A rapid method for the determination of brominated flame retardant concentrations in plastics and textiles entering the waste stream

Due to new European legislation, products going to waste are subject to ‘low persistent organic pollutant concentration limits’. Concentrations of restricted brominated flame retardants in waste products must be determined. A rapid extraction and clean‐up method was developed for determination of brominated flame retardants in various plastics and textiles. The optimised method used vortexing and ultrasonication in dichloromethane followed by sulfuric acid clean‐up to determine target compounds. Poly‐brominated diphenyl ethers were determined by gas chromatography with mass spectrometry and hexabromocyclododecane by liquid chromatography with tandem mass spectrometry. Good recoveries of target analytes were obtained after three extraction cycles. The method was validated using poly‐propylene and poly‐ethylene certified reference materials as well as previously characterised textiles, expanded and extruded poly‐styrene samples. Measured concentrations of target compounds showed good agreement with the certified values indicating good accuracy and precision. Clean extracts provided low noise levels resulting in low limits of quantification (0.8–1.5 ng/g for poly‐brominated diphenyl ethers and 0.3 ng/g for α‐, β‐ and γ‐hexabromocyclododecane). The developed method was applied successfully to real consumer products entering the waste stream and it provided various advantages over traditional methods, including reduced analysis time, solvent consumption, minimal sample contamination and high sample throughput, which is crucial to comply with the implemented legislation.     

Analysis of PAH compounds in soil with on-line coupled pressurised hot water extraction–microporous membrane liquid–liquid extraction–gas chromatography

Pressurised hot water extraction (PHWE) was coupled on-line with microporous membrane liquid-liquid extraction (MMLLE) and gas chromatography (GC) in the analysis of polycyclic aromatic hydrocarbon (PAH) compounds in soil. The MMLLE serves as a trapping device after the PHWE. Water from PHWE is directed to the donor side of the membrane unit and the analytes are extracted to the acceptor solution on the other side of the membrane. The role of MMLLE is to clean and concentrate the extract, which is then transferred on-line to the GC via a sample loop and an on-column interface using partially concurrent solvent evaporation. Separate optimisation of MMLLE and simulations of the PHWE-MMLLE connection were carried out before the actual on-line coupling. After optimisation of the whole on-line system, the efficiencies of the PHWE-MMLLE-GC and PHWE-solid-phase trap extractions were compared. The PHWE-MMLLE-GC method allowed on-line analysis of soil samples. The method was linear, with limits of detection in the range 0.05-0.13 ng and limits of quantification 0.65-1.66 microg g(-1). Comparison of the results with those obtained by other techniques confirmed the good performance.     

Determination of polybrominated diphenyl ethers at trace levels in environmental waters using hollow-fiber microporous membrane liquid-liquid extraction and gas chromatography-mass spectrometry

In this study, we present a simple and easy-to-use extraction method that is based on a hollow-fiber microporous membrane liquid-liquid extraction (HF-MMLLE), as an extraction technique, followed by gas chromatography-mass spectrometry (GC-MS) to determine a group of brominated flame retardants (BFRs), polybrominated diphenyl ethers (PBDEs), at trace levels in aqueous samples. The hollow-fiber membrane (HF) filled with organic solvent was immersed into the aqueous sample, spiked with the analytes at ng l(-1) level, and stirred for 60 min. The proposed method could attain enrichment factors (E(e)) up to 5200 times, after optimising parameters, such as organic solvent, stirring speed and extraction time, that affect the extraction. The HF-MMLLE-GC-MS method was successfully applied to the extraction of PBDEs from tap, river and leachate water samples with spike recoveries ranging from 85% to 110%. The method validation with reagent and leachate water samples provided good linearity, detection limits of 1.1 ng l(-1) or lower, both in reagent and leachate water, as well as satisfactory precision in terms of repeatability and reproducibility with values of % relative standard deviation (%RSD) lower than 8.6 and 16.9, respectively.     

