Nanowear studies in chemically heterogeneous responsive polymeric brushes by surface force microscopy

In this study, we present nanowear studies using surface force microscopy (SFM), on nanoscopic thin films of reversibly switchable binary polymer brushes [polystyrene (PS) + poly(2-vinylpyridine) (P2VP)] and respective monobrushes [polystyrene and poly(2-vinylpyridine)] synthesized via “grafting to” method. The aim was to tune the wear in nanothin polymer brush surfaces. Therefore, the effect of conformational switching of PS + P2VP brush on treatment with selective solvents for PS and P2VP chains on the wear process was investigated. Wear process on thick spin-coated films of PS and P2VP was also investigated for comparison. Nanowear experiments were performed using SFM tip by repeating scans over the surface to follow the wear process closely. The wear process on different surfaces was explained on the basis of molecular entanglement as well as adhesion and friction on the sample surface. For spin-coated PS film as well as PS and PS + P2VP brush surfaces (treated with toluene) with molecular entanglements at surface, wear mechanism involved formation of ripples. However, in case of spin-coated P2VP films as well as P2VP and PS + P2VP brush surfaces (treated with ethanol) with no molecular entanglements at surface, wear occurred via removal of polymer chains and their accumulation at the rim. For PS + P2VP surface treated with acidic water, wear mechanism was complex and inhomogeneous ripple formation was followed by formation of heaps of polymeric material in the center of scanned area. The extent of wear as measured either by root mean square roughness of the surface or spacing between the ripples, increased with the number of scans for all the surfaces. Our study shows that wear mode of polymer brush surfaces is different for different polymers and can be controlled/tuned by the use of binary polymer brushes.     

Adhesion between chemically heterogeneous switchable polymeric brushes and an elastomeric adhesive

We investigated the adhesive properties of binary heterogeneous polymer brushes made from end-functionalized polystyrene (PS) and poly(2-vinylpyridine) (P2VP) chains. The molecular organization of the mixed brush could be varied reversibly by exposure to selective solvents for PS (toluene) and for P2VP (acidic water). This exposure results in reversible switching of adhesive and wetting properties. The manner in which the adhesion switching occurs can be tuned by the composition of mixed brushes. However, the outer surface composition could be enriched more effectively in PS after the toluene treatment than in P2VP after the acidic water treatment. As a result, the mixed brush compositions that showed the largest difference in properties between an exposure to toluene and an exposure to water were the P2VP-rich compositions. Adhesive properties, tested against a soft hydrophobic pressure-sensitive adhesive (PSA) using a probe test, always showed smaller differences between solvent treatments than wetting properties with water, suggesting a much higher sensitivity of the hydrophobic/hydrophilic brushes to polar molecules than to nonpolar molecules.     

两亲性杂侧链聚合物刷的合成及其乳化功能

报道了一种随机高密度接枝亲水、疏水聚合物侧链的刷形两亲性聚合物.首先,结合可逆加成-断裂链转移(RAFT)聚合和后修饰方法,得到含叠氮侧基的聚甲基丙烯酸缩水甘油酯(PGMA-N3)作为主链;再分别合成端炔基聚苯乙烯(PS)和端炔基聚环氧乙烷(PEO),然后通过铜催化的叠氮-炔环加成反应,将疏水性PS和亲水性PEO同时高效的接到PGMA主链上,制得两亲性杂侧链的聚合物刷.由凝胶渗透色谱(SEC)分析得知,在主链叠氮基团与两侧链总炔基的摩尔投料比为1∶1的条件下,PS和PEO的接枝效率很高,都大于90%.通过调节主链长度和2种侧链的投料比,获得不同组成的聚合物刷.通过等质量的甲苯/水混合体系,考察两亲性聚合物刷的乳化能力,发现主链聚合度为100,PS∶PEO比例为70∶30的聚合物刷表现出最佳的乳化性能.     

