Comparison of recoveries of inogranic and organic incorporated75Se by four mineralization methods of biological material

The recovery of selenium⁷⁵Se added as selenite to human blood and to mixed food, and the recovery of biologically incorporated⁷⁵Se from different rat tissues were determined by using four mineralization methods. The recoveries of⁷⁵Se after dry ashing /HNO₃, Mg/NO₃/₂/ and after three wet digestion methods — 1. HNO₃, HClO₄ 2. HNO₃, HClO₄, H₂SO₄ 3. HNO₃, HClO₄, MgCl₂ were as follows: 50–106%, 96–99%, 92–99% and 97–100%, resp. Losses of⁷⁵Se in wet digestion /HNO₃, HClO₄/ were observed at the end of the procedure, when an excess of acids was evaporated. The addition of MgCl₂ to the digestion mixture prevented the escape of⁷⁵Se and thus permitted the total evaporation of the digest without any loss of selenium.     

Studies on Synthesis and Effect of Dopants on Conductivity and Morphology of Organically Soluble Poly(o-anisidine)

Synthesis of poly(o-anisidine) doped with various protonic acids by using ammonium persulphate as oxidizing agent were carried out in aqueous acid media. Influences of protonic acids on the physicochemical properties were investigated. The various process parameters were optimized to obtain poly(o-anisidine) in the conducting salt phase form. The results are discussed with references to different protonic acids. It was observed that poly(o-anisidine) is highly soluble in organic solvents, such as m-cresol and N-methyl pyrrolidinone (NMP). The polymers were characterized by UV-Visible, FTIR, SEM, XRD and conductivity measurements. A result shows that, different types of dopant acids HCl, H₂SO₄ and HClO₄ affect the morphology and electrical conductivity of the polymer. The electrical conductivity of the polymer follows the order HCl >H₂SO₄>HClO₄. Thus the effect of dopant ion type and the size of its negative ions influence the physico-chemical properties. UV-Vis absorption spectra shows peaks at 740–783 nm with shoulder at 380–420 nm as characteristic peaks for the emeraldine salt (ES) phase of poly(o-anisidine) POA. The FTIR spectra show a broad and intense band at ～2800–3001 cm^?1 and ～1159–1170 cm^?1 that account for the formation of ES phase of the polymer. The X-ray diffraction spectra show a characteristic peak at 20–30^o, 2θ range which reveals partial crystalline structure. The conductivity of the poly(o-anisidne) salt was found to be in the range of 10^?3 to 10^?2 S/cm. SEM studies of poly(o-anisidine) doped with HCl shows the continuous granular uniform morphology with sub-micrometer evenly distributed particles of size ～100–200 nm.     

In situ Near-Infrared Spectroelectrochemical Investigation of Redox States of Polyaniline during Growth and Doping

In situ near-infrared (NIR) spectroelectrochemical studies during growth and dedoping/redoping of polyaniline (PANI) in the range between 1200 to 3000 nm are carried out in 1 M aqueous solutions of HCl, H₂SO₄, and HClO₄ acids andp-toluene sulfonic acid (PTSA). The results show three characteristic absorption bands around 1440, 1900, and 2500 nm. The band at 2500 nm is characteristic of mobile charge carriers. The PANI prepared in HClO₄ keeps memory of the size of the doping anion (ClO₄ ^–) and can be redoped only with the same or smaller anions (Cl^– and SO₄ ^2– or HSO₄ ^–) while it cannot be redoped to any significant extent by a larger anion (PTSA^–).     

A kinetic study of the oxidation of 3- and 4-pyridinemethanol,and 3- and 4-pyridinecarboxaldehyde by chromium(VI) in acidic aqueous media

Oxidation of 3-pyridinemethanol (3-pyol), 4-pyridinemethanol (4-pyol), 3-pyridinecarboxaldehyde (3-pyal) and 4-pyridinecarboxaldehyde (4-pyal) by Cr^VI was studied under pseudo-first-order conditions in the presence of a large excess of reductant and at various H_aq ⁺ concentrations; [Cr^VI] = 8 × 10^–4 M, [reductant] = 0.025–0.20 M, [HClO₄] = 1.0 and 2.0 M (I = 1.2 and 2.1 M) or 0.5–2.0 (I = 2.1 M). A linear dependence of the pseudo-first-order rate constant (k _obs) on [reductant] and a parabolic function of k _obs versus [H⁺] lead to the rate law: –d[Cr^VI]/dt = (a + b[H⁺]²)[reductant][Cr^VI], where a and b describe the reaction paths via HCrO₄ ^– and H₃CrO₄ ⁺ species respectively, and are composite values including rate constants and equilibrium constants. The apparent activation parameters were determined from second-order rate constants at 1.0 and 2.0 M HClO₄, at three temperatures within the 293–323 K range. The presence of chromium species with intermediate oxidation states – Cr^V, Cr^IV and Cr^II, was deduced based on e.s.r. measurements and the kinetic effects of Mn^II or O₂ (Ar), respectively. The alcohols were oxidized to the aldehydes, and carboxylic acids and the aldehydes to the carboxylic acids. Chromium(III) was in the form of the [Cr(H₂O)₆]³⁺ complex.     