Book Reviews

A gas chromatography/ion trap mass spectrometry method was used for the trace analysis of atrazine and its deethylated degradation product deethylatrazine in environmental water and sediment samples. The isotope dilution technique was applied for the quantitative analysis of atrazine at parts-per-trillion levels. Water samples were pre-concentrated by solid-phase extraction using a C18 cartridge while the sediment samples were extracted by sonication with methanol. The concentrated extracts were analysed by a GC/ion trap MS operated in the MS/MS method. The extraction recoveries for the analytes were better than 83% when 1 L of water or 10 g of sediment was analysed. The method detection limits were 0.75 ng/L and 0.13 ng/g for atrazine and deethylatrazine detected in water and sediment, respectively. The precisions of the method represented by the relative standard deviation were in the range of 3.2-16.1%. The method was successfully applied to analyse surface water and sediment samples collected from Beijing Guanting reservoir. Trace levels of atrazine at 35.9-217.3 ng/L and 2.4-8.4 ng/g were detected in the water and sediment samples, respectively. The levels of deethylatrazine were five to 20 times lower that those of atrazine.     

New approach based on solid-phase microextraction to estimate polydimethylsiloxane fibre coating-water distribution coefficients for brominated flame retardants

A depletion solid-phase microextraction (SPME) method based on multiple SPME extraction was applied to estimate fibre coating-water distribution constants (Kfs) of brominated flame retardants. Several polybrominated diphenyl ethers (PBDEs) including compounds present in the commercial mixture "Pentamix", and two polybrominated biphenyls (PBBs) were considered as target analytes. One hundred-micrometer poly(dimethylsiloxane) (PDMS) coating fibre was selected to estimate partition coefficients. SPME kinetics studies at 25 and 100 degrees C were performed. Kfs values obtained at both temperatures for brominated flame retardants were compared with the corresponding octanol-water partition coefficients (Kow) values found in literature. A linear log-log relationship between Kow with Kfs was found. To the best of our knowledge, this is the first study where brominated flame retardants Kfs values are estimated.     

Headspace solid-phase microextraction gas chromatography tandem mass spectrometry for the determination of brominated flame retardants in environmental solid samples

A headspace solid-phase microextraction gas chromatography coupled with tandem mass spectrometry (HSSPME-GC-MS-MS) methodology for determination of brominated flame retardants in sediment and soil samples is presented. To the best of our knowledge, this is the first time that SPME has been applied to analyze polybrominated biphenyls (PBBs) and polybrominated diphenyl ethers (PBDEs) in environmental solid samples. Analyses were performed using 0.5-g solid samples moisturized with 2 mL water, employing a polydimethylsiloxane (PDMS) fiber coating, exposed to the headspace at 100 °C for 60 min. Several types of environmental solid samples were included in this study and the extraction efficiency was related to the organic matter content of the sample. Calibration was performed using real samples, and the method showed good linearity over a wide concentration range, precision, and afforded quantitative recoveries. The obtained detection limits were in the sub-ng g⁻¹ for all the target analytes in both samples. The proposed procedure was applied to several marine and river sediments and soils, some of which were found to contain PBDEs at concentrations in the ng g⁻¹ level; BDE-47, BDE-100, and BDE-99 were the major congeners detected. The proposed method constitutes a rapid and low-cost alternative for the analysis of the target brominated flame retardants in environmental solid samples, since the clean-up steps, fractionation, and preconcentration of extracts inherent to the classical multi-step solvent extraction procedures are avoided.      

Development of a solid-phase microextraction method for the analysis of phenolic flame retardants in water samples

A solid-phase microextraction (SPME) method for the ultra-trace determination of brominated phenols in aqueous samples has been developed and is reported for the first time to the best of our knowledge. 3,5,3',5'-tetrabromobisphenol A (TBBPA), the most widely used brominated flame retardant, and other phenolic flame retardants in commercial use, such as 2,4-dibromophenol (2,4-DBP), 2,4,6-tribromophenol (TBP) and pentabromophenol (PBP) have been included as target analytes. The analytical procedure involves the in situ acetylation-SPME and gas chromatography-mass spectrometry (GC-MS) determination of the target analytes. A multi-factor categorical experimental design was created to study the main parameters affecting the extraction efficiency, allowing also the evaluation of interaction effects between factors. The factors studied were type of fiber, extraction mode, exposing the fiber directly into the sample (DSPME) or into the headspace over the sample (HSSPME), and extraction temperature. Carboxen-polydimethylsiloxane (CAR-PDMS) fiber appeared to be the most suitable of the five fibers tested for the extraction of most compounds, excluding PBP and TBBPA for which polydimethylsiloxane (PDMS) was the most efficient coating. The highest response was achieved for both fibers sampling in headspace mode at 100 degrees C. In order to test the linearity of the method, calibration studies were performed with both CAR-PDMS and PDMS coatings. For both fibers, the method was linear in a range of 2 orders of magnitude, giving relative standard deviation (RSD%) below 10% for most compounds and detection limits at the low pg/mL level. In addition, the feasibility of the method for simultaneous determination of chlorinated and brominated phenols was studied. Finally, the method was applied to several real samples including tap water and effluent and influent waste water samples from an urban treatment plant, in which several phenolic compounds, such as phenol, methylphenols and chlorophenols, could be detected and quantified.     

