Novel soluble fluorinated poly(ether imide)s with different pendant groups: Synthesis,thermal, dielectric,and optical properties

Three types of new bis(ether dianhydride) monomers, [4,4′‐(2‐(3′‐methylphenyl)‐1,4‐phenylenedioxy)‐diphthalic anhydride (4a)], [4,4′‐(2‐(3′‐trifluoromethylphenyl)‐1,4‐phenylenedioxy)‐diphthalic anhydride (4b)], and [4,4′‐(2‐(3′,5′‐ditrifluoromethylphenyl)‐1,4‐phenylenedioxy)‐diphthalic anhydride (4c)] were prepared via a multistep reaction sequence. Three series of soluble poly(ether imide)s (PEIs) were prepared from the obtained dianhydrides by a two‐step chemical imidization method. Experimental results indicated that all the PEIs had glass transition temperature in the range of 200–230 °C and the temperature of 5% weight loss in the range of 520–590 °C under nitrogen. The PEIs showed excellent solubility in a variety of organic solvents due to introduction of the bulky pendant groups and were capable of forming tough films. The casting films of PEIs (80–91 μm in thickness) had tensile strengths in the range from 88 to 117 MPa, tensile modulus from 2.14 to 2.47 GPa, and elongation at break from 15 to 27%. The casting films showed UV‐Vis absorption edges at 357–377 nm, low dielectric constants of 2.73–2.82, and water uptakes lower than 0.66 wt %. The spin‐coated films of PEIs presented a minimum birefringence value as low as 0.0122 at 650 nm and low optical absorption at the optical communication wavelengths of 1310 and 1550 nm. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3281–3289, 2010     

Novel heterocyclic poly(pyridine‐imide)s with unsymmetric carbazole substituent and noncoplanar structure: High thermal,mechanical and optical transparency,electrochemical, and electrochromic properties

A diamine containing heterocyclic pyridine and unsymmetrical carbazole substituents, 4‐(9‐ethyl‐3‐carbazole)‐2,6‐bis(4‐aminophenyl)pyridine ( CBAPP ), was prepared for use in the synthesis of poly(pyridine‐imide)s PI‐1–8 by direct polycondensation with dianhydrides in N,N‐dimethylacetamide (DMAc). The poly(pyridine‐imide)s derived from the diamine are highly soluble in solvents such as N‐Methyl‐2‐pyrrolidone (NMP) and DMAc at room temperature. Noncoplanar polyimide (PI‐1) showed excellent solubility, high transparency, and high‐performance mechanical properties. These polymers had relatively high glass transition temperatures and exhibited good thermal stability in both nitrogen (T_d10 > 470 °C) and air (T_d10 > 450 °C). The PI‐3～5 cannot form flexible and tough films due to the unsymmetrical carbazole moiety, rigid structure, and polar–polar interaction. However, through copolymerization technique these polymers (PI‐6～8) could be enhanced through the solubility, mechanical, and thermal properties. The optical properties included a strong orange fluorescence (540 nm) after protonation with acid. When the HCl concentration was increased, a new absorption band at approximately 350 nm appeared, and the intensity of the fluorescent peak at 380 nm observed in the neutral polymer solution decreased, along with the appearance of the new fluorescent peak at 540 nm. The poly(pyridine‐imide)s presented here showed only slight fluorescence quenching in the presence of methanol. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 405–412     

Synthesis of a new class of triphenylamine‐containing poly(ether‐imide)s for electrochromic applications

A novel triphenylamine (TPA)‐containing bis(ether anhydride) monomer, namely 4,4′‐bis(3,4‐dicarboxyphenoxy)triphenylamine dianhydride, was synthesized and reacted with various aromatic diamines leading to a series of new poly(ether‐imide)s (PEI). Most of these PEIs were soluble in organic solvents and could be easily solution cast into flexible and strong films. The polymer films exhibited good thermal stability with glass‐transition temperatures in the range 211–299 °C. The polymer films exhibited reversible electrochemical processes and stable color changes (from transparent to navy blue) with high coloration efficiency and contrast ratio upon electro‐oxidation. During the electrochemical oxidation process, a crosslinked polymer structure was developed due to the coupling reaction between the TPA radical cation moieties in the polymer chains. These polymers can be used to fabricate electrochromic devices with high coloration efficiency, high redox stability, and fast response time. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 825–838     

Synthesis and characterization of fluorinated poly(imide siloxane) block copolymers

