Improving the balance of carrier mobilities of host-guest solid-state light-emitting electrochemical cells

We report efficient host-guest solid-state light-emitting electrochemical cells (LECs) utilizing a cationic terfluorene derivative as the host and a red-emitting cationic transition metal complex as the guest. Carrier trapping induced by the energy offset in the lowest unoccupied molecular orbital (LUMO) levels between the host and the guest impedes electron transport in the host-guest films and thus improves the balance of carrier mobilities of the host films intrinsically exhibiting electron preferred transporting characteristics. Photoluminescence measurements show efficient energy transfer in this host-guest system and thus ensure predominant guest emission at low guest concentrations, rendering significantly reduced self-quenching of guest molecules. EL measurements show that the peak EQE (power efficiency) of the host-guest LECs reaches 3.62% (7.36 lm W(-1)), which approaches the upper limit that one would expect from the photoluminescence quantum yield of the emissive layer (～0.2) and an optical out-coupling efficiency of ～20% and consequently indicates superior balance of carrier mobilities in such a host-guest emissive layer. These results are among the highest reported for red-emitting LECs and thus confirm that in addition to reducing self-quenching of guest molecules, the strategy of utilizing a carrier transporting host doped with a proper carrier trapping guest would improve balance of carrier mobilities in the host-guest emissive layer, offering an effective approach for optimizing device efficiencies of LECs.     

The efficiency of light-emitting electrochemical cells

We report on the efficiency behavior of light-emitting electrochemical cells (LECs) fabricated from a methyl-substituted ladder-type poly(p-phenylene) (mLPPP) that was blended with a crown ether based solid state electrolyte. Unlike organic light-emitting diodes (oLEDs) utilizing mLPPP as an active layer, the LECs suffer from a loss of efficiency at elevated current densities. From scan rate dependent studies we deduce that this efficiency drop is not only due to device decomposition upon high voltage operation and we also reveal the intrinsic mode of LEC operation. The decreasing width of the intrinsic region between the p- and n-type doped zones upon ongoing pin-junction formation causes distinct (either field or electrode induced) luminance quenching effects.     

Phosphorescent sensitized fluorescent solid-state near-infrared light-emitting electrochemical cells

We report phosphorescent sensitized fluorescent near-infrared (NIR) light-emitting electrochemical cells (LECs) utilizing a phosphorescent cationic transition metal complex [Ir(ppy)(2)(dasb)](+)(PF(6)(-)) (where ppy is 2-phenylpyridine and dasb is 4,5-diaza-9,9'-spirobifluorene) as the host and two fluorescent ionic NIR emitting dyes 3,3'-diethyl-2,2'-oxathiacarbocyanine iodide (DOTCI) and 3,3'-diethylthiatricarbocyanine iodide (DTTCI) as the guests. Photoluminescence measurements show that the host-guest films containing low guest concentrations effectively quench host emission due to efficient host-guest energy transfer. Electroluminescence (EL) measurements reveal that the EL spectra of the NIR LECs doped with DOTCI and DTTCI center at ca. 730 and 810 nm, respectively. Moreover, the DOTCI and DTTCI doped NIR LECs achieve peak EQE (power efficiency) up to 0.80% (5.65 mW W(-1)) and 1.24% (7.84 mW W(-1)), respectively. The device efficiencies achieved are among the highest reported for NIR LECs and thus confirm that phosphorescent sensitized fluorescence is useful for achieving efficient NIR LECs.     

Near-quantitative internal quantum efficiency in a light-emitting electrochemical cell

A green-light-emitting iridium(III) complex was prepared that has a photoluminescence quantum yield in a thin-film configuration of almost unity. When used in a simple solid-state single-layer light-emitting electrochemical cell, it yielded an external quantum efficiency of nearly 15% and a power efficiency of 38 Lm/W. We argue that these high external efficiencies are only possible if near-quantitative internal electron-to-photon conversion occurs. This shows that the limiting factor for the efficiency of these devices is the photoluminescence quantum yield in a solid film configuration. The observed efficiencies show the prospect of these simple electroluminescent devices for lighting and signage applications.     

Identifying and alleviating electrochemical side-reactions in light-emitting electrochemical cells

We demonstrate that electrochemical side-reactions involving the electrolyte can be a significant and undesired feature in light-emitting electrochemical cells (LECs). By direct optical probing of planar LECs, comprising Au electrodes and an active material mixture of {poly[2-methoxy-5-(2-ethylhexyloxy)-1,4-phenylenevinylene] (MEH-PPV) + poly(ethylene oxide) (PEO) + KCF3SO3}, we show that two direct consequences of such a side-reaction are the appearance of a "degradation layer" at the negative cathode and the formation of the light-emitting p-n junction in close proximity to the cathode. We further demonstrate that a high initial drive voltage and a high ionic conductivity of the active material strongly alleviate the extent of the side reaction, as evidenced by the formation of a relatively centered p-n junction, and also rationalize our findings in the framework of a general electrochemical model. Finally, we show that the doping concentrations in the doped regions at the time of the p-n junction formation are independent of the applied voltage and relatively balanced at approximately 0.11 dopants/MEH-PPV repeat unit in the p-type region and approximately 0.15 dopants/MEH-PPV repeat unit in the n-type region.     

