Polymer drying. VI. EPR spin-probe studies on swelled poly(styrene-co-divinylbenzene)

The electron paramagnetic resonance (EPR) signal and the residual number (α_t) of volatile molecules per phenyl group of poly(styrene-co-divinylbenzene) in samples that had been swelled to saturation in a dilute solution of a nitroxide spin-probe (TEMPO or 4-oxo-TEMPO), dissolved in a volatile liquid, were monitored simultaneously as the system containing excess liquid was allowed to evaporate to dryness. The results showed that the characteristic motionally narrowed three-line EPR spectrum began to change when α_t became equal to α_g (the number of sorbed molecules per phenyl group of polymer at liquid-saturation). The ratio of the intensity of the low-field and high-field hyperfine peaks relative to the middle peak decreased monotonically to an asymptotic limit that was attained when α_t became equal to α_g (the number of residual adsorbed molecules per phenyl group of polymer at completion of the transition from the rubbery state to the glassy state). The EPR hyperfine pattern, from which the rotational correlation times were estimated, changed most significantly as α_t decreased from α_G to α_g while exhibiting inflections at about α′_s and α′_g the compositions that mark, respectively, incipient desorption of adsorbed molecules and incipient transition from the rubbery state to the glassy state. The pattern between these inflections points, however, varied with the affinity of the solvent for the polymer.     

Correlation of SiO x layer thickness and properties of BOPP/SiO x composite films with spin coating process parameters

The effects of the spin coating process parameters on the thickness of the SiOx layer of the BOPP/SiOx composite film were investigated. When the concentration of tetraethoxysilane (TEOS) increased from 12.5 vol% to 55% vol%, the SiOx thickness increased from about 80 nm to 470 nm. In the sol time range of 1.5 h to 5 h the SiOx layer thickness reached a maximum at about 4 h and the change of the thickness roughly matched the change of the silica colloidal sphere sizes in sol. When the spin-coating speed of the dispensing stage increased from 450 r/min to 500 r/min, the SiOx layer thickness drastically decreased from about 1.67 μm to 400 nm. While the spin-coating speed of the thinning and drying stage went up to 1200 r/min, the SiOx layer thickness was in the range of 330 nm to 390 nm. It was also found that the SiOx layer thickness was almost increased linearly from about 500 nm to 1.02 μm with the ratio of the commercial silica colloidal to the TEOS from 0.2 to 1.0. The water contact angles decreased to about 23.0° for the BOPP/Si-Sol composite film with 1.67 μm SiOx layer and about 4.0° for the BOPP/mixing Si-Sol composite film with 1.02 μm SiOx layer. Compared to BOPP, the light transparency of the BOPP/Si-Sol composite films decreased by about 5.5% with the SiOx layer from about 80 nm to 1.67 μm and by 7.0% for the BOPP/mixing Si-Sol composite film with the SiOx layer from about 350 nm to 1.02 μm respectively.     

Detoxification of antimony by selenium and their interaction in paddy rice under hydroponic conditions

Antimony (Sb) contamination has become a growing concern in recent years. Strategies for reducing Sb contamination and its related health risks are urgently desired. This study was conducted to explore the possibility of selenium (Se) detoxification on Sb toxicity in paddy rice in order to find a feasible method to reduce the health risk of Sb pollution. Seedlings of paddy rice were exposed to 5 mg L⁻¹ Sb (KSbC₄H₄ O₇·1/2H₂O), in the presence of Se (Na₂SeO₃) at 0.1, 1, 5 mg L⁻¹ in culture solution, with no Sb and Se addition as the control. Paddy rice took up Sb greatly and the highest Sb contents measured among all treatments in this experiment in the leaves, stems and roots were 65.5, 298.5 and 195.7 mg kg⁻¹, respectively. Without Sb addition in the solution, single exposure to 0.1 mg L⁻¹ Se remarkably reduced the malondialdehyde (MDA) formation in paddy rice,demonstrating the beneficial effect of Se at low dosages. The addition of 5 mg L⁻¹ Sb was found to generate toxicity to paddy rice, showing as decreased biomass and increased leaf MDA content in paddy rice, while addition of 1 mg L⁻¹ Se mitigated the toxicity of Sb, as seen with the decreased leaf MDA content and increased biomass, indicating antidotal role of Se to Sb. In addition, the presence of 0.1, 1, 5 mg L⁻¹ Se generally decreased the accumulation of Sb in the leaves, stems and roots in paddy rice. Toxicity was also seen when paddy rice was exposed to single Se at 1 and 5 mg L⁻¹ levels, however, 5 mg L⁻¹ Sb addition was found to decrease the contents of Se in the leaves/stems whereas increased them in roots, accompanied with decreased MDA contents and increased biomass in paddy rice, indicating a possible detoxification role of Sb to Se too. Therefore, Sb, although toxic, could also be an antitoxin to Se in paddy rice at certain condition. Our results showed that Se could alleviate Sb toxicity efficiently in paddy rice through two effects as antagonism and antioxidation.     

