Atom-trapping absorption spectrometry with water-cooled metal collector tubes

Water-cooled metal collector tubes for atom-trapping atomic absorption spectrometry in air—acetylene flames are discussed, particularly for the more volatile elements such as cadmium and selenium which may be less efficiently trapped at the hotter surface of a silica tube. It was found that a nickel tube gave 3 times greater sensitivity than silica for the determination of cadmium but was oniy half as sensitive for the determination of selenium. No atomic absorption signal for copper could be obtained with a nickel collector tube. A copper tube was 3–4 times more sensitive than nickel for cadmium and selenium. Similar effects were observed for cadmium solutions containing 1000 ppm copper or nickel, and for selenium solutions containing 1000 ppm copper, with silica atom-trap tubes, but in both cases better results were obtained when the analyte solution of cadmium or selenium contained the co-element (1000 ppm) than when the cadmium or selenium was measured with a silica tube previously metallized with the co-element.     

Determination of cadmium in sewage sludge by differential pulse anodic stripping voltammetry

A procedure was developed for the determination of cadmium in sewage sludge by differential pulse anodic stripping voltammetry. A sodium peroxide fusion carried out in zirconium crucibles was found to give satisfactory results, based on analysis of standard reference materials. Samples collected from the municipal sludge lagoon in Fort Wayne, Indiana were found to have cadmium abundances ranging from 120 to 250 ppm, with most samples falling in the 120 to 170 ppm range. Interference from zinc is easily eliminated by carrying out the deposition step at -0.95 V vs. Ag/AgCl. Lead-to-cadmium ratios as high as 50:1 (ppm basis) have no effect on the height of the cadmium peak.     

Determination of traces of cadmium in alloy steels by anodic stripping voltammetry

Concentrations of cadmium of the order of 0.1 ppm in alloy steels containing large concentrations of chromium and nickel (ca. 17 and 13% respectively), about 0.1% of copper and a number of metals at low concentrations, were determined by anodic stripping voltammetry with a hanging mercury-drop electrode in 1M hydrochloric acid. Cadmium was separated on Dowex 50W-X8 cation-exchanger in a medium at pH 1.3 containing excess of EDTA. Mercury-film electrodes cannot be used for this determination, because the peak for cadmium is distorted by evolution of hydrogen on the electrode support. The relative standard deviation of the determination of 0.44 ppm of cadmium in steel is 3.2% and the confidence limits for 95% probability are 0.44 +/- 0.02 ppm. The error in the cadmium recovery does not exceed + 8%.     

Revisiting the calculation of (13)C chemical shift tensors in cadmium acetate dihydrate with EIM and EIM/cluster methods

The chemical shift tensors of the acetate anions in cadmium acetate dihydrate are calculated using a cluster approach, the embedded ion method (EIM), and a combination of the two in the EIM/cluster method. The results of these calculations are compared with those completed on the isolated acetate anion and show the need for the inclusion of intermolecular interactions. The RMS difference between experiment and theory improves from over 60 ppm when the calculation is completed on an isolated anion, to below 10 ppm when interactions to nearby atoms are included. The best cluster model includes three cadmium acetate dihydrate and gives an RMS result of 4.4 ppm. The EIM method, which uses point charges to account for the intermolecular effects, achieves an RMS of 7.7 ppm on individual anions alone. A combination of the two, the EIM/cluster method, shows that the only necessary atom to explicitly add is the nearest cadmium; this addition results in an RMS of 4.1 ppm. These results are also discussed in terms of the computational cost of the different calculations.     

Simultaneous determination of lead and cadmium in various environmental and biological samples by differential pulse polarography after adsorption of their morpholine-4-carbodithioates onto microcrystalline naphthalene or morpholine-4-dithiocarbamate-CTMAB-naphthalene adsorbent