A supramolecularly-caged ionic iridium(III) complex yielding bright and very stable solid-state light-emitting electrochemical cells

A new iridium(III) complex showing intramolecular interligand pi-stacking has been synthesized and used to improve the stability of single-component, solid-state light-emitting electrochemical cell (LEC) devices. The pi-stacking results in the formation of a very stable supramolecularly caged complex. LECs using this complex show extraordinary stabilities (estimated lifetime of 600 h) and luminance values (average luminance of 230 cd m-2) indicating the path toward stable ionic complexes for use in LECs reaching stabilities required for practical applications.     

Dynamic doping and degradation in sandwich-type light-emitting electrochemical cells

Photoluminescence spectroscopy has been performed in situ during device operation and after switch-off on ionic transition metal complex (iTMC)-based sandwich-type light-emitting electrochemical cells (LECs). It is demonstrated that the photoluminescence of the LECs decreases with increasing operating time. For operating times up to three hours the decline in photoluminescence is fully recoverable after switching off the bias. These results imply that doping of the iTMC layer is responsible, not only, for the turn-on of LECs but also for their lifetimes.     

Efficient green-blue-light-emitting cationic iridium complex for light-emitting electrochemical cells

A highly luminescent novel cationic iridium complex [iridium bis(2-phenylpyridine)(4,4'-(dimethylamino)-2,2'-bipyridine)]PF6 was synthesized and characterized using NMR, UV-visible absorption, and emission spectroscopy and electrochemical methods. This complex displays intense photoluminescence maxima in the green-blue region of the visible spectrum and exhibits unprecedented phosphorescence quantum yields, 80 +/- 10% with an excited-state lifetime of 2.2 mus in a dichloromethane solution at 298 K. Single-layer light-emitting electrochemical cells with the charged complex as conducting and electroluminescent material sandwiched between indium-tin oxide and Ag electrodes were fabricated, which emit green-blue light with an onset voltage as low as 2.5 V. Density functional theory calculations were performed to provide insight into the electronic structure of the [iridium bis(2-phenylpyridine)(4,4'-(dimethylamino)-2,2'-bipyridine)]PF6 complex, comparing these results with those obtained for [iridium bis(2-phenylpyridine)(4,4'-tert-butyl-2,2'-bipyridine)]PF6.     

Tailoring noise frequency spectrum to improve NIR determinations

Near infrared spectroscopy (NIR) contains excessive background noise and weak analytical signals caused by near infrared overtones and combinations. That makes it difficult to achieve quantitative determinations of low concentration samples by NIR. A simple chemometric approach has been established to modify the noise frequency spectrum to improve NIR determinations. The proposed method is to multiply one Savitzky-Golay filtered NIR spectrum with another reference spectrum added with thermal noises before the other Savitzky-Golay filter. Since Savitzky-Golay filter is a kind of low-pass filter and cannot eliminate low frequency components of NIR spectrum, using one step or two consecutive Savitzky-Golay filter procedures cannot improve the determination of NIR greatly. Meanwhile, significant improvement is achieved via the Savitzky-Golay filtered NIR spectrum processed with the multiplication alteration before the other Savitzky-Golay filter. The frequency range of the modified noise spectrum shifts toward higher frequency regime via multiplication operation. So the second Savitzky-Golay filter is able to provide better filtering efficiency to obtain satisfied result. The improvement of NIR determination with tailoring noise frequency spectrum technique was demonstrated by both simulated dataset and two measured NIR spectral datasets. It is expected that noise frequency spectrum technique will be adopted mostly in applications where quantitative determination of low concentration sample is crucial.     

