Investigation of cutting of engineering ceramics with Q-switched pulse CO2 laser

In this paper, the cutting of Si₃N₄ engineering ceramics with Q-switched pulse CO₂ laser is studied. Considering the influence of the cut front shape on the absorption of the laser beam, a simplified 2D mathematic model is developed based on a pulsed laser vaporization cut process. This model is based on the conservation of energy. The experimental results show that it would realize crack-free cutting by using high-speed and multi-pass feed cutting process.     

Estimating cutting front temperature difference in disk and CO2 laser beam fusion cutting

A three-dimensional, semi-stationary, simplified thermal numerical model was developed. The average cutting front temperature difference in disk and CO₂ laser beam fusion cutting of 90MnCrV8 was estimated by computing the conductive power loss. Basing on heat affected zone extension experimentally measured and using an inverse methodology approach, the unknown thermal load on the cutting front during laser cutting was calculated. The accuracy of the numerical power loss estimation was evaluated comparing the results from simulation with the ones from analytical models. A good agreement was found for all the test cases considered in this study. The conduction losses estimation was used for justifying the lower quality of disk laser cuts due to the lower average cut front temperature. This results in the increase of viscosity of molten material and in the subsequent more difficult ejection of the melted material from the cut kerf.     

Stress relaxation at crack tip: An alternative to blunting in configurations close to that of the two dimensional approach

Due to geometrical limitations of available slip systems by crystallography, it appears statistically that plastic activity is more likely to take place on planes which cut the crack front (jogging planes) than on planes which contain the crack front (blunting planes), as usually put forward by the 2D models. This paper emphasises the fact that in the absence of increase in the crack tip radius, an enhanced shielding can be achieved through a cross-slip mechanism.Dedicated to Dr. Frantiek Kroupa in honour of his 70^th birthday.The authors were very honored to be invited to participate in this special issue dedicated to Dr. F. Kroupa. This is one of their ways to convey him all of their friendship and respect.     

电容式次声传感器频率特性研究

研究了次声传感器的频率特性的分布情况,定量分析了次声传感器组成部件参数对幅频特性的影响。通过求解次声传感器前后腔内的次声波动态方程得到频率响应模型和截止周期误差模型,选取一批进气口、均压管和膜片相对误差在5%之内的部件,与体积相对误差控制在0.1%之内的前后腔体部件组装成32个次声传感器并对其进行校准实验,校准结果表明该批传感器的截止周期分布在540 s至610 s区间,根据截止周期误差模型计算的理论变化区间范围为530.6 s至614.9 s区间,二者的一致性验证了模型的有效性,为控制次声传感器截止周期一致性和传感器批量精细设计提供了理论指导。      

An energy sum constraint of event mixing for Bose-Einstein correlations in reactions with ππX final states around 1 GeV

We present a new event mixing technique for measuring two-pion Bose-Einstein correlations(BEC)in reactions with only two identical bosons among three final state particles.This new mixing method contains a missing mass consistency(MMC)cut and an energy sum order(ESO)cut.Unlike the previous proposed pion energy cut,which abandons nearly half the original events,the ESO cut does not eliminate any original events and hence improves the statistics of both original events and mixed events.Numerical tests using theγp→π~0π~0p events around1 Ge V are carried out to verify the validity of the ESO cut.This cut is able to reproduce the relative momentum distribution of the original events in the absence of BEC effects.In addition,its ability to observe BEC effects is tested by an event sample in the presence of BEC effects.Simulation results show the BEC effects can be observed clearly as an enhancement in the correlation function,and the BEC parameters extracted by this event mixing cut are consistent with the input BEC parameters.     

Origination and Propagation of the Temperature Front on Crystallization of Ti<Subscript>50</Subscript>Cu<Subscript>50</Subscript> Amorphous Alloy

A kinetic model and mechanism of the origination and propagation of a temperature front in the Ti₅₀Cu₅₀ alloy experiencing an amorphous-to-crystalline transition initiated by a volume thermal source are proposed. The physical reasons and conditions for this phenomenon are considered. The model qualitatively and quantitatively agrees with the experimental data for the propagation of the temperature front.     

Quantitative estimation of thermal contact conductance of a real front‐end component at SPring‐8 front‐ends

The thermal contact conductance (TCC) of a real front‐end component at SPring‐8 has been quantitatively estimated by comparing the results of experiments with those of finite‐element analyses. In this paper one of the methods of predicting the TCC of a real instrument is presented. A metal filter assembly, which is an indirect‐cooling instrument, was selected for the estimation of the TCC. The temperature of the metal filter assembly for the maximum heat load of synchrotron radiation was calculated from the TCC that is expected under normal conditions. This study contributes towards the ongoing research program being conducted to investigate the real thermal limitation of all front‐end high‐heat‐load components.     