Transmission electron microscopy study of solvent-induced phase morphologies of environmentally responsive mixed homopolymer brushes on silica particles

We report in this work a transmission electron microscopy study of phase morphologies of environmentally responsive mixed poly( t-butyl acrylate) (P tBA)/polystyrene (PS) brushes and mixed poly(acrylic acid) (PAA)/PS brushes on 180 nm silica particles after treatments with nonselective good solvents and selective solvents, respectively. Mixed P tBA/PS brushes were grown from Y-initiator-functionalized silica particles by sequential atom transfer radical polymerization and nitroxide-mediated radical polymerization. Mixed PAA/PS brushes were prepared from mixed P tBA/PS brushes by removal of the t-butyl groups. For mixed P tBA/PS brushes with P tBA M n of 24.2 kDa and PS M n of 23.0 kDa and the corresponding mixed PAA/PS brushes, random worm-like, nearly bicontinuous nanostructures were formed from lateral microphase separation when the particles were cast from nonselective good solvents (chloroform for mixed P tBA/PS brushes and N, N-dimethylformamide for mixed PAA/PS brushes). The feature sizes were on the order of polymer chain root-mean-square end-to-end distances ( approximately 10 nm). In contrast, mixed P tBA/PS brushes with lower molecular weights (P tBA M n = 10.4 kDa and PS M n = 11.9 kDa) did not strongly phase separate after being cast from chloroform. After the solvents in the particle dispersions were gradually changed to selective solvents ( n-octane for mixed P tBA/PS brushes and H 2O for mixed PAA/PS brushes), isolated microdomains with an average size of 14-19 nm were formed as one grafted polymer collapsed and associated to form isolated microdomains, which were shielded by another grafted polymer yielding surface-tethered micellar structures. These results confirmed the theoretical predictions of the formation of "rippled" nanostructures and surface micellar structures of mixed homopolymer brushes induced by nonselective and selective solvents, respectively.     

Cellular responses to patterned poly(acrylic acid) brushes

We use patterned poly(acrylic acid) (PAA) polymer brushes to explore the effects of surface chemistry and topography on cell-surface interactions. Most past studies of surface topography effects on cell adhesion have focused on patterned feature sizes that are larger than the dimensions of a cell, and PAA brushes have been characterized as cell repellent. Here we report cell adhesion studies for RBL mast cells incubated on PAA brush surfaces patterned with a variety of different feature sizes. We find that when patterned at subcellular dimensions on silicon surfaces, PAA brushes that are 30 or 15 nm thick facilitate cell adhesion. This appears to be mediated by fibronectin, which is secreted by the cells, adsorbing to the brushes and then engaging cell-surface integrins. The result is detectable accumulation of plasma membrane within the brushes, and this involves cytoskeletal remodeling at the cell-surface interface. By decreasing brush thickness, we find that PAA can be 'tuned' to promote cell adhesion with down-modulated membrane accumulation. We exemplify the utility of patterned PAA brush arrays for spatially controlling the activation of cells by modifying brushes with ligands that specifically engage IgE bound to high-affinity receptors on mast cells.     

Nanowear on polymer films of different architecture

In this paper, we describe atomic force microscope (AFM) friction experiments on different polymers. The aim was to analyze the influence of the physical architecture of the polymer on the degree and mode of wear and on the wear mode. Experiments were carried out with (1) linear polystyrene (PS) and cycloolefinic copolymers of ethylene and norbornene, which are stabilized by entanglements, (2) mechanically stretched PS, (3) polyisoprene-b-polystyrene diblock copolymers, with varying composition, (4) brush polymers consisting of a poly(methyl methacrylate) (PMMA) backbone and PS side chains, (5) PMMA and PS brushes grafted from a silicon wafer, (6) plasma-polymerized PS, and (7) chemically cross-linked polycarbonate. For linear polymers, wear depends critically on the orientation of the chains with respect to the scan direction. With increasing cross-link density, wear was reduced and ripple formation was suppressed. The cross-linking density was the dominating material parameter characterizing wear.     

Amphiphilic copolymer grafted "smart surface" enhanced by surface roughness

Polystyrene-poly(acrylic acid) (PS-PAA) block copolymers polymerized by atom transfer radical polymerization were covalently grafted to both smooth and microtextured surfaces. These amphiphilic copolymers were utilized to create smart surfaces, which can be responsive to external stimuli, e.g., pH values or organic solvent. Atom force microscopy, field emission scanning electron microscopy, and contact angle measurements were employed to investigate the physiochemical features of the copolymer brushes. It was found that the wettability of surfaces depended on both the PS/PAA molar ratio and external solvent properties. Hydrophilic surfaces were obtained after treatment with basic solution, as well as a polar solvent, such as ethanol. With treatment with acidic solution or toluene, the surface could be reversibly turned relatively hydrophobic, probably due to the rearrangement or reorganization of polymer chains. Moreover, rougher surfaces, which were microtextured by ZnO nanorods, were incorporated into this adaptive system to enhance the tunable range of wettability.     

