Stability of silanols and grafted alkylsilane monolayers on plasma-activated mica surfaces

We investigated the effect of physical and chemical modifications of mica surfaces induced by water vapor-based plasma treatments on the stability of silanols and grafted alkylsilane monolayers. The plasma-activated substrates were characterized using XPS, TOF-SIMS, and contact angle measurements. They revealed a large surface coverage of silanol groups (Si-OH) and a loss of aluminum atoms compared to freshly cleaved mica surfaces. The stability of plasma-induced silanol groups was investigated by contact angle measurements using ethylene glycol as a probe liquid. The Si-OH surface coverage decreased rapidly under vacuum or thermal treatment to give rise to hydrophobic dehydrated surfaces. The stability of end-grafted monofunctionalized n-alkylsilanes was investigated in different solvents and at different pH using water contact angle measurements. The degrafting of alkylsilanes from the activated mica was promoted in acidic aqueous solutions. This detachment was associated with the hydrolysis of covalent bonds between the alkylsilanes and the mica surface. The monolayer stability was enhanced by increasing the length of the alkyl chains that probably act as a hydrophobic protective layer against hydrolysis reactions. Stable alkylsilane monolayers in water with pH greater than 5.5 were obtained on mica surfaces activated at low plasma pressure. We attributed this stability to the loss of surface Al atoms induced by the plasma treatment.     

Chemical modification of silica surfaces

The formation of phenylaerosil via silica hydride in the gas phase and the subsequent introduction of nitro and amino groups in solution has been followed using IR and UV spectroscopy. The direct reaction of aminophenyltriethoxysilane (APhS) with the silica surface has also been investigated.     

Adhesion of single polyelectrolyte molecules on silica, mica, and bitumen surfaces

In a recent study (Energy Fuels 2005, 19, 936), a partially hydrolyzed polyacrylamide (HPAM) was used as a process aid to recover bitumen from oil sand ores. It was found that HPAM addition at the bitumen extraction step not only improved bitumen recovery but also enhanced fine solids settling in the tailings stream. To understand the role of HPAM, single-molecule force spectroscopy was employed for the first time to measure the desorption/adhesion forces of single HPAM molecules on silica, mica, and bitumen surfaces using an atomic force microscope (AFM). Silicon wafers with an oxidized surface layer and newly cleaved mica were used, respectively, to represent sand grains and clays in oil sands. The force measurements were carried out in deionized water and in commercial plant process water under equilibrium conditions. The desorption/adhesion forces of HPAM obtained on mica, silica, and bitumen surfaces were approximately 200, 40, and 80 pN in deionized water and approximately 100, 50, and 40 pN in the plant process water, respectively. The measured adhesion forces together with the zeta potential values of these surfaces indicate that the polymer would preferentially adsorb onto clay surfaces rather than onto bitumen surfaces. It is the selective adsorption of HPAM that benefits both bitumen recovery and tailings settling when the polymer was added directly to the bitumen extraction process at an appropriate dosage.     

Wetting behavior of lightly sulfonated polystyrene ionomers on silica surfaces

The wetting/dewetting behavior of thin films of lightly sulfonated low molecular weight polystyrene (SPS) ionomers spin-coated onto silica surfaces were studied using atomic force microscopy (AFM), contact angle measurements, and electron microscopy. The effects of the sulfonation level, the choice of the cation, the solvent used to spin-coat the films, and the molecular weight of the ionomer were investigated. Small angle X-ray scattering was used to determine the bulk microstructure of the films. The addition of the sulfonate groups suppressed the dewetting behavior of the PS above its glass transition temperature, e.g. no dewetting occurred even after 240 h of annealing at 120 degrees C. Increasing the sulfonation level led to more homogeneous and smoother surfaces. The choice of the cation used affected the wetting properties, but not in a predictable manner. When tetrahydrofuran (THF) or a THF/methanol mixed solvent was used for spin-casting, a submicron-textured surface morphology was produced, which may be a consequence of spinodal decomposition of the film surface during casting. Upon annealing for long times, the particles coalesced into a coherent, nonwetted film.     