Asymmetric transmission through a photorefractive crystal of barium titanate

We have investigated the feasibility of using a barium titanate crystal as a unidirectional device. The nonlinear interaction between a beam and its own reflection from the back face of the crystal causes an effective increase or decrease in the transmission through the crystal, depending on whether the incident beam propagates along or against the crystal c-axis, respectively. This effect was investigated for several wavelengths and compared with theory. It is possible to make a device that has an average transmission of ≈94% and a transmission asymmetry of 1% by using a crystal whose front and back faces are cut so that their normals are at angle of ≈30° to the crystal c-axis.     

Optimization of an off-axis nozzle for assist gas injection in laser fusion cutting

The aerodynamic features of the gas flow during laser fusion cutting are an essential factor influencing the cut performance. For this reason it has been a subject of some studies to explain the interactions of the gas jet with the workpiece and to design different gas injection systems with the aim of preventing the drawbacks of the conventional cutting heads.An off-axis cutting head with a de Laval nozzle to inject a supersonic gas jet has been previously demonstrated to be an effective design to achieve a complete removal of the molten material from the cutting front and to avoid the formation of the recast layer. In the present work, the fundamentals and procedures to adjust the main factors determining the efficiency of this gas injection system are described. Specifically, the gas flow inside the cut kerf is analysed by means of flow visualization using the Schlieren technique.     

Silicon nitride transmission X‐ray mirrors

Transmission X‐ray mirrors have been fabricated from 300–400 nm‐thick low‐stress silicon nitride windows of size 0.6 mm × 85 mm. The windows act as a high‐pass energy filter at grazing incidence in an X‐ray beam for the beam transmitted through the window. The energy cut‐off can be selected by adjusting the incidence angle of the transmission mirror, because the energy cut‐off is a function of the angle of the window with respect to the beam. With the transmission mirror at the target angle of 0.22°, a 0.3 mm × 0.3 mm X‐ray beam was allowed to pass through the mirror with a cut‐off energy of 10 keV at the Cornell High Energy Synchrotron Source. The energy cut‐off can be adjusted from 8 to 12 keV at an angle of 0.26° to 0.18°, respectively. The observed mirror transmittance was above 80% for a 300 nm‐thick film.     

21.2%‐efficient fineline‐printed PERC solar cell with 5 busbar front grid

We evaluate industrial‐type PERC solar cells applying a 5 busbar front grid and fineline‐printed Ag fingers. We obtain finger widths down to 46 µm when using a stencil with 40 µm opening for the finger print, whereas the busbar is printed in a separate printing step with a different Ag paste (dual print). This compares to finger widths of 62 µm to 66 µm when applying print‐on‐print. The 5 busbar front grid with the best dual print process reduces the shadowing loss of the front grid to 4.0% compared to 5.8% for a conventional 3 busbar front grid printed with print‐on‐print. The 1.8% reduction in shadowing loss results in equal parts from the reduced finger width with dual print as well as from a reduced total busbar width of the 5 busbar design. The resulting PERC solar cells with 5 busbars demonstrate independently confirmed conversion efficiencies of 21.2% compared to 20.6% efficiency of the 3 busbar PERC solar cell. The increased conversion efficiency is primarily due to an increased short‐circuit current resulting from the reduced shadowing loss. To our knowledge, 21.2% conversion efficiency is the highest value reported so far for industry typical silicon solar cells with printed metal front and rear contacts. (© 2014 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

On the momentum correlations in the fragmentation of <Superscript>197</Superscript>Au + <Superscript>197</Superscript>Au reactions

We aim to present the formation of fragments using static as well as momentum-dependent interactions and larger nucleonic cross-sections. We shall also examine, in detail, the role of momentum correlations in these situations which are close to the fire-ball as well as to the spectator matter decay. The role of momentum correlations will be studied by imposing an additional cut in the momentum space. A clear need of a momentum cut is demonstrated in both fire-ball as well as spectator matter physics. The momentum-dependent interactions and larger cross-sections play a drastic role in peripheral reactions, whereas the role of momentum cut remains the same in these situations.     

Numerical investigation of hydrodynamics behaviour of melt layer during laser cutting of steel

Understanding of the melt layer hydrodynamic behaviour during laser-cutting process under gas jet assistance is of high importance for cut quality control. In the present work, a numerical model is developed to calculate the three-dimensional behaviour of the melt flow on the kerf front, while an inert gas jet interacts with the melt film. Fluent CFD code is used to solve the governing hydrodynamic equations by finite volume method. The results show that the melt flow on the kerf front reveals a strong instability, which depends on the cutting speed and on the gas jet velocity. Global flow behaviour (gas and molten metal flows) computed using a laminar model, reveals oscillations of the gas–metal liquid interface, which is assimilated to Kelvin–Helmholtz instability. The origin of this instability is discussed in terms of instabilities in thermal dynamics and hydrodynamics. Instability in thermal dynamics is related to the localized melting, while the instability in hydrodynamics is governed by forces balance between gas and resistant surface tension.     