Wetting transition on hydrophobic surfaces covered by polyelectrolyte brushes

We study the wetting by water of complex "hydrophobic-hydrophilic" surfaces made of a hydrophobic substrate covered by a hydrophilic polymer brush. Polystyrene (PS) substrates covered with polystyrene- block-poly(acrylic acid) PS- b-PAA diblock copolymer layers were fabricated by Langmuir-Schaefer depositions and analyzed by atomic force microscopy (AFM) and ellipsometry. On bare PS substrate, we measured advancing angles theta A = 93 +/- 1 degrees and receding angles theta R = 81 +/- 1 degrees . On PS covered with poorly anchored PS- b-PAA layers, we observed large contact angle hysteresis, theta A approximately 90 degrees and theta R approximately 0 degrees , that we attributed to nanometric scale dewetting of the PS- b-PAA layers. On well-anchored PS- b-PAA layers that form homogeneous PAA brushes, a wetting transition from partial to total wetting occurs versus the amount deposited: both theta A and theta R decrease close to zero. A model is proposed, based on the Young-Dupre equation, that takes into account the interfacial pressure of the brush Pi, which was determined experimentally, and the free energy of hydration of the polyelectrolyte monomers Delta G PAA (hyd), which is the only fitting parameter. With Delta G PAA (hyd) approximately -1300 J/mol, the model renders the wetting transition for all samples and explains why the wetting transition depends mainly on the average thickness of the brush and weakly on the length of PAA chains.     

Complex pH- and temperature-sensitive swelling behavior of mixed polymer brushes

The ability of a mixed polymer brush consisting of poly(N-isopropyl acrylamide) (PNIPAAM) and poly(acrylic acid) (PAA) to modify physicochemical interfacial properties is presented. The answer of the binary brush toward changes of environmental conditions like temperature, salt concentration, and pH value was investigated by in situ spectroscopic VIS-ellipsometry as well as AFM and contact angle mesurements in the dry state and compared with the behavior of the corresponding homopolymer brushes. A coupled swelling of PNIPAAm and PAA could be found, leading to a complex pH-, salt-, and temperature-sensitive swelling behavior of these mixed brushes, also depending on the composition of the brush. The complex interaction of the two polymers resulted in new properties of the mixed system. Although the temperature sensitivity of the mixed system was decreased compared with that of the corresponding PNIPAAM brushes, the sensitivity toward pH and salt concentration was amplified compared with that of pure PAA brushes. Additionally it is shown that in spite of the decreased temperature sensitivity of the mixed brush, a temperature-dependent adsorption of human serum albumin was observed whereas an increased adsorption affinity was found that is not predictable from the adsorption affinity of the corresponding homopolymer brushes. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1606–1615, 2010     

PS/PMMA mixed polymer brushes on the surface of clay layers: Preparation and application in polymer blends

Polystyrene (PS) and poly(methyl methacrylate) (PMMA) mixed polymer brushes on the surface of clay layers were prepared by using in situ free radical polymerization. Free radical initiator molecules with two quaternary ammonium groups at both ends were intercalated into the interlayer spacing of clay layers. The amount of polymer brushes grafted on the surface of clay layers can be controlled by controlling the polymerization time. Thermogravimetric analysis, X‐ray diffraction, and high‐resolution transmission electron microscope results indicated successful preparation of the mixed polymer brushes on the surface of clay layers. The kinetics of the grafting of the monomers was also studied. The mixed polymer brushes on the surface of clay layers were used as compatibilizers in blends of PS and PMMA. In the blends, the intercalated clay particles tend to locate at the interface of two phases reducing the interfacial tension. In the meanwhile, PMMA homopolymer chains tend to intercalate into clay layers. The driving force for the intercalation is the compatibility between homo‐PMMA chains and PMMA brushes on the surface of clay layers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5329–5338, 2007     

