different 1-alkyl-3-methylimidazolium salts (alkyl denotes octyl or hexadecyl) as structure-directing agents. The precipitation of solid particles from a homogeneous water solution of sodium metasilicate and surfactant blend was achieved by lowering the pH due to the hydrolysis of ethyl acetate added. The molecular sieves were characterized by scanning as well as transmission electron microscopy, X-ray powder diffraction, and nitrogen adsorption using a proper nonlocal density functional theory approach for calculations of the textural parameters. All the prepared silicas were of MCM-41-type; they differ in the integral breadth of the pore size distribution curve and the presence of secondary mesopores. The best quality MCM-41 silica of spherical particle morphology was synthesized by using of optimized blend of hexadecyltrimethylammonium bromide and 1-methyl-3-octylimidazolium chloride. The results obtained showed that spherical particles are composed of domains of perfectly ordered hexagonal porous structure. Some samples prepared by using 1-alkyl-3-methylimidazolium salts featured a narrow pore size distribution. However, they contained a small volume of secondary mesopores.     

Textural and adsorption properties of mesoporous silicophosphate

Low-temperature nitrogen adsorption-desorption and electron microscopy are employed to investigate the textural and adsorption properties of a silicophosphate material produced by the sol-gel method under the influence of two factors, pH of the sol-gel transition and the presence of a template, which predetermine the physical characteristics of the material. It is shown that the mesoporous structure of silicophosphate is composed of rather uniform bottle-shaped mesopores with necks the average diameter of which can be regulated in a targeted fashion in a narrow range of 3–5 nm. Templation with cetylpyridinium chloride leads to flattening the amorphous walls of the pores in silicophosphate and the formation of mesopores with large average diameters. The features of the supramolecular structure, which are revealed at different scale levels by electron microscopy and the analysis of the external and internal surface areas of silicophosphate, are not reflected in the pore-size distribution curves calculated from sorption isotherms, because they are governed by the interconnection of the mesopores rather than their individual shapes.     

Fabrication of hierarchically porous silica nanospheres through sol–gel process and pseudomorphic transformation

Hierarchically porous silica nanospheres with well-defined morphology and uniform particle size had been synthesized through a multistep sol–gel method combined with pseudomorphic transformation in the presence of polyvinylpyrrolidone (PVP) and cetyltrimethylammoium bromide (CTAB) as dual template. The prepared materials were characterized by small-angle X-ray diffraction, transmission electron microscopy, scanning electron microscopy, and nitrogen physical adsorption techniques. The preparation process and the origin of hierarchical structure were also investigated. It had been shown that the hierarchical structure of synthesized materials comprises wormlike framework mesopores with diameters of about 3 nm and bubble-like pores with diameters of 20–30 nm. CTAB and PVP behave as dual-template and are responsible for the formation of the mesopores and big pores, respectively. Not only the porous structure, but also the morphology and particle size of hierarchical materials can be adjusted by controlling the addition of PVP. In addition, the formation process of hierarchically porous silica was investigated by transmission electron microscopy, FT-IR spectra and thermo-gravimetric curves and a possible synthetic mechanism had been proposed.     

有序介孔二氧化硅对正丁醛的吸附性能

合成了一系列具有不同孔结构与性质的有序介孔二氧化硅材料SBA-15、MCM-41、SBA-16、KIT-6, 同时通过改变水热温度制备了不同孔径大小的SBA-15, 并利用小角X射线散射、透射电镜、扫描电镜和氮气吸附-脱附等手段, 对其介孔结构进行了表征. 以正丁醛为探针分子, 考察了其对有机醛的吸附, 并与Y-沸石的吸附性能做了对比. 结果表明, 材料的介孔比表面积与其对正丁醛的吸附量成正比, 吸附等温线符合Langmuir 模型, 属于单层吸附, 具有最大介孔比表面积的MCM-41对正丁醛的吸附量最大(484 mg·g^-1). 最后将SBA-15添加到卷烟滤嘴中, 实验结果表明, SBA-15能显著降低卷烟烟气中巴豆醛的释放量.