A highly selective, sensitive and rapid differential pulse polarographic method (DPP) has been developed for the simultaneous estimation of trace amounts of lead and cadmium in standard alloys, biological and environmental samples. The morpholine-4-carbodithioates of the samples were absorbed on microcrystalline naphthalene in the pH range of 5-10 for lead and 3.4-11 for cadmium. The metal complexes were desorbed with 10 ml of 1M HCl and determined simultaneously with a differential pulse polarograph. These metals can alternatively be quantitatively adsorbed on morpholine-4-dithiocarbamate-cetyltrimethylammonium bromide-naphthalene adsorbent packed in a column and determined similarly. The detection limits are 0.14 ppm for Pb and 0.014 ppm for Cd at minimum instrumental settings (signal-to-noise ratio = 2). The linearity is maintained in the concentration ranges of Pb, 0.7-15 ppm and Cd, 0.07-10 ppm with a correlation factor of 0.9997 and relative standard deviations of 0.95 and 0.81%, respectively. Various parameters such as the effect of pH, volume of aqueous phase, and interference of a number of metal ions on the estimation of lead and cadmium have been studied in detail to optimize the conditions for their simultaneous estimation in various biological and environmental samples.     

A study of differential potentiometric stripping analysis for lead and cadmium with Nafion coated carbon fibre electrode

The differential potentiometric stripping analysis (DPSA) with Nafion coated carbon fibre electrode has been studied, and a method to determine lead and cadmium in urine directly has been attempted. The effect of various experimental parameters on the DPSA response is discussed. The experimental conditions include 0.2M sodium perchlorate, deposition potential of ?1.0 or ?1.1 V and using 20 ppm mercuric ion as oxidizing agent. The response of the signal is in linear relation with the concentrations of lead and cadmium respectively up to 0.5 ppm. The electrode coated with Nafion film alleviates the interference from organics in urine samples.     

Dynamics of mononuclear cadmium beta-lactamase revealed by the combination of NMR and PAC spectroscopy

The two metal sites in cadmium substituted beta-lactamase from Bacillus cereus 569/H/9 have been studied by NMR spectroscopy ((1)H, (15)N, and (113)Cd) and PAC spectroscopy ((111m)Cd). Distinct NMR signals from the backbone amides are identified for the apoenzyme and the mononuclear and binuclear cadmium enzymes. For the binuclear cadmium enzyme, two (113)Cd NMR signals (142 and 262 ppm) and two (111m)Cd PAC nuclear quadrupole interactions are observed. Two nuclear quadrupole interactions are also observed, with approximately equal occupancy, in the PAC spectra at cadmium/enzyme ratios < 1; these are different from those derived for the binuclear cadmium enzyme, demonstrating interaction between the two metal ion binding sites. In contrast to the observation from PAC spectroscopy, only one (113)Cd NMR signal (176 ppm) is observed at cadmium/enzyme ratios < 1. The titration of the metal site imidazole (N)H proton signals as a function of cadmium ion-to-enzyme ratio shows that signals characteristic for the binuclear cadmium enzyme appear when the cadmium ion-to-enzyme ratio is between 1 and 2, whereas no signals are observed at stoichiometries less than 1. The simplest explanation consistent with all data is that, at cadmium/enzyme ratios < 1, the single Cd(II) is undergoing exchange between the two metal sites on the enzyme. This exchange must be fast on the (113)Cd NMR time scale and slow on the (111m)Cd PAC time scale and must thus occur in a time regime between 0.1 and 10 micros.     

Effect of certain chemical compounds on secondary metabolites of Penicillium janthinellum and P. duclauxii

The secondary metabolites of Penicillium janthinellum and P. duclauxii were affected by different concentrations of cadmium nitrate, sodium chloride, and sucrose. The fungal culture characteristics including mycelial fresh and dry weight, colony diameter, colony spore mass and reverse color, number of spores, and secondary metabolites were affected as well. Cyclopenin, carlosic acid, erythroskyrin, kojic acid, and patulin were produced by P. janthinellum on cadmium nitrate-free medium. However, cyclopenin, carlosic acid, frequentin, and islandicin were produced at 100 ppm, and cyclopenin at 500 ppm. On the other hand, the secondary metabolites produced by P. duclauxii were 9 on cadmium nitrate-free medium, 7 on medium containing 100 and 500 ppm of cadmium nitrate, and 4 at 1000 ppm cadmium nitrate concentration. Secondary metabolite brevianamide A was produced in the presence and absence of cadmium nitrate. The duclauxin, patulin, terrestic acid, and xanthomegin were produced only on cadmium nitrate-free medium. However, mycophenolic acid was produced only on cadmium nitrate-containing medium. The kojic acid was produced by P. janthinellum at 0.0%, 0.5%, 1.0%, 2.0%, 3.0%, and 5.0% concentrations of sodium chloride. The carlosic acid, erythroskyrin, and patulin were produced only at 0.0% and 1.0%. While carolic acid and islandicin were produced at 1%, 2%, and 3% and frequentin was produced only at 2% and 3%. On the other hand, 8 secondary metabolites were produced by P. duclauxii at 0.0%, 0.5%, 1.0%, and 2.0% concentration of sodium chloride and only 4 were produced at 3%. The secondary metabolites produced by P. janthinellum were 7 at 10% and 20%, 6 at 30%, and 2 only at 40% concentrations of sucrose. However, 8 secondary metabolites were produced by P. duclauxii at 10%, 20%, 30% and 3 at 40% concentrations of sucrose.     

