Superconductivity and crystallographic properties of La2 − xMxCuO4 − δ (M = Na, K)

Superconductivity and crystallographic properties of La_{2 − x}M_xCuO_{4 − δ} (M = Na, K) are studied. In the La_{2 − x}M_xCuO_{4 − δ} system, superconductivity is detected for x 0.2. Oxygen content analysis shows that the system has more oxygen vacancies than the La_{2 − x}Sr_xCuO_{4 − δ} system. These oxygen vacancies may reduce the hole concentration, and high Na-doping is needed to produce superconductivity. In the La_{2 − x}K_xCuO_{4 − δ} system, superconductivity is observed for the first time. Resistivity and magnetic susceptibility measurements show that T_c(onset) is 40 K and the Meissner volume fraction is about 4% for x = 0.7. The system changes from orthorhombic to a tetragonal K₂NiF₄ structure at x ≈ 0.3 and only tetragonal samples show superconductivity.     

Effects of cation- or oxide ion-defect on conductivities of apatite-type La–Ge–O system ceramics

A series of apatite-type La–Ge–O ceramics were prepared and their cation-defect at the 4f+6h sites and oxide ion-defect at 2a site were investigated. In La_xGe₆O_12+1.5x ceramics of x=6–12, the higher conductivities were obtained in the region of apatite composition, La_x(GeO₄)₆O_1.5x−12 (x=8–9.33), and the highest conductivity was achieved for La₉(GeO₄)₆O_1.5 (x=9), where the number of cation (La³⁺) occupying the 4f+6h sites is 9 and the number of oxide ion occupying the 2a site is 1.5. The ceramics with cation- and oxide ion-defects were La_9−0.66xSr_x(GeO₄)₆O_1.5 (x=0–1), La_9−1.33xZr_x(GeO₄)₆O_1.5 (x=0–1), La_9−xSr_x(GeO₄)₆O_1.5−0.5x (x=0–3), La_9−xZr_x(GeO₄)₆O_1.5+0.5x (x=0–1), La_x(GeO₄)_3x−21(AsO₄)_27−3xO_1.5 (x=0–3), La_x(GeO₄)_33−3x(AlO₄)_3x−27O_1.5 (x=0–3), La₉(GeO₄)_6−x (AlO₄)_xO_1.5−0.5x (x=0–3), La₉(GeO₄)_6−x(AsO₄)_xO_1.5+0.5x (x=0–1), La_9.33−xSr_x(GeO₄)₆O_2−0.5x (x=0–1.2) and La_x(GeO₄)_4.5(AlO₄)_1.5O_1.5x−12.75 (x=8.8–9.83), which were prepared by the partial substitution of La³⁺and GeO₄⁴⁻of the basic apatite La₉(GeO₄)₆O_1.5 with Sr²⁺ or Zr⁴⁺ and AlO₄⁵⁻ or AsO₄³⁻. Such substitutions lowered the conductivity of La₉(GeO₄)₆O_1.5. These results were discussed by the electrostatic interaction between Sr²⁺, Zr⁴⁺, AlO₄⁵⁻ or AsO₄³⁻ and oxide ion as a conductive species.     

Perovskite-like system (Sr,La)(Fe,Ga)O3−δ: structure and ionic transport under oxidizing conditions

The maximum solid solubility of gallium in the perovskite-type La_1−xSr_xFe_1−yGa_yO_3−δ (x=0.40–0.80; y=0–0.60) was found to vary in the approximate range y=0.25–0.45, decreasing when x increases. Crystal lattice of the perovskite phases, formed in atmospheric air, was studied by X-ray diffraction (XRD) and neutron diffraction and identified as cubic. Doping with Ga results in increasing unit cell volume, while the thermal expansion and total conductivity of (La,Sr)(Fe,Ga)O_3−δ in air decrease with gallium additions. The average thermal expansion coefficients (TECs) are in the range (11.7–16.0)×10⁻⁶ K⁻¹ at 300–800 K and (19.3–26.7)×10⁻⁶ K⁻¹ at 800–1100 K. At oxygen partial pressures close to atmospheric air, the oxygen permeation fluxes through La_1−xSr_xFe_1−yGa_yO_3−δ (x=0.7–0.8; y=0.2–0.4) membranes are determined by the bulk ambipolar conductivity; the limiting effect of the oxygen surface exchange was found negligible. Decreasing strontium and gallium concentrations leads to a greater role of the exchange processes. As for many other perovskite systems, the oxygen ionic conductivity of La_1−xSr_xFe_1−yGa_yO_3−δ increases with strontium content up to x=0.70 and decreases on further doping, probably due to association of oxygen vacancies. Incorporation of moderate amounts of gallium into the B sublattice results in increasing structural disorder, higher ionic conductivity at temperatures below 1170 K, and lower activation energy for the ionic transport.     

