Development of electrochemical DNA biosensor for Trichoderma harzianum based on ionic liquid/ZnO nanoparticles/chitosan/gold electrode

Electrochemical DNA biosensor was successfully developed by depositing the ionic liquid (e.g., 1-ethyl-3-methylimidazolium trifluoromethanesulfonate ([EMIM][Otf])), ZnO nanoparticles, and chitosan (CHIT) nanocomposite membrane on a modified gold electrode (AuE). The electrochemical properties of the [EMIM][Otf]/ZnO/CHIT/AuE for detection of DNA hybridization were studied. Under optimal conditions using cyclic voltammetry, the target DNA sequences could be detected in the concentration range of 1.0 × 10⁻¹⁸ to 1.82 × 10⁻⁴ mol L⁻¹, and with the detection limit of 1.0 × 10⁻¹⁹ mol L⁻¹. This DNA biosensor detection approaches provide a quick, sensitive, and convenient method to be used in the identification of Trichoderma harzianum.     

Measurement of binding kinetics between PI3-K and phosphorylated IGF-1R using a surface plasmon resonance biosensor

A high-performance amperometric glucose biosensor was developed, based on immobilization of glucose oxidase (GOx) on a copper (Cu) nanoparticles/chitosan (CHIT)/carbon nanotube (CNT)-modified glassy carbon (GC) electrode. The Cu and CNT had a synergistic electrocatalytic effect toward the reduction of hydrogen peroxide in the matrix of biopolymer CHIT. The Cu/CHIT/CNT modified GC electrode could amplify the reduction current of hydrogen peroxide greatly. Besides, the Cu/CHIT/CNT modified GC electrode reduces hydrogen peroxide at a much lower applied potential and inhibit the responses of interferents. With GOx as an enzyme model, a new glucose biosensor was fabricated. The sensitivity of the sensor is due not only to the large microscopic area but also to the high efficiency of transformation of H₂O₂ generated by enzymatic reaction to current signal. The biosensor exhibited excellent sensitivity (the detection limit is down to 0.02 mM), fast response time (less than 4 sec), wide linear range (from 0.05 to 12 mM), and perfect selectivity. Correspondence: Wanzhi Wei, State key Laboratory of Chemo/Biosensing and Chemometrics, College of Chemistry and Chemical Engineering, Hunan University, Changsha 410082, China     

Enzyme biosensor based on the immobilization of HRP on SiO<Subscript>2</Subscript>/BSA/Au composite nanoparticles

In this work, an enzyme biosensor based on the immobilization of horseradish peroxidase (HRP) on SiO₂/BSA/Au/thionine/nafion-modified gold electrode was fabricated successfully. Firstly, nafion was dropped on the surface of the gold electrode to form a nafion film followed by chemisorption of thionine (Thi) as an electron mediator via the ion-exchange interaction between the Thi and nafion. Subsequently, the SiO₂/BSA/Au composite nanoparticles were assembled onto Thi film through the covalent bounding with the amino groups of Thi. Finally, HRP was immobilized on the SiO₂/BSA/Au composite nanoparticles due to the covalent conjugation to construct an enzyme biosensor. The surface topographies of the SiO₂/BSA/Au composite nanoparticles were investigated by using scanning electronic microscopy. The stepwise self-assemble procedure of the biosensor was further characterized by means of cyclic voltammetry and chronoamperometry. The enzyme biosensor showed high sensitivity, good stability and selectivity, a wide linear response to hydrogen peroxide (H₂O₂) in the range of 8.0 × 10^-6 ∼ 3.72 × 10^-3 mol/L, with a detection limit of 2.0 × 10^-6 mol/L. The Michaelies-Menten constant K_M^app K_M^{app} value was estimated to be 2.3 mM.     