Polarographic Determination of Low Concentrations of Nitrilotriacetate in Lake Water

Abstract

Samples of lake water containing NTA in concentrations from 1 to 10 ppm have been analysed by a polarographic method. The NTA was converted to its 1:1 cadmium complex by adding a 100% excess of cadmium. The method can be used also when sodium tripolyphosphate and sodium alkylbenzenesulphonate are present in the sample.     

Biosorption of Cadmium by Phanerochaete Chrysosporium

The biosorption properties of cadmium(Ⅱ) by pre-treated biomass of Phanerochaete chrysosporium in the form of pellet were investigated. It was found that formaldehyde cross-linking and subsequent alkaline treatment could significantly improve the adsorption capacity of the biomass compared to other sorts of treatments, such as calcium chloride treatment, HCl treatment and,acetone treatment. Biosorption capacity of cadmium was examined as a function of physical and chemical factors including the pH of the metal solution pellet size, temperature and biomass concentration. The cadmium removal efficiency was strongly affected by pH. The maximal adsorption occurred around pH4.5. The pellet size also had a marked influence on the cadmium removal efficiency and the optimum size was the diameter range of 1.5-2.0 mm. The effect of biosorption temperature on cadmium uptake was inconspicuous between 25℃ and 35℃, but there was a notable decrease in cadmium uptake when the temperature reached 40℃. The cadmium removal efficiency increased as the biomass concentration when the initial cadmium ion concentration was 10 mg/L. When the biomass concentration was 2 g/L,the removal efficiency was 99.56%. However, the augment of the. removal efficiency was not obvious when the biomass concentration was more than 2 g/L. On the optimum conditions mentioned above,cadmium concentration could be reduced from 10 ppm down to 0.04 ppm that was below the Chinese National Waste Water Integrated Discharge Standard. In the biosotption process, most of the metal uptake happened during a short period immediately after the adsorption process started. It was observed that the biomass pellets had already adsorbed 83.36% of the total amount of cadmium finally adsorbed within the initial 10 minutes. The cadmium uptake rate decreased gradually afterwards. Sorption equilibrium could almost be established in 12 hours. This indicated that biosorption might consist of two processes:a fast surface binding process opcurring first and a slow membrane diffusion process taking place subsequently.     

Indirect atomic-absorption determination of boron by solvent extraction as tris(1,10-phenanthroline)cadmium tetrafluoroborate

An indirect atomic-absorption method for boron has been developed. Boric acid is converted into tetrafluoroborate and extracted into nitrobenzene with Tris(1,10-phenanthroline)cadmium(II). The cadmium in the extract is determined by its atomic-absorption at 228s>d8 nm. A fivefold molar excess of the cadmium chelate is necessary for the extraction from pH 4>d3-6>d0 medium. The sensitivity for boron is thus made about the same as that of cadmium, 0>d005 ppm. Metal ions that react with fluoride or phenanthroline interfere. A procedure is described for determination of boron in steel.     