Fluorescence quantification of tetracycline in the presence of quenching matrix effect by means of a four-way model

In this work, a four-way tensor is used to model the quenching effect in fluorescent measurements. By means of the analysis of excitation-emission matrices obtained in the determination of tetracycline in tea, which acts as quencher, it is shown as the impossibility to use a calibration, or an addition standard based on a three-way model. It is analysed the quencher multiplicative effect made on the tetracycline signal by means of an ANOVA. However, by arranging the experimental data in a four-way tensor, it is viable to perform a calibration based on the parallel factor analysis, PARAFAC, decomposition and a four-way partial least squares, 4-PLS, regression to quantify the tetracycline in the presence of the matrix quencher effect. 4-PLS calibration provides better results. In the range from 40 to 220 μg L⁻¹ gives an average of relative errors in absolute value equal to 8.02% in prediction (3.40% in calibration). The repeatability as standard deviation in this range is 5.08 μg L⁻¹ and the method is accurate, slope and intercept being statistically equal to 1 and 0, respectively when a regression calculated versus true concentration is performed. Moreover, it has a decision limit (CCα) of 13.87 μg L⁻¹ for a probability of false positive, α, equal to 0.05 and a capability of detection (CCβ) of 26.63 μg L⁻¹ (for probabilities of false positive, α, false negative, β, equals to 0.05).     

Water Reduction and Dihydrogen Addition in Aqueous Conditions With ansa-Phosphinoborane

Ortho-phenylene-bridged phosphinoborane (2,6-Cl₂Ph)₂B-C₆H₄-PCy₂ 1 was synthesized in three steps from commercially available starting materials. 1 reacts with H₂ or H₂O under mild conditions to form corresponding zwitterionic phosphonium borates 1-H₂ or 1-H₂O . NMR studies revealed both reactions to be remarkably reversible. Thus, when exposed to H₂, 1-H₂O partially converts to 1-H₂ even in the presence of multiple equivalents of water in the solution. The addition of parahydrogen to 1 leads to nuclear spin hyperpolarization both in dry and hydrous solvents, confirming the dissociation of 1-H₂O to free 1 . These observations were supported by computational studies indicating that the formation of 1-H₂ and 1-H₂O from 1 are thermodynamically favored. Unexpectedly, 1-H₂O can release molecular hydrogen to form phosphine oxide 1-O . Kinetic, mechanistic, and computational (DFT) studies were used to elucidate the unique “umpolung” water reduction mechanism.     

Polymerization effects on molecular dynamics of n-ethylene glycol dimethacrylates followed by dielectric relaxation spectroscopy