A non-enzymatic sensor for hydrogen peroxide based on polyaniline, multiwalled carbon nanotubes and gold nanoparticles modified Au electrode

We describe the construction of a polyaniline (PANI), multiwalled carbon nanotubes (MWCNTs) and gold nanoparticles (AuNPs) modified Au electrode for determination of hydrogen peroxide without using peroxidase (HRP). The AuNPs/MWCNT/PANI composite film deposited on Au electrode was characterized by Scanning Electron Microscopy (SEM) and electrochemical methods. Cyclic voltammetric (CV) studies of the electrode at different stages of construction demonstrated that the modified electrode had enhanced electrochemical oxidation of H(2)O(2), which offers a number of attractive features to develop amperometric sensors based on split of H(2)O(2). The amperometric response to H(2)O(2) showed a linear relationship in the range from 3.0 μM to 600.0 μM with a detection limit of 0.3 μM (S/N = 3) and with high sensitivity of 3.3 mA μM(-1). The sensor gave accurate and satisfactory results, when employed for determination of H(2)O(2) in milk and urine.     

Electrocatalytic sulfite biosensor with human sulfite oxidase co-immobilized with cytochrome c in a polyelectrolyte-containing multilayer

An efficient electrocatalytic biosensor for sulfite detection was developed by co-immobilizing sulfite oxidase and cytochrome c with polyaniline sulfonic acid in a layer-by-layer assembly. QCM, UV–Vis spectroscopy and cyclic voltammetry revealed increasing loading of electrochemically active protein with the formation of multilayers. The sensor operates reagentless at low working potential. A catalytic oxidation current was detected in the presence of sulfite at the modified gold electrode, polarized at +0.1 V (vs. Ag/AgCl 1 M KCl). The stability of the biosensor performance was characterized and optimized. A 17-bilayer electrode has a linear range between 1 and 60 μM sulfite with a sensitivity of 2.19 mA M⁻¹ sulfite and a response time of 2 min. The electrode retained a stable response for 3 days with a serial reproducibility of 3.8% and lost 20% of sensitivity after 5 days of operation. It is possible to store the sensor in a dry state for more than 2 months. The multilayer electrode was used for determination of sulfite in unspiked and spiked samples of red and white wine. The recovery and the specificity of the signals were evaluated for each sample. Figure Schematic of the bioelectrocatalytic sulfite sensor: sulfite oxidase (green) oxidizes sulfite to sulfate and transfers electrons via heme b ₅ to cyt c (red) and thence to the gold electrode     

A novel hydrogen peroxide sensor based on Ag nanoparticles electrodeposited on chitosan-graphene oxide/cysteamine-modified gold electrode

A novel strategy to fabricate a hydrogen peroxide sensor based on Ag nanoparticles electrodeposited on chitosan-graphene oxide nanocomposites/cysteamine-modified gold (Au) electrode was reported. The chitosan-graphene oxide nanocomposites were first assembled on a cysteamine-modified Au electrode to produce chitosan-graphene oxide/cysteamine/Au electrode. Then Ag nanoparticles were electrodeposited on the modified Au electrode and formed Ag nanoparticles/chitosan-graphene oxide/cysteamine/Au electrode. The chitosan-graphene oxide nanocomposites and the electrodeposited Ag nanoparticles were characterized by atomic force microscopy and scanning electron microscopy. The results showed the Ag nanoparticles were uniformly dispersed on the chitosan-graphene oxide/cysteamine/Au electrode. The cyclic voltammagrams and amperometric method were used to evaluate electrocatalytic properties of the Ag nanoparticles/chitosan-graphene oxide/cysteamine/Au electrode. The results showed that the modified electrode displayed good electrocatalytic activity to the reduction of hydrogen peroxide with a detection limit of 0.7 μM hydrogen peroxide based on a signal-to-noise ratio of 3. The sensor has good reproducibility, wide linear range, and long-term stability.     