凝胶渗透色谱-固相萃取结合色谱-质谱法测定乳制品中18种溴系阻燃剂

采用索氏提取、凝胶渗透色谱和固相萃取技术作为前处理方法,建立乳制品中6种新型溴系阻燃剂、8种多溴联苯醚、四溴双酚A和α、β、γ-六溴环十二烷异构体共18种溴系阻燃剂的同时提取与净化方法,并结合气相色谱-负化学源质谱法(GC-NCI/MS)和高效液相色谱-电喷雾电离-串联质谱法(HPLC-ESI-MS/MS)进行检测。奶样经冷冻干燥后以正己烷-丙酮(1：1, V/V)索氏提取,采用凝胶渗透色谱结合酸化硅胶柱净化,随后以LC-Si固相萃取柱分离气相和液相待测物。以GC-NCI/MS测定6种新型溴系阻燃剂和8种多溴联苯醚,以HPLC-MS/MS检测四溴双酚A和六溴环十二烷异构体,内标法定量。结果表明,以空白牛奶样品为加标基质,多数待测物平均回收率为80.1%~114.7%,方法具有良好的精密度(多数待测物相对标准偏差( RSD)在0.87%~14.9%)和灵敏度(检出限在0.2~119.2 pg/g之间),可满足乳制品中多种溴系阻燃剂同时提取、净化和检测需求。     

Development of pressurized liquid extraction and solid‐phase microextraction combined with gas chromatography and flame photometric detection for the determination of organophosphate esters in sediments

Organophosphate esters have been extensively used as flame retardants and plasticizers. The analysis of organophosphate esters in the environment is a hot topic because many of them are toxic and persistent. We developed a novel procedure for determining organophosphate esters in sediment. In this work, pressurized liquid extraction and solid‐phase microextraction are used for sample preparation to extract and concentrate the analytes, which are then analyzed by gas chromatography with flame photometric detection. The extraction parameters of pressurized liquid extraction were investigated and optimized by orthogonal design and then evaluated by range analysis and analysis of variance. Under the optimal conditions, the proposed procedure showed wide linear ranges (0.90–100 ng/g) with correlation coefficients ranging from 0.9921 to 0.9990. The detection limits of the method were in the range of 0.009–0.280 ng/g with standard deviations ranging from 2.2 to 9.5%. Recoveries of the proposed method ranged from 82.3 to 108.9% with relative standard deviations <8.4%. The obtained method was applied successfully to the determination of organophosphate esters in real sediments with recoveries varying from 79.8 to 107.3%. The proposed method was proved to be simple, easy, and sensitive for analyzing organophosphate esters in sediment samples.     

气相色谱法测定纺织品中的三种有机磷阻燃剂

建立了超声萃取-毛细管气相色谱-氮磷检测器测定纺织品中3种有机磷阻燃剂的方法。正交试验确定超声萃取的优化条件为萃取溶剂丙酮和正己烷的体积比为2∶8,萃取时间为40 min,溶剂体积为35 mL。实验结果表明,三(2-氯乙基)磷酸酯、三邻甲苯基磷酸酯和三(2,3-二溴丙基)磷酸酯等3种化合物的线性范围分别为0.3758～36.38 mg/L、0.3841～38.41 mg/L和15.78～1010 mg/L,检测限依次为0.044,0.053和0.82 mg/kg。对于上述3种化合物,方法的精密度分别为6.2%,7.7%和6.5%,方法的回收率介于83.2%和115.4%之间。     

Optimization and Simultaneous Determination of Alkyl Phenol Ethoxylates and Brominated Flame Retardants in Water after SPE and Heptafluorobutyric Anhydride Derivatization followed by GC/MS