Effect of Cu doping in MgB2 superconductor at various processing temperatures

The effects of Cu doping in MgB₂ superconductor has been studied at different processing temperatures. The polycrystalline samples of Mg_1−xCu_xB₂ with x = 0.05 were synthesized through the in-situ solid sate reaction method in argon atmosphere at different temperature range between 800–900 °C. The samples were characterized through X-ray diffraction (XRD), Scanning Electron Microscopy (SEM) and low temperature R–T measurement techniques for the phase verification, microstructure and superconducting transition temperature, respectively. The XRD patterns of Mg_1−xCu_xB₂ (x = 0.05) do not exhibit any impurity traces of MgB₄ or MgB₆ and they show the sharp transition in the samples prepared at 850 °C. The onset transition temperature of the prepared samples is around 39 K, which is almost the same as that for the pure MgB₂. This indicates that Cu doping in MgB₂ does not affect the transition temperature. The SEM micrograph of Mg_0.95Cu_0.05B₂ has shown that the sample is dense with grain size smaller than 1 μm.     

Oxygen tracer diffusion in La1 − xSrxCoO3

Tracer diffusion of ¹⁸O in dense, polycrystalline La_1−xSr_xCoO₃ for x = 0.1 has been measured in the temperature range 400 to 600 °C and at 500 °C for x = 0.2 at an oxygen partial pressure of 1 × 10⁵ Pa. Depth profiles were obtained by secondary ion mass spectrometry. The diffusion coefficient for La_0.9Sr_0.1CoO₃ is given by D = (17–247) exp[(−232 ± 8 kJ/mole)/RT] cm²/s. This value is several orders of magnitude lower than D extrapolated from the results for x = 0.2 measured in the 700–900 °C temperature range. One possible explanation for the discrepancy is that the two measurements reflect different diffusion paths. As expected, La_0.8Sr_0.2CoO₃ exhibits a higher diffusivity at 500 °C than does La_0.9Sr_0.1CoO₃.     

Normal state magnetoresistance in stable magnetic fields up to 20 T in single crystalline La1.76Sr0.24CuO4

The in-plane normal state resistance R_n(T, H) in an overdoped La_2−xSr_xCuO₄ crystal (x = 0.24) has been measured in magnetic fields up to 20 T parallel to the c-axis. The R_n(T) curves in constant fields show a quadratic behavior in a wide range of temperature above T_c(H). Some characteristic features in R_n(H) are observed. In the low-field region R_n(H) increases with increasing H, reaches a maximum and then decreases with further increasing H. Possible origins for the observed unusual R_n(T, H) behavior are discussed.     

Oxygen permeability of La2Cu(Co)O4+δ solid solutions

Formation of the La₂Cu_1−xCo_xO_4+δ solid solutions with orthorhombic K₂NiF₄-type structure was found to be in the range of 0≤x≤0.30 at temperatures above 1270 K. Incorporating cobalt into the copper sublattice of lanthanum cuprate leads to increasing oxygen hyperstoichiometry and decreasing electrical conductivity. Thermal expansion coefficients of the La₂Cu_1−xCo_xO_4+δ (x=0.02–0.30) ceramics at 470–1100 K were calculated from the dilatometric data to vary in the range (12.2–13.2)×10⁻⁶ K⁻¹. Studying the dependence of oxygen permeation fluxes through La₂Cu(Co)O_4+δ on the membrane thickness demonstrated that the oxygen transport at the thickness values below 1 mm is limited by both surface exchange rate and bulk ionic conductivity. Oxygen permeability of the La₂Cu_1−xCo_xO_4+δ solid solutions was ascertained to increase with cobalt concentration at x=0.02–0.10 and to decrease with further dopant additions, indicating a participation of interstitial oxygen in the ionic transport.     