Fabrication of gold nanoparticles/polypyrrole composite-modified electrode for sensitive hydroxylamine sensor design

A highly sensitive hydroxylamine (HA) electrochemical sensor is developed based on electrodeposition of gold nanoparticles with diameter of 8 nm on the pre-synthesized polypyrrole matrix and formed gold nanoparticles/polypyrrole (GNPs/PPy) composite on glassy carbon electrode. The electrochemical behavior and electrocatalytic activity of the composite-modified electrode are investigated. The GNPs/PPy composite exhibits a distinctly higher electrocatalytic activity for the oxidation of HA than GNPs with twofold enhancement of peak current. The enhanced electrocatalytic activity is attributed to the synergic effect of the highly dispersed gold metal particles and PPy matrix. The overall numbers of electrons involved in HA oxidation, the electron transfer coefficient, catalytic rate constant, and diffusion coefficient are investigated by chronoamperometry. The sensor presents two wide linear ranges of 4.5 × 10⁻⁷–1.2 × 10⁻³ M and 1.2 × 10⁻³–19 × 10⁻³ M with the detection limit of 4.5 × 10⁻⁸ M (s/n = 3). In addition, the proposed electrode shows excellent sensitivity, selectivity, reproducibility, and stability properties.     

Lable‐Free Electrochemical DNA Sensor Based on Gold Nanoparticles/Poly(neutral red) Modified Electrode

We present a new strategy for the label‐free electrochemical detection of DNA hybridization based on gold nanoparticles (AuNPs)/poly(neutral red) (PNR) modified electrode. Probe oligonucledotides with thiol groups at the 5‐end were covalently linked onto the surface of AuNPs/PNR modified electrode via S‐Au binding. The hybridization event was monitored by using differential pulse voltammetry (DPV) upon hybridization generates electrochemical changes at the PNR‐solution interface. A significant decrease in the peak current was observed upon hybridization of probe with complementary target ssDNA, whereas no obvious change was observed with noncomplementary target ssDNA. And the DNA sensor also showed a high selectivity for detecting one‐mismatched and three‐mismatched target ssDNA and a high sensitivity for detecting complementary target ssDNA, the detection limit is 4.2×10^?12 M for complementary target ssDNA. In addition, the DNA biosensor showed an excellent reproducibility and stability under the DNA‐hybridization conditions.     

壳聚糖-纳米金-葡萄糖氧化酶生物传感器的制备及其应用于葡萄糖的测定

采用了一种简便快捷的电沉积方法制备了壳聚糖-纳米金复合膜并应用于葡萄糖生物传感器的构建.氯金酸和壳聚糖的混合液在玻碳电极表面电化学还原为金纳米粒子,再将葡萄糖氧化酶通过戊二醛交联的方式固定在纳米金复合膜修饰的玻碳电极表面,制成一种新型的葡萄糖氧化酶生物传感器.该传感器对葡萄糖的响应十分快速,在5 S内即达到平衡.测定葡萄糖的线性范围为20μmol·L-1～5 mmol·L-1,检出限(3S/N)为12μmol·L-1.     

Synthesis of polyaniline/Au composite nanotubes and their high performance in the detection of NADH

Polyaniline (PANI)/Au composite nanotubes were synthesized and developed as an electrode material for a nicotinamide adenine dinucleotide (NADH) sensor. A MnO₂ self-degradable template method was used to prepare the tube-like PANI nanomaterial. By introducing PANI nanotubes into Au colloid, Au nanoparticles (NPs) were successfully decorated onto the surface of PANI nanotubes through electrostatic effects. The morphology, composition, and optical properties of the resulting products were characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, ultraviolet-visible (UV-vis) absorption spectra, and thermogravimetric analysis (TGA). In addition, the obtained PANI/Au composites were used as catalysts for the electrochemical oxidation of NADH. Cyclic voltammogram (CV) experiments indicated that PANI/Au-modified glassy carbon electrode showed a higher electrocatalytic activity towards the oxidation of NADH in a neutral environment. Differential pulse voltammogram (DPV) results illustrated that the fabricated NADH sensor had excellent anti-interference ability and displayed a wide linear range from 4?×?10^?4 to 8?×?10^?3 M with a detection limit of 0.5?×?10^?7 M.     

