应用小干扰柱体控制角区马蹄涡结构的实验研究

本文提出一种简单的抑制和控制角区马蹄涡的被动控制方法.即在角区平板上游放置一个远小于主柱体的小干扰柱体,用其产生的弱马蹄涡来抑制和控制角区的马蹄涡结构.目的是使角区原来的马蹄涡结构由强变为弱、由大变为小、由多变为少、由非定常变为定常,以获得减小冲刷、抑制湍流、降低噪声、避免振动的工程效果.作者在风洞中采用烟线法和激光片光流动显示的方法开展研究,实验表明,在平板上游适当位置放置小干扰柱体的确可以有效抑制和控制角区马蹄涡结构.实验发现,当小干扰柱体放置在原角区马蹄涡生成区时,其抑制和控制效果最佳;当小干扰柱体放置在上游区或下游区时,控制效果不好.本文讨论了小干扰柱体控制角区马蹄涡的机理.此外,实验还研究了小干扰柱体相对尺度和截面形状对角区马蹄涡结构抑制和控制的影响.     

双柱单锥型液-液旋流管内流场的激光诊断

应用激光测速仪，对一种双柱单锥型液 液旋流管内的流动结构，进行了全场范围内的多工况流动诊断研究．揭示出其切向速度由内旋流区和外旋流区构成，其中内旋流区中的速度分布符合准强制涡关系，外旋流区中的速度分布符合准自由涡关系；轴向速度由上行流动区和下行流动区构成，两者之间在直管段以零速点作分界，在锥体段则以零速区作过渡并伴随有一定的回流出现，且该过渡区或回流区的大小随锥体截面的收缩而减小，直到进入直管段后消失；各湍流量的分布以管芯处最大向外逐渐减小，沿轴向是直管段中的湍流度大于锥体段中的湍流度，而且湍流度在旋流管内具有各向异性的特性．     

Phase-resolved characterization of vortex shedding in the near wake of a square-section cylinder at incidence

The vortex formation and shedding process in the near wake region of a 2D square-section cylinder at incidence has been investigated by means of particle image velocimetry (PIV). Proper orthogonal decomposition (POD) is used to characterize the coherent large-scale flow unsteadiness that is associated with the wake vortex shedding process. A particular application of the POD analysis is to extract the vortex-shedding phase of individual velocity fields, which were acquired at asynchronous low rate with respect to the vortex shedding cycle. The phase of an individual flow field is determined from its projection on the first pair of POD modes, allowing phase averaging of the measurement data to be performed. In addition, a low-order representation of the flow, constructed from the mean and the first pair of POD modes, is found to be practically equivalent to the phase-averaged results. It is shown that this low-order representation corresponds to the basic Fourier component of the flow field ensemble with respect to the reconstructed phase. The phase-averaged flow representations reveal the dominant flow features of the vortex-shedding process and the effect of the angle of incidence upon it.     

Experimental study on aerodynamic coefficients of yawed cylinders

This paper presents wind tunnel tests on a stationary cylinder inclined with the flow. The cylinder was positioned at different sets of yaw and vertical angles. The flow regime of the tests remained in the subcritical state. Two load cells were designed and installed to measure the aerodynamic forces, with enough sensitivity to measure vortex shedding frequencies. In this paper, the three aerodynamic force coefficients are normalized using the free stream velocity instead of its normal component. The results show that the drag coefficient and the resultant of the lift and side forces coefficients can be described by an empirical function of the incidence angle. The lift and side force coefficients remain however functions of both the horizontal yaw and vertical angles and cannot be expressed as functions of the incidence angle only. The Independence Principle was observed to become inaccurate for yaw angles larger than 40°. However, the measured Strouhal numbers indicate that the vortex shedding frequencies of a yawed cylinder can be predicted using the Independence Principle.     

