含氨基聚芳醚酮/磺化聚芳醚酮砜中高温质子交换复合膜的制备与性能研究

以自制的高磺化度磺化聚芳醚酮砜(SPAEKS)和含有氨基的聚芳醚酮(Am-PAEK)为原料,通过共溶剂涂膜法制备了不同重量比例的Am-PAEK/SPAEKS复合膜.通过高温(160℃)处理使氨基和磺酸基团在复合膜内形成交联,制得交联型复合膜.复合膜的热性能、尺寸稳定性、阻醇性能有所提高,而且交联型复合膜中的Am-PAEK/SPAEKS-C-3质子传导率在120℃时达到了0.0892 S/cm,高于在相同测试条件下SPAEKS膜的0.0654 S/cm和Nafion膜的0.062 S/cm,而其甲醇渗透系数在25℃时达到0.14×10-6cm2/s,低于SPAEKS膜的0.85×10-6cm2/s和Nafion膜的2×10-6cm2/s.实验结果表明,Am-PAEK/SPAEKS交联型复合膜有望在中高温质子交换膜燃料电池中得到应用.     

Investigation of sulfonated poly(ether ether ketone sulfone)/heteropolyacid composite membranes for high temperature fuel cell applications

The sulfonated poly(ether ether ketone sulfone) (SPEEKS)/heteropolyacid (HPA) composite membranes with different HPA content in SPEEKS copolymers matrix with different degree of sulfonation (DS) were investigated for high temperature proton exchange membrane fuel cells. Composite membranes were characterized by Fourier transfer infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). FTIR band shifts suggested that the sulfonic acid groups on the copolymer backbone strongly interact with HPA particles. SEM pictures showed that the HPA particles were uniformly distributed throughout the SPEEKS membranes matrix and particle sizes decreased with the increment of copolymers' DS. The holes were not found in SPEEKS‐4/HPA30 (consisting of 70% SPEEKS copolymers with DS = 0.8 and 30% HPA) composite membrane after composite membranes were treated with boiling water for 24 h. Thermal stabilities of the composite membranes were better than those of pure sulfonated copolymers membranes. Although the composite membranes possessed lower water uptake, it exhibited higher proton conductivity for SPEEKS‐4/HPA30 especially at high temperature (above 100 °C). Its proton conductivity linearly increased from 0.068 S/cm at 25 °C to 0.095 S/cm at 120 °C, which was higher than 0.06 S/cm of Nafion 117. In contrast, proton conductivity of pure SPEEKS‐4 membrane only increased from 0.062 S/cm at 25 °C to 0.078 S/cm at 80 °C. At 120 °C, proton conductivity decreased to poor 0.073 S/cm. The result indicated that composite membranes exhibited high proton conductivity at high temperature. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1967–1978, 2006     

Proton conducting composite membranes from polysulfone and heteropolyacid for fuel cell applications

The viability of using composite membranes of heteropolyacid (HPA)/polysulfone (PSF), HPA/sulfonated polysulfone (SPSF) for use in proton exchange membrane fuel cells (PEMFC) was investigated. PSF and its sulfonated polymer, SPSF was solution‐blended with phosphotungstic acid, a commercially available HPA. Fourier transform infrared (FTIR) spectroscopy of the HPA–40/SPSF composite exhibited band shifts showing a possibility of intermolecular hydrogen bonding interaction between the HPA additive and the sulfonated polymer. The composite membranes exhibited improved mechanical strength and low water uptake. The conductivity of the composite membrane, HPA–40/SPSF, consisting of 40 wt % HPA and 60 wt % SPSF [with a degree of Sulfonation (DS) of 40%] exhibited a conductivity 0.089 S/cm at room temperature that linearly increased upto 0.14 S/cm at 120 °C, whereas the widely used commercial membrane Nafion 117, exhibited a room temperature conductivity of 0.1 S/cm that increased to only 0.12 S/cm at 120 °C. In contrast, the composite of HPA–40/PSF exhibited a proton conductivity of 0.02 S/cm at room temperature that increased only to 0.07 S/cm at a temperature of 100 °C. The incorporation of HPA into SPSF not only rendered the membranes suitable for elevated temperature operation of PEMFC but also provides an inexpensive alternative compared to Nafion. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1538–1547, 2005     

