采用碳化-沉淀法制备纤维状纳米Mg（OH）2的研究

本文以轻烧白云石粉料为原料,用碳化法制备出碱式碳酸镁,酸化后以氨水作为沉淀剂,用化学沉淀法制得Mg（OH）₂,用乙二胺对制得的Mg（OH）₂进行后处理,制得纤维状纳米Mg（OH）₂。用SEM、XRD和TG-DTA对制得的Mg（OH）₂进行表征。XRD结果表明再结晶温度180℃以上可以得到具有完整晶体结构的Mg（OH）₂。SEM结果显示Mg（OH）₂颗粒的尺寸随着乙二胺加入量的增大而增大。当Mg（OH）₂的再结晶时间超过21h后,可以得到直径20~30nm,长度400~700nm的纤维状Mg（OH）₂。TG-DTA表明Mg（OH）₂在318~416℃分解为MgO。     

层状氢氧化苯甲酸锌的水热合成与表征

在110～180 ℃范围内, 以Zn(OH)2与苯甲酸为原料水热法成功合成了层状氢氧化苯甲酸锌化合物. 通过XRD、TG-DTA、SEM、TEM和元素分析研究了合成产物的结构、形貌、性质和化学组成, 探讨了合成条件对水热反应产物的影响. 当C6H5COOH/Zn的摩尔比为0.9～1.0, 水热温度130～150 ℃及水热反应12 h, 合成的层状化合物具有纤维状粒子特征, 层间距为1.44 nm, 化学组成为Zn(OH)1.12•(C6H5COO)0.88.     

层间距为1.44 nm层状氢氧化苯甲酸锌剥离重组行为研究

层间距为1.44 nm层状氢氧化苯甲酸锌在乙醇、正丙醇、正丁醇介质中可剥离成其基本组成单元纳米层. 用TG-DTA、XRD、SEM、TEM和元素分析等手段研究了剥离的纳米层重组得到样品的结构特征、形貌和化学组成. 结果表明: 水热合成样品和剥离的纳米层重组样品具有相同的层状结构, 它们的化学组成分别为Zn(OH)1.12(C6H5COO)0.88和Zn(OH)1.1(C6H5COO)0.9. 水热合成的纤维状粒子剥离重组后改变成为像纳米带和纳米花粒子形貌.     

氢氧化镁纳米片的合成及其润滑性能的研究

以硫酸镁和氢氧化钠为原料,油酸为表面修饰剂,采用原位合成的方法制备出了疏水性的Mg(OH2)纳米片.研究了反应温度、反应物浓度等因素对氢氧化镁纳米片平均粒径的影响.用X-射线粉末衍射(XRD)、红外(IR)和热重(DTA-TGA)及扫描电子显微镜(SEM),对制备出的Mg(OH)2纳米片的结构和形貌进行了表征,证实制备出的Mg(OH)2纳米片具有良好分散性,纳米片尺度为200～300nm,厚度10nm.摩擦实验证明Mg(OH2)纳米片可以作为润滑油中的添加剂来应用.     

纳米MgBO_2(OH):Eu~(3+)的制备及发光性能研究

利用水热法,制备得到了纳米线组装的绒球状和纳米带聚集的絮状Mg BO2(OH):Eu3+,对它们进行了EDS、XRD、IR、SEM等表征及发光性能研究。研究发现两个产品的最高激发峰和发射峰分别都位于λ=250nm和λ=615nm处,为红色发光材料;且发现绒球状Mg BO2(OH):Eu3+的峰强度明显强于絮状Mg BO2(OH):Eu3+,但絮状Mg BO2(OH):Eu3+的红橙比(R/O)更高。     

静电纺丝法制备Y2O3纳米纤维与表征

采用静电纺丝法制备了PVA/Y(NO3)3复合纳米纤维,在适当的温度下进行热处理,得到Y2O3纳米纤维. 利用XRD,SEM,TG-DTA,FTIR等现代分析手段对样品进行了表征. XRD分析表明,PVA/Y(NO3)3复合纤维为无定型,焙烧温度在600 ℃以上得到晶态单相的Y2O3纳米纤维,属于立方晶系,空间群为Ia3. SEM分析表明,PVA/Y(NO3)3复合纤维表面光滑,平均直径为110 nm. 焙烧温度对Y2O3纳米纤维的形成有重要影响. 600 ℃焙烧得到的Y2O3纳米纤维的平均直径约50 nm,900 ℃焙烧得到的Y2O3纳米纤维由纳米颗粒堆积而成,部分已断裂. TG-DTA和FTIR分析表明,PVA,Y(NO3)3以及水分在600 ℃以上时完全分解挥发,最终样品为晶态单相的Y2O3纳米纤维.     