A combinatorial approach to study solvent-induced self-assembly of mixed poly(methyl methacrylate)/polystyrene brushes on planar silica substrates: effect of relative grafting density

This article reports the study of the effect of relative grafting densities of two polymer chains on solvent-induced self-assembly of mixed poly(methyl methacrylate) (PMMA)/polystyrene (PS) brushes through a combinatorial approach. Gradient-mixed PMMA/PS brushes were synthesized from a gradient-mixed initiator-terminated monolayer by combining atom transfer radical polymerization (ATRP) and nitroxide mediated radical polymerization (NMRP) in a two-step process. The gradient-mixed initiator-terminated monolayer was fabricated by first formation of a gradient in density of an ATRP initiator through vapor diffusion followed by backfilling of an NMRP-initiator-terminated trichlorosilane. After treatment of a gradient-mixed brush whose PS Mn was slightly lower than that of PMMA with glacial acetic acid, a selective solvent for PMMA, relatively ordered nanodomains were observed in the region where the ratio of PS to PMMA grafting density (number of polymer chains/nm2) was in the range from 0.67 to 2.17 and the overall grafting density was approximately 0.85 polymer chains/nm2. Contact angle hysteresis were high (> or =40 degrees ) in this region and XPS studies confirmed that the PMMA chains were enriched at the outermost layer. The nanodomains are speculated to be of a micellar structure with PS chains forming the core shielded by PMMA chains.     

Control of surface properties using fluorinated polymer brushes produced by surface-initiated controlled radical polymerization

Surface-grafted styrene-based homopolymer and diblock copolymer brushes bearing semifluorinated alkyl side groups were synthesized by nitroxide-mediated controlled radical polymerization on planar silicon oxide surfaces. The polymer brushes were characterized by X-ray photoelectron spectroscopy (XPS), near-edge X-ray absorption fine structure (NEXAFS), and time-dependent water contact angle measurements. Angle-resolved XPS studies and water contact angle measurements showed that, in the case of the diblock copolymer brushes, the second block to be added was always exposed at the polymer-air interface regardless of its surface energy. Values of z*/Rg were estimated based on the radius of gyration, Rg, of the grafted homopolymer or block copolymer chains for the grafted brushes and thickness of the brush, z*. The fact that z*/Rg > 1 suggests that all these brushes are stretched. These results support the idea that after grafting the first block onto the surface the nitroxide-end capped polymer chains were able to polymerize the second block in a "living" fashion and the stretched brush so formed was dense enough that the outermost block in all cases completely covers the surface. NEXAFS analysis showed a relationship between the surface orientation of the fluorinated side chains and brush thickness with thicker brushes having more oriented side chains. Time-dependent water contact angle measurements revealed that the orientation of the side chains of the brush improved the surface stability toward reconstruction upon prolonged exposure to water.     

Memory of surface patterns in mixed polymer brushes: simulation and experiment

The correlation between the morphology of mixed polymer brushes and fluctuations of the grafting points is investigated by single-chain-in-mean-field simulations and experiments. The local topography of two types of mixed polystyrene-polymethylmethacrylate (PS-PMMA) brushes that differ in their modes of attachment has been studied during repeated microphase separation into laterally structured and homogeneous morphologies upon changing solvents. In the first type of brush (conventional), each of the surface-attached initiator groups starts the growth of either a PS or a PMMA chain in a random fashion. In the second case (Y-shaped mixed brushes), two chains of different types are attached to the same anchor group on the substrate. Whereas in the first case statistical fluctuations of the chemical composition occur on a local scale, such composition fluctuations are strongly suppressed in the latter case. The microphase-separated morphology is similar in both cases, but Y-shaped brushes exhibit a significantly weaker domain memory than do conventional PS-PMMA mixed brushes. The results of the experiment are compared with simulations, and a simple phenomenological argument and qualitative agreement are found. The observations demonstrate that small fluctuations in the grafting points are amplified by the microphase separation and nucleate the location of the domains in the mixed brush.     