Five new block copoly(imide siloxane)s have been prepared by reacting two different diamines, 4,4″-bis(p-aminophenoxy)-3,3″-trifluoromethyl terphenyl (APTTFT) and amino-propyl terminated polydimethylsiloxane (APPS), separately with 4,4′-(4,4′-isopropylidenediphenoxy)bis(phthalic anhydride); BPADA. The reactions were conducted by a two pot solution imidization technique. The diamine APTTFT and the dianhydride BPADA composed the hard block segment while APPS and BPADA composed the soft block segment. The soft and hard blocks of different block lengths were generated by different stoichiometric imbalance in two different flasks and the final polymers were obtained by reacting both the blocks together. Different block copoly(imide siloxane)s were prepared on increasing the hard block lengths (DP) from 7 to 12, 18, 23 and 28 and the soft block lengths (DP) from 4 to 6, 8, 10 and 12, respectively. The resulting polymers have been well characterized by NMR, DSC and DMA techniques. The properties of the block copolymers were compared with the analogous random copolymers and homopolyimide prepared without APPS.     

Novel poly(fluorinated imide)s containing naphthalene pendant group: synthesis and characterization

A new fluorinated diamine monomer containing naphthalene pendant group, bis(4-amino-3,5-difluorophenyl)naphthylmethane (monomer 1), was synthesized from 1-naphthaldehyde and 2,6-difluoroaniline with trifluoromethanesulfonic acid at reflux. The novel poly(fluorinated imide)s (PFIs) were prepared via one-step polycondensation by monomer 1 and three aromatic dianhydrides including 4,4′-oxydiphthalic dianhydride, 3,3′,4,4′-benzophenonetetracarboxylic dianhydride, and 3,3′,4,4′-biphenyltetracarboxylic dianhydride in m-cresol, respectively. The obtained PFIs could be dissolved in a variety of organic solvents such as N-methyl-2-pyrrolidinone, N,N-dimetahylacetamide (DMAC), N,N-dimethylformamide, chloroform, and tetrahydrofuran at room temperature. The highest solubility of PFIs could even reach to 250 mg/mL in chloroform. The PFIs could be easily processed into flexible and tough films by casting onto glass from DMAC solution. The PFI films had a tensile strength, elongation at break, and tensile modulus in the range of 84–102 MPa, 8.7–12.8%, and 2.2–2.8 GPa, respectively. These polymers also showed excellent thermal stability with glass transition temperatures in the range of 326–352 °C, 10% weight loss temperatures in the range of 538–574 °C, and the weight residue more than 57% at 800 °C in nitrogen. Moreover, as for the optical properties, these PFIs exhibited a strong optical absorption in the ultraviolet region (290–370 nm) and photoluminescence in dilute chloroform solution or solid state.     

Synthesis and characterization of poly(epoxy‐imide) crosslinked networks

Poly(epoxy imide)s were prepared by a reaction between a hydroxyl‐group‐containing soluble copolyimide and commercial epoxy resins at 220 °C for 2 h. Poly(epoxy imide) thin films exhibited higher thermal stability and lower dielectric constants than a commercial flip‐chip package material (U300). The thermal stabilities of the poly(epoxy imide)s were 1.4–2.0 times higher than that of U300. The thermal stability increased with increasing crosslink density and with decreasing bulky CF₃ groups (which were easily decomposable). The dielectric constants of the poly(epoxy imide)s were 1.1–1.3 times lower than that of U300, and this is highly desirable for the microelectronic packaging industry. The dielectric constant dramatically decreased when bulky CF₃ groups were added and when the functionalities of epoxy resins decreased. The residual stresses, slopes in the cooling curves, and glass‐transition temperatures of the poly(epoxy imide)s were measured with a thin‐film stress analyzer. Low residual stresses and slopes in the cooling curves were achieved with a higher crosslink density. However, in the presence of bulky CF₃ groups, the copolyimide backbone structure did not affect the residual stress values. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4293–4302, 2004     

New organosoluble and thermally stable poly(amide‐imide)s with benzoxazole or benzothiazole pendent groups: synthesis and characterization