Tailoring polycarboxylate architecture to improve the rheological properties of cement paste

Abstract

This study elucidates the link between polycarboxylate (PC) architecture (random vs. block) and rheological properties of cement pastes at a low water-cement ratio (W/C?=?0.22) through a systematic investigation on the rheological properties, adsorption properties, solution viscosity and polymer hydrodynamic radius. Adsorption data show that the adsorption amount of the block PC is larger than that of the random PC while the paste flow is the same even though the dosage of the former is smaller, possibly owing to the fact that the adsorbing carboxylic groups are concentrated at one end in the case of the block PC, and the absence of neutral side chains in the adsorbing block effectively reduces the free energy barrier of PC adsorption. Results on the polymer hydrodynamic radius from dynamic light scattering (DLS) illustrate that the hydrodynamic radius of the block PC is smaller than that of the random PC, and in consistence with the DLS results, the solution of the block PC is also found to have a lower viscosity at the same polymer weight concentration. It is worth-noting that the apparent viscosity of the cement paste has a close relation with the viscosity of PC remaining in solution. The dual effects of a larger adsorption amount and a smaller hydrodynamic radius of the block PC effectively reduce the viscosity of PC remaining in solution, and hence effective reduce the apparent viscosity of cement pastes. It is believed that this study allows for a better understanding of the influences of polycarboxylate architecture on rheological properties of cementitious materials.     

Electrical properties of electrochemically doped organic semiconductors using light-emitting electrochemical cells

We present a study of the electrical properties of electrochemically doped conjugated polymers using polymeric light-emitting electrochemical cells (PLECs) and interpreting the results according to a phenomenological model (PM) which assumes that, above the device turn-on voltage, the bulk transport properties of the doped organic semiconductor are responsible for the main contribution to the whole device conductivity. To confirm the predictions of this model, the dependence of the conductivity of PLECs with different parameters is evaluated and compared with the behavior expected for a doped semiconducting polymeric material. The organic semiconductor doping level, the blend concentration of organic semiconducting molecules, the device thickness, the charge carrier mobility, and the temperature are the parameters varied to perform this analysis. We observed that the device conductivity is independent of the active layer thickness, weakly dependent on the temperature, but strongly dependent on the semiconductor doping level, on the semiconductor fraction in the blend, and on the intrinsic charge carrier mobility. These results were well described by the variable range hopping (VRH) model, which has been widely employed to describe the charge transport in doped semiconducting polymeric materials, confirming the prediction of the phenomenological model. The current analysis demonstrates that PLECs are a suitable system for studying, in situ, the electrochemical doping of semiconducting polymers, permitting the evaluation of material properties as, for instance, the density of electronic charge carriers (and, consequently, the ionic charge carrier concentration) necessary to achieve the maximum electrochemical doping level of the organic semiconductor.     

Near-UV to red-emitting charged bis-cyclometallated iridium(III) complexes for light-emitting electrochemical cells

Herein we report a series of charged iridium complexes emitting from near-UV to red using carbene-based N^C: ancillary ligands. Synthesis, photophysical and electrochemical properties of this series are described in detail together with X-ray crystal structures. Density Functional Theory calculations show that the emission originates from the cyclometallated main ligand, in contrast to commonly designed charged complexes using bidentate N^N ancillary ligands, where the emission originates from the ancillary N^N ligand. The radiative process of this series of compounds is characterized by relatively low photoluminescence quantum yields in solution that is ascribed to non-radiative deactivation of the excited state by thermally accessible metal-centered states. Despite the poor photophysical properties of this series of complexes in solution, electroluminescent emission from the bluish-green to orange region of the visible spectrum is obtained when they are used as active compounds in light-emitting electrochemical cells.     

Solid-state white light-emitting electrochemical cells using iridium-based cationic transition metal complexes

White electroluminescent (EL) emission from single-layered solid-state light-emitting electrochemical cells (LECs) based on host-guest cationic iridium complexes has been successfully demonstrated. The devices show white EL spectra (Commission Internationale de l'Eclairage coordinates ranging from (x, y) = (0.45, 0.40) to (0.35, 0.39) at 2.9-3.3 V with high color rendering indices up to 80. Peak external quantum efficiency and peak power efficiency of the white LEC reach 4% and 7.8 lm/W, respectively. These results suggest that white LECs based on host-guest cationic transition metal complexes may be a promising alternative for solid-state lighting technologies.     

Microcapillary electrochemical droplet cells: applications in solid-state surface analysis

Capillary–based microcells, also known as microcapillary electrochemical droplet cells, have proved their capabilities in various electrochemical surface investigations in recent decades. Due to the large measured current density and the high limiting current, this technique provides high–resolution electrochemical responses. Current densities in the range from a few femto to pico Acm^?2 to hundreds of Acm^?2 can be measured using this technique. Various applications for microcapillary cells have been reported. Technical limitations, such as the Ohmic drop and changes in the composition of the measurement area near the tip of the microcapillary have also been considered by some researchers. The rapid increase in the application of microcells and the increase in the number of related reports published in the literature have paralleled recent attempts to develop and improve microcell setups, showing that this technique is already well established for electrochemical surface studies.     