A detailed dielectric characterization of n-ethylene glycol dimethacrylate monomers with n = 2 and 4 is provided. Besides the α relaxation associated to the glass transition, two secondary relaxation processes were detected: the γ process assigned to the twisting motions within the ethylene glycol moiety, and the β process related with hindered rotations of carboxylic groups. While the relaxation time of the γ process is independent of the size of the ethylene glycol group, the β process deviates to higher times with increasing n. Upon polymerization the α process goes to extinction, faster in the 4-ethylene monomer, with a concomitant depletion of the β process that remains at higher polymerization degrees relatively to the α process, thus acting as a more sensitive probe to evaluate conversion. The height decrease of α and β processes of monomers with the polymerization progress, occurs without significant changes of position. At intermediate states of polymerization, a new relaxation process evolves being only detectable in a narrow temperature range. In the end, the polymer networks show, in addition to the γ_pol relaxation identical to the γ relaxation of the monomer, a β_pol relaxation with similar features to the β relaxation found in poly n-alkyl methacrylates originated by a π flip of the ester unit accompanied by a restricted main chain rearrangement. The main dielectric relaxation corresponding to the swollen polymer network should appear at quite high temperatures already in early stages of the polymerization process because phase segregation occurs and only a limited amount of liquid monomer plasticizes the newly formed material.     

An interlaboratory study as useful tool for proficiency testing of chemical oxygen demand measurements using solid substrates and liquid samples with high suspended solid content

In 2008, the first Proficiency Testing Scheme of Chemical Oxygen Demand (1^stCOD-PT^ADG) was conducted to assess the results obtained for different research groups whose field work is mainly anaerobic digestion. This study was performed using four samples, two solid samples as raw materials and two solid samples to prepare high concentration suspended solid solutions. Invitations were sent to a large number of laboratories, mainly to anaerobic digestion research groups. Finally, thirty labs from sixteen countries agreed to participate, but for different reasons four participants could not send any data. In total, twenty-six results were reported to the COD-PT coordinator.This study showed the importance of continuous participation in proficiency testing (PT) schemes in order to compare the results obtained. Taking into account the lack of a general standard method and high quality certified reference materials (CRMs), the traceability of COD determination is not currently easy to check. In addition, the spread of participants’ results obtained was high and pointed to the advisability of using consensus values due to their unreliability. Therefore, the theoretical oxygen demand (ThOD) values were considered as assigned values for all the samples analysed. On the other hand, in this PT the established standard deviation (ESD) has been determined by the Horwitz modified function.Participants of this 1^stCOD-PT^ADG were asked to give a short report on the analytical method used. Although all the participants used potassium dichromate as their oxidant reagent, their experimental procedures were very different. With the purpose of comparing the results obtained, the different experimental conditions used were classified into five methods, corresponding to two main categories, open and closed reflux. The performance of laboratories was expressed by the z-score, whose value is considered satisfactory when z-score ≤±2. The overall analytical data evaluation showed that 64% of z-scores obtained were outside the accepted limits.     

Acyl radical addition to benzene and related systems—a computational study

The addition of the acetyl radical to benzene, aniline, trifluoromethylbenzene and naphthalene has been investigated using DFT calculations. Addition to benzene is calculated to have an energy barrier of 63.6 kJ mol⁻¹ at the BHandHLYP/6-311G(d,p)+ZPE level of theory. This reaction is associated with simultaneous SOMO→π^∗ and π→SOMO interactions with the latter interaction dominating, suggesting that acetyl reacts predominantly as an electrophilic radical in its interaction with benzene. Addition to the ortho and para positions of aniline is calculated to be slightly less favourable, while attack at the meta position is predicted to be unaffected in relation to the chemistry involving benzene. Inclusion of the electron-withdrawing substituent, trifluoromethyl, is predicted to accelerate reactions slightly at the ortho and para positions, while attack at the C1 position of naphthalene is calculated to involve a barrier of 50.3 kJ mol⁻¹ (BHandHLYP/6-311G(d,p)+ZPE).     

Glucose-induced heat production, insulin secretion and lactate production in isolated Wistar rat pancreatic islets

Transplantation of pancreatic islets is efficient in improving the metabolic control and quality of life and in preventing severe hypoglycemia in patients with brittle type 1 diabetes mellitus. More accurate methods to assess islet viability would be extremely useful in designing target interventions for islet cytoprotection and in reducing the number of islets required to achieve insulin independence. Here we report on an application of calorimetry to evaluate the metabolic response of pancreatic islets to glucose stimulation. A significant increase in metabolic heat was produced by islet samples when consecutively subjected to 2.8 and 16.3 mmol L⁻¹ glucose. Under these glucose concentrations, 1000 islets released average heat values of 9.16 ± 0.71 mJ and 14.90 ± 1.21 mJ over 50 min, respectively. Additionally, the glucose stimulation indexes were 1.67 ± 0.30 for insulin, 1.72 ± 0.13 for heat and 2.91 ± 0.50 for lactate, raising the important possibility of substituting the secreted insulin index/ratio by the index/ratio of the heat released in the evaluation of Langerhans islets viability for transplantation. Altogether, our results demonstrate the applicability of calorimetry to assess the quality of isolated pancreatic islets and to study vital islet functions.     