Automated determination of nitrate in waters with a reduction column in a microcomputer-based stopped-flow sample processing system

An automated method for the determination of nitrate in waters with a microcomputer-based stopped-flow mixing system is described. Nitrate is reduced to nitrite with a copperized cadmium—silver alloy or cadmium tube column fitted to the stopped-flow system. Nitrite is determined using fast kinetic, multi-point or single-point procedures with N-(1-naphthyl)ethylenediamine dihydrochloride as the color reagent. Reduction time parameters are evaluated and optimized. Water samples in the range of 0.025–3 ppm NO^-₃—N can be processed with a throughput of up to 100 samples per hour and a detection limit of 0.013 ppm. Interference studies show that cyanide; dichromate, iodide, sulfide, copper and tin ions cause negative results.     

113Cd Shielding Tensors of Monomeric Cadmium Compounds Containing Nitrogen Donor Atoms. 3. CP/MAS Studies on Five-Coordinate Cadmium Complexes Having N(3)X(2) (X = H, N, O, and S) Donor Atoms

The principal elements of the (113)Cd shielding tensor for a set of five- coordinate compounds having mixed donor atoms coordinating to the cadmium were determined via CP/MAS NMR experiments. The first complex, [HB(3,5-Me(2)pz)(3)]CdBH(4) (where pz = pyrazolyl), has a CdN(3)H(2) inner coordination sphere. The isotropic chemical shift in the solid state is 355.1 ppm, and its chemical shift anisotropy (CSA, Deltasigma) is -596 ppm with an asymmetry parameter (eta) of 0.64. The second complex, [HB(3,5-Me(2)pz)(3)]Cd[H(2)B(pz)(2)], has five nitrogen donor atoms bonded to the cadmium. This N(5) or N(3)N(2) compound was the only material of this study to manifest dipolar splitting of the cadmium resonance from the quadrupolar (14)N. The isotropic chemical shift, CSA, and the value of eta for this material were therefore determined at higher field where the dipolar splitting was less than the linewidth, yielding values of 226.6 ppm, -247 ppm, and 0.32, respectively. A second N(5) material, [HB(3-Phpz)(3)]Cd[H(2)B(3,5-Me(2)pz)(2)], was also investigated and has an isotropic shift of 190.2 ppm, a CSA of 254 ppm, and an eta of 0.86. Also studied was [HB(3-Phpz)(3)]Cd[(Bu(t)CO)(2)CH], which has an CdN(3)O(2) inner core. The isotropic chemical shift of this complex is 173.6 ppm, and the values of Deltasigma and eta were determined to be -258 ppm and 0.38, respectively. The final compound, [HB(3,5-Me(2)pz)(3)]Cd[S(2)CNEt(2)], with N(3)S(2) donor atoms, has an isotropic shift of 275.8 ppm, an eta of 0.51, and a CSA of +375 ppm. Utilizing previous assignments, the most shielded tensor element was determined to be oriented normal to the plane of the tridentate ligand. The shielding tensor information is used to speculate on the coordination geometry of the CdN(3)O(2) inner core complex.     

Nitrogen distribution measurements by neutron induced autoradiography

A method utilizing plastic track detectors was developed to determine the nitrogen distribution and concentration in the presence of boron in metals. Experiments were performed at the UVAR (cadmium ratio ≈25) and the NIST Reactor (cadmium ratio ≈3000). The minimum detectable concentration of nitrogen at a given concentration of boron has been estimated using the detector’s response to¹⁰B(n,α)⁷ Li reaction products in terms of track size distribution. The capability of the technique to detect nitrogen in the presence of boron has been demonstrated using 316L stainless steel with a nitrogen concentration of ≈560 ppm and a boron concentration of ≈0.86 ppm.     

Determination of Au,Sb, As,Br, Na,K, Cd,Mn and Cl in rice from Vietnam by neutron activation analysis

Gold, antimony, arsenic, bromine, sodium, potassium, cadmium, manganese and chlorine were determined by neutron activation analysis in various rice seed, brand layer and husk from Vietnam. The following concentration values were found: Au 0.05–0.28 ppm, Sb 0.05–1.08 ppm, As 0.08–0.94 ppm, Br 0.82–6.72 ppm, Na 16.71–25, 71 ppm, K 2582–5163 ppm, MN 19.26–33.43 ppm, Cd 0.51–2.42 ppm and Cl 205.20–828.61 ppm in rice seed. These elements were also determined in brand layer and rice husk. Statistically significant differences /t=0.05/ in Au, Sb, Cd contents were detected in rice seed and rice husk, as well as brand layer with rice husk.     