质子交换膜对钒氧化还原液流电池性能的影响

采用溶液接枝聚合法制备了一种新型的质子交换膜PVDF-g-PSSA, 测定了PVDF-g-PSSA膜、Nafion 117 膜和PE01均相膜的离子交换能力和电导率, 并分别研究了以这3种膜为隔膜的钒电池的电化学性能. 实验结果表明, PVDF-g-PSSA膜具有优良的质子电导率和离子交换能力, 室温下其离子交换能力和质子电导率分别为1.13 mmol/g和3.22×10-2 S/cm, 在不同的充放电电流密度下, 以PVDF-g-PSSA膜为隔膜的钒电池的库仑效率和能量效率明显高于Nafion 117膜和PE01均相膜为隔膜的钒电池; PVDF-g-PSSA膜阻钒离子的渗透性能与PE01均相膜基本一致, 都明显优于Nafion 117膜的阻钒离子渗透能力.     

磺化聚芳醚砜/磺化聚酰亚胺复合质子交换膜的制备与性能研究

利用溶液浇铸法制备了一系列双磺化型磺化聚芳醚砜/磺化聚酰亚胺(SPAES/SPI)复合质子交换膜.扫描电子显微镜(SEM)结果显示复合膜不存在明显的相分离,表明二者具有很好的相容性.由于SPI的引入,复合膜在甲醇中稳定性较纯SPAES具有大幅的提高,比Nafion112低得多的甲醇吸收率表明了这些复合膜具有比后者更低的甲醇透过率.复合膜显示了与单组分膜相类似的高温分解稳定性,磺酸基团的分解温度达到了290℃以上.复合膜显示出远高于纯SPAES膜的尺寸稳定性能,在130℃高温中200h处理后,所有的复合膜均保持了高的机械性能,而此时纯SPAES膜已经溶解于水中.而且由于两种磺化聚合物间的复合,复合膜维持了较高的IEC水平,显示了较高的质子导电率,在80%相对湿度时的质子导电率与Nafion112相近,而在水中的质子导电率均高于Nafion112.     

In situ polymerization: A novel route for thermally stable proton-conductive membranes

In this paper, a new solvent-free route for preparing proton-conductive membranes is proposed. Flexible and fiber-supported polymer electrolyte membranes, as potential proton exchange membranes, were readily obtained by in situ polymerization of a homogenous solution that consisted of bromomethylated poly(2,6-dimethyl-1,4-phenylene oxide) (BPPO, polymer)–monomer mixtures of styrene (ST) and divinylbenzene (DVB), which was pre-cast onto SEFAR PETEX fibers. Factors such as the components of the casting solution and the sulfonation time, were fully investigated. The membrane structure and components were confirmed by FTIR-ATR spectra and SEM-EDXA images, and the thermal stability was examined via TGA and DrTGA. The membrane exhibited a proton conductivity of about 0.07 S/cm at 100% humidity and at room temperature, which is close to that of Nafion 117 at identical conditions (around 0.08 S/cm), whereas its thickness (about 120 μm) was less than that of Nafion 117. The tensile strength and the elongation at the break of the membrane were 31.2 MPa and 71%, respectively, which are several times higher than those of Nafion (about 6.16 MPa tensile strength and 36% elongation ratio). The dimensional change ratio of the membrane between the wet and dry states was below 3%, which is much lower than that of Nafion 117. The membrane showed a high thermal stability up to 400 °C. The method can be applied to other compatible systems of (aromatic) polymers and (aromatic) monomers.     

SPES/PWA/SiO_2复合质子交换膜的性能

以磺化聚醚砜(SPES)为基体,以不同比例的SiO2溶胶与磷钨酸(PWA)为掺杂物,制备了一种有望用于直接甲醇燃料电池(DMFC)的新型SPES/PWA/SiO2有机-无机复合膜,并经热失重分析(TGA)、差示扫描量热仪(DSC)、扫描电镜(SEM)-X射线能谱分析(EDX)等对膜的结构和性能进行了表征,探讨了复合膜用作质子交换膜的可能性.结果表明:复合膜较纯SPES膜具有更高的热稳定性、玻璃化转变温度和吸水率;虽然在室温和电池操作温度(80℃)下,复合膜的拉伸强度均低于纯SPES膜,但即使当SiO2含量高达20%(w)时,复合膜的拉伸强度仍高于Nafion112膜的;SEM图片显示SiO2和PWA在膜中分布均匀,这将有利于连续质子传输通道的形成.对于SiO2含量为15%(w),PWA含量为6%(w)的复合膜,其室温质子传导率达到了0.034S·cm-1,与Nafion112膜的相当,但其甲醇渗透率明显降低,仅为商用Nafion112膜的七分之一左右,这表明该复合膜在直接甲醇燃料电池中具有良好的应用前景.     

