Capacitive biosensor for detection of endotoxin

A capacitive biosensor for the detection of bacterial endotoxin has been developed. Endotoxin-neutralizing protein derived from American horseshoe crab was immobilized to a self-assembled thiol layer on a biosensor transducer (Au). Upon injection of a sample containing endotoxin, a decrease in the observed capacitive signal was registered. Endotoxin could be determined under optimum conditions with a detection limit of 1.0 × 10⁻¹³ M and linearity ranging from 1.0 × 10⁻¹³ to 1.0 × 10⁻¹⁰ M. Good agreement was achieved when applying endotoxin preparations purified from an Escherichia coli cultivation to the capacitive biosensor system, utilizing the conventional method for quantitative endotoxin determination, the Limulus amebocyte lysate test as a reference. The capacitive biosensor method was statistically tested with the Wilcoxon signed rank test, which proved the system is acceptable for the quantitative analysis of bacterial endotoxin (P < 0.05). Figure The flow-injection capacitive biosensor system and the capacitive properties of the transducer surface, where C_SAM is the capacitance change of the self-assembled thiol monolayer, C_P is the capacitance change of the protein layer, C_a is the capacitance change of the analyte layer and C_Total is the total capacitance change measured at the working electrode/solution interface (modified from Limbut et al., 2006. Biosens Bioelectron 22: 233-240)     

Influence of the solvent on the gas chromatographic behaviour of urea herbicides

Summary Degradation products of chlorsulfuron, chlortoluron, diuron, fluometuron, isoproturon, linuron, metabenzthiazuron, metobromuron, and monuron formed in the gas chromatographic injector have been used for identification of the respective herbicides. Mass spectra of the derived compounds were obtained with a quadrupole mass spectrometric detector working in scan mode (20–450 amu). The compounds generated often depended on the solvent used for phenylurea herbicide injection (ethanol, methanol, dichloromethane, and acetonitrile). When methanol and ethanol were used as solvents the major products formed from phenylureas were carbamic acid esters. When acetonitrile or dichloromethane were used the main derivatives were phenylisocyanates. Chlorsulfuron and metabenzthiazuron, however, generated a triazine plus a phenylsulfonamide and a benzothiazolamine, respectively, irrespective of the solvent used. Linuron and diuron behaved similarly and gave degradation products with the same mass spectra. The thermal reactions occurred instantaneously in the injector block and were promoted by the high temperature selected (300°C). Detemination of the compounds derived from urea herbicides, by use of a 30 m BP10 column and a selected ion registering (SIR) program based on two or three ions, can be used for sensitive detection of the presence of urea herbicides in environmental extracts. With standards in methanol instrument detection limits ranged from 0.1 pg for chlorsulfuron (detected as 2-chlorobenzensulfonamide) to 1 pg for monuron and metobromuron (both detected as their carbamic acid methyl esters).RSD were below 9% at the 5 ng L⁻¹ level. The response was linearly dependent on quantily (r>0.9986) in the 5 ng L⁻¹ to 25 μg L⁻¹ range. Unequivocal identification of some phenylurea herbicides was not always possible because some herbicides with similar structures, for example diuron and linuron, gave the same derivative.     

A novel microbial biosensor based on cells of <Emphasis Type="Italic">Gluconobacter oxydans</Emphasis> for the selective determination of 1,3-propanediol in the presence of glycerol and its application to bioprocess monitoring

Novel and selective microbial amperometric biosensors that use Gluconobacter oxydans cells to monitor the bacterial bioconversion of glycerol (Gly) to 1,3-propanediol (1,3-PD) are described. Two different mediators, ferricyanide and flexible polyvinylimidazole osmium functionalized polymer (Os-polymer), were employed to prepare two different microbial biosensors, both of which gave high detection performance. The good operational stabilities of both types of biosensor were underlined by the ability to detect 1,3-PD throughout 140 h of continuous operation. Both microbial biosensor systems showed excellent selectivity for 1,3-PD in the presence of a high excess of glycerol [selectivity ratios (1,3-PD/Gly) of 118 or 245 for the ferricyanide and Os-polymer systems, respectively]. Further, the robustness of each microbial biosensor was highlighted by the high reliability of 1,3-PD detection achieved (average RSD of standards <2%, and well below 4% for samples). The biosensor implementing the Os-polymer mediator exhibited high selectivity towards 1,3-PD detection and allowed moderate sample throughput (up to 12 h⁻¹) when integrated into a flow system. This system was used to monitor the concentration of 1,3-PD during a real bioprocess. Results from biosensor assays of 1,3-PD in bioprocess samples taken throughout the fermentation were in a very good agreement with results obtained from reference HPLC assays (R ² = 0.999).     