Two new benzoxazole or benzothiazole‐containing diimide‐dicarboxylic acid monomers, such as 2‐[3,5‐bis(N‐trimellitimidoyl)phenyl]benzoxazole ( 2 _o ) or 2‐[3,5‐bis(N‐trimellitimidoyl)phenyl]benzothiazole ( 2 _s ) were synthesized from the condensation reaction between 3,5‐diaminobenzoic acid and 2‐aminophenol or 2‐aminothiophenol in polyphosphoric acid (PPA) with subsequent reaction of trimellitic anhydride in the presence of glacial acetic acid, respectively, and two new series of modified aromatic poly(amide‐imide)s were prepared. This preparation was done with pendent benzoxazole or benzothiazole units from the newly synthesized diimide‐dicarboxylic acid and various aromatic diamines by triphenyl phosphite‐activated polycondensation. In addition, the corresponding unsubstituted poly(amide‐imide)s were prepared under identical experimental conditions for comparative purposes. Characterization of polymers was accomplished by inherent viscosity measurements, FT‐IR, UV–visible, ¹H‐NMR spectroscopy and thermogravimetry. The polymers were obtained in quantitative yields with inherent viscosities between 0.39 and 0.81 dl g^?1. The solubilities of modified poly(amide‐imide)s in common organic solvents as well as their thermal stability were enhanced compared to those of the corresponding unmodified poly(amide‐imide)s. The glass transition temperature, 10% weight loss temperature, and char yields at 800°C were, respectively, 7–26°C, 17–46°C and 2–5% higher than those of the unmodified polymers. Copyright © 2010 John Wiley & Sons, Ltd.     

Novel polyimides with p-nitrophenyl pendant groups. Synthesis and characterization

Polyimides derived from a new dianhydride with p-nitrophenyl pendant groups have been synthesized and their properties compared with those of a reference series, without side groups. The polymers were obtained by combination of the novel monomer with aromatic diamines, in a two-step procedure that involved the synthesis of poly(amic acid) or poly(amic silyl ester) intermediates and the cyclization of them to polyimides by thermal treatment. The introduction of the polar nitro groups caused significant increase of the T_gs. On the contrary, the thermal stability was reduced because of the breakdown of C_Ar—NO₂ linkages around 400^oC. A slight decrease in mechanical properties was observed, due to the bulkiness of the side groups, that also produced an important decrease in the strength of the β relaxation, as determined by dynamic mechanical analysis. The solubility of the current polyimides in organic solvents was as poor as that of the parent unsubstituted polymers. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3377–3384, 1999     

Synthesis and characterization of hyperbranched aromatic poly(ether imide)s with terminal amino groups

We synthesized an AB₂‐type monomer, 4‐{4‐[di(4‐aminophenyl)methyl]phenoxy}phthalic acid, which contained one phthalic acid group and two aminophenyl functionalities. The direct self‐polycondensation of the AB₂‐type monomer in the presence of triphenylphosphite as an activator afforded a hyperbranched poly(ether imide) with a large number of terminal amino groups. This polymer was characterized with ¹H NMR and IR spectroscopy. The degree of branching of the hyperbranched poly(ether imide) was approximately 56%, as determined by a combination of model compound studies and an analysis of ¹H NMR spectroscopy integration data. The terminal amino groups underwent functionalization readily. The solubility and thermal properties of the resulting polymers depended on the nature of the chain end groups. In addition, the hyperbranched poly(ether imide) was grafted with polyhedral oligomeric silsesquioxane (POSS). Transmission electron microscopy analysis revealed that the grafted POSS molecules aggregated to form a nanocomposite material. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3726–3735, 2003     

Synthesis and characterization of photocrosslinkable,side‐chain,second‐order nonlinear optical poly(ester imide)s with great film‐forming ability and long‐term dipole orientation stability

A series of photocrosslinkable, side‐chain, second‐order nonlinear optical (NLO) poly(ester imide)s (PEIs) based on a chromophore‐containing dianhydride, 2,2′‐{4‐[(4‐nitrophenyl)‐azo]phenyl}iminobis(ethyl benzene‐1,2‐dicarboxylic acid anhydride‐4‐carboxylate), benzophenone‐3,3′,4,4′‐tetracarboxylic dianhydride, and 4,4′‐diamino‐3,3′‐dimethyl diphenylmethane were prepared. The resulting PEIs exhibited many useful physical characteristics, such as good organosolubility, excellent film‐forming properties, high glass‐transition temperatures (186–229 °C), and high thermal decomposition temperatures. The electrooptic coefficient value of PEI3 at 650 nm was 11.5 pm/V, and high long‐term stability of the NLO chromophore alignment in the poled PEI3 film at 120 °C was observed. The temporal stability of the dipole orientation at 150 °C was further enhanced by ultraviolet irradiation because of photocrosslinking. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 303–312, 2003     