Synthesis and spectroscopy of tpps-doped silica gels by the sol-gel process

Tetraphenylporphinetetrasulfonic acid (TPPS), which is well known as a photochemical hole-burning (PHB) dye, was incorporated in silica gels obtained by the sol-gel process from tetramethoxysilane (TMOS). The form of TPPS must be free base (H₂P), which exists in basic condition, to be active in PHB. To obtain transparent and higher density silica gels doped with free-base TPPS, two-step hydrolysis processes using solutions containing NaOH were developed, and the gels having bulk density of about 1.5 g/cm³ were synthesized. The form of TPPS in the gels was investigated by measuring the absorption and luminescence spectra, and it was found that in the silica gels almost all the TPPS retained free-base form at the molar ratio of NaOH/TMOS above 10^–3.     

Kinetic study of the aquation of K2 TcBr6 in perchlorate solutions

The aquation of TcBr ₆ ^2– in perchlorate solutions at various hydrogen ion concentrations and ionic strengths has been investigated. Although the same products form in all cases the proportions of the cationic and neutral products depend on the [H⁺] and the ionic strength. Differences in LiClO₄/HClO₄ and NaClO₄/HClO₄ can be attributed to differences in the activities, although at constant ionic strength. A rate constant of 1.75·10^–5 s^–1 was found for the aquation at =1, together with an activation energy of 101.6±12.5 kJ/mol.     

New effective and selective extractants for separation and determination of silver

Summary Isopropyl-N-alkylthiocarbamates have been studied as extractants for preconcentration of silver trace amounts and for separation of silver macroquantities. It has been shown that the 0.05M reagents in chloroform extract trace amounts of silver with high distribution coefficients from HNO₃, H₂SO₄, HClO₄ and HCl solutions in wide range of their concentrations. The highest selectivity is obtained when HNO₃, H₂SO₄ or HClO₄ solutions are used. Besides silver only mercury and palladium are extracted. When HC1 solutions are used, gold is also transferred into organic phase. Isopropyl-N-alkylthiocarbamates are effective for extraction of silver from its concentrated (up to 1M) solutions, particularly from HNO₃ solutions: more than 99.9% of silver is extracted even at 2-fold reagent excess. Some characteristics of reagents themselfes have been investigated, such as dissociation, protonation, distribution between organic and aqueous phases and association in organic solvents. The thion forms are found to be predominant. Silver is extracted as coordination solvated compounds Ag(HL) _n X, where X=Cl, Br, J, NO₃. Sulfur serves as a donor atom for their formation.The procedures for silver determination in geological samples by flame atomic absorption (3×10^–7%) and atomic emission (1×10^–7%) have been developed. The procedures for atomic emission determination of 23 trace elements (5×10^–8–1×10^–5%) and for electrothermal atomic absorption determination of 17 trace elements (4×10^–9–8×10^–6%) in high purity silver have also been developed.

---

Neue wirksame und selektive Extraktionsmittel für die Trennung und Bestimmung von Silber

Zusammenfassung Isopropyl-N-alkylthiocarbamate wurden als Extraktionsmittel für die Anreicherung von Silberspuren und für die Abtrennung von Makromengen Silber geprüft. Es ergab sich, daß solche 0,05M, in Chloroform gelöste Reagenzien Silberspuren mit hohen Verteilungskoeffizienten aus HNO₃, H₂SO₄, HClO₄ und HCl extrahieren. Die beste Selektivität wurde mit HNO₃, H₂SO₄ oder HClO₄erzielt. Neben Silber werden nur Quecksilber und Palladium extrahiert. Verwendet man HCl, so geht auch Gold in die organische Phase. Isopropyl-N-alkylthiocarbamate eignen sich für die Extraktion von Silber aus konzentrierten (bis zu 1M) Lösungen, besonders aus HNO₃: mehr als 99,9% Silber werden mit zweifachem Reagensüberschuß extrahiert. Einige charakteristische Eigenschaften der in Rede stehenden Reagenzien wurden untersucht: z. B. die Dissoziation, die Protonation, die Verteilung zwischen organischer und wäßriger Phase und die Assoziation in organischen Lösungsmitteln. Hauptsächlich liegen diese Reagenzien in Thionform vor. Silber wird als Ag(HL) _n X extrahiert, worin X für Cl, Br, J oder NO₃ steht. Schwefel fungiert als Donatoratom für deren Bildung.Verfahren zur Silberbestimmung in geologischen Proben mit Hilfe der Flammen-Atomabsorption (3×10^–7%) bzw. der atomaren Emission (l×10^–7) wurden ausgearbeitet. Außerdem wurden auch Verfahren zur Bestimmung von 23 Spurenelementen mittels atomarer Emission (5×10^–8 bis 1×10^–5%) und von 17 Spurenelementen mittels elektrothermaler Atomabsorption (4×10^–9 bis 8×10^–6%) in hochgereinigtem Silber entwickelt.