Immobilization of Hemoglobin on the Gold Colloid Modified Pretreated Glassy Carbon Electrode for Preparing a Novel Hydrogen Peroxide Biosensor

A novel hydrogen peroxide (H₂O₂) biosensor was developed by immobilizing hemoglobin on the gold colloid modified electrochemical pretreated glassy carbon electrode (PGCE) via the bridging of an ethylenediamine monolayer. This biosensor was characterized by UV-vis reflection spectroscopy (UV-vis), electrochemical impendence spectroscopy (EIS) and cyclic voltammetry (CV). The immobilized Hb exhibited excellent electrocatalytic activity for hydrogen peroxide. The Michaelis–Menten constant (K _m) was 3.6 mM. The currents were proportional to the H₂O₂ concentration from 2.6 × 10⁻⁷ to 7.0 × 10⁻³ M, and the detection limit was as low as 1.0 × 10⁻⁷ M (S/N = 3).     

Electrochemiluminescent aptamer biosensor for the determination of ochratoxin A at a gold-nanoparticles-modified gold electrode using N-(aminobutyl)-N-ethylisoluminol as a luminescent label

A highly selective electrochemiluminescent biosensor for the detection of target nephrotoxic toxin, ochratoxin A (OTA), was developed using a DNA aptamer as the recognition element and N-(4-aminobutyl)-N-ethylisoluminol (ABEI) as the signal-producing compound. The electrochemiluminescent aptamer biosensor was fabricated by immobilizing aptamer complementary DNA 1 sequence onto the surface of a gold-nanoparticle (AuNP)-modified gold electrode. ABEI-labeled aptamer DNA 2 sequence hybridized to DNA 1 and was utilized as an electrochemiluminescent probe. A decreased electrochemiluminescence (ECL) signal was generated upon aptamer recognition of the target OTA, which induced the dissociation of DNA 2 (ABEI-labeled aptamer electrochemiluminescent probe) from DNA 1 and moved it far away from the electrode surface. Under the optimal conditions, the decreased ECL intensity was proportional to an OTA concentration ranging from 0.02 to 3.0 ng mL^-1, with a detection limit of 0.007 ng mL^-1. The relative standard deviation was 3.8% at 0.2 ng mL^-1 (n = 7). The proposed method has been applied to measure OTA in naturally contaminated wheat samples and validated by an official method. This work demonstrates the combination of a highly binding aptamer with a highly sensitive ECL technique to design an electrochemiluminescent biosensor, which is a very promising approach for the determination of small-molecule toxins.     

Preparation of antibodies and development of a sensitive immunoassay with fluorescence detection for triazine herbicides

Specific polyclonal antibodies against s-triazine herbicides were obtained by preparing immunogens coupling home-synthesized haptens derivatives of simazine (6-chloro-N-ethyl-N′-ethyl-1,3,5-triazine-2,4-diamine) to lysine groups of hemocyanin from keyhole limpets and bovine serum albumin carrier proteins. Three highly sensitive rabbit antisera were obtained and evaluated with a battery of six enzyme tracers derived from triazine structures in an optimized ELISA format. The antiserum As8 and the HRP-2f tracer, which yield the best assay sensitivity for simazine (detection limit 0.11 ± 0.02 μg L⁻¹, IC₅₀ 0.88 ± 0.04 μg L⁻¹), were applied to the development of a sensitive flow-through immunoassay for the analysis of this herbicide. The automated assay was based on a direct competitive immunosorbent assay and fluorescence detection. The optimized method presents an IC₅₀ value of 0.35 ± 0.04 μg L⁻¹ with a detection limit of 1.3 ± 0.9 ng L⁻¹ and a dynamic range from 0.010 to 7.5 μg L⁻¹ simazine. The generic nature of the antiserum was shown by good relative cross-reactivities with other triazines such as atrazine (420%) or propazine (130%) and a lower response to terbutylazine (6.4%) and desethyl-atrazine (2.2%). No cross-reactivity was obtained for nonrelated pesticides such as 2,4-dichlorophenoxyacetic acid or linuron and the assay could be applied as a screening method for triazine herbicides. The total analysis time was 30 min per determination and the immunosensor could be reused for more than 150 cycles without significant loss of activity. The immunosensor has been successfully applied to the direct analysis of simazine in surface water samples at the nanogram per liter level. The results obtained by comparative analysis of the immunosensor with a chromatographic procedure for triazines showed a close correspondence.     