Nanoscale repulsive forces between mica and silica surfaces in aqueous solutions

Nanoscale repulsive forces between mineral surfaces in aqueous solutions were measured for the asymmetric mica-silica system. The force measured with an atomic force microscope (AFM) has universal character in the short range, less than ～1 nm or about 3-4 water molecules, independent of solution conditions, that is, electrolyte ion (Na, Ca, Al), concentration (10(-6)-10(-2)M), and pH (3.9-8.2). Notably, the force is essentially the same as for the glass-silica system. Single force curves for a mica-silica system in a 10(-4)M aqueous NaCl solution at pH ～ 5.1 show oscillations with a period of about 0.25 nm, roughly the diameter of a water molecule, a consequence of a layer-by-layer dehydration of the surfaces when pushed together. This result provides additional support to the idea that nanoscale repulsive forces between mineral surfaces in aqueous solutions arise from a surface-induced water effect; the water between two mineral plates that are pushed together becomes structured and increasingly anchored to the surface of the plates by the creation of a hydrogen-bonding network that prevents dehydration of the surfaces.     

Adsorption of polyelectrolyte modified graphene to silica surfaces: monolayers and multilayers

Exfoliated graphene particles stabilised by the cationic polyelectrolyte polyethyleneimine (PEI) were used in conjunction with an anionic polyelectrolyte, poly(acrylic acid), to construct multilayers using the layer-by-layer technique on a silica substrate. In the first adsorption step, the surface excess of the cationic graphene was dependent on the overall charge on the nanoparticle which in turn can be tuned through modifying solution pH as PEI has weakly ionisable charged amine groups. The adsorbed amount onto the silica surface increased as the solution pH increased. Subsequently, a layer of PAA was adsorbed on top of the cationic graphene through electrostatic interaction. The multilayer could be assembled through this alternate deposition, with the influence of solution conditions investigated. The pH of the adsorbing solutions was the chief determinant of the overall adsorbed amounts, with more mass added at the elevated pH of 9 in comparison with pH 4. Atomic force microscopy confirmed that the graphene particles were adsorbed to the silica interface and that the surface coverage of the disc-like nanoparticles was complete after the deposition of five graphene-polyelectrolyte bi-layers. Furthermore, the graphene nanoparticles themselves could be modified through the consecutive addition of the oppositely charged polymers. A multilayered assembly of negatively charged graphene sheets modified with a bi-layer of PEI and PAA was also deposited on a silica surface with adsorbed PEI.     

Hematite nanoparticle monolayers on mica electrokinetic characteristics

Electrokinetic properties of α-Fe(2)O(3) (hematite) nanoparticle monolayers on mica were thoroughly characterized using the streaming potential method. Hematite suspensions were obtained by acidic hydrolysis of ferric chloride. The average size of particles (hydrodynamic diameter), determined by dynamic light scattering (DLS) and AFM, was 22nm (pH=5.5, I=10(-2)M). The hematite monolayers on mica were produced under diffusion-controlled transport from the suspensions of various bulk concentration. The monolayer coverage, quantitatively determined by AFM and SEM, was regulated within broad limits by adjusting the nanoparticle deposition time. This allowed one to uniquely express zeta potential of hematite monolayers, determined by the streaming potential measurements, in terms of the particle coverage. Such dependencies, obtained for various pH, were successfully interpreted in terms of the three-dimensional electrokinetic model. A universal calibrating graph was produced enabling one to determine hematite monolayer coverage from the measured value of the streaming potential. The influence of the ionic strength, varied between 10(-4) and 10(-2)M, on the zeta potential of hematite monolayers was also studied. Additionally, the stability of monolayers (desorption kinetics) was determined under in situ conditions using the streaming potential method. Our experimental data prove that it is feasible to produce uniform and stable hematite particle monolayers of well-controlled coverage. Such monolayers may find practical applications as universal substrates for protein immobilization (biosensors) and in electrocatalytic applications.     

Interaction of water with self-assembled monolayers of alkylsilanes on mica

The interaction of water with self-assembled alkylsilane monolayers on mica substrates has been studied using an atomic force microscope operated in contact, noncontact, and electrical polarization modes. Complete monolayer films were found to be effective in blocking water adsorption. On partially covered surfaces water was found to produce large changes in the conductivity and surface potential of the exposed mica regions. It was also found that water could penetrate films near defects and at island edges.     