Specified discharge velocity models for numerical simulations of laminar vortex rings

We numerically and theoretically investigate the flow generated at the exit section of a piston/cylinder arrangement that is generally used in experiments to produce vortex rings. Accurate models for the velocity profile in this section (also called specified discharge velocity, SDV models) are necessary in (i) numerical simulations of laminar vortex rings that do not compute the flow inside the cylinder and (ii) in slug-models that provide a formula for the total circulation of the flow. Based on the theoretical and numerical analysis of the flow evolution in the entrance region of a pipe, we derive two new and easy to implement SDV models. A first model takes into account the unsteady evolution of the centerline velocity, while the second model also includes the time variation of the characteristics of the boundary layer at the exit plane of the vortex generator. The models are tested in axisymmetric direct numerical simulations of vortex rings. As distinguished from classical SDV model, the new models allow to accurately reproduce the characteristics of the flow. In particular, the time evolution of the total circulation is in good agreement with experimental results and previous numerical simulations including the vortex generator. The second model also provides a more realistic time evolution of the vortex ring circulation. Using the classical slug-model and the new correction for the centerline velocity, we finally derive a new and accurate analytical expression for the total circulation of the flow.     

Time-averaged topological flow patterns and their influence on vortex shedding of a square cylinder in crossflow at incidence

Flow characteristics around the square cylinder and their influence on the wake properties are studied. Time-averaged flow patterns on the surfaces of square cylinder in a cross-stream at incidence are experimentally probed by surface-oil flow technique and analyzed by flow topology for Reynolds numbers between 3.9×10⁴ and 9.4×10⁴ as the incidence angle changes from 0° to 45°. Vortex shedding characteristics are measured by a single-wire hot-wire anemometer for Reynolds numbers between 5×10³ and 1.2×10⁵. The effects of topological flow patterns on the wake properties then are revealed and discussed. Flows around the square cylinder are identified as three categories: the subcritical, supercritical, and wedge flows according to the prominently different features of the topological flow patterns. The Strouhal number of vortex shedding, turbulence in the wake, and wake width present drastically different behaviors in different characteristic flow regimes. A critical incidence angle of 15° separates the subcritical and supercritical regimes. At the critical incidence angle the wake width and shear-layer turbulence present minimum values. The minimum wake width appearing at the critical incidence angle, which leads to the maximum Strouhal number, is due to the reattachment of one of the separated boundary layer to the lateral face of the square cylinder. If the Strouhal numbers are calculated based on the wake width instead of the cross-stream projection width of cylinder, the data in the subcritical and supercritical regimes are well correlated into two groups, which would approach constants at high Reynolds numbers.     

The effect of vortex angle on the efficiency of the Ranque–Hilsch vortex tube

A Ranque–Hilsch vortex tube is a long hollow cylinder with tangential nozzle placed near one end for injection of compressed air. The flow inside the vortex tube can be described as rotating air, which moves as a helical vortex flow. The peripheral flow moves toward the hot end, where the central part of the tube is blocked by a plug. The axial flow, which is forced back by the central part of the hot end plug, moves in the opposite direction toward the cold end. This paper focuses on the effect of the angle of rotating flow on the performance and efficiency of the Ranque–Hilsch vortex tube. To find the effect of vortex angle, different vortex angle generators were used and the best configuration was found.     

Experimental investigation of the flow-induced vibration of a curved cylinder in convex and concave configurations

Experiments have been conducted to investigate the two-degree-of-freedom vortex-induced vibration (VIV) response of a rigid section of a curved circular cylinder with low mass-damping ratio. Two curved configurations, a concave and a convex, were tested regarding the direction of the flow, in addition to a straight cylinder that served as reference. Amplitude and frequency responses are presented versus reduced velocity for a Reynolds number range between 750 and 15 000. Results for the curved cylinders with concave and convex configurations revealed significantly lower vibration amplitudes when compared to the typical VIV response of a straight cylinder. However, the concave cylinder showed relatively higher amplitudes than the convex cylinder which were sustained beyond the typical synchronisation region. We believe this distinct behaviour between the convex and the concave configurations is related to the wake interference taking place in the lower half of the curvature due to perturbations generated in the horizontal section when it is positioned upstream. Particle-image velocimetry (PIV) measurements of the separated flow along the cylinder highlight the effect of curvature on vortex formation and excitation revealing a complex fluid–structure interaction mechanism.     