Effect of pressure and of oxygen content on superconductivity in the cuprate HgBa2CuO4+δ. A quantitative analysis based on indirect-exchange pairing

A quantitative analysis is presented of experimental pressure and oxygen-doping effects on the critical temperature of HgBa₂CuO_4+δ over a wide range of δ, covering both under- and overdoped compositions, on the basis of indirect-exchange pairing between conduction electrons via oxygen anions. The results clearly show that for δ 0.28, the oxygen doping process is not the same as cation doping in e.g. La_2−xSr_xCuO₄: part of the doped oxygen fulfills a double role as hole dopant and as Cooper pair mediator. Furthermore, adding or extracting oxygen under experimental conditions is accompanied by a redistribution of oxygen anions in the unit cell, to or from the neighborhood of the CuO₂ layer. This effect explains the surprisingly wide range of superconducting compositions (0.03 δ 0.40) of the system. The observed, anomalous, upward shift in thermoelectric power for δ />/ 0.28 is attributed to different sites of doped oxygen beyond that limit, affecting only hole conductivity.     

Oxygen nonstoichiometry and electrical conductivity of the solid solutions La2−xSrxNiOy (0≤x≤0.5)

Oxygen nonstoichiometry and electrical resistance of a series La_2−xSr_xNiO_y solid solutions, where x=0.0, 0.2 and 0.5 in argon flows at oxygen partial pressures 1.5, 10.2, 49.2, 100 and 286 Pa within the temperature range of 20–1050°C were studied. Nickelate oxygen desorption/sorption spectra when heating–cooling at constant rate demonstrated strong dependence of cation composition of the samples. Unlike La_1.5Sr_0.5NiO_y compounds those of La₂NiO_y and La_1.8Sr_0.2NiO_y have weakly bonded oxygen, capable to exchange reversibly with the gas phase at the temperatures higher than 250°C. The equilibrium values of oxygen nonstoichiometry and specific resistance for the these nickelates were determined at 300–1050°C and p_O2=1.5–286 Pa as a functions of temperature versus oxygen partial pressure. All nickelate studied appear to be p-type conductors with metal electric conductivity at equilibrium states.     

Electrochemical behaviour of oxygen at nickel nest cathodic material with catalyst La1−xSrxCoO3

The reduction of oxygen in the three phases gas–liquid–solid using a nickel nest as electrode with a La_1−xSr_xCoO₃ (x=0, 0.3, 0.5, 0.7, 1) series of combined oxides as a catalyst in different electrolytes of acidic H₃PO₄ or alkaline KOH, NaOH or LiOH solution at a fixed optimum oxygen flow-rate at room temperature was studied by the electrochemical method. The electrochemical parameters, such as electron transfer coefficient and exchange current density, were also determined. The La_1−xSr_xCoO₃ series of catalysts was synthesized by a solid-state reaction. XRD was used to confirm the structure of the catalyst. BET, EDS and resistivity measurements were used to investigated the electrochemical behaviour of the cathodic reduction of oxygen in the presence of the catalyst. SEM was also used to inspect the change before and after the reaction with the catalyst. The electron transfer coefficients, β, from the experiments with the various catalysts in the different alkaline electrolytes were determined as follows:

β(in KOH)>β(in NaOH)>β(in LiOH).

It was discovered that La_0.7Sr_0.3CoO₃ as a catalyst has a higher catalytic activity, a higher specific surface area, lower electrical resistivity, better stability and less agglomeration. Therefore, the above catalyst is the best catalyst for oxygen reduction of those studied.     

Metal/insulator manganite multilayers

We have studied the transport and magnetic properties of strongly textured metal/insulator La_1−xSr_xMnO₃ (x=0.4,0.1) bilayers and trilayers, grown by DC magnetron sputtering over MgO and SrTiO₃ substrates. The multilayers present transport properties similar to those of the La_0.6Sr_0.4MnO₃ films, being very sensitive to deposition conditions. Magnetic multilayers show a metal–insulator transition around T_c (250 K) and colossal magnetoresistance which is maximum around T_c. No extrinsic magnetoresistance associated with the multilayered structure was observed, probably due to the presence of ferromagnetic coupling between the metallic layers, as suggested by magnetization measurements.     