Hematite nanoparticle monolayers on mica preparation by controlled self-assembly

In this research, a simple, green and effective strategy was developed to produce long-term stable oil in water emulsion from soy protein and soy polysaccharide. Soy protein and soy polysaccharide formed dispersible complexes at pH around 3.25 aqueous solution through electrostatic and hydrophobic interactions. A high pressure homogenization produced the protein/polysaccharide complex emulsion having a droplet size about 250 nm. A heat treatment of the emulsion resulted in the protein denaturation, forming irreversible oil-water interfacial films composed of soy protein/soy polysaccharide complexes. The droplets of the emulsion were characterized by dynamic light scattering, ζ-potential, transmission electron microscopy, polysaccharide digestion via pectinase, and confocal laser scanning microscopy observation via dual fluorescence probes. As a result of the polysaccharide being fixed on the droplet surface, the emulsions exhibited long-term stability in the media containing pH values of 2-8 and 0.2 mol/L NaCl. The stable soy protein/soy polysaccharide complex emulsion is a suitable food-grade delivery system in which lipophilic bioactive compounds can be encapsulated.     

Robust self-assembled octadecylphosphonic acid monolayers on a mica substrate

As determined by scratch tests, self-assembled monolayers (SAMs) of octadecylphosphonic acid (OPA) on a muscovite mica substrate were found to be mechanically robust and to serve as a lubricant to protect the underlying mica substrate. For comparison purposes, three polymer films were subjected to scratch tests under the same conditions. The scratch tests were conducted using a diamond-tipped stylus, and the resultant scratches were examined using atomic force microscopy. The excellent mechanical strength of OPA SAMs is supported by analysis with time-of-flight secondary ion mass spectrometry, which suggests that the headgroup of the OPA is strongly bonded to the substrate atoms. The molecular lubrication provided by OPA SAMs suggests that the interaction between the headgroup and the substrate is sufficiently strong to endure significant shear force and that the hydrocarbon chains are able to dissipate shear energy.     

ToF-SIMS investigation of octadecylphosphonic acid monolayers on a mica substrate

In this paper, time-of-flight secondary ion mass spectrometry (ToF-SIMS) under static conditions was used to investigate self-assembled monolayers (SAMs) of octadecylphosphonic acid (OPA) formed on freshly cleaved muscovite mica substrates. The coverage of OPA on mica ranged from 20 to 100%, with a film thickness of 1.7+/-0.2 nm, which was determined by atomic force microscopy (AFM) imaging. The relative intensity of the specific secondary ion species associated with the OPA and with the exposed mica substrate exhibited good correlation with surface coverage. An excellent correlation was also observed (R2=0.98) between the relative SIMS [OPA-H]- intensity and the surface carbon concentration (OPA C 1s, in atomic %) from XPS at the prescribed surface coverage. The observation of positive and negative OPA molecular attachment of secondary ions involving the substrate species is discussed in terms of the chemical affinity of the OPA phosphonate headgroup for the cleaved mica surface as well as the sampling depth. In addition, the OPA molecular attachment species formed with the potassium ions on the cleaved mica substrate dominated the positive secondary ion mass spectrum in the high-mass range. A temperature-dependent, ToF-SIMS study employing in situ heating of a 100% coverage OPA monolayer revealed that the molecules begin to diffuse above approximately 80 degrees C, resulting in a decrease in the relative secondary ion yield of the OPA-specific secondary ions. This observation is hypothesized to be due to a decrease in the effective coverage of the substrate by the OPA molecules, which in turn could be due to the formation of multilayers upon heating in an effort to minimize the energy of the system. The interesting behavior of the novel OPA dimer species as a function of temperature is also reported. It was observed that the relative intensity of OPA and the mica-specific secondary ion peak intensities to that of Si (mica substrate) provides an effective means to estimate the change in coverage at elevated temperatures.     