Flow around four cylinders arranged in a square configuration

This paper presents an experimental study of the flow around four circular cylinders arranged in a square configuration. The Reynolds number was fixed at Re=8000, the pitch-to-diameter ratio between adjacent cylinders was varied from P/D=2 to 5 and the incidence angle was changed from α=0° (in-line square configuration) to 45° (diamond configuration) at an interval of 7.5°. The flow field was measured using digital Particle Image Velocimetry (PIV) to examine the vortex shedding characteristics of the cylinders, together with direct measurement of fluid dynamic forces (lift and drag) on each cylinder using a piezoelectric load cell. Depending on the pitch ratio, the flow could be broadly classified as shielding regime (P/D≤2), shear layer reattachment regime (2.5≤P/D≤3.5) and vortex impinging regime (P/D≥4). However, this classification is valid only in the case that the cylinder array is arranged nearly in-line with the free stream (α≈0°), because the flow is also sensitive to α. As α increases from 0° to 45°, each cylinder experiences a transition of vortex shedding pattern from a one-frequency mode to a two-frequency mode. The flow interference among the cylinders is complicated, which could be non-synchronous, quasi-periodic or synchronized with a definite phase relationship with other cylinders depending on the combined value of α and P/D. The change in vortex pattern is also reflected by some integral parameters of the flow such as force coefficients, power spectra and Strouhal numbers.     

虚拟边界法研究正交双圆柱及串列双圆球绕流

把Goldstein等人提出的虚拟边界法推广到三维情况,研究了 Re=150时不同间距下正交双圆柱绕流,和Re=250时不同间距下串列双 圆球绕流流场. 对于正交双圆柱绕流,当间距比大于3,下游圆柱对上游圆柱尾流的影响只 限定在下游圆柱的尾流所扫过的范围之内;当间距比小于等于3,下游圆柱对上游圆柱尾流 的影响扩大,下游圆柱尾流扫过区上下出现两排三维流向二次涡结构. 对于串列圆球绕流, 研究发现,在小间距比(L/D≈ 1.5)的情况下,由于上下游圆球尾流区的相互抑 制消除了压力不稳定性,整个流场呈现稳 态轴对称特征;间距比为2.0时,周向压力梯度诱发出流体的周向输运,流场呈现稳态非对 称性,但流场中存在特定的对称面;间距比增大到2.5后,绕流场开始周期振荡,原有的对 称面依旧存在;在间距比3.5时下游圆球下表面的涡结构强度有所减弱,导致占优频率发生 交替;间距比增至7.0时,整个流场恢复稳态特征,两圆球尾部同时出现双线涡,这时流场 对称面的位置发生了变动.     

Roughness and turbulence intensity effects on the induced flow oscillation of a single cylinder

The effects of the surface roughness and the turbulence intensity on the dynamic characteristics of the flow induced oscillations of an elastically supported single circular cylinder in a cross flow in the vortex shedding and fluid elastic regions were experimentally investigated. The results of these experiments indicate that, for the vortex shedding region, increasing the surface roughness results in a reduction of the amplitude of oscillation, while in the fluid elastic region, increasing the surface roughness tends to enhance the oscillations. A similar trend for the dynamic response of the cylinder in the vortex shedding region was also observed when the free stream turbulence intensity was varied, while in the fluid elastic region variations in the free stream turbulence intensity were observed to have no drastic effect on the dynamic response of the cylinder.     

Roughness and turbulence intensity effects on the induced flow oscillation of a single cylinder

The effects of the surface roughness and the turbulence intensity on the dynamic characteristics of the flow induced oscillations of an elastically supported single circular cylinder in a cross flow in the vortex shedding and fluid elastic regions were experimentally investigated. The results of these experiments indicate that, for the vortex shedding region, increasing the surface roughness results in a reduction of the amplitude of oscillation, while in the fluid elastic region, increasing the surface roughness tends to enhance the oscillations. A similar trend for the dynamic response of the cylinder in the vortex shedding region was also observed when the free stream turbulence intensity was varied, while in the fluid elastic region variations in the free stream turbulence intensity were observed to have no drastic effect on the dynamic response of the cylinder.     

Laminar boundary layer in a flow past an aerofoil with a circular cavity

The paper describes a numerical study of a method of preventing the separation of a laminar boundary layer from the forward section of a symmetric aerofoil, the flow past which does not separate at zero angle of incidence. In order to increase the maximum angle of incidence at which the flow has still not separated, a circular cavity (vortex cell) located almost completely inside the aerofoil is introduced on the segment vulnerable to separation. The asymptotics of the corresponding flow at high Reynolds number are described using the Prandtl-Batchelor model. Krasnodar. Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No. 2, pp. 52–57, March–April, 1998. The work was financially supported by the International Science Foundation (grants M4K000 and M4K300) and by the Russian Foundation for Fundamental Research (project No. 96-01-01290).     