Beyond p-Hexaphenylenes: Synthesis of Unsubstituted p-Nonaphenylene by a Precursor Protocol

The synthesis of unsubstituted oligo-para-phenylenes ( OPP ) exceeding para-hexaphenylene—in the literature often referred to as p-sexiphenyl—has long remained elusive due to their insolubility. We report the first preparation of unsubstituted para-nonaphenylenes ( 9PP s) by extending our precursor route to poly-para-phenylenes ( PPP ) to a discrete oligomer. Two geometric isomers of methoxylated syn- and anti-cyclohexadienylenes were synthesized, from which 9PP was obtained via thermal aromatization in thin films. 9PP was characterized via optical, infrared and solid-state ¹³C NMR spectroscopy as well as atomic force microscopy and mass spectrometry, and compared to polymeric analogues. Due to the lack of substitution, para-nonaphenylene, irrespective of the precursor isomer employed, displays pronounced aggregation in the solid state. Intermolecular excitonic coupling leads to formation of H-type aggregates, red-shifting emission of the films to greenish. 9PP allows to study the structure–property relationship of para-phenylene oligomers and polymers, especially since the optical properties of PPP depend on the molecular shape of the precursor.     

Structure and Magnetic Properties of Nickel–Zinc Ferrite Nanoparticles Prepared by Glass Crystallization Method

Summary. The magnetic and microstructure properties of Fe₂O₃–0.4NiO–0.6ZnO–B₂O₃ glass system, which was subjected to heat treatment in order to induce a magnetic crystalline phase (Ni_0.4Zn_0.6-Fe₂O₄ crystals) within the glass matrix, were investigated. DSC measurement was performed to reveal the crystallization temperature of the prepared glass sample. The obtained samples, produced by heat treatment at 765°C for various times (1, 1.5, 2, and 3 h), were characterized by X-ray diffraction, IR spectra, transmission electron microscopy, and vibrating sample magnetometer. The results indicated the formation of spinel Ni–Zn ferrite in the glass matrix. Particles of the ferrite with sizes ranging from 28 to 120 nm depending on the sintering time were observed. The coercivity values for different heat-treatment samples were found to be in the range from 15.2 to 100 Oe. The combination of zinc content and sintering times leads to samples with saturation magnetization ranging from 12.25 to 17.82 emu/g.     

A new multiresponse optimization approach in combination with a D-Optimal experimental design for the determination of biogenic amines in fish by HPLC-FLD

A new strategy to approach multiresponse optimization in conjunction to a D-optimal design for simultaneously optimizing a large number of experimental factors is proposed. The procedure is applied to the determination of biogenic amines (histamine, putrescine, cadaverine, tyramine, tryptamine, 2-phenylethylamine, spermine and spermidine) in swordfish by HPLC-FLD after extraction with an acid and subsequent derivatization with dansyl chloride. Firstly, the extraction from a solid matrix and the derivatization of the extract are optimized. Ten experimental factors involved in both stages are studied, seven of them at two levels and the remaining at three levels; the use of a D-optimal design leads to optimize the ten experimental variables, significantly reducing by a factor of 67 the experimental effort needed but guaranteeing the quality of the estimates. A model with 19 coefficients, which includes those corresponding to the main effects and two possible interactions, is fitted to the peak area of each amine. Then, the validated models are used to predict the response (peak area) of the 3456 experiments of the complete factorial design. The variability among peak areas ranges from 13.5 for 2-phenylethylamine to 122.5 for spermine, which shows, to a certain extent, the high and different effect of the pretreatment on the responses. Then the percentiles are calculated from the peak areas of each amine. As the experimental conditions are in conflict, the optimal solution for the multiresponse optimization is chosen from among those which have all the responses greater than a certain percentile for all the amines. The developed procedure reaches decision limits down to 2.5 μg L⁻¹ for cadaverine or 497 μg L⁻¹ for histamine in solvent and 0.07 mg kg⁻¹ and 14.81 mg kg⁻¹ in fish (probability of false positive equal to 0.05), respectively.     