Bestimmung von kleinen Cadmium-Gehalten in Uranoxid durch Neutronenaktivierungsanalyse

Zusammenfassung Cadmiumspuren (10ppb-5ppm) in Uranoxid wurden durch Neutronenaktivierungsanalyse bestimmt. Einer Vortrennung des Cadmiums vom Uran durch Anionenaustausch mit Dowex 1 folgte die Bestrahlung auf dem Austauscherharz im FR 2. Die erzeugten Cadmium-Aktivitäten konnten durch einen kurzen chemischen Trennungsgang nach der Bestrahlung radiochemisch rein erhalten werden. Nach Korrektur der chemischen Ausbeuten verhielten sich die Aktivitäten proportional den eingesetzten Cadmiummengen.

---

Determination of small amounts of cadmium in uranium oxide by neutron-activation analysis

A pre-separation of cadmium from uranium by anion-exchange on Dowex-1 was followed by irradiation on the exchange resin in the FR-2. The cadmium activities produced could be obtained radiochemically pure by a short chemical separation procedure after irradiation. After correction of the chemical yields the activities were proportional to the original cadmium content. 10 ppb-5 ppm of Cd could be determined.

---

---

Herrn Dr. A. v. Baeckmann danke ich für wertvolle Hinweise, Frau M. Friedrich für ihre tatkräftige Mithilfe bei der Durchführung dieser Arbeit.     

Cadmium recovery by a sulfate-reducing magnetotactic bacterium,Desulfovibrio magneticus RS-1, using magnetic separation

Cadmium recovery by a sulfate-reducing magnetotactic bacterium, Desulfovibrio magneticus strain RS-1, was investigated. D. magneticus precipitated >95% of cadmium at an initial concentration of 1.3 ppm in the growth medium. Electron microscopic analysis revealed that D. magneticus formed electron-dense particles on its surface when cultivated in the presence of cadmium ions (Cd²⁺). Sulfide was also found in the precipitate, and the composition ratio of sulfide/cadmium was 0.7. Sixty percent of viable RS-1 cells was recovered by a simple magnetic separation revealing the removal of 58% cadmium from the culture medium.     

Analysis of toxic elements by MPGA

In order to improve the sensitivity for the quantification of trace elements, we propose the combination of prompt gamma-ray analysis (PGA) and a multiple gamma-ray detection method. A new Ge detector system for multiple prompt gamma-ray analysis (MPGA) was constructed at the neutron guide-hall of the JRR-3M reactor of the Japan Atomic Energy Agency (JAEA). The first demonstration of this system was given with a plastic sample containing traces of cadmium. The quantification limit of cadmium in a plastic sample was found to be about 0.1 ppm.     

Spectrophotometr1c determination of cadmium with 2-(5-chloro-2-pyridylazo)-5-dimethylaminophenol

The reaction between cadmium and 2-(5-chloro-2-pyridylazo)-5-dimethylaminophenol (5-Cl DMPAP) in aqueous alcohol media at pH 8.8-10.7 results in an intense violet colour which is stable for at least 8 hr. The composition is 2:1 reagent:metal and the formation constant (5.29 +/- 0.01) x 10(18). Beer's law is obeyed up to 1.34 ppm of cadmium at 550 nm. The optimal concentration range (Ringbom) is between 0.16 and 0.72 ppm. The apparent molar absorptivity at 550 nm is (1.20 +/- 0.01) x 10(5) l.mole(-1). cm(-1), making the sensitivity one of the highest known. The interference due to copper(III), iron(III), cobalt(II), nickel(II), gold(III), zinc(II) and manganese(II) can be suppressed.     

Atomic Absorption Spectrometry Analysis of Silicates by the Absorption Tube Technique

Abstract

By the combined use of the absorption tube technique and solvent extraction, determination of cadmium, cobalt, copper, iron, lead and nickel in silicate rocks was investigated.

Applicable concentration range was from 0.1 to 1.Oppm for all the elements except cadmium, for which the range was from 0.005 to 0.025ppm. The accuracy and recovery determined by the use of standard samples from the United States National Bureau of Standards and Geological Survey were satisfactory for practical purposes.