A gas chromatography–mass spectrometry (GC–MS) method was investigated for the simultaneous analysis of two types of endocrine disrupting compounds (EDCs), i.e., alkylphenol ethoxylates and brominated flame retardants (BFRs), by extraction and derivatization followed by GC–MS. Different solid phase extraction (SPE) cartridges (Cleanert PestiCarb, C₁₈, Cleanert-SAX and Florosil), solvents (toluene, tetrahydrofuran, acetone, acetonitrile and ethyl acetate) and bases (NaHCO₃, triethylamine and pyridine) were tested and the best chromatographic analysis was achieved by extraction with Strata-X (33?μm, Reverse Phase) cartridge and derivatization with heptafluorobutyric anhydride at 55?°C under Na₂CO₃ base in hexane. It was observed that APE together with lower substituted PBBs (PBB1, PBB10, PBB18 and PBB49), HBCD and TBBPA can be determined simultaneously under the same GC conditions. This simple and reliable analytical method was applied to determining trace amounts of these compounds from wastewater treatment plant samples. The recoveries of the target compounds from simulated water were above 60?%. The limit of detection ranged from 0.01 to 0.15?μg L^?1 and the limit of quantification ranged from 0.05 to 0.66?μg L^?1. There were no appreciable differences between filtered and unfiltered wastewater samples from Leeuwkil treatment plant although concentration of target analytes in filtered influent was slightly lower than the concentration of target analytes in unfiltered influent water. The concentrations of the target compounds from the wastewater treatment were determined from LOQ upwards.     

Concurrent extraction,clean‐up,and analysis of polybrominated diphenyl ethers,hexabromocyclododecane isomers,and tetrabromobisphenol A in human milk and serum

A method has been developed and validated for the concurrent extraction, clean‐up, and analysis of polybrominated diphenyl ethers (PBDEs), α‐, β‐, and γ‐hexabromocyclododecane (HBCD), and tetrabromobisphenol A (TBBPA) in human milk and serum. Milk and serum samples were extracted using accelerated solvent extraction with acetone/hexane 1:1, v/v and liquid–liquid extraction with methyl‐tert‐butyl ether/hexane 1:1, v/v, respectively. The removal of co‐extracted biogenic materials was achieved by gel permeation chromatography followed by sulfuric acid treatment. The fractionation of the PBDEs and HBCD/TBBPA was performed using a Supelco LC‐Si SPE cartridge. The detection of the PBDEs was then performed by GC–MS and that of the HBCDs and the TBBPA was performed using UPLC–MS/MS. The pretreatment procedure was optimized, and the characteristic ions and fragmentation of the analytes were studied by MS or MS/MS. A recovery test was performed using a matrix spiking test at concentrations of 0.05–10 ng/g. The recoveries ranged from 78.6–108.8% with RSDs equal to or lower than 14.04%. The LODs were 1.8–60 pg/g. The usefulness of the developed method was tested by the analysis of real human samples, and several brominated flame retardants in different samples were detected and analyzed.     

On-line coupling of immunoaffinity-based solid-phase extraction and gas chromatography for the determination of s-triazines in aqueous samples

The potential of immunoaffinity-based solid-phase extraction (IASPE) coupled on-line to gas chromatography (GC) for the determination of micropollutants was studied with emphasis on the interfacing of the immunoaffinity-based SPE and GC parts of the system. The cartridge containing the immobilized antibodies was coupled to the gas chromatograph via a reversed-phase cartridge (copolymer sorbent). After trace enrichment of the analytes on the immunoaffinity cartridge, they were desorbed and recollected on the reversed-phase cartridge by means of an acidic buffer. After clean-up and drying with nitrogen, desorption and transfer to the GC was done with ethyl acetate via an on-column interface in the partially concurrent solvent evaporation mode. The antibodies used in the immunoaffinity cartridge were raised against atrazine; several s-triazines were used as test compounds. Triazines that were structurally similar to atrazine, showed quantitative recovery. As an application, immunoaffinity SPE–GC was used for the analysis of river and waste water and orange juice. The selectivity of the system was such that non-selective flame ionization detection (FID) could be used to detect the analytes of interest in these complex matrices. The detection limits for 10-ml water samples were 15–25 ng/l for FID and about 1.5 ng/l for the nitrogen–phosphorus detection.     

Development of continuous on-line purge and trap analysis

An on-line purge and trap system for continuous monitoring of Volatile Organic Compounds (VOC) is presented. The purge chamber was designed for continuous extraction of VOC from water with nitrogen. The analytes were preconcentrated on a microtrap prior to analysis by GC with flame ionization detection. The microtrap served as a fast injection device for carrying out analysis at high frequency. Continuous monitoring was accomplished by performing injections at fixed intervals. This system showed high sensitivity, high precision, detection limits at the ppb level, and stable response over long periods of continuous operation. Factors affecting system performance were studied. A predictive model based on gas-liquid partitioning is also presented.     