Length-controlled rodlike self-assemblies in binary mixed langmuir-blodgett monolayers on mica

In this paper, atomic force microscopy (AFM) has been used to investigate the morphology of monolayers of the amphiphilic rod-coil diblock molecule (EO7OPV) containing oligo(phenylene vinylene) dimer (OPV) and poly(ethylene oxide) (PEO) as well as the morphology of mixed monolayers of EO7OPV and palmitic acid (PA) deposited onto mica by the Langmuir-Blodgett technique. At surface pressures higher than 3 mN/m, EO7OPV forms regular-shaped aggregates with a monomolecular layer structure, where the hydrophilic PEO blocks are adsorbed onto the mica substrate and the hydrophobic OPV blocks form an ordered crystalline OPV layer on the top of the PEO layer through the strong pi-pi stacking interaction. In the mixed LB monolayers of EO7OPV and PA, the phase separation occurs. At a certain mixed ratio, EO7OPV molecules form rodlike domains with regular shape and uniform size at surface pressures higher than 3 mN/m. With the increase of the molar fraction of PA, the rodlike domains consisting of EO7OPV are elongated. The length of the rodlike domains can be tuned easily in a large range by altering the molar ratio of EO7OPV and PA. In addition, the rodlike domains are oriented to specific directions, corresponding to the directions of the potassium ion array on the mica surface having 6-fold symmetry. We demonstrate the possible formation mechanism and the elongation origin of rodlike domains in mixed LB monolayers and propose the two-step formation process of oriented rodlike domains deposited onto the mica substrate.     

Photoresponsive monolayers on water and solid surfaces

Organic photochromic units and molecules can be regarded as light-driven nano molecular machines. Once such molecules are aligned at a surface, the supramolecular organization provides an efficient macroscopic mechanical response in a collective way. Amphiphilic polymers having an azobenzene (Az) side chain are the favorable materials for observation of such effects since they show marked photomechanical response with essentially full reversibility. An in situ Brewster angle microscopic observation showed marked morphological and rheological photoinduced changes in the molecular films. Moreover, we have newly found that the identical photosensitive molecular film transferred on to a solid mica surface shows large morphological changes under highly humid conditions as proven by atomic force microscopy (AFM). It is supposed that the molecular film is driven in the same mechanism both on water and water-adsorbed mica surfaces. These microscopic observations provide new insights of the photomechanical response in photochromic monolayers.     

Mechanical and frictional properties of nanoparticle monolayers grafted on functionalized mica substrates

Normal and lateral forces between two opposing monolayers of grafted polymer nanoparticles (NPs) were measured using the Surface Forces Apparatus in a humid atmosphere. The NPs made of N, N-diethylacrylamide and 2-hydroxyethyl methacrylate have a hydrodynamic diameter of ca. 660 nm at 25 degrees C. The effect of surface roughness was studied by creating surface asperities using different NP grafting densities ranging from 0.41 to 2.63 NPs/mum (2). An increase in the NPs grafting density gave rise to an increase in surface roughness and to a deformation of the nanoparticles caused by the lateral pressure between neighboring particles. An elastoplastic behavior of the nanoparticles was observed for large grafting densities, while a purely elastic behavior was observed for small grafting densities. The lateral forces measured between two opposing NP monolayers sliding past each other followed Amontons' law for all grafting densities. The friction coefficient between the surfaces appeared to increase significantly with an increase in surface roughness, which was inherent to an increase in the elastoplastic behavior of the NP monolayers.     

Conducting ferrocene monolayers on nonconducting surfaces

The redox activity of a ferrocenyl monolayer grafted on an n-type Si111 substrate was investigated by scanning electrochemical microscopy (SECM) in conditions where the substrate plays the role of an insulator. This approach permits the differentiation between the different possible electron-transfer and mass-transport pathways occurring at the interface. As an exciting result, the thin ferrocenyl monolayer behaves like a purely conducting material, highlighting very fast electron communication between immobilized ferrocenyl headgroups in a 2D-like charge-transport mechanism.     