---

---

The paper has been presented at the Fifth European Conference on Analytical Chemistry (Euroanalysis V), Cracow, August 26–31, 1984.     

Preparation and Characterization of Highly Proton-Conductive Composites Composed of Phosphoric Acid-Doped Silica Gel and Styrene-Ethylene-Butylene-Styrene Elastomer

Highly proton-conductive elastic composites have been successfully prepared from H₃PO₄-doped silica gel and a styrene-ethylene-butylene-styrene (SEBS) block elastic copolymer. Ionic conductivities of the composites depended on the concentration of H₃PO₄ and the heat treatment temperature of the H₃PO₄-doped silica gel. It was found that H₃PO₄ added is present mainly as free orthophosphoric acid in the silica gel. The composite composed of H₃PO₄-doped silica gel with a molar ratio of H₃PO₄/SiO₂ = 0.5 heat-treated at temperatures below 200°C and SEBS elastomer in 5 mass% showed a high conductivity of 10^–5 S cm^–1 at 25°C in an dry N₂ atmosphere. The water adsorption during a storage in 25% relative humidity at room temperature for 1 day enhanced the ionic conductivities of composites by about one order of magnitude. Lower conductivities obtained in the composite with the H₃PO₄-doped silica gel heat-treated at 250°C for 1 h were due to the formation of crystalline Si₃(PO₄)₄. The temperature dependence of conductivity of the composites was the Vogel-Tamman-Fulcher type, indicating that proton was transferred through a liquidlike phase formed in micropores of the H₃PO₄-doped silica gels. The temperature dependence of the modulus of the composite was similar to that of the SEBS elastomer. The thermoplastically deforming temperature of the composite was around 100°C, which was higher by 30°C than that of the SEBS elastomer.     

Die kinetische polarographische Stufe des Urans in Gegenwart von Chlorat-Ionen

An increase of the 2nd polarographic uranium(VI) wave has been observed in the presence of chlorate ions in HClO₄–NaClO₄, or HClO₄–NaClO₄–NaCl supporting electrolyte, resp. The polarographic measurements at different temperatures and at various perchloric acid concentrations show that this increase is due to a kinetic U(III)-U(IV) current. The activation parameters of the U(III)-U(IV) oxidation reaction with ClO₃ ^– have been calculated usingKautecky's method.The approximately 5fold increase of the 2nd polarographic wave allows the determination of small amounts of uranium (10^–5–10^–6 mole/l).

---

---

Mit 2 Abbildungen     

Liquid-liquid extraction of molybdenum(VI) and uranium(VI) by LIX 622

The order of extraction of Mo(VI) from 1M acid solutions by 5% (v/v) LIX 622 (HL) in benzene is HCl>HNO₃>HClO₄>H₂SO₄, and extraction decreases with increasing concentration of HCl and H₂SO₄, and increases slightly with increasing concentration of HNO₃ and HClO₄. The extracted species is shown to be MoO₂L₂ as established by IR data of organic extracts and the extracted species in the solid form. Extraction is almost quantitative at and above 10% LIX 622, and is found to be independent of [Mo(VI)] in the range of 10^–4 to 10^–3 M. The diluents CCl₄, CHCl₃ and C₆H₆ are found to be superior to solvents of high dielectric constant for extraction of Mo(VI). Extraction of uranium(VI) by 10% (v/v) LIX 622 in benzene was found to increase with increasing equilibrium pH (3.0 to 6.0), and becomes quantitative at pH 5.9. Tributyl phosphate acts as a modifier up to 2% (v/v). Thorium(IV) is almost not extracted by LIX 622 or its mixture. Separation of Mo(VI) and U(VI) is feasible.     