Development of a photosystem II-based optical microfluidic sensor for herbicide detection

Herbicides are highly toxic for both human and animal health. The increased application of herbicides in agriculture during the last decades has resulted in the contamination of both soil and water. Herbicides, under illumination, can inhibit photosystem II electron transfer. Photosynthetic membranes isolated from higher plants and photosynthetic micro-organisms, immobilized and stabilized, can serve as a biorecognition element for a biosensor. The inhibition of photosystem II causes a reduced photoinduced production of hydrogen peroxide, which can be measured by a chemiluminescence reaction with luminol and the enzyme horseradish peroxidase. In the present work, a compact and portable sensing device that combines the production and detection of hydrogen peroxide in a single flow assay is proposed for herbicide detection.     

Acetylcholinesterase-based biosensors for quantification of carbofuran, carbaryl, methylparaoxon, and dichlorvos in 5% acetonitrile

Amperometric acetylcholinesterase biosensors have been developed for quantification of the pesticides carbofuran, carbaryl, methylparaoxon, and dichlorvos in phosphate buffer containing 5% acetonitrile. Three different biosensors were built using three different acetylcholinesterase (AChE) enzymes—AChE from electric eel, and genetically engineered (B394) and wild-type (B1) AChE from Drosophila melanogaster. Enzymes were immobilized on cobalt(II) phthalocyanine-modified electrodes by entrapment in a photocrosslinkable polymer (PVA-AWP). Each biosensor was tested against the four pesticides. Good operational stability, immobilisation reproducibility, and storage stability were obtained for each biosensor. The best detection limits were obtained with the B394 enzyme for dichlorvos and methylparaoxon (9.6 × 10⁻¹¹ and 2.7 × 10⁻⁹ mol L⁻¹, respectively), the B1 enzyme for carbofuran (4.5 × 10⁻⁹ mol L⁻¹), and both the B1 enzyme and the AChE from electric eel for carbaryl (1.6 × 10⁻⁷ mol L⁻¹). Finally, the biosensors were used for the direct detection of the pesticides in spiked apple samples.     

Development of electrochemical DNA biosensor for Trichoderma harzianum based on ionic liquid/ZnO nanoparticles/chitosan/gold electrode

Electrochemical DNA biosensor was successfully developed by depositing the ionic liquid (e.g., 1-ethyl-3-methylimidazolium trifluoromethanesulfonate ([EMIM][Otf])), ZnO nanoparticles, and chitosan (CHIT) nanocomposite membrane on a modified gold electrode (AuE). The electrochemical properties of the [EMIM][Otf]/ZnO/CHIT/AuE for detection of DNA hybridization were studied. Under optimal conditions using cyclic voltammetry, the target DNA sequences could be detected in the concentration range of 1.0 × 10⁻¹⁸ to 1.82 × 10⁻⁴ mol L⁻¹, and with the detection limit of 1.0 × 10⁻¹⁹ mol L⁻¹. This DNA biosensor detection approaches provide a quick, sensitive, and convenient method to be used in the identification of Trichoderma harzianum.     

A compact miniaturized continuous flow system for the determination of urea content in milk

A multicommutation-based flow system with photometric detection was developed, employing an analytical microsystem constructed with low temperature co-fired ceramics (LTCC) technology, a solid-phase reactor containing particles of Canavalia ensiformis DC (urease source) immobilized with glutaraldehyde, and a mini-photometer coupled directly to the microsystem which monolithically integrates a continuous flow cell. The determination of urea in milk was based on the hydrolysis of urea in the solid-phase reactor and the ammonium ions produced were monitored using the Berthelot reaction. The analytical curve was linear in the urea concentration range from 1.0 × 10⁻⁴ to 5.0 × 10⁻³ mol L⁻¹ with a limit of detection of 8.0 × 10⁻⁶ mol L⁻¹. The relative standard deviation (RSD) for a 2.0 × 10⁻³ mol L⁻¹ urea solution was lower than 0.4% (n = 10) and the sample throughput was 13 h⁻¹. To check the reproducibility of the flow system, calibration curves were obtained with freshly prepared solutions on different days and the RSD obtained was 4.7% (n = 6). Accuracy was assessed by comparing the results of the proposed method with those from the official procedure and the data are in close agreement, at a 95% confidence level.     