Solvent-induced self-assembly of mixed poly(methyl methacrylate)/polystyrene brushes on planar silica substrates: molecular weight effect

The effect of molecular weight on the solvent-induced self-assembly of mixed poly(methyl methacrylate) (PMMA)/polystyrene (PS) brushes on silicon wafers was studied. For a series of mixed brushes with a fixed PMMA M(n) and systematically changed PS M(n), a transition in water advancing contact angle (theta(a)) from 74 degrees, the value for a flat PMMA surface, to 91 degrees, the value for a flat PS film, was observed with increasing PS M(n) after treatment with CHCl(3). Atomic force microscopy studies showed smooth surfaces for all samples. While no significant changes in surface morphologies were observed after treatment with cyclohexane, a selective solvent for PS, contact angle and XPS studies indicated that the mixed brushes with a PS M(n) slightly smaller than that of PMMA underwent self-reorganization, exhibiting a different theta(a). Intriguing surface morphologies composed of relatively ordered nanoscale domains were found from mixed brushes with PS M(n) slightly smaller than or similar to that of PMMA after treatment with acetic acid, a selective solvent for PMMA. The nanodomains are speculated to be of a micellar structure, with PS chains forming a core shielded by PMMA chains.     

Synthesis of Spherical Polyelectrolyte Brushes by Thermo‐controlled Emulsion Polymerization

A novel method of thermo‐controlled emulsion polymerization has been employed to synthesize spherical polyelectrolyte brushes that consist of a solid polystyrene core and a poly (acrylic acid) (PAA) shell covalently attached on the core surface densely by one end. The growth of brushes from the core surface was monitored by dynamic light scattering (DLS). The particle size of PS core latex showed a narrow size distribution when observed by scanning electron microscopy (SEM). The brush size changed significantly upon changing pH value and ionic strength, and displayed similar behavior to brushes prepared by photo‐emulsion polymerization. The grafting density of the PAA brush, which was determined by cutting off the PAA chains using alkali hydrolysis, confirmed the formation of PAA brushes.

     

Mixed polymer brushes by sequential polymer addition: anchoring layer effect

Smart surfaces can be described as surfaces that have the ability to respond in a controllable fashion to specific environmental stimuli. A heterogeneous (mixed) polymer brush (HPB) can provide a synthetic route to designing smart polymer surfaces. In this research we study HPB comprised of end-grafted polystyrene (PS) and poly(2-vinyl pyridine) (P2VP). The synthesis of the HPB involves the use of an "intermolecular glue" acting as a binding/anchoring interlayer between the polymer brush and the substrate, a silicon wafer. We compare anchoring layers of epoxysilane (GPS), which forms a self-assembled monolayer with epoxy functionality, to poly(glycidyl methacrylate) (PGMA), which forms a macromolecular monolayer with epoxy functionality. The PS and P2VP were deposited onto the wafers in a sequential fashion to chemically graft PS in a first step and subsequently graft P2VP. Rinsing the HPB in selective solvents and observing the change in water contact angle as a function of the HPB composition studied the switching nature of the HPB. Scanning probe microscopy was used to probe the topography and phase imagery of the HPB. The nature of the anchoring layer significantly affected the wettability and morphology of the mixed brushes.     

Interfacial friction and adhesion of polymer brushes

A bead-probe lateral force microscopy (LFM) technique is used to characterize the interfacial friction and adhesion properties of polymer brushes. Our measurements attempt to relate the physical structure and chemical characteristics of the brush to their properties as thin-film, tethered lubricants. Brushes are synthesized at several chain lengths and surface coverages from polymer chains of polydimethylsiloxane (PDMS), polystyrene (PS), and a poly(propylene glycol)-poly(ethylene glycol) block copolymer (PPG/PEG). At high surface coverage, PDMS brushes manifest friction coefficients (COFs) that are among the lowest recorded for a dry lubricant film (μ ≈ 0.0024) and close to 1 order of magnitude lower than the COF of a bare silicon surface. Brushes synthesized from higher molar mass chains exhibit higher friction forces than those created using lower molar mass polymers. Increased grafting density of chains in the brush significantly reduces the COF by creating a uniform surface of stretched chains with a decreased surface viscosity. Brushes with lower surface tension and interfacial shear stresses manifest the lowest COF. In particular, PDMS chains exhibit COFs lower than PS by a factor of 3.7 and lower than PPG/PEG by a factor of 4.7. A scaling analysis conducted on the surface coverage (σ) in relation to the fraction (ε) of the friction force developing from adhesion predicts a universal relation ε ~ σ(4/3), which is supported by our experimental data.     