Hole distribution and madelung energy in the high-Tc oxide superconductors

Evidence is presented that in high-T_c superconductors the electrostatic interaction as expressed by the Madelung energy is the key factor in determining the charge distribution and in particular the distribution of the holes between the CuO₂-planes and other structural subunits. Specifically, this explains the phase diagram (T_c as a function of oxygen content and oxidizing power) of cation-substituted YBa₂Cu₃O_6+y and the oxygen ordering in YBa₂Cu₃O_6.5. Moreover, we argue that the dependence of T_c on strontium content in La_2−xSr_xCuO₄ is similarly due to the fact that holes go into the (La,Sr)O-sheets as well as into the CuO₂-planes.     

Properties of a large La1.92Sr0.08CuO4+δ single crystal grown by the travelling-solvent floating-zone method

A centimeter size single crystal of La_2−xSr_xCuO_4+δ (volume=1.32 cm³) with x_Sr=0.08 has been grown by the travelling-solvent floating-zone (TSFZ) method using a double ellipsoidal-type optical furnace as the heat source. The crystallised phase was checked solvent free by X-ray powder diffraction experiments, the crystal dimensions and quality being investigated by X-ray and neutron Laüe techniques. Several rocking curves of the Bragg peaks were performed by neutron diffraction giving a full width at half maximum (FWHM) of 0.200° for (006) reflection and clearly showing the presence of twin domains as expected for such an orthorhombic structure. The superconducting critical temperature of the as-grown crystal under 2 oxygen bar was determined by SQUID measurements with T_c=18–20 K. Thermal treatments at different oxygen pressures were carried out showing no significant improvement of the transition sharpness and the T_c value. Normal state susceptibility was also measured from 6 to 800 K for two different field orientations and can be interpreted as an antiferromagnetic insulating state behaviour. The resistivity measurements display an insulating behaviour perpendicular to the CuO₂ planes and a metallic behaviour in the planes, with a high anisotropy ratio R_c/R_b350 at room temperature and a zero resistivity achieved at 27 K in both directions. The specific heat measurements have revealed no anomalies in the temperature range 15–300 K.     

Dominant role of the 2D Van Hove singularity on the Fermi surface and generalized susceptibility of the quasi-2D superconductor La2−xMxCuO4 (M = Sr, Ba, …)

The dominant role of the 2D van Hove saddle point singularity on the Fermi surface (FS) and generalized susceptibility, χ(q), in the quasi-2D superconductor La_2-xM_xCuO₄ is shown for varying compositions x of divalent additions M=Sr, Ba …. Dramatic topological changes in the FS with x indicate that composition can play the role of pressure in the classic work of Lifshitz. Very close correlations of large peaks in χ(q) with Fermi surface nesting features are found, along the Γ-X and Γ-N directions in the Brillouin zone, for varying x. The peak at X and N for x=0 which apparently drives, via a soft phonon mode, the transition from the bct to the orthorhombic phase is shifted to smaller q values. These results are consistent with the semiconducting behavior of La₂CuO₄ and superconductivity when stabilized with x>0 additions. Finally, orbital frequencies (areas) and masses are given which show the range required for de Haas-van Alphen or other experiments.     

Ln1−xSrxCoO3(Ln = Sm, Dy) for the electrode of solid oxide fuel cells

The perovskite-type oxides were synthesized in the series of Ln_1−xSr_xCoO₃(Ln = Sm, Dy). The formation of solid solutions in Dy_{1 − x}Sr_xCoO₃ was limited, compared with that in Sm_{1 − x}Sr_xCoO₃. The electrical conductivities of the sintered samples were measured as a function of x in the temperature range 30 to 1000 °C. The highest conductivity of around 500 S/cm at 1000 °C was found in Sm_0.7Sr_0.3CoO₃. The reactivity of all the samples with YSZ was examined at 800–1000 °C for 96 h. The Sr-doped perovskite oxides were more reactive with YSZ and produced SrZrO₃ at 900 °C after 96 h. However, no reaction product between SmCoO₃ and YSZ was observed at 1000 °C for 96 h. The cathodic polarization of the oxide electrodes, sputtered on yttria stabilized zirconia (YSZ), was studied at 800–1000 °C in air. SmCoO₃ shows no degradation of the electrode performance at higher temperatures. The thermal expansion measurements on the sintered samples were carried out from room temperature to 1000 °C. Large thermal expansion coefficients were found in these samples.     