Phosphonate self-assembled monolayers on aluminum surfaces

Substrates of aluminum (Al) deposited by physical vapor deposition onto Si substrates and then chemically reacted with perfluorodecylphosphonic acid (PFDPAlSi), decylphosphonic acid (DPAlSi), and octadecylphosphonic acid (ODPAlSi) were studied by x-ray photoelectron spectroscopy (XPS), contact angle measurements, atomic force microscopy (AFM), and friction force microscopy, a derivative of AFM, to characterize their surface chemical composition, roughness, and micro-/nanotribological properties. XPS analysis confirmed the presence of perfluorinated and nonperfluorinated alkylphosphonate molecules on the PFDPAlSi, DPAlSi, and ODPAlSi. The sessile drop static contact angle of pure water on PFDPAlSi was typically more than 130 degrees and on DPAlSi and ODPAlSi typically more than 125 degrees indicating that all phosphonic acid reacted AlSi samples were very hydrophobic. The surface roughness for PFDPAlSi, DPAlSi, ODPAlSi, and bare AlSi was approximately 35 nm as determined by AFM. The surface energy for PFDPAlSi was determined to be approximately 11 mNm by the Zisman plot method compared to 21 and 20 mNm for DPAlSi and ODPAlSi, respectively. Tribology involves the measure of lateral forces due to friction and adhesion between two surfaces. Friction, adhesion, and wear play important roles in the performance of micro-/nanoelectromechanical systems. PFDPAlSi gave the lowest adhesion and coefficient of friction values while bare AlSi gave the highest. The adhesion and coefficient of friction values for DPAlSi and ODPAlSi were comparable.     

Epitaxially guided assembly of collagen layers on mica surfaces

Ordered assembly of collagen molecules on flat substrates has potential for various applications and serves as a model system for studying the assembly process. While previous studies demonstrated self-assembly of collagen on muscovite mica into highly ordered layers, the mechanism by which different conditions affect the resulting morphology remains to be elucidated. Using atomic force microscopy, we follow the assembly of collagen on muscovite mica at a concentration lower than the critical fibrillogenesis concentration in bulk. Initially, individual collagen molecules adsorb to mica and subsequently nucleate into fibrils possessing the 67 nm D-periodic bands. Emergence of fibrils aligned in parallel despite large interfibril distances agrees with an alignment mechanism guided by the underlying mica. The epitaxial growth was further confirmed by the formation of novel triangular networks of collagen fibrils on phlogopite mica, whose surface lattice is known to have a hexagonal symmetry, whereas the more widely used muscovite does not. Comparing collagen assembly on the two types of mica at different potassium concentrations revealed that potassium binds to the negatively charged mica surface and neutralizes it, thereby reducing the binding affinity of collagen and enhancing surface diffusion. These results suggest that collagen assembly on mica follows the surface adsorption, diffusion, nucleation, and growth pathway, where the growth direction is determined at the nucleation step. Comparison with other molecules that assemble similarly on mica supports generality of the proposed assembly mechanism, the knowledge of which will be useful for controlling the resulting surface morphologies.     

Negative adsorption and liquid chromatography of polystyrene on silica

The main factors that determine negative adsorption of polymers have been considered. These are the preferred (positive) adsorption of the solvent molecules and the sieve effect during the interaction of macromolecules with a porous adsorbent. Modification of the silica surface, solvent polarity, and the size of the macromoleculer coils of polystyrene favor the negative sorption of polystyrene by porous silica and size-exclusion chromatography separation of macromolecules. The relations between the partition coefficient of a substance between the bulk and the adsorption phases and the excess values of retention, the capacity factor, and the adsorption coefficient (the Henry constant) are analyzed.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 9, pp. 2204–2208, September, 1996.     

Freezing of fluids confined between mica surfaces

Using grand ensemble simulations, we show that octamethyl-cyclo-tetra-siloxane (OMCTS) confined between two mica surfaces can form a variety of frozen phases which undergo solid-solid transitions as a function of the separation between the surfaces. For atomically smooth mica surfaces, the following sequence of transitions 1[triangle up] --> 1[triangle up]b --> 2B --> 2 square --> 2[triangle up] are observed in the one- and two-layered regimes, where n[triangle up], n[square], and nB denote triangular, square, and buckled phases, respectively, with the prefix n denoting the number of confined layers. The presence of potassium on mica is seen to have a strong influence on the degree of order induced in the fluid. The sequence of solid-solid transitions that occurs with the smooth mica surface is no longer observed. When equilibrated with a state point near the liquid-solid transition, a counterintuitive freezing scenario is observed in the presence of potassium. Potassium disrupts in-plane ordering in the fluid in contact with the mica surface, and freezing is observed only in the inner confined layers. The largest mica separations at which frozen phases were observed ranged from separations that could accommodate six to seven fluid layers. The extent of freezing and the square-to-triangular lattice transition was found to be sensitive to the presence of potassium as well as the thermodynamic conditions of the bulk fluid. The implications of our results on interpretation of surface force experiments as well as the generic phase behavior of confined soft spheres is discussed.