Preparation of Nafion/sulfonated poly(phenylsilsesquioxane) nanocomposite as high temperature proton exchange membranes

Nafion/sulfonated poly(phenylmethyl silsesquioxane) (sPPSQ) composite membranes are fabricated using homogeneous dispersive mixing and a solvent casting method for direct dimethyl ether fuel cell (DDMEFC) applications operated above 100 °C. The inorganic conducting filler, sPPSQ significantly affects the characteristics in the nanocomposite membranes by functionalization with an organic sulfonic acid to PPSQ. Moreover, sPPSQ content plays an important role in membrane properties such as microstructure, proton conductivity, fuel crossover, and single cell performance test. With increasing sPPSQ content in the nanocomposite membrane, the proton conductivity increased and fuel crossover decreased. However, in a higher temperature range above 110 °C, Nafion/sPPSQ 5 wt.% composite membrane has the highest proton conductivity. Also, the DME permeability for the composite membrane with higher sPPSQ content increased sharply. The excessive sPPSQ content caused a large aggregation of inorganic fillers, leading to the deterioration of membrane properties. In this study, the optimal sPPSQ content for maximizing the DDMEFC performance was 5 wt.%. Our nanocomposite membranes demonstrated proton conductivities as high as 1.57 × 10⁻¹ S/cm at 120 °C, which is higher than that of Nafion. The cell performances were compared to Nafion/sPPSQ composite membrane with Nafion 115, and the composite membrane with sPPSQ yielded better cell performance than Nafion 115 at temperatures ranging from 100 to 120 °C and at pressures from 1 to 2 bar.     

磺化聚芳醚酮砜/聚芳醚砜噁二唑复合型质子交换膜的制备与性能

为了降低质子交换膜(PEM)的甲醇渗透系数和改善PEM在中高温(80~120 ℃)时的质子传导率, 以自制的磺化度(SD)为100%的磺化聚芳醚酮砜(SPAEKS)与聚芳醚砜噁二唑(PAESO)为原料, 采用溶液共混法制备了SPAEKS/PAESO复合膜, 并用傅里叶变换红外光谱(FTIR)和热重分析(TGA)对其进行了表征. 结果表明, 该复合膜具有较好的化学稳定性和热稳定性. 扫描电子显微镜(SEM)照片显示, 复合膜具有较好的致密结构, 其甲醇渗透系数为3.9×10^-7~6.6×10^-7 cm²/s, 低于SPAEKS的8.7×10^-7 cm²/s. 在100 ℃时复合膜的质子传导率达到0.074 S/cm, 高于SPAEKS膜的0.066 S/cm.     

Sulfonated poly(phenylene oxide) membranes as promising materials for new proton exchange membranes

Poly(phenylene oxide) (PPO) was sulfonated to different ion exchange capacities (IECs) using chlorosulfonic acid as the sulfonating agent. Tough, ductile films were successfully cast from sulfonated PPO (SPPO) solutions in N‐methyl‐2‐pyrrolidone or N,N‐dimethylformamide. The obtained membranes had good thermal stability revealed by thermogravimetric analysis (TGA). Compared with an unsulfonated PPO membrane, the hydrophilicity and water uptake of the SPPO membranes were enhanced, as shown by reduced contact angles with water. The tensile test indicated that the SPPO membranes with IEC ranging from 0.77 to 2.63 meq/g were tough and strong at ambient conditions and still maintained adequate mechanical strength after immersion in water at room temperature for 24 hr. The results of wide‐angle X‐ray diffraction (WAXD) showed amorphous structures for PPO and SPPO while the peak intensity decreased after sulfonation. The proton conductivity of these SPPO membranes was measured as 1.16 × 10^?2 S/cm at ambient temperature, which is comparable to that of Nafion 112 at similar conditions and in the range needed for high‐performance fuel cell proton exchange membranes. Copyright © 2006 John Wiley & Sons, Ltd.     