基于AuNPs/PANI/TNTs纳米复合材料的电化学检测妥布霉素的适配体传感器

本文提出了一种新型的检测妥布霉素的电化学适配体传感器,以差分脉冲伏安法（DPV）作为检测技术,亚甲基蓝作为电化学响应信号. 构建了以纳米复合材料金纳米粒子/聚苯胺/二氧化钛纳米管(AuNPs/PANI/TNTs)修饰玻碳电极的电极支架. 通过透射电子显微镜和X-射线光电子能谱对纳米复合材料进行详细的表征. 循环伏安图和电化学阻抗谱显示AuNPs/PANI/TNTs可以很好地增加电极的界面传导性能. DPV结果显示电流密度的响应和妥布霉素浓度之间存在一个很好的线性关系,并且得到一个宽广的检测范围为0.5 μmol·L^-1到70 μmol·L^-1. 本文提出的适配体基的传感器有很好的重复性和稳定性,作为一个潜在的手段可以应用在生物分析和医疗诊断中.     

Synergistic contributions of multiwall carbon nanotubes and gold nanoparticles in a chitosan–ionic liquid matrix towards improved performance for a glucose sensor

We report an ingenious approach for the fabrication of a promising glucose sensor, GOx/Au/CS–IL–MWNT(SH), that exploits the synergistic beneficial characteristics of multiwalled-carbon nanotubes (MWNTs), gold nanoparticles (AuNPs), chitosan (CS) and room temperature ionic liquid (RTIL). Direct electron transfer between glucose oxidase (GOx) and electrode was achieved. Scanning electron microscopy and atomic force microscopy images of GOx/Au/CS–IL–MWNT(SH) reveal that MWNTs and AuNPs are dispersed in CS–IL matrix. Cyclic voltammetry, impedance spectroscopy and chronoamperometry were used to evaluate the performance of biosensor. The GOx/Au/CS–IL–MWNT(SH) biosensor exhibits a linear current response to glucose concentration (1–10 mM) at a low potential of 0.10 V and precludes interferences from uric acid and ascorbic acid. The GOx/Au/CS–IL–MWNT(SH) biosensor has superior performances over GOx/CS–IL–MWNT(SH).     

A high-sensitive amperometric hydrogen peroxide biosensor based on the immobilization of hemoglobin on gold colloid/L-cysteine/gold colloid/nanoparticles Pt-chitosan composite film-modified platinum disk electrode

A hemoglobin (Hb)/gold colloid (nano-Au)/L-cysteine (L-cys)/nano-Au/nanoparticles Pt (nano-Pt)-chitosan (CHIT) composite film-modified platinum disk electrode (abbreviated to modified electrode) has been prepared to construct a biosensor for determination of H(2)O(2). The electrochemical characteristics of the biosensor were studied by cyclic voltammetry and chronoamperometry. The modified process was characterized by electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The morphologies of different composite film were investigated with scanning electron microscopy (SEM) and the element of composite film was investigated with X-ray photoelectron spectroscopy (XPS). Analytical parameters such as pH and temperature were also studied. The linear range for the determination of H(2)O(2) is 1.4 x 10(-7) to 6.6 x 10(-3)mol/L with a detection limit of 4.5 x 10(-8)mol/L (S/N=3). The sensor achieved 95% of the steady-state current within 10s. The sensor exhibited high sensitivity (17.62 microA/(mmol L)), selectivity and stability. The method is applied to the determination of H(2)O(2) with satisfactory results.     