Polymer light-emitting electrochemical cells: Recent developments to stabilize the p-i-n junction and explore novel device applications

Polymer light-emitting electrochemical cells (PLECs) employ a thin layer of a luminescent conjugated polymer admixed with an ionic source and an ionic conductor for the in-situ formation of p-i-n junction and subsequent efficient injections of both electrons and holes.The junction formation enables the use of air-stable conductors as the cathode and a relatively thick emissive polymer layer that is more compatible with low-cost solution-based processes.This paper overviews the operation mechanism of the PLECs,the properties and drawbacks of the devices.The employment of crosslinkable ionic conductors to stabilize the p-i-n junction is reviewed.The resulting static junction electroluminesces light at high brightness,high efficiency,and prolonged lifetime.Silver paste and carbon nanotubes can be used as the cathode,thus,PLECs were fabricated by lamination.Using single wall carbon nanotubes coated elastic substrate as both anode and cathode,the PLECs can be made highly stretchable.     

Insight into luminescent iridium complexes: Their potential in light-emitting electrochemical cells

Cyclometallated iridium complexes possess fascinating electrochemical and photophysical properties that make them excellent candidates for a variety of photonic and optoelectronic applications. In particular, light-emitting electrochemical cells (LEECs) based on iridium-containing ionic transition-metal complexes (Ir-iTMCs) are a promising alternative to conventional organic light-emitting diodes with several advantages, including a simpler device structure, solution processability, and reduced manufacturing costs. This review aims to provide a comprehensive and systematic overview of the current status of Ir-iTMC-based LEECs using the archetypal complex [Ir(ppy)₂(bpy)]PF₆ as a reference emitter. After a discussion of the device fundamentals and important photophysical and device parameters, key strategies for tuning the emission characteristics and device stability through LUMO and HOMO stabilization/destabilization are presented using numerous examples from the literature, with a particular focus on ligand modification with hydrophobic, electron-withdrawing, and electron-donating substituents, π-stacking interactions, and alternative ancillary and cyclometalated ligand skeletons. Comprehensive data tables summarizing the photophysical and LEEC properties of the various classes of iridium complexes reported to date are also provided. Finally, in an effort to highlight promising directions for future research, the current champion iridium complexes for fabricating state-of-the-art LEECs are identified, and the merits and limitations of existing approaches are discussed.     

Approaching charge balance in organic light-emitting diodes by tuning charge injection barriers with mixed monolayers

Self-assembled monolayers (SAMs) of binary mixtures of 1-butylphosphonic acid and the trifluoromethyl-terminated analogue (4,4,4-trifluoro-1-butylphosphonic acid) were formed on ITO surfaces to tune the work function of ITO over a range of 5.0 to 5.75 eV by varying the mixing ratio of the two adsorbents. The mixed SAM-modified ITO surfaces were used as the anode in the fabrication of OLED devices with a configuration of ITO/SAM/HTL/Alq3/MX/Al, where HTL was the NPB or BPAPF hole-transporting layer and MX was the LiF or Cs(2)CO(3) injection layer. It was shown that, depending on the HTL or MX used, the maximum device current and the maximum luminance efficiency occurred with anodes of different modifications because of a shift in the point of hole/electron carrier balance. This provides information on the charge balance in the device and points to the direction to improve the performance.     

Phenomenological model for the interpretation of impedance/admittance spectroscopy results in polymer light-emitting electrochemical cells

A phenomenological model has been developed to account for the results of impedance/admittance spectroscopy measurements from light-emitting electrochemical cells (LECs) comprising a polymer electrolyte and two different conjugated polymers used as organic semiconductor. The application of a d.c. offset bias superimposed to the a.c. modulation voltage was used to observe the transition from the behavior prior to device operation and after the formation of the electrochemical p-i-n junction. The analysis of the whole device “conductivity” as a function of the applied bias and of the frequency was used to support the assumptions considered to develop the model. The results show that the device, after the p-i-n junction formation, can be considered as composed by two highly conductive electrochemically doped (n and p) regions and a thin (few tens nanometers), insulating layer, where the electrical current is dominated by electronic charge carrier injection via tunneling through a rectangular energy barrier. Before the p-i-n junction formation, there is no doping of semiconductor material, and the device electrical properties are dominated by the intrinsic electronic charge carriers in the organic semiconductor. Results from devices made of organic semiconductors with different band gap energy and different layer thicknesses are used to corroborate the proposed model.     

Efficient and stable solid-state light-emitting electrochemical cell using tris(4,7-diphenyl-1,10-phenanthroline)ruthenium(II) hexafluorophosphate

The complex tris(4,7-diphenyl-1,10-phenanthroline)ruthenium(II), prepared via a simple microwave-assisted synthesis, was used to prepare a single-layer light-emitting electrochemical cell. This device reaches a high power efficiency of 1.9 Lum/W at a brightness of 390 cd/m2. Moreover, its lifetime is an order of magnitude longer than that of a similar cell making use of tris(bipyridine)ruthenium(II) as the emitting complex.