Oxygen diffusion and surface exchange in La1−xSrxFe0.8Cr0.2O3−δ (x=0.2, 0.4 and 0.6)

Oxygen tracer diffusion (D*) and surface exchange rate constant (k*) have been measured, using isotopic exchange and depth profiling by secondary ion mass spectrometry (SIMS), in La_1−xSr_xFe_0.8Cr_0.2O_3−δ (x=0.2, 0.4 and 0.6). Measurements were made as a function of temperature (700–1000 °C) and oxygen partial pressure (0.21–10⁻²¹ atm) in dry oxygen, water vapour and water vapour/hydrogen/nitrogen mixtures. At high oxygen activity, D* was found to increase with increasing temperature and Sr content. The activation energies for D* in air are 2.13 eV (x=0.2), 1.53 eV (x=0.4) and 1.21 eV (x=0.6). As the oxygen activity decreases, D* increases as expected qualitatively from the increase in oxygen vacancy concentration. Under strongly reducing conditions, the measured values of D* at 1000 °C range from 10⁻⁸ cm² s⁻¹ for x=0.2 to 10⁻⁷ cm² s⁻¹ for x=0.4 and 0.6. The activation energies determined at constant H₂O/H₂ ratio are 1.21 eV (x=0.2), 1.59 eV (x=0.4) and 0.82 eV (x=0.6).

The surface exchange rate constant of oxygen for the H₂O molecule is similar in magnitude to that for the O₂ molecule and both increase with increasing Sr concentration.     

Synthesis and properties of Hg0.7Pb0.3(BaSr)2Ca2Cu3Oz superconductors

We have synthesized Hg(Pb)-1223 with substitutions of Sr for Ba, i.e. Hg_0.7Pb_0.3Ba_2−xSr_xCa₂Cu₃O_z (x = 0.0–2.0) by the ampoule method. The spray-drying method and thermal decomposition under vacuum were applied for the preparation of homogeneous precursors. Samples with T_c = 110–128 K were obtained without oxygen annealing. We found that substitution of Ba by Sr remarkably relaxed the requirements on the precursors preparation and allowed their handling under ambient conditions.     

Superconducting Nd1.85Ce0.15CuO4 films grown by the pulsed electron deposition technique

Nd_1.85Ce_0.15CuO_4−δ superconducting thin films were prepared on (1 0 0) SrTiO₃ substrates by pulsed electron deposition technique without reducing atmosphere. Oxygen content is finely controlled by high temperature vacuum annealing, and optimal superconductivity has been obtained. The deposition conditions of the film are discussed in details. Higher deposition temperature and lower gas pressure result in the loss of copper and the appearance of the foreign phase Ce_0.5Nd_0.5O_1.75. High quality Nd_1.85Ce_0.15CuO_4−δ epitaxial films are deposited at 840–870 °C in the mixed gas with a ratio of O₂:Ar = 1:3.     

Disruption of antiferromagnetic order in Zn-doped La2CuO4

The magnetic phase diagram of La₂(Cu_1−xZn_x)O₄ has been determined from zero-field muon-spin-rotation (ZF-μSR) data taken at LAMPF for 0 ≤ x ≤ 0.10. Antiferromagnetic onset temperatures follow T_N(x) from susceptibility measurements on the same samples. However, the order becomes long range, as evidenced by a well-defined internal magnetic field, only at temperatures well below T_N. Extrapolation of our results yields T_N → 0 K at x = 0.11 for a single (Cu_1−xZn_x)O₂ plane, and comparison with YBa₂(Cu_1−xZn_x)₃O₆ implies identical disruption of magnetism by Zn doping in the single- and double-plane systems.     

Preparation and superconductivity of the co-doped superconductor Nd2−x−yCayCexCuO4 with T′ structure

The preparation and superconductivity of the co-doped superconductor Nd_2−x−yCa_yCe_xCuO₄ with T′ structure were studied by XRD and superconductivity measurements. The results indicate that the effect of the co-doping of Ca²⁺ and Ce⁴⁺ on T_O and the carrier type is not significant, but the effect on the range of the superconducting compositions in this system is obvious. The study of co-doped superconductors could be important for an understanding of the effect of co-doping on the carrier concentration and to explore new superconductors.