Synthesis and photoluminescent and electrochromic properties of aromatic poly(amine amide)s bearing pendent N‐carbazolylphenyl moieties

A series of novel poly(amine amide)s ( IIa – IIl ) with pendent N‐carbazolylphenyl units having inherent viscosities of 0.25–1.06 dL/g were prepared via direct phosphorylation polycondensation from various dicarboxylic acids and a carbazole‐based aromatic diamine. Except for poly(amine amide) IIc , derived from trans‐1,4‐cyclohexanedicarboxylic acid, all the other amorphous poly(amine amide)s were readily soluble in many polar solvents, such as N,N‐dimethylacetamide and N‐methyl‐2‐pyrrolidone (NMP), and could be cast into transparent and flexible films. The aromatic poly (amine amide)s had useful levels of thermal stability associated with relatively high glass‐transition temperatures (268–331 °C), 10% weight loss temperatures in excess of 540 °C, and char yields at 800 °C in nitrogen higher than 60%. These polymers exhibited maximum ultraviolet–visible absorption at 293–361 nm in NMP solutions. Their photoluminescence in NMP solutions exhibited fluorescence emission maxima around 362 and 448–499 nm for aromatic–aliphatic poly(amine amide)s IIa – IIc and aromatic poly (amine amide)s IId – IIl , respectively. The fluorescence quantum yield in NMP solutions ranged from 0.34% for IIj to 4.44% for IIa . The hole‐transporting and electrochromic properties were examined with electrochemical and spectroelectrochemical methods. Cyclic voltammograms of the poly(amine amide) films cast onto an indium tin oxide coated glass substrate exhibited reversible oxidation at 0.81 V and irreversible oxidation redox couples at 1.20 V versus Ag/AgCl in acetonitrile solutions, and they revealed excellent stability of the electrochromic characteristics, with a color change from yellow to green at applied potentials ranging from 0.00 to 1.05 V. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4108–4121, 2006     

Novel processable and heat resistant poly(phenylthiourea azomethine imide)s: Synthesis and characterization

N-(4-chloro-3-aminobenzal)N′(4-aminophenyl)thiourea having phenylthiourea and azomethine groups was synthesized and exploited as starting material for the fabrication of new polymers. Novel diamine was condensed with pyromellitic dianhydride, 3,3′,4,4′-benzophenone-tetrcarboxylic dianhydride and 4,4′-(hexafluoroisopropylidene) diphthalic dianhydride to obtain poly(phenylthiourea azomethine imide)s. The structural explication of monomers and poly(phenylthiourea azomethine imide)s were carried out by FTIR, ¹H and ¹³C NMR techniques along with crystallinity, organosolubility, inherent viscosity and molecular weight measurements. Accordingly, polymers bearing CS and -CN- moieties in the backbone demonstrated an amorphous nature and were readily soluble in amide solvents such as DMAc, DMF, and DMSO. Poly(phenylthiourea azomethine imide)s encompassed η_inh of 1.40-1.55 dL/g and were obtained in quantitative yields. In addition, GPC measurements of polymers revealed M_w around 60,291-67,665. Thermal stability of these polymers was ascertained via 10% weight loss temperatures around 514-533 °C in an inert atmosphere. Besides, glass transition temperatures of polyimides were found to be 272-276 °C.     

Synthesis,characterization and thermal behaviour of some poly(2-vinyl pyridine) complexes

Poly(2-vinyl pyridine) complexes were prepared via quaternization of the ring nitrogen with different reagents (I₂, Br₂, Cl₂, CrO₃, picric acid and HgCl₂). The thermal behaviour of these polymer complexes, such as E and the order of decomposition, were studied by using the modified Freeman and Carroll procedure. Generally, it was found that the presence of a substituent on the nitrogen in the polymer lowers the activation energy and the thermal stability.

---

Zusammenfassung Durch Quaternierung von Ring-Stickstoffatomen mit verschiedenen Reagenzien (I₂, Br₂, Cl₂, CrO₃, Pikrinsäure, HgCl₂). wurden Poly(2-vinylpyridin)komplexe hergestellt. Unter Anwendung der modifizierten Freeman and Carroll Methode wurde das thermische Verhalten dieser Polymerkomplexe untersucht, wie z.B. E und Reaktionsordnung der Zersetzungsreaktion. Allgemein wurde festgestellt, daß die Anwesenheit einer Gruppe am Stickstoff im Polymer die Aktivierungsenergie senkt und seine thermische Stabilität verringert.