Semi-empirical calculations on the structure of the oxonium ion in various crystal sites and relative acidity scale

The structure of the H₃O⁺ ion embedded in a solid environment (H₃O⁺X^–, X^– = Cl^–, NO ₃ ^– , ClO ₄ ^– ) is studied using a modified version of CNDO/2. In this calculation the effect of the first shells of nearest neighbours is taken into account and the effects of second nearest neighbours are introduced by a simulation procedure. Electronic effects are also included. The ion structure is more planar in nitrate than in perchlorate environment and the hydrogen bonds are slightly bent. Trends in structural parameters are compared with chemical properties of the hydrogen bonds and parallels the Hammett acidity scale HNO₃ < HCl < HClO₄.     

Determination of oxytetracycline in urine and human serum by differential pulse polarography

Summary A differential pulse polarographic method for the determination of oxytetracycline in urine and human serum in acid media (HClO₄ of pH 2) is proposed. The effects of the amount of sample taken and the concentration of HClO₄ present were investigated. The detection limit was 5.5×10^–6 mol/l. The standard deviation of the determination of 5.5×10^–5 mol/l of oxytetracycline in 2 ml of urine was 1.7×10^–6 mol/l and that of the determination of 5.5×10^–5 mol/l of oxytetracycline in 2 ml of human serum was 1.9×10^–6 mol/l.

---

Bestimmung von Oxytetracyclin in Urin und Humanserum durch Differential-Pulspolarography

     

Influence of molar ratios of precursor,catalyst, solvent and water on monolithicity and physical properties of TMOS silica aerogels

In continuation to our earlier work on aerogels, the experimental results on the monolithicity and physical properties of silica aerogels as a function of the molar ratios of tetramethoxysilane (TMOS) precursor, catalyst (NH₄OH), methanol (MeOH) solvent and water, are reported. The molar ratios of NH₄OH/TMOS, MeOH/TMOS and H₂O/TMOS were varied from 7.1 × 10^–6 to 9.6 × 10^–1, 1 to 90 and 1 to 18 respectively. It has been found that larger molar ratios of NH₄OH/TMOS (10^–2), MeOH/TMOS (13 to 60) and H₂O/TMOS (>10) resulted in transparent but cracked aerogels, and very low molar ratios of these combinations gave monolithic but less transparent or opaque aerogels. The best quality silica aerogels, in terms of monolithicity, transparency and low density, have been obtained with TMOS:MeOH:H₂O:NH₄OH in the molar ratio of 1:12:4:3.7 × 10^–3 respectively. The aerogels have been characterized by density, optical transmission, surface area and porosity measurements. The results have been discussed by taking into account the hydrolysis and condensation reactions, and syneresis effects.     

Activity coefficients of aqueous perchloric acid

Mean ionic activity coefficients for aqueous perchloric acid at 25°C were obtained from the emf of a HClO₄ concentration cell (m=1×10^–3–1.5) containing a ClO ₄ ^– ion solution electrode and a glass electrode. The results of an application of the Pitzer equations are compared with those previously reported from several different measuring methods. Perchloric acid activity coefficients have been calculated for the mixture HClO₄–NaClO₄. In both cases, good agreement has been obtained between our results and those derived from the isopiestic method.Deceased November 15, 1984.     

Preparation,Characterization and Standard enthalpy of formation of Sr2CeO4.

Sr₂CeO₄ has been prepared by sol-combustion and co-precipitate routes and the resulting products have been characterized by XRD analysis. The molar enthalpies of solution of Sr₂CeO₄(s), Sr(NO₃)₂(s) and Ce(NO₃)₃·6H₂O(s) in 0.150 dm^–3 of (4.41 mol dm–3 H₂O₂+4.23 mol dm^–3 of HNO₃) solvent as well as the molar enthalpies of solution of Sr₂CeO₄(s), SrCl₂(s) and CeCl₃(s) in 0.150 dm³ of (1.47 mol dm^–3 H₂O₂+3.05 mol dm^–3 of HClO₄) solvent have been measured using an isoperibol type calorimeter. From these results and other auxiliary data, the standard molar enthalpy of formation of Sr₂CeO₄ has been derived to be –2277.3±3.1 kJ mol^–1 at 298.15 K. This is the first reported thermodynamic data on this compound.     