Electrochemical detection of phenolic compounds using composite film of multiwall carbon nanotube/surfactant/tyrosinase on a carbon paste electrode

A new tyrosinase-based biosensor was developed for detection of phenolic compounds using composite film of multiwall carbon nanotube (MWCNT)/dimethylditetradecylammonium bromide (DTDAB)/tyrosinase (Tyr) on a Nafion-incorporated carbon paste electrode. The biosensor showed a sensitive electrochemical response to the reduction of the oxidation products of different phenolic compounds (phenol, catechol, p-cresol, and p-chlorophenol) by dissolved O₂ in the presence of the immobilized enzyme. The effects of pH, operating potential, MWCNT concentration, and the DTDAB/Tyr ratio on electrochemical response were explored for optimum analytical performance. The biosensor exhibited a linear response range of 1.5–25.0, 2.0–15.0, 2.0–15.0, and 2.5–25.0 μM and sensitivity of 2,900, 3,100, 3,100, and 1,500 μA/mM for phenol, catechol, p-cresol, p-chlorophenol, respectively. In addition, the response of the enzyme electrode showed Michaelis–Menten behavior at concentrations of the phenolic compounds higher than 5.0 μM. The stability and the application of the biosensor were also evaluated.     

Amperometric determination of xanthine in fish meat by zinc oxide nanoparticle/chitosan/multiwalled carbon nanotube/polyaniline composite film bound xanthine oxidase

Xanthine oxidase (XOD) was immobilized on a composite film of zinc oxide nanoparticle/chitosan/carboxylated multiwalled carbon nanotube/polyaniline (ZnO-NP/CHIT/c-MWCNT/PANI) electrodeposited over the surface of a platinum (Pt) electrode. A xanthine biosensor was fabricated using XOD/ZnO-NP/CHIT/c-MWCNT/PANI/Pt as working electrode, Ag/AgCl as reference electrode and Pt wire as auxiliary electrode connected through a potentiostat. The ZnO-NPs were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM), and the enzyme electrode was characterized by cyclic voltammetry, scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy and electrochemical impedance spectroscopy (EIS). The biosensor showed optimum response within 4 s at 0.5 V potential, pH 7.0, 35 °C and linear range 0.1-100 μM with a detection limit of 0.1 μM. The enzyme electrode was employed for determination of xanthine in fish meat during storage. The electrode lost 30% of its initial activity after 80 uses over one month, when stored at 4 °C.     

Direct detection and discrimination of double-stranded oligonucleotide corresponding to hepatitis C virus genotype 3a using an electrochemical DNA biosensor based on peptide nucleic acid and double-stranded DNA hybridization

Development of an electrochemical DNA biosensor for the direct detection and discrimination of double-stranded oligonucleotide (dsDNA) corresponding to hepatitis C virus genotype 3a, without its denaturation, using a gold electrode is described. The electrochemical DNA sensor relies on the modification of the gold electrode with 6-mercapto-1-hexanol and a self-assembled monolayer of 14-mer peptide nucleic acid probe, related to the hepatitis C virus genotype 3a core/E1 region. The increase of differential pulse voltammetric responses of methylene blue, upon hybridization of the self-assembled probe with the target ds-DNA to form a triplex is the principle behind the detection and discrimination. Some hybridization experiments with non-complementary oligonucleotides were carried out to assess whether the developed DNA sensor responds selectively to the ds-DNA target. Diagnostic performance of the biosensor is described and the detection limit was found to be 1.8 × 10⁻¹² M in phosphate buffer solution, pH 7.0. The relative standard deviation of measurements of 100 pM of target ds-DNA performed with three independent probe-modified electrodes was 3.1%, indicating a remarkable reproducibility of the detection method.     

Amperometric sulfite sensor based on multiwalled carbon nanotubes/ferrocene-branched chitosan composites

A novel amperometric sensor for the determination of sulfite was fabricated based on multiwalled carbon nanotubes (MWCNTs)/ferrocene-branched chitosan (CHIT-Fc) composites-covered glassy carbon electrode (GCE). The electrochemical behavior of the sensor was investigated in detail by cyclic voltammetry. The apparent surface electron transfer rate constant (K_s) and charge transfer coefficient (α) of the CHIT-Fc/MWCNTs/GCE were also determined by cyclic voltammetry, which were about 1.93 cm s⁻¹ and 0.42, respectively. The sensor displayed good electrocatalytic activity towards the oxidation of sulfite. The peak potential for the oxidation of sulfite was lowered by at least 330 mV compared with that obtained at CHIT/MWCNTs/GCE. In optimal conditions, linear range spans the concentration of sulfite from 5 μM to 1.5 mM and the detection limit was 2.8 μM at a signal-to-noise ratio of 3. The proposed method was used for the determination of sulfite in boiler water. In addition, the sensor has good stability and reproducibility.     