SPEEK-zirconium hydrogen phosphate composite membranes with low methanol permeability prepared by electro-migration and in situ precipitation

Sulfonated poly(ether ether ketone) (SPK)-zirconium hydrogen phosphate (ZrP) composite membranes were prepared by electro-driven migration of Zr(4+) and simultaneous in situ precipitation of ZrP using phosphoric acid under different electrical gradient, in order to avoid loss in its mechanical stability. Degree of sulfonation was estimated from (1)H NMR and ion-exchange capacity study that was found to be 61% and 57%, respectively. In this method Zr(4+) and HPO(4)(2-) were allowed to diffuse within the pores/channels of the preformed SPK membrane under given electrical gradient and ZrP was precipitated within the membrane matrix. ZrP loading density was measured as a function of applied electrical gradient for a definite reaction time (4 h) and electrolytic environment. Membranes with varied ZrP loading densities were characterized for their thermal and mechanical stabilities, physicochemical and electrochemical properties using thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), scanning electron microscopy (SEM), water content, proton conductivity and methanol permeability. No loss in thermal and mechanical stability of membranes was observed due to incorporation of inorganic component (ZrP) in the membrane matrix. Although the composite membranes exhibited low proton conductivity in comparison to SPK membrane at room temperature, but the presence of the inorganic particles led to an improvement in high temperature conductivity. Selectivity parameter of these composite membranes was estimated at two temperatures namely 30 and 70 degrees C, in latter case it was found significantly higher than that for Nafion membrane (0.79 x 10(5) S s cm(-3)) under similar experimental conditions.     

全钒液流电池用磺化聚醚醚酮/锂皂石质子膜的结构及性能

通过溶液流延法制备了磺化聚醚醚酮/锂皂石(SPEEK/Lap)复合膜, 对其物理化学性质、 机械性能、 化学稳定性及单电池性能进行了测试. 在SPEEK基质中引入的Lap有效改善了复合膜的质子传导率、 溶胀率和机械性能. 当Lap添加量(质量分数)从0.2%增到1.5%时, 复合膜的质子传导率随之增加(19.9~23.6 mS/cm). SPEEK/Lap-0.2复合膜的自放电时间为57.2 h, 是Nafion 117膜的2.4倍和纯SPEEK膜的1.5倍. 在80 mA/cm ²电流密度下, SPEEK/Lap-0.2复合膜的电压效率(VE, 86.5%)和能量效率(EE, 84.0%)明显高于Nafion 117膜(VE: 83.8%, EE: 80.7%)和纯SPEEK膜(VE: 81.4%, EE: 78.9%). 同时, SPEEK/Lap-0.2复合膜经100次充放电循环测试后具有良好的循环稳定性和结构稳定性.     

Tuned polymer electrolyte membranes based on aromatic polyethers for fuel cell applications

Poly(arylene ether sulfone)-based ionomers containing sulfofluorenyl groups have been synthesized for applications to polymer electrolyte membrane fuel cells (PEMFCs). In order to achieve high proton conductivity and chemical, mechanical, and dimensional stability, the molecular structure of the ionomers has been optimized. Tough, flexible, and transparent membranes were obtained from a series of modified ionomers containing methyl groups with the ion-exchange capacity (IEC) ranging from 1.32 to 3.26 meq/g. Isopropylidene tetramethylbiphenylene moieties were more effective than the methyl-substituted fluorenyl groups in giving a high-IEC ionomer membrane with substantial stability to hydrolysis and oxidation. Dimensional stability was significantly improved for the methyl-substituted ionomer membranes compared to that of the non-methylated ones. This new ionomer membrane showed comparable proton conductivity to that of the perfluorinated ionomer membrane (Nafion 112) under a wide range of conditions (80-120 degrees C and 20-93% relative humidity (RH)). The highest proton conductivity of 0.3 S/cm was obtained at 80 degrees C and 93% RH. Although there is a decline of proton conductivity with time, after 10 000 h the proton conductivities were still at acceptable levels for fuel cell operation. The membranes retained their strength, flexibility, and high molecular weight after 10 000 h. Microscopic analyses revealed well-connected ionic clusters for the high-IEC membrane. A fuel cell operated using the polyether ionomer membrane showed better performance than that of Nafion at a low humidity of 20% RH and high temperature of 90 degrees C. Unlike the other hydrocarbon ionomers, the present membrane showed a lower resistance than expected from its conductivity, indicating superior water-holding capability at high temperature and low humidity.     