Enzyme biosensor based on the immobilization of HRP on SiO<Subscript>2</Subscript>/BSA/Au composite nanoparticles

In this work, an enzyme biosensor based on the immobilization of horseradish peroxidase (HRP) on SiO₂/BSA/Au/thionine/nafion-modified gold electrode was fabricated successfully. Firstly, nafion was dropped on the surface of the gold electrode to form a nafion film followed by chemisorption of thionine (Thi) as an electron mediator via the ion-exchange interaction between the Thi and nafion. Subsequently, the SiO₂/BSA/Au composite nanoparticles were assembled onto Thi film through the covalent bounding with the amino groups of Thi. Finally, HRP was immobilized on the SiO₂/BSA/Au composite nanoparticles due to the covalent conjugation to construct an enzyme biosensor. The surface topographies of the SiO₂/BSA/Au composite nanoparticles were investigated by using scanning electronic microscopy. The stepwise self-assemble procedure of the biosensor was further characterized by means of cyclic voltammetry and chronoamperometry. The enzyme biosensor showed high sensitivity, good stability and selectivity, a wide linear response to hydrogen peroxide (H₂O₂) in the range of 8.0 × 10^-6 ∼ 3.72 × 10^-3 mol/L, with a detection limit of 2.0 × 10^-6 mol/L. The Michaelies-Menten constant K_M^app K_M^{app} value was estimated to be 2.3 mM.     

Production and analytical characterization of neopterin immunoreagents for biosensor developments

Neopterin is a valuable biomarker of cellular immunity associated with various pathological situations such as viral and bacterial infections, autoimmune, cardiovascular, neurodegenerative and malignant disorders. To produce specific antibodies against neopterin for a rapid multi-biomarker-based diagnosis, a novel hapten derivative was synthesized and attached to carrier proteins. The thoroughly characterized conjugates were used for immunization of BALB/c mice and rabbits. The produced monoclonal antibody reached in both direct and indirect enzyme-linked immunosorbent assay (ELISA) format LoD of 0.18 and 0.45 μg L⁻¹, respectively, and was a superior immunoreagent for further biosensor developments with regard to assay sensitivity and material availability. The best polyclonal antibody was somewhat more sensitive in direct ELISA with LoD of 0.05 μg L⁻¹. The optimized ELISA method was evaluated with blood samples collected from patients with renal insufficiency, patients with sepsis, patients without confirmed clinical diagnosis, and healthy volunteers. In plasma samples, neopterin concentrations ranging from 3.2 to 103 μg L⁻¹ could be determined with the monoclonal ELISA whereas twofold lower results were obtained with the polyclonal ELISA. A satisfactory correlation of results was found between the polyclonal ELISA and IBL Neopterin ELISA kit within the concentration range 0.5–16 μg L⁻¹ (R = 0.874; n = 40), and slightly lower correlation was found for monoclonal-based ELISA (R = 0.819; n = 40). These data show that the generated antibodies may be used as functional analytical reagents for the integration into multianalyte biochip detection systems.     

NADH screen-printed electrodes modified with zirconium phosphate,Meldola blue,and Reinecke salt. Application to the detection of glycerol by FIA

Bulk screen-printed electrodes (bSPEs) modified with zirconium phosphate (ZrP) and Meldola blue (MB) and by electrochemical deposition of a Reineckate film (bMBZrPRs-SPEs) have been constructed and used as NADH sensors. Cyclic voltammetric investigation of these bulk electrochemically modified screen-printed electrodes revealed stable catalytic activity in oxidation of the reduced form of the coenzyme nicotinamide adenine dinucleotide (NADH). Flow-injection analysis (FIA) coupled with amperometric detection confirmed the improved stability of the bMBZrPRs-SPEs (10⁻⁴ mol L⁻¹ NADH, %RSD = 4.2, n = 90, pH 7.0). Other conditions, for example applied working potential (+50 mV relative to Ag|AgCl), flow rate (0.30 mL min⁻¹) and pH-dependence (range 4.0–10.0) were evaluated and optimized. A glycerol biosensor, prepared by immobilizing glycerol dehydrogenase (GDH) on the working electrode area of a bMBZrPRs-SPE, was also assembled. The biosensor was most stable at pH 8.5 (%RSD = 5.6, n = 70, 0.25 mmol L⁻¹ glycerol). The detection and quantification limits were 2.8 × 10⁻⁶ and 9.4 × 10⁻⁶ mol L⁻¹, respectively, and the linear working range was between 1.0 × 10⁻⁵ and 1.0 × 10⁻⁴ mol L⁻¹. To assess the effect of interferences, and recovery by the probe we analyzed samples taken during fermentation of chemically defined grape juice medium and compared the results with those obtained by HPLC.     