The impedance behavior of the cell Au/HClO4 · 5.5 H2O/Au in the temperature range 4.2–300 K

The impedance of the cell Au/HClO₄-5.5 H₂O/Au was investigated in the frequency range 1 to 10⁵ Hz between 4.2 and 300 K. The analysis of the data enables an evaluation of important electrolyte properties such as conductivity and dielectric constant in a wide range of temperatures, predominantly in the solid state of the electrolyte HClO₄-5.5 H₂O (T_f = 228 K). The double layer capacity of the gold electrodes was also determined; it shows a qualitatively similar result compared with previous measurements. In the solid state, the ionic conductivity exhibits two distinct activation energies of 0.37 and 0.54 eV corresponding to the two phases present in HClO₄-5.5 H₂O above and below 170 K. Below 120 K the activation energy becomes very small and tends to zero around 80 K indicating possible tunneling processes in the rigid H₂O structure. At about the same temperature the dielectric constant reaches its low temperature limit with a value _∞ ≈ 11 which is considerably higher than the value of pure ice of _∞ ≈ 3.     

The Mechanism of Acid-Catalyzed Nucleophilic Substitution in Decahydro-closo-Decaborate(2–) Anions

The reactions of salts formed by the B₁₀H^2– ₁₀anion with carboxylic acids were studied. From the model systems Cat₂B₁₀H₁₀+ HCOOH (Cat = Et₄N⁺, Bu₄N⁺, Ph₄P⁺, Ph₄As⁺), several intermediates were isolated and characterized. A mechanism was proposed for the replacement of the exo-polyhedral hydrogen atoms in B₁₀H^2– ₁₀by carboxylate groups in the reactions of Cat₂B₁₀H₁₀with carboxylic acids.     

Determination of selenium at ng/g- and pg/g-levels by hydride generation-atomic absorption spectrometry in biotic materials

Summary For the determination of Se in environmentally relevant materials in the ng/g- and pg/g-range by hydride generation-AAS, H₂Se was preconcentrated on Chromosorb W at –150° C prior to its atomization in a silica tube. The individual steps of the procedure — decomposition, reduction of Se(VI) to Se(IV), generation, preconcentration and atomization of H₂Se — were optimized, partly using the radioisotope Se-75. Se was determined directly in some water samples, in human hair, finger nails and human serum after decomposition in HNO₃/ HClO₄ and combustion in oxygen, and in proteins of human serum after isotachophoretic separation and decomposition in HNO₃/HClO₄. The detection limit of the overall procedure was found to be 6 pg absolute and the linear dynamic range extends to 6 ng.

---

Bestimmung von Selen im ng/g- und pg/g-Bereich durch Hydrid-Atomabsorptionsspektrometrie in biotischen Matrices

Zusammenfassung Zur Bestimmung von Selen in umweltrelevanten Matrices im ng/g- und pg/g-Bereich durch Hydrid-AAS wurde H₂Se auf Chromosorb W bei –150° C vor der Atomisierung in der Quarzküvette angereichert. Die einzelnen Verfahrensschritte — Aufschluß, Reduktion von Se(VI) zu Se(IV), H₂Se-Entwicklung, H₂Se-Anreicherung und Atomisierung — wurden, teilweise mit dem Radioisotop Se-75, optimiert. Se wurde in einigen Wässern direkt, in Humanhaar, Fingernägeln und Humanserum nach Aufschluß in HNO₃/HClO₄ und nach Verbrennung im Sauerstoffstrom und in Proteinen von Humanserum nach isotachophoretischer Trennung und Aufschluß in HNO₃/ HClO₄ bestimmt. Die Nachweisgrenze des gesamten Verfahrens liegt bei 6 pg absolut und der lineare Bereich erstreckt sich bis 6 ng.

---

---

Dedicated to Prof. Dr. R. Bock on the occasion of his 70th birthday     

Relative reactivities of glycerophosphates towards permanganate in perchloric acid medium

Summary The reactivities of - and -glycerophosphates towards MnO ₄ ^– in HClO₄ medium have been examined. The reactions between glycerophosphates and MnO ₄ ^– are first order with respect to [glycerophosphate], [MnO ₄ ^– ] and [H⁺]. There is no evidence for cleavage of the C–O–P bond rather than the terminal –CH₂OH group being oxidized to the respective phosphoglyceraldehyde.     

Effect of preparation pH on pore structure of silica gels

Surface characterization of silica gels prepared at different gelation pH from water glass and sulphuric acid were made by argon adsorption at 77 K using continuous volumetric method. While microporous silica gels prepared in the pH range of 1–3 had BET surface areas of 504–571 m² g^–1, total pore volumes of 0.26–0.31 cm³ g^–1 and micropore volumes of 0.16–0.23 cm³ g^–1, mesoporous silica gels prepared in the pH range of 3.36–0.65 had BET surface areas of 374–530 m² g^–1 and pore volumes of 0.61–0.79 cm³ g^–1.