Simultaneous use of gas chromatography/ion trap mass spectrometry - electron capture detection to improve the analysis of bromodiphenyl ethers in biological and environmental samples

Bromodiphenyl ethers (BDEs) are a class of synthetic flame retardants and are widely present in the environment. Analysis of higher BDE congeners has proven to be a challenge. We report the development of a method that enhances their analysis by splitting the eluent of a gas chromatograph (GC) between an electron capture detector (ECD) and an ion trap mass spectrometer (ITMS): 1:10, ECD:ITMS. This allowed the quantitation of the lower molecular weight (MW) BDE congeners (Br1-Br7) with the ITMS and of the higher MW BDEs (Br8-Br10) with the highly sensitive ECD. The IT temperature, ionization mode, and MS/MS parameters (excitation amplitude and stability parameter) were optimized. This method took the advantages of the best detector for the different BDE homologues and was suitable for the analysis of BDEs in environmental and biological samples. Average recoveries were 52-112% for BDEs from spiked sand samples and 57-126% from spiked lard samples after accelerated solvent extraction followed by silica gel and alumina column clean-up. Average recoveries ranged from 51% to 130% for 13C-labeled BDEs spiked in the real and in matrix samples. The method detection limits for specific congeners were 0.18-120 pg/g of the BDEs in animal tissue samples, and 0.05-40 pg/g in soil and indoor dust samples. The utility of the method was demonstrated by analyzing actual harbor seal blubber, indoor dust and soil samples. The concentration of each BDE ranged from non-detectable (nd) to 41 ng/g in the dry soil sample, nd to 1042 ng/g in the indoor dust, nd to 15 ng/g wet weight in the Alaskan harbor seal blubber sample, and 0.02 to 11 ng/microL of the identified 23 of the 42 breakdown products from BDE-209 after zerovalent iron treatment. Finally, an interlaboratory comparison showed high correspondence between the GC/ITMS-ECD method and a GC high-resolution MS system for the analysis of BDEs in soil samples.     

Brominated flame retardants in laboratory air

During the development of a method for determination of brominated flame retardants in human plasma and serum using solid-phase extraction, several brominated flame retardants were found in the procedural blanks. The contaminants originated most probably from the laboratory air. The brominated flame retardants were found to be adsorbed on glass surfaces and to be acquired using solid-phase sampling. 2,4,6-Tribromophenol, 2,2',4,4'-tetrabromodiphenyl ether (BDE-47) and 2,2',4,4',5-pentabromodiphenyl ether (BDE-99) were the most abundant brominated flame retardants in our laboratory air, however, large differences in contamination with respect to sampling time and place were observed.     

Microwave-assisted extraction of organophosphate flame retardants and plasticizers from indoor dust samples

A procedure for the determination of eight organophosphate flame retardants and plasticizers in dust samples is presented. Microwave-assisted extraction and gas chromatography (GC) with nitrogen-phosphorus detection (NPD) were used for sample preparation and analytes quantification, respectively. Influence of different variables (type and volume of organic solvent, temperature, time, agitation, etc.) on the yield of the extraction step was evaluated. The most important factor was the type of solvent, with the highest efficiencies corresponding to acetone. Under final conditions 10 mL of this solvent were employed. The extraction was carried out at 130 degrees C and satisfactory yields, similar to those obtained with the Soxhlet technique, were achieved. Due to the high content of organic carbon in dust samples, primary acetone extracts had to be subjected to intensive clean-up. Dilution with ultrapure water followed by concentration on a reversed-phase sorbent and further purification using silica, allowed a significant reduction of co-extracted interferences. Application of the developed methodology to indoor dust from private houses showed important concentrations of several organophosphate esters. The highest levels, up to 19 microg/g, corresponded to tris(butoxyethyl) phosphate; moreover, average values of two chlorinated compounds, used as flame retardants and considered as the most concerning species in the group, exceeded the 1 microg/g level.     