含氨基磺化聚芳醚酮砜质子交换膜的制备与性能

通过四元缩聚的方法合成了带有氨基的磺化度可控的磺化聚芳醚酮砜共聚物(Am-SPAEKS). 采用红外光谱和核磁共振谱表征了Am-SPAEKS共聚物的结构. 该共聚物膜具有较好的热性能、尺寸稳定性、较高的质子传导率和阻醇能力. 在80℃时Am-SPAEKS-1膜的质子传导率达到0.0894 S/cm, 而其甲醇渗透系数在25℃时为0.24×10^-6 cm²/s, 低于相同温度下SPAEKS膜(0.87×10^-6 cm²/s)和Nafion膜(2×10^-6 cm²/s). 结果表明, Am-SPAEKS膜能够满足质子交换膜燃料电池(PEMFC)的使用要求.     

A novel composite Nafion membrane for direct alcohol fuel cells

Trifluoromethanesulfonic acid or triflate acid, chemical formula CF₃SO₃H, is regarded as one of the strongest acids and resembles Nafion^® in structure. Erbium triflate, a lanthanum salt of triflate, is thermally stable. This paper reports data on the formation of membranes by the fixation of erbium triflate salts (ErTfO) into the Nafion structure. Five different loadings of ErTfO were used to fabricate ErTfO/Nafion composite membranes and these were characterized, extensively for possible use in direct alcohol fuel cells. The membranes were characterized using XRD, TGA, FTIR, and for mechanical strength, water uptake, ion exchange capacity, alcohol uptake, swelling, proton conductivity, alcohol permeability and oxygen stability. The ErTfO/Nafion composite membranes reduced alcohol permeability by 77–80%. The proton conductivity of 3% ErTfO/Nafion composite membranes was 38% higher than that of a pure cast Nafion membrane. The oxygen stability of the ErTfO/Nafion composite membranes was higher than pure cast Nafion. However, the mechanical strength of 7% and 9% ErTfO/Nafion was lower than that of pure cast Nafion. The composite membrane was chemically stable and has potential for use in direct alcohol fuel cells.     

DMFCs用磺化聚醚醚酮/功能化二氧化硅复合质子交换膜

在磺化度(DS)为55.1%的磺化聚醚醚酮(SPEEK)中掺杂功能化二氧化硅(吸湿性SiO2溶胶及带有磺酸基团的二氧化硅(SiOx-S)粒子)制备SPEEK/SiO2和SPEEK/SiOx-S复合质子交换膜.SiO2和SiOx-S的掺杂能有效提高复合膜的抗溶胀、阻醇性能及高温低湿情况下的电导率.纯SPEEK膜在80℃溶胀为52.6%,而SiO2和SiOx-S掺杂量为15%的复合膜在此温度下分别仅有26.2%和27.3%的溶胀.在室温至80℃范围内,SPEEK/SiO2(20 wt%)和SPEEK/SiOx-S(20 wt%)复合膜的甲醇透过系数比Nafion115膜小近2个数量级.在120℃、相对湿度(RH)为40%情况下,SPEEK纯膜的电导率仅为2.6×10-4S.cm-1,SPEEK/SiO2(20 wt%)复合膜约为2.0×10-3S.cm-1,而SPEEK/SiOx-S(20 wt%)复合膜高达1.0×10-2S.cm-1,与Nafion115相当.SPEEK/SiO2(20 wt%)和SPEEK/SiOx-S(20 wt%)2种复合膜的尺寸稳定性较高,膜电极无催化剂与膜分离现象,其DMFCs单电池性能好于SPEEK膜.     

Enhanced proton conductivity of polymer electrolyte membrane doped with titanate nanotubes

Nafion-titanate nanotubes composite membranes were prepared through a casting process. With the addition of 5 wt.%, the nanotubes were homogenously distributed in Nafion solution. The formed composite membrane showed a comparable mechanical strength to Nafion membrane. The proton conductivity of the composite membrane without external humidification is higher than that of the Nafion membrane, reaching 0.034 Scm^?1 and 0.01 Scm^?1 at 100 °C and 120 °C, respectively. The improved proton conductivity was attributed to the great water retention ability of the doped nanotubes.     