In-situ investigation of the adsorption of globular model proteins on stimuli-responsive binary polyelectrolyte brushes

Binary brushes constituted from two incompatible polymers can be used in the form of ultrathin polymeric layers as a versatile tool for surface engineering to tune physicochemical surface characteristics such as wettability, surface charge, chemical composition, and morphology and furthermore to create responsive surface properties. Mixed brushes of oppositely charged weak polyelectrolytes represent a special case of responding surfaces that are sensitive to changes in the pH value of the aqueous environment and therefore represent interesting tools for biosurface engineering. The polyelectrolyte brushes used for this study were composed of two oppositely charged polyelelctrolytes poly(2-vinylpyridine) (P2VP) and poly(acrylic acid) (PAA). The in-situ properties and surface characteristics such as as surface charge, surface tension, and extent of swelling of these brush layers are functions of the pH value of the surrounding aqueous solution. To test the behavior of the mixed polylelctrolyte brushes in contact with biosystems, protein adsorption experiments with globular model proteins were performed at different pH values and salt concentrations (confinement of counterions) of the buffer solutions. The influence of the pH value, buffer salt concentration, and isoelectric points (IEP) of the brush and protein on the adsorbed amount and the interfacial tension during protein adsorption as well as the protein adsorption mechanism postulated in reference to recently developed theories of protein adsorption on polyelectrolyte brushes is discussed. In the salted regime, protein adsorption was found to be similar to the often-described adsorption at hydrophobic surfaces. However, in the osmotic regime the balance of electrostatic repulsion and a strong entropic driving force, "counterion release", was found to be the main influence on protein adsorption.     

BSA adsorption on bimodal PEO brushes

BSA adsorption onto bimodal PEO brushes at a solid surface was measured using optical reflectometry. Bimodal brushes consist of long (N=770) and short (N=48) PEO chains and were prepared on PS surfaces, applying mixtures of PS(29)-PEO(48) and PS(37)-PEO(770) block copolymers and using the Langmuir-Blodgett technique. Pi-A isotherms of (mixtures of) the block copolymers were measured to establish the brush regime. The isotherms of PS(29)-PEO(48) show hysteresis between compression and expansion cycles, indicating aggregation of the PS(29)-PEO(48) upon compression. Mixtures of PS(29)-PEO(48) and PS(37)-PEO(770) demonstrate a similar hysteresis effect, which eventually vanishes when the ratio of PS(37)-PEO(770) to PS(29)-PEO(48) is increased. The adsorption of BSA was determined at brushes for which the grafting density of the long PEO chains was varied, while the total grafting density was kept constant. BSA adsorption onto monomodal PEO(48) and PEO(770) brushes was determined for comparison. The BSA adsorption behavior of the bimodal brushes is similar to the adsorption of BSA at PEO(770) monomodal brushes. The maximum of BSA adsorption at low grafting density of PEO(770) can be explained by ternary adsorption, implying an attraction between BSA and PEO. The contribution of primary adsorption to the total adsorbed amount is negligible.     

Solvent dependent friction force response of polystyrene brushes prepared by surface initiated polymerization

Polystyrene (PS) brushes were prepared on oxide passivated silicon by the surface initiated polymerization (SIP) technique. From an AIBN-type free radical initiator, which was silanized and immobilized on silicon wafers, styrene brushes were directly polymerized and grafted from the surface. The formation of the initiator monolayer and, subsequently, the polymer brush on the surface were monitored by X-ray photoelectron spectroscopy (XPS) and ellipsometry. Friction force measurements were performed by atomic force microscopy (AFM), using a 5 microm SiO2 colloidal sphere tip and under systematically varied solvent environments (nonpolar to polar), to demonstrate the dependence of brush lubricity on solvation. The relative uptake of solvents in the PS brush was determined by quartz crystal microbalance (QCM), and it correlates well with friction data. It is surmised that, in poor solvent environments, the polymer brush exists in a collapsed conformation, giving rise to the higher observed friction response.