在乙二醇溶液中合成复合金属醇盐和纳米NiFe2O4

在乙二醇溶液中用电化学法制备了镍、铁醇盐配合物NiFe2(OCH2CH2OH)8,将其溶液水解、真空干燥后在400℃煅烧2 h,得到纳米级NiFe2O4粉体.产物NiFe2(OCH2CH2OH)8通过红外光谱(FTIR)和拉曼光谱(Raman)进行表征,纳米NiFe2O4通过X射线粉末衍射(XRD)和电子显微镜(TEM、SEM)进行表征.实验表明,前驱体中含有OCH2CH2OH基团,可以有效克服水解与煅烧过程中的团聚现象,经400 ℃煅烧2 h得到的纳米NiFe2O4粉体,颗粒分散较好、纯度高,粒径在25～40 nm.     

纳米Cu(OH)2分解温度对CuO粒度的影响

以CuSO4.5H2O和NaOH为原料,采用沉淀法制备得到Cu(OH)2纤维,再进行Cu(OH)2的分解反应.考察了在不同实验条件下温度对Cu(OH)2热分解过程的影响.结果表明:在反应温度20℃,反应终点pH值为12,搅拌速度为1 200 r.min-1,NaOH溶液的滴加速度为50 mL.min-1的反应条件下,得到的样品为纳米Cu(OH)2纤维,其直径为10~30 nm、长度为1~6μm;在固相纳米Cu(OH)2热分解制备CuO过程中CuO粒径随温度的升高而增大,在温度不超过200℃时CuO的粒径约为20 nm左右;在液相中先沉淀后升温时,产物的形貌为球形,CuO粒径随温度的升高而增大,低于80℃可得到纳米级的CuO.     

静电纺丝制备YVO4:Sm3+纳米纤维及其荧光光谱性能

采用静电纺丝技术与高温煅烧工艺相结合,以氧化钐、氧化钇、偏钒酸铵和聚丙烯腈为主要原料,制备稀土离子掺杂的YVO4:Sm3+纳米纤维。利用X射线衍射(XRD)、扫描电子显微镜(SEM)、傅立叶变换红外(FT-IR)、热重-差热(TG-DTA)和荧光光谱(PL)等分析测试手段对所得样品的结构、形貌和荧光光谱性能进行表征。研究结果表明:静电纺丝制备的有机-无机复合纤维的直径在200~250 nm之间,经过900℃热处理后,所得YVO4:Sm3+样品纤维状结构保持完好,直径减至100 nm。掺杂的稀土Sm3+离子在YVO4纤维中显示出特征发射,同时VO3-4和稀土Sm3+离子之间存在能量传递;Sm3+的掺杂浓度为2%(摩尔分数)时发光强度最大。     

不同粒径氧化铜的制备及其氢还原动力学研究

以CuSO4.5H2O和NaOH为原料制备0.1mol·L-1CuSO4溶液和4mol·L-1NaOH溶液,采用沉淀法制备Cu(OH)2纳米粉末,然后分别在200℃,500℃,900℃温度下分解Cu(OH)2得到不同粒度的氧化铜粉体.在氢气中,以15℃.min-1升温速率,用SDT2960Simulta-neousDSC-TGA差热-热重分析仪测定TG-DTA曲线,并进行动力学计算.结果表明:氧化铜粉体的形貌近似为球形,粒径分别为50,150,400nm;DTA峰值温度分别为258.90℃,279.17℃,364.80℃,随粒径的增大而提高;表观活化能分别为173.39,461.54,534.80kJ·mol-1,随粒径的增大而增大;频率因子分别为1.15×1018,2.49×1045,2.54×1045,随粒径的增大而增大;反应级数分别为1.16,1.15,1.03,随粒径的增大而减少.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.