Rapid residue analysis of four triazolopyrimidine herbicides in soil, water, and wheat by ultra-performance liquid chromatography coupled to tandem mass spectrometry

A sensitive and effective method for simultaneous determination of triazolopyrimidine sulfonamide herbicide residues in soil, water, and wheat was developed using ultra-performance liquid chromatography coupled with tandem mass spectrometry. The four herbicides (pyroxsulam, flumetsulam, metosulam, and diclosulam) were cleaned up with an off-line C18 SPE cartridge and detected by tandem mass spectrometry using an electrospray ionization source in positive mode (ESI+). The determination of the target compounds was achieved in <2.0 min. The limits of detection were below 1 μg kg⁻¹, while the limits of quantification did not exceed 3 μg kg⁻¹ in different matrices. Quantitation was determined from calibration curves of standards containing 0.05–100 μg L⁻¹ with r ² > 0.997. Recovery studies were conducted at three spiked levels (0.2, 1, and 5 μg kg⁻¹ for water; 5, 10, and 100 μg kg⁻¹ for soil and wheat). The overall average recoveries for this method in water, soil, wheat plants, and seeds at three levels ranged from 75.4% to 106.0%, with relative standard deviations in the range of 2.1–12.5% (n = 5) for all analytes.     

Kinetic-potentiometric assay of formaldehyde in pharmaceutical and industrial samples, monitored by copper solid ion selective electrode, after its reaction with the copper(II)-bis-(ethylenediamine) complex

A kinetic-potentiometric method is described for the quantitative assay of formaldehyde (HCHO) in pharmaceutical and industrial preparations. It is based on the reaction of HCHO with (ethylenediamine)-Cu(II)-sulfate [Cu(CH₂NH₂)₂(H₂O)₂] · SO₄. The changes in potential, resulting from the release of the Cu(II) cations, are monitored with a Cu(II)-ion selective electrode. The calibration curve for the HCHO is linear in the concentration range 50–250 mg L⁻¹, with a limit of detection of 8.5 mg L⁻¹. The method shows very good reproducibility with an RSD of 2.6% for successive injections (n = 5) of 150 mg L⁻¹ HCHO primary solution, while it is interference free. The method was successfully tested in various industrial and pharmaceutical preparations.     

Polymer supported 5,10,15,20-tetrakis(phenoxy acetic acid)porphyrin derivative for separation and preconcentration of d- and f-electron metals

5,10,15,20-tetrakis(phenoxy acetic acid) porphyrin (PAAP) was covalently linked to Merrifield chloromethylated resin. Characterization of PAAP and the modified polymeric matrix were performed by ¹H NMR, FTIR and elemental analysis. The sorbent was used for the separation and enrichment of the d-electron metals (Mn(II), Co(II), Ni(II), Cu(II) and Zn(II)) at pH 6–8 and of the f-electron metals U(VI) and Th(IV) at pH 4–5. The metals ions were preconcentrated with a concentration factor range of 115–215 and then determined by flame atomic absorption spectrometry or visible spectrophotometry using Arsenazo(III). The retained metals were eluted with 2.0 mol L⁻¹ HNO₃ in the case of the d-electron metals and 0.1/0.25 mol L⁻¹ HCl in the case of the f-electron metals. The procedure was validated by analyzing the NIST standard reference material 2709 (San Joaquin Soil). Correspondence: Melek Merdivan, Chemistry Department, Faculty of Arts and Sciences, Dokuz Eylul University, 35160 Buca, Izmir, Turkey     

Determination of cocaine on banknotes through an aptamer-based electrochemiluminescence biosensor

A novel electrochemiluminescence (ECL) “sandwich” biosensor has been developed to detect cocaine. The sandwich biosensor was fabricated on the basis of the fact that a single aptamer could be split into two fragments and the two dissociated parts could form a folded, associated complex in the presence of targets. One of these (capture probe), which had hexane–thiol at its 5′-terminus, was immobilized on a gold electrode via thiol–gold binding. The other one (detection probe) was labeled with the ECL reagent tris(2,2′-bipyridyl)ruthenium(II)-doped silica nanoparticles (RuSiNPs) at its 3′-terminus. Owing to the weak interaction between the two fragments, the sensor exhibited a low ECL signal in the absence of cocaine. After the target cocaine had been added to the solution, it induced association of the two fragments and stabilized the associated complexes, leading to immobilization of RuSiNPs on the electrode surface, and the ECL detected on the electrode surface was enhanced. The enhanced ECL intensity was directly proportional to the logarithm of the cocaine concentration in the range from 1.0 × 10⁻⁹ to1.0 × 10⁻¹¹ mol/L, with a detection limit of 3.7 × 10⁻¹² mol/L. The biosensor was applied to detect trace amounts of cocaine on banknotes with satisfactory results.     