PIV measurements of flow past a confined cylinder

This study investigates the flow past a confined circular cylinder built into a narrow rectangular duct with a Reynolds number range of 1,500 ≤ Re _d ≤ 6,150, by employing the particle image velocimetry technique. In order to better explain the 3-D flow behaviour in the juncture regions of the lower and upper plates and the cylinder, respectively, as well as the dynamics of the horseshoe vortex system, both time-averaged and instantaneous flow data are presented for regions upstream and downstream of the cylinder. The size, intensity and interaction of the vortex systems vary substantially with the Reynolds number. Although the narrow rectangular duct with a single built-in cylinder is a geometrically symmetrical arrrangement, instantaneous flow data have revealed that the flow structures in both the lower and upper plate–cylinder junction regions are not symmetrical with respect to the centreline of the flow passage. The vortical flow structures obtained in side-view planes become dominant sometimes in the lower juncture region and sometimes in the upper juncture region in unsteady mode.     

Global aerodynamic instability of twin cylinders in cross flow

This paper comprises an in-depth physical discussion of the flow-induced vibration of two circular cylinders in view of the time-mean lift force on stationary cylinders and interaction mechanisms. The gap-spacing ratio T/D is varied from 0.1 to 5 and the attack angle α from 0° to 180° where T is the gap width between the cylinders and D is the diameter of a cylinder. Mechanisms of interaction between two cylinders are discussed based on time-mean lift, fluctuating lift, flow structures and flow-induced responses. The whole regime is classified into seven interaction regimes, i.e., no interaction regime; boundary layer and cylinder interaction regime; shear-layer/wake and cylinder interaction regime; shear-layer and shear-layer interaction regime; vortex and cylinder interaction regime; vortex and shear-layer interaction regime; and vortex and vortex interaction regime. Though a single non-interfering circular cylinder does not correspond to a galloping following quasi-steady galloping theory, two circular cylinders experience violent galloping vibration due to shear-layer/wake and cylinder interaction as well as boundary layer and cylinder interaction. A larger magnitude of fluctuating lift communicates to a larger amplitude vortex excitation.     

钝体尾流控制机理及方法研究进展

首先从涡脱落生成理论出发对钝体尾流控制方法进行了分类,并简单介绍了国内尾流控制研究情况. 之后介绍了我们用窄条或小方柱取代小圆柱后,对Strykowsky和Sreenivasan 控制方法的改进及其在高雷诺数下对圆柱和方柱尾流涡脱落的有效抑制情况, 并探讨了控制件钝度对抑制效果的影响.第3部分用实验数据对各个涡脱落生成模型做了分析与检验, 指出控制件方法的机理与改变钝体分离位置、减小钝体背压吸力、改变流动的展向相关性、 防止钝体两侧剪切层相互作用等无关,而与钝体近尾流速度剖面的局部修正及其稳定性的改变有关. 最后简单介绍了控制件方法今后研究工作展望及其工程应用前景.     

Combined action of transverse oscillations and uniform cross-flow on vortex formation and pattern of a circular cylinder

This paper attempts to study the roles of lateral cylinder oscillations and a uniform cross-flow in the vortex formation and wake modes of an oscillating circular cylinder. A circular cylinder is given lateral oscillations of varying amplitudes (between 0.28 and 1.42 cylinder-diameters) in a slow uniform flow stream (Reynolds number=284) to produce the 2S, 2P and P+S wake modes. Detailed flow information is obtained with time-resolved particle-image velocimetry and the phase-locked averaging techniques. In the 2S and 2P mode, the flow speeds relative to the cylinder movement are less than the uniform flow velocity and it is found that initial formation of a vortex is caused by shear-layer separation of the uniform flow on the cylinder. Subsequent development of the shear-layer vortices is affected by the lateral cylinder movement. At small cylinder oscillation amplitudes, vortices are shed in synchronization with the cylinder movement, resulting in the 2S mode. The 2P mode occurs at larger cylinder oscillation amplitudes at which each shear-layer vortex is found to undergo intense stretching and eventual bifurcation into two separate vortices. The P+S mode occurs when the cylinder moving speeds are, for most of the time, higher than the speed of the uniform flow. These situations are found at fast and large-amplitude cylinder oscillations in which the flow relative to the cylinder movement takes over the uniform flow in governing the initial vortex formation. The formation stages of vortices from the cylinder are found to bear close resemblance to those of a vortex street pattern of a cylinder oscillating in an otherwise quiescent fluid at Keulegan–Carpenter numbers around 16. Vortices in the inclined vortex street pattern so formed are then convected downstream by the uniform flow as the vortex pairs in the 2P mode.     