     

Synthesis,characterization, and investigation of structure‐thermal cycloimidization relationship of novel poly(amide amic acid)s to poly(amide imide)s by thermogravimetric analysis

Novel diamic acids (DAAs) and poly(amide amic acid)s (PAAs) were prepared and their thermal cycloimidization to the corresponding imide form was investigated by thermogravimetric analysis under isothermal conditions at four different temperatures, that is, at 175, 200, 225, and 260 °C for 75 min. A general equation, 18NW/R_MW, where, the numerical 18 corresponds to the molecular weight of water, N is the number of water molecules, which would be eliminated per repeat unit of the PAA upon cycloimidization, W is the weight of PAA taken for TGA, and R is the molecular weight of the repeat unit of PAA, has been derived for the calculation of theoretical amount of weight loss of PAA upon complete cycloimidization. The degree of cycloimidization (DCI%) of PAAs to poly(amide imide)s (PAI) has been calculated from their isothermal TGA curves. The variation in DCI on temperature, time, and the structures of diamine and acid chloride, especially, with respect to meta‐ and para‐linkages and the presence of electron withdrawing groups has been discussed. Cycloimidization occurs at faster rate in the initial stages of about 20 min, curing and then proceeds in a gradual manner and reaches almost a plateau within an hour. The DCI was more at higher temperatures, and the final values were 22?60% at 175 °C, 34?78% at 200 °C, 50?96% at 225 °C, and 85?99% at 260 °C after 75 min of heating, depending on the nature of diamine and acid chloride in the PAA. The DCI of PAAs with meta‐linkages in either of diamine or diacid chloride was somewhat lower than those having para‐linkages. The DCI of PAAs containing electron withdrawing group like sulfone in the diamine is somewhat higher compared with those of others. The final DCI (%) values obtained from FT‐IR spectra and isothermal TGA curves were very close to each other. Further, the thermal and thermooxidative stabilities of the PAIs were discussed. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2937–2947, 2007     

Novel organosoluble aromatic polyimides bearing pendant methoxy‐substituted triphenylamine moieties: Synthesis,electrochromic, and gas separation properties

Four series of polyimides I – VI with pendent triphenylamine (TPA) units having inherent viscosities of 0.44–0.88 dL/g were prepared from four diamines with two commercially available tetracarboxylic dianhydrides via a conventional two‐step procedure that included a ring‐opening polyaddition to give polyamic acids, followed by chemical cyclodehydration. These polymers were amorphous and could afford flexible films. All the polyimides had useful levels of thermal stability associated with high softening temperatures (279–300 °C), 10% weight‐loss temperatures in excess of 505 °C, and char yields at 800 °C in nitrogen higher than 58%. The hole‐transporting and electrochromic properties were examined by electrochemical and spectroelectrochemical methods. Cyclic voltammograms of the polyimide films cast onto an indium‐tin oxide (ITO)‐coated glass substrate exhibited a or two reversible oxidation couples at 0.65–0.78 and 1.00–1.08 V versus Ag/AgCl in acetonitrile solution. The polymer films revealed electrochromic characteristics with a color change from neutral pale yellowish to blue doped form at applied potentials ranging from 0.00 to 1.20 V. The CO₂ permeability coefficients (P) and permeability selectivity (P/P) for these polyimide membranes were in the range of 4.73–16.82 barrer and 9.49–51.13, respectively. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7937–7949, 2008     

甲基取代的聚芳醚酮酮酰亚胺树脂的合成与性能

N,N′-(4,4′-二苯甲烷)-二偏苯三甲酰亚胺酰氯(DIDC-M)与4,4′-二(2-甲基-苯氧基)三苯二酮(o-Me-DPOTPDK) 进行低温溶液共缩聚,制备了甲基侧基取代的聚芳醚酮酮酰亚胺(o-Me-PEKKI)聚合物.用FT-IR,1H-NMR,DSC,TG 和WAXD对聚合物的结构和性能进行了表征.研究表明:聚合物为非晶态结构;具有较高的玻璃化转变温度(Tg:241 ℃)和较好的耐热性能(Td:487 ℃);能溶解于间甲酚、NMP、氯仿、四氯乙烷等有机溶剂中.     