Direct electrochemistry and electrocatalysis of hemoglobin in a multilayer {nanogold/PDDA}n inorganic–organic hybrid film

A new amperometric biosensor for hydrogen peroxide (H₂O₂) has been developed that is based on direct electrochemistry and electrocatalysis of hemoglobin (Hb) in a multilayer inorganic–organic hybrid film. o-Phenylenediamine (PDA) was electropolymerized onto a glassy carbon electrode (GCE), and then negatively charged nanogold particles and positively charged poly(diallyldimethylammonium chloride) (PDDA) were alternately assembled on the PDA/GCE surface. Finally, Hb was electrostatically adsorbed on the surface of gold nanoparticles. The electrochemical behavior of the resulting biosensor (Hb/{nanogold/PDDA}_n/PDA/GCE) was assessed and optimized. The performance and factors influencing the biosensor were studied in detail. Under optimal conditions, the immobilized Hb displayed good electrocatalytic response to the H₂O₂ reduction ranging from 1.3 μM to 1.4 mM with a detection limit of 0.8 μM (at 3δ). In addition, the biosensor exhibited rapid response, good reproducibility, and long-term stability. Electronic supplementary material to this paper is available in electronic form at Correspondence: Dianyong Tang, Department of Chemistry and Life Science, Leshan Teachers College, Sichuan (Leshan) 614000, P.R. China     

Herbicides in Photosynthesis Research

Photosynthesis and herbicide research have a long common history. Soon after the introduction of a new group of highly effective herbicides in 1956, the substituted aryl ureas, their mode of action was recognized to be the inhibition of light-driven electron flow and photosynthetic oxygen evolution. Many subsequent highly successful commercial herbicides, including those from other chemical classes, act by this mechanism. The study of their interaction with the photosynthetic system at the molecular level is a prime example of how rapidly advances in unraveling the mechanism of photosynthesis can be translated into practical uses. At the same time the herbicides continued to be valuable and efficient tools in photosynthesis research. In the past herbicides were instrumental in establishing many principal features of the biochemistry and biophysics of photosynthesis, in particular the role of plastoquinone, which is displaced from its binding pocket in one of the protein subunits of the photosystem II. Their further use in elucidating the molecular biology of photosynthesis is illustrated by the recent importance of herbicide-tolerant mutants for determining structural aspects of photosystem II. We will review the past and present state of the interaction of herbicide and photosynthesis research and will provide a model for the orientation of herbicides within the three dimensional structure of their target, the D1 protein of photosystem II.     

Gas phase and water solution conformational analysis of the herbicide diuron (DCMU): an ab initio study

In the present work, the conformational equilibrium for the herbicide diuron (DCMU) has been investigated using high level ab initio calculations. The solvent effect was included through two different continuum models: (1) the real cavity IPCM method and (2) the standard dipole Onsager model SCRF. The effect due to solute-solvent hydrogen-bond interactions was analyzed considering a hybrid discreet-continuum model. At the Hartree-Fock level, the gas phase results showed that only the trans forms (A and B) are present in the equilibrium mixture, with the relative concentrations found to be 33% (A) and 67% (B) (HF/6-311+G**//6-31G**). When the electronic correlation effect is included (MP2/6-31G*//HF/6-31G*), a relative stabilization of the cis forms was observed, with the conformational distribution calculated as 38% (A), 50% (B), 6% (C) and 6% (D). The trans conformations were found to be completely planar, which has been considered to be a prerequisite for the herbicide binding. In water solution, the trans conformation A should be the most abundant conformer, the IPCM and SCRF values being ca. 100% and ca. 85% respectively. The IPCM calculations with the isodensity level set to 0.0005 present a conformational distribution close to that obtained from the hybrid model [92% (A) and 8% (B)], which has been considered our best solvent approach. Regarding the biological action of urea-type herbicides, the results presented here are important, because some QSAR studies have suggested that the partition coefficient is related to the herbicide activity, so the conformational equilibrium may play a role in the biological action. Received: 23 February 1998 / Accepted: 28 May 1998 / Published online: 19 August 1998