旋转圆柱绕流流场特性分析

对雷诺数Re = 20000 ~ 90000、相对转速ɑ = 0 ~ 0.72的旋转圆柱后方流场进行了实验测量, 分析了旋转圆柱后方不同剖面处的速度分布规律和湍流度分布规律. 采用LES方法对旋转圆柱绕流问题进行了数值模拟, 分析旋转圆柱周围流场特性和自由剪切层变化规律, 最后通过理论模型对流场变化进行分析, 得出如下结论: 当圆柱逆时针旋转时, 同一雷诺数下随着相对转速的增加, 旋转圆柱尾迹区域下方速度突变处的位置随着相对转速的增加而上移, 而上方速度突变处的位置不变, 雷诺数的增加使旋转圆柱尾迹区域下方速度突变处位置有小幅度的下移. 通过数值模拟发现, 圆柱旋转之后, 圆柱后方下侧涡的位置明显上移, 且幅度较大. 下方的自由剪切层有明显的上移, 上方的自由剪切层位置变化较小. 最后通过理论分析发现, 圆柱后侧下方涡位置的上移对圆柱升力影响十分显著, 在高雷诺数、低相对转速的条件下, 旋转圆柱后侧下方涡位置的改变对旋转圆柱的升力、尾流区自由剪切层的变化起到了重要的影响.      

Wake flow pattern modified by small control cylinders at low Reynolds number

Passive wake control behind a circular cylinder in uniform flow is studied by numerical simulation for Re_D ranging from 80 to 300. Two small control cylinders, with diameter d/D=1/8, are placed at x/D=0.5 and y/D=±0.6. Unlike the 1990 results of Strykowski and Sreenivasan, in the present study, the vortex street behind the main cylinder still exists but the fluctuating lift and the form drag on the main cylinder reduces significantly and monotonously as the Reynolds number increases from 80 to 300. Obstruction of the control cylinders to the incoming flow deflects part of the fluid to pass through the gap between the main and control cylinders, forming two symmetric streams. These streams not only eliminate the flow separation along the rear surface of the main cylinder, they also merge toward the wake centerline to create an advancing momentum in the immediate near-wake region. These two effects significantly reduce the wake width behind the main cylinder and lead to monotonous decrease of the form drag as the Reynolds number increases. As the Reynolds number gets higher, a large amount of the downstream advancing momentum significantly delays the vortex formation farther downstream, leading to a more symmetric flow structure in the near-wake region of the main cylinder. As the Reynolds number increases from 80 to 300, both increasing symmetry of the flow structure in the near-wake and significant delay of the vortex formation are the main reasons for the fluctuating lift to decrease monotonously.     

Flow regimes and frequency selection of a cylinder oscillating in an upstream cylinder wake

This paper describes flow around a pair of cylinders in tandem arrangement with a downstream cylinder being fixed or forced to oscillate transversely. A sinusoidal parietal velocity is applied to simulate cylinder oscillation. Time-dependent Navier-Stokes equations are solved using finite element method. It is shown that there exist two distinct flow regimes: ‘vortex suppression regime’ and ‘vortex formation regime’. Averaged vortex lengths between the two cylinders, pressure variations at back and front stagnant points as well as circumferential pressure profiles of the downstream cylinder are found completely different in the two regimes and, thus, can be used to identify the flow regimes. It is shown that frequency selection in the wake of the oscillating cylinder is a result of non-linear interaction among vortex wakes upstream and downstream of the second cylinder and its forced oscillation. Increasing cylinder spacing results in a stronger oscillatory incident flow upstream of the second cylinder and, thus, a smaller synchronization zone.