Factory-roof-shaped phase front at the paraelectric-ferroelectric transition in KD PO : an incoherent interface

The phase front during the 218 K transition in KD₂PO₄ crystals under a thermal gradient perpendicular to the c ferroelectric axis is observed to have a factory-roof shape. This shape is studied versus the magnitude of G_e in samples cut with faces in (100), (010), (001) planes or in ( 0), (110), (001) ones. A geometric approach as well as the calculation of the elastic-strain energy caused by lattice misfits along the phase front demonstrate the incoherent interface nature of the phase front. Furthemore, the results and their interpretation allow to predict the sign of the lattice deformation u _xx ( > 0). Received 25 April 2002 Published online 29 November 2002     

Propagation of a reaction front accompanied by island formation: CO/Au/Ni(1 1 1)

Recent high-pressure scanning tunneling microscopy studies, performed at room temperature, have explicitly demonstrated the specifics of the CO-mediated removal of Ni atoms from the topmost layer of an Au/Ni(1 1 1) surface alloy. After an incubation period, the reaction is found to start at step edges. On each edge, a large fraction of Ni atoms is removed from the terrace in certain areas, whereas other areas are nearly intact after a given time. With increasing time, the former areas begin to overlap and the reaction front becomes somewhat more homogeneous. The Au atoms remaining behind the front form nm-sized islands. Here, we present Monte Carlo simulations reproducing all these observations.     

Period stabilization in the Busse–Heikes model of the Küppers–Lortz instability

The Busse–Heikes dynamical model is described in terms of relaxational and non-relaxational dynamics. Within this dynamical picture a diverging alternating period is calculated in a reduced dynamics given by a time-dependent Hamiltonian with decreasing energy. A mean period is calculated which results from noise stabilization of a mean energy. The consideration of spatial-dependent amplitudes leads to vertex formation. The competition of front motion around the vertices and the Küppers–Lortz instability in determining an alternating period is discussed.     

Pixelated transmission‐mode diamond X‐ray detector

Fabrication and testing of a prototype transmission‐mode pixelated diamond X‐ray detector (pitch size 60–100 µm), designed to simultaneously measure the flux, position and morphology of an X‐ray beam in real time, are described. The pixel density is achieved by lithographically patterning vertical stripes on the front and horizontal stripes on the back of an electronic‐grade chemical vapor deposition single‐crystal diamond. The bias is rotated through the back horizontal stripes and the current is read out on the front vertical stripes at a rate of ～1 kHz, which leads to an image sampling rate of ～30 Hz. This novel signal readout scheme was tested at beamline X28C at the National Synchrotron Light Source (white beam, 5–15 keV) and at beamline G3 at the Cornell High Energy Synchrotron Source (monochromatic beam, 11.3 keV) with incident beam flux ranges from 1.8 × 10^?2 to 90 W mm^?2. Test results show that the novel detector provides precise beam position (positional noise within 1%) and morphology information (error within 2%), with an additional software‐controlled single channel mode providing accurate flux measurement (fluctuation within 1%).     

Silicon carrier depletion modulator with 10 Gbit/s driver realized in high‐performance photonic BiCMOS

Optical modulators based upon carrier depletion have proven to be effective at achieving high speed operation in silicon. However, when incorporated into Mach‐Zehnder Interferometer structures they require electronic driver amplifiers to provide peak to peak drive voltages of a few volts in order to achieve a large extinction ratio. For minimal performance degradation caused by the electrical connection between the driver and the modulator monolithic integration in the front end of the process is the preferred integration route. The formation of electronic driver amplifiers in BiCMOS is advantageous over CMOS in terms of achievable performance versus cost. In this work the first monolithic photonic integration in the electronic front‐end of a high‐performance BiCMOS technology process is demonstrated. Modulation at 10 Gbit/s is demonstrated with an extinction ratio >8 dB. The potential scalability of both the silicon photonic and BiCMOS elements make this technology an attractive prospect for the future.     

Possibility of X‐ray pulse compression using an asymmetric or inclined double‐crystal monochromator

It is shown theoretically that the asymmetric or inclined double‐crystal X‐ray monochromator may be used for X‐ray pulse compression if the pulse is properly chirped. By adjusting the mutual distance of the two asymmetric or inclined crystals it should be possible to achieve even a sub‐femtosecond compression of a chirped free‐electron laser pulse. The small d‐spacing of the crystal enables a more compact scheme compared with the currently used grating compression scheme. The asymmetric cut of the crystal enables the acceptance of a larger bandwidth. The inclined cut has larger tunability.     

一款超薄800万像素手机镜头的设计

为了满足市场对超薄手机镜头的要求,运用光学软件CODEV,结合非球面理论,设计一款新的超薄800万像素手机镜头。该镜头由4片非球面塑料镜片,1片滤光镜片和1片保护玻璃组成,其中第1片透镜是正透镜,第2片镜片是负透镜,第3片镜片是正透镜,第4片镜片是负透镜,且光阑位于第1片透镜的前面。镜头光圈值F为2.4,视场角2为65.5,焦距为3.731 5 mm,后焦距0.31 mm,镜头总长度为4.6 mm,在最高频率1/2处大多数视场的MTF值均大于0.5,畸变小于2% 。