A multifunctional poly(aryl ether) with oligoaniline and fluorene pendants: Synthesis,electrochromic performance,and tunable fluorescent properties

A novel multifunctional poly(aryl ether) with both pendant oligoaniline and fluorene groups (PAE‐p‐OF) was synthesized by nucleophilic polycondensation and characterized by ¹H NMR, Fourier‐transform infrared spectra, and gel permeation chromatography. The polymer showed excellent solubility in common organic solvents and good thermal stability. Electrochemical and photophysical properties were also investigated using cyclic voltammetry, UV–vis, and fluorescence spectroscopies. The obtained PAE‐p‐OF exhibits satisfactory electrochromic properties with high contrast value, acceptable coloration efficiency, and moderate switching times. Moreover, the fluorescence intensity of PAE‐p‐OF was modulated by controlling oxidation degree of oligoaniline moiety, due to the energy migration occurring between oligoaniline and fluorene groups. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Hyperbranched aromatic poly(ether imide)s: Synthesis,characterization, and modification

The synthesis and characterization of hyperbranched aromatic poly(ether imide)s are described. An AB₂ monomer, which contained a pair of phenolic groups and an aryl fluoro moiety activated toward displacement by the attached imide heterocyclic ring, was prepared. The nucleophilic substitution of the fluoride with the phenolate groups led to the formation of an ether linkage and, subsequently, to the hyperbranched poly(ether imide), which contained terminal phenolic groups. A similar one‐step polymerization involving a monomer that contained silyl‐protected phenols yielded a hyperbranched poly(ether imide) with terminal silylated phenols. The degree of branching of these hyperbranched polymers was approximately 55%, as determined by a combination of model compound studies and ¹H NMR integration experiments. End‐capping reactions of the terminal phenolic groups were readily accomplished with a variety of acid chlorides and acid anhydrides. The nature of the chain‐end groups significantly influenced physical properties, such as the glass‐transition temperature and the solubility of the hyperbranched poly(ether imide)s. As the length of the acyl chain of the terminal ester groups increased, the glass‐transition temperature value for the polymer decreased, and the solubility of the polymer in polar solvents was reduced, becoming more soluble in nonpolar solvents. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2536–2546, 2001     

Novel thermooxidatively stable poly(ether-imide-benzoxazole) and poly(ester-imide-benzoxazole)

4-Hydroxy-5-nitrophthalimides were produced via nucleophilic aromatic substitution (NAS) of 4,5-dichloro phthalimide substituents by potassium nitrite. The use of a N-phenyl-phthalimide having a protected 4′-hydroxyl group allows concurrent deprotection and nitro reduction to amine to give the 4-hydroxy-5-amino-N-(4′-hydroxyphenyl) phthalimide. This key intermediate is the precursor to a poly (ether-imide-benzoxazole), and is the condensable monomer for a poly (ester-imide-benzoxazole). Benzoxazole monomer formation via condensation with p-fluorobenzoyl chloride afforded 2-(4′-fluorophenyl)-5,6,-N-[4′(-hydroxyphenyl) imide]-benzoxazole, which was polymerized under NAS conditions to produce a poly(ether-imide-benzoxazole) having an endothermic transition at 454°C with weight retention of 90% at 500°C in both air and nitrogen. Solution polycondensation of the 4-hydroxy-5-amino-N-(4′-hydroxyphenyl) phthalimide monomer with isophthaloyl chloride afforded a poly(ester-amide-imide) which was isolated and thermally cyclodehydrated in the solid state under vacuum to give a poly(ester-imide-benzoxazole) having 95% weight retention at 500°C in both air and nitrogen, with no detectable DSC transitions up to 500°C. © 1994 John Wiley & Sons, Inc.     

Synthesis and characterization of poly(aryl ether imide)s containing electroactive perylene diimide and naphthalene diimide units

The synthesis and polymerization of two new electroactive bisphenols derived from 3,4,9,10‐perylenetetracarboxylic dianhydride and 1,4,5,8‐naphthalenetetracarboxylic dianhydride with 2‐(4‐aminophenyl)‐2‐(4‐hydroxyphenyl)propane, respectively, are described. Copolymerization using the two new bisphenols and 4,4′‐isopropylidenediphenol with bis(4‐fluorophenyl)sulfone and 4,4′‐difluorobenzophenone, afforded a series of soluble electrochromic poly(aryl ether imide)s with glass‐transition temperatures ranging from 160 to 315 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3467–3475, 2000