A Total Solution to Baseline Separation of 20 Brominated Flame Retardant Additives in Electronic Products with Automated Soxhlet Hot Extraction and Gas Chromatography‐Mass Spectrometry

An efficient and reliable separation technique based on automated Soxhlet hot extraction (AHSE) was developed and validated. It can be applied to rapid separations of 20 persistent organic pollutants, including two types of brominated flame retardants (BFRs), polybrominated biphenyls (PBBs) and polybrominated diphenyl ethers (PBDEs) contained in nonmetallic component parts of electronic products. The qualitative chromatographic analyses were carried out by using a gas chromatography coupled with a mass spectrometry detector (GC‐MS). The 20 persistent organic pollutants were simultaneously and completely separated by a 15 meter HP‐5MS short capillary column in 25 minutes. Through the tests of extraction performance, effects of solvent and extraction time on selected BFRs were investigated; toluene and 120 min extraction time were chose as the optimum conditions. Besides, this article examines the influence of temperature on the chromatographic analysis, the optimum temperature parameters were 280 °C and 320 °C for injector and column, respectively. The ASHE‐GCMS method was validated for the analysis of the certified reference material of CRM8110‐a and IRMM310. The limits of detection (LOD) for polymer sample was 0.55‐4.50 μg mL^?1; linearity range from 0.11 to 16 μg mL^?1. The proposed methodology can fully meet the requirement of relational directives.     

Optimization and Simultaneous Determination of Alkyl Phenol Ethoxylates and Brominated Flame Retardants in Water after SPE and Heptafluorobutyric Anhydride Derivatization followed by GC/MS

A gas chromatography–mass spectrometry (GC–MS) method was investigated for the simultaneous analysis of two types of endocrine disrupting compounds (EDCs), i.e., alkylphenol ethoxylates and brominated flame retardants (BFRs), by extraction and derivatization followed by GC–MS. Different solid phase extraction (SPE) cartridges (Cleanert PestiCarb, C₁₈, Cleanert-SAX and Florosil), solvents (toluene, tetrahydrofuran, acetone, acetonitrile and ethyl acetate) and bases (NaHCO₃, triethylamine and pyridine) were tested and the best chromatographic analysis was achieved by extraction with Strata-X (33 μm, Reverse Phase) cartridge and derivatization with heptafluorobutyric anhydride at 55 °C under Na₂CO₃ base in hexane. It was observed that APE together with lower substituted PBBs (PBB1, PBB10, PBB18 and PBB49), HBCD and TBBPA can be determined simultaneously under the same GC conditions. This simple and reliable analytical method was applied to determining trace amounts of these compounds from wastewater treatment plant samples. The recoveries of the target compounds from simulated water were above 60 %. The limit of detection ranged from 0.01 to 0.15 μg L⁻¹ and the limit of quantification ranged from 0.05 to 0.66 μg L⁻¹. There were no appreciable differences between filtered and unfiltered wastewater samples from Leeuwkil treatment plant although concentration of target analytes in filtered influent was slightly lower than the concentration of target analytes in unfiltered influent water. The concentrations of the target compounds from the wastewater treatment were determined from LOQ upwards.

     

Extraction of brominated flame retardants from polymeric waste material using different solvents and supercritical carbon dioxide

Different procedures were examined to extract pure and high concentrations of a series of brominated flame retardants from various polymer materials. These procedures include supercritical carbon dioxide (sc-CO₂), modified sc-CO₂, solvent and soxhlet extraction. Extraction with sc-CO₂ gave low extraction efficiencies (between 6 and 20%) probably due to the low pressure of sc-CO₂ used. The use of toluene, acetonitrile and THF as modifier in sc-CO₂ raised the extraction efficiencies for many flame retardants. High extraction efficiencies were achieved for tetrabromobisphenol A (TBBPA), TBBPA-bis-(2,3-dibromopropylether) (TBBPA-dbp), TBBPA-carbonatoligomer (TBBPA-co) and decabromodiphenylether (DECA) (between 93 and 100%) by using 1-propanol as solvent during soxhlet extraction. Toluene instead of 1-propanol was used where insufficient extraction of the flame retardant occurred. The materials (before and after extraction) were analysed with energy dispersive X-ray fluorescence analysis (EDXRF), high performance liquid chromatography with ultraviolet detection (HPLC/UV), gas chromatography/mass spectrometry (GC/MS) and infrared spectroscopy (IR) techniques. The properties of the extracted flame retardants such as TBBPA, TBBPA-dbp and 1,2-bis(tribromophenoxy)-ethane (TBPE) are in good agreement with those of standard reference materials.