含甲基磺化杂萘联苯聚醚砜酮质子交换膜材料的合成与性能

以4-(3,5-二甲基-4-羟基苯基)2,3-二氮杂萘-1-酮,3,3′-二磺酸钠-4,4′-二氟苯甲酮和4,4′-二氯二苯砜为原料,利用亲核缩聚反应,通过改变磺化单体的含量,制备出一系列不同磺化度的杂萘联苯聚醚砜酮(SPPESK-DM).采用FTIR、1H-NMR表征了聚合物的结构,热失重分析仪研究了聚合物的耐热稳定性,以N-甲基-2-吡咯烷酮为溶剂采用溶液浇铸法成膜研究该系列聚合物膜的性能.结果表明,SPPESK-DM磺酸基的热分解温度在260℃以上,主链分解温度在410℃以上;膜的吸水率、溶胀率、离子交换容量和质子传导率均随着磺化度的增大而增大,磺化度为1.0的SPPESK-DM50的质子传导率达到1.08×10-2S/cm(85℃),且甲醇渗透系数为2.06×10-7cm2/s,低于Nafion117膜的甲醇渗透系数(2×10-6cm2/s).此系列膜的耐氧化性比较优异,可望用于质子交换膜燃料电池中.     

New proton conducting hybrid membranes for HT-PEMFC systems based on polysiloxanes and SO3H-functionalized mesoporous Si-MCM-41 particles

For increased efficiency of high-temperature polymer electrolyte membrane fuel cells (HT-PEMFC), new types of membranes have to be developed. This approach has been realized by preparing hybrid membranes containing SO₃H-functionalized mesoporous Si-MCM-41 as hydrophilic inorganic modifier in a polysiloxane matrix exhibiting sulfonic acid groups and basic heterocyclic groups like benzimidazole. The proton conductivity of sulfonated particles was modelled on the atomic scale in order to understand the influence of the density of sulfonic acid groups and of the presence of water molecules. The different hybrid membranes are characterized concerning their thermal stability, water uptake, and proton conductivity. Whereas the proton conductivity of well-established, but expensive and at >120 °C not long-time stable Nafion membranes continuously decreases with increasing temperature, the polysiloxane membranes, which suffer from a low-proton conductivity at around 100 °C, recover at about 120 °C due to intrinsic proton transport. At 180 °C the pure polysiloxane shows a proton conductivity which is only one order of magnitude lower than that of Nafion. Moreover, if the polysiloxane membrane contains additionally 10 wt.% of an SO₃H-modified Si-MCM-41, the proton conductivity of such hybrid membrane at temperatures >180 °C and low relative humidity <10% is higher than that of Nafion membranes by a factor of 10.     

Synthesis and properties of novel sulfonated (co)polyimides bearing sulfonated aromatic pendant groups for PEFC applications

Novel sulfonated diamines bearing aromatic pendant groups, namely, 3,5‐diamino‐3′‐sulfo‐4′‐(4‐sulfophenoxy) benzophenone (DASSPB) and 3,5‐diamino‐3′‐sulfo‐4′‐(2,4‐disulfophenoxy) benzophenone (DASDSPB), were successfully synthesized. Novel side‐chain‐type sulfonated (co)polyimides (SPIs) were synthesized from these two diamines, 1,4,5,8‐naphthalene tetracarboxylic dianhydride (NTDA) and nonsulfonated diamines such as 4,4′‐bis(3‐aminophenoxy) phenyl sulfone (BAPPS). Tough and transparent membranes of SPIs with ion exchange capacity of 1.5–2.9 meq g^?1 were prepared. They showed good solubility and high thermal stability up to 300 °C. They showed isotropic membrane swelling in water, which was different from the main‐chain‐type and sulfoalkoxy‐based side‐chain‐type SPIs. The relative humidity (RH) and temperature dependence of proton conductivity were examined. At low RH, the novel SPI membranes showed much higher conductivity than the sulfoalkoxy‐based SPIs. They showed comparable or even higher proton conductivity than Nafion 112 in water at 60 °C (>0.10 S cm^?1). The membrane of NTDA‐DASDSPB/BAPPS (1/1)‐s displayed reasonably high proton conductivities of 0.05 and 0.30 S cm^?1 at 50 and 100% RH, respectively, at 120 °C. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2862–2872, 2006