Thiol Modified Chitosan Self-Assembled Monolayer Platform for Nucleic Acid Biosensor

A self-assembled monolayer (SAM) of thiol modified chitosan (SH-CHIT), with thioglycolic acid (TGA) as a modifier to bestow thiol groups, has been prepared onto gold (Au)-coated glass plates for fabrication of the nucleic acid biosensor. The chemical modification of CHIT via TGA has been evidenced by Fourier transform infrared spectroscopy (FT-IR) studies, and the biocompatibility studies reveal that CHIT retains its biocompatible nature after chemical modification. The electrochemical studies conducted onto SH-CHIT/Au electrode reveal that thiol modification in CHIT amino end enhances the electrochemical behavior indicating that it may be attributed to delocalization of electrons in CHIT skeleton that participates in the resonance process. The carboxyl group modified end of DNA probe has been immobilized onto SH-CHIT/Au electrode using N-ethyl-N′-(3-dimethylaminopropyl)carbodimide (EDC) and N-hydroxysuccinimide (NHS) chemistry for detection of complementary, one-base mismatch and non-complementary sequence using electrochemical and optical studies for Mycobacterium tuberculosis detection. It has been found that DNA-SH-CHIT/Au bioelectrode can specifically detect 0.01 μM of target DNA concentration with sensitivity of 1.69?×?10^?6 A μM^?1.     

Molecularly Imprinted Electrochemical Sensor Based on Modified Reduced Graphene Oxide‐gold Nanoparticles‐polyaniline Nanocomposites Matrix for Dapsone Determination

This work was designed to develop an electrochemical sensor based on molecular imprinted polyaniline membranes onto reduced graphene oxide (RGO) and gold nanoparticles (AuNPs) modified glassy carbon (GC) electrode for dapsone (DDS) determination. The prepared RGO/AuNPs/PANI‐MIPs nanocomposite was characterized by Ultra‐Violet‐Visible (UV‐Vis), Fourier transform infrared spectroscopy (FT‐IR) and scanning electronic microscopy (SEM) images. The feature of the imprinted electrode was evaluated by cyclic voltammetry (CV), differential pulse voltammetry (DPV) and impedance spectroscopy (IS). Throughout this study several analytical parameters, such as incubation time, pH value, concentration of monomer/template molecules and electro‐polymerization cycles were investigated. Under the optimized conditions, the experimental results showed best analytical performances for DDS detection with a sensitivity of 0.188 Ω/mol L^?1, a linear range from 1.0×10^?7 M to 1.0×10^?3 M and a detection limit of 6.8×10^?7 M. The bioanalytical sensor was applied to the determination of dapsone in real samples with high selectivity and recovery.     

Hydrogen peroxide sensor based on horseradish peroxidase immobilized on a silver nanoparticles/cysteamine/gold electrode

A third-generation hydrogen peroxide biosensor was prepared by immobilizing horseradish peroxidase (HRP) on a gold electrode modified with silver nanoparticles. A freshly-cleaned gold electrode was first immersed in a cysteamine–ethanol solution, and then silver nanoparticles were immobilized on the cysteamine monolayer, and finally HRP was adsorbed onto the surfaces of the silver nanoparticles. This self-assemble process was examined via atomic force microscopy (AFM). The immobilized horseradish peroxidase exhibited an excellent electrocatalytic response toward the reduction of hydrogen peroxide. The linear range of the biosensor was 3.3 M to 9.4 mM, and the detection limit was estimated to be 0.78 M. Moreover, the biosensor exhibited a fast response, high sensitivity, good reproducibility, and long-term stability.