Modification of surface properties of oral streptococci by α-1,6 glucans

Several members of the genus Streptococcus, including S. sobrinus, S. cricetus, S. sanguis and S. mutans, are known to produce proteins capable of complexing with α-1,6 glucans. Of all the oral streptococcal groups, S. sobrinus and S. cricetus are the most readily aggregated by high molecular weight glucan (glucan T-2000), but the aggregation may be inhibited by low molecular weight glucans (glucan T-10). Some of the oral streptococci are also known to express surface hydrophobins, molecules which impart hydrophobic characteristics to their cell surfaces. When glucan T-10 was added to suspensions of S. cricetus or S. sobrinus, the bacteria were less able to adhere to hexadecane, to bind to plastics or to be aggregated by ammonium sulfate. It is concluded that the glucan rendered the bacteria more hydrophilic. In contrast, streptococci such as S. sanguis and S. mutans, incapable of aggregation by high molecular weight α-1,6 glucan, retained their hydrophobic characteristics in the presence of glucan T-10. Other bacteria, such as Bacillus subtilis, Escherichia coli and Pseudomonas aeruginosa, exhibited their same abilities to bind to hexadecane, to adhere to plastics or to be aggregated by ammonium sulfate, regardless of the presence of α-1,6 glucan. When S. cricetus or S. sobrinus were grown under conditions to minimize expression of glucan-binding lectin or when glucan-binding lectin was denatured, glucan T-10 had no effect on their hydrophobic characteristics. It appears that the complexing of α-1,6 glucan by streptococci bearing glucan-binding lectin causes the bacteria to assume a more hydrophilic character.     

Influence of the Lanthanide Ion and Solution Conditions on Formation of Lanthanide Wells–Dawson Polyoxotungstates

Lanthanide complexes of polyoxometalates, including the α₂-P₂W₁₇O₆₁ ¹⁰⁻ ligand, have been pioneered by Michael T. Pope, to whom this paper is dedicated. Examination of the solid-state and solution behavior of lanthanide complexes of the α₂-P₂W₁₇O₆₁ ¹⁰⁻ ligand are reported here to identify trends that will facilitate rational synthesis of hybrid organic lanthanide polyoxometalate complexes. Therefore, combining our data with that obtained by Pope and others a number of trends come into view. It is clear that there are two structural types for the 1:1 or 2:2 [Ln(H₂O)_X(α₂-P₂W₁₇O₆₁)]₂ ¹⁴⁻ species. The early lanthanides show a “cap to cap” structure that allows the Ln ion to be 9 coordinate and accommodates the longer bond lengths. The mid-late lanthanides show a “cap to belt” structure that allows the lanthanides to be 8 coordinate; this structural type is appropriate for the shorter bond lengths of the later lanthanides. The 1:1⇌1:2 equilibrium, that was observed by Pope for the Ce(III) analog is prevalent for the early- mid lanthanides. This equilibrium is slightly dependent on pH; however, cations have a major influence on this equilibrium. Larger, poorly hydrated cations appear to favor the 1:2 species for the early to mid lanthanides. Cations do not appear to influence the equilibrium for the later lanthanides; for all counterions, the 1:1 species was stable with no trace of the 1:2 species. Stability constants, K1 and K2, for the early to mid lanthanides were measured in this study by a competitive method and compared well with other published stability constant determinations. We suggest that the stability constants are not only dependent on the strength of interaction of the Ln with the α₂-P₂W₁₇O₆₁ ¹⁰⁻ ligand, but are also significantly influenced by the medium. The medium may bias the equilibria of the early-mid lanthanides and later lanthanides. The log K₁/log K₂ ratios are very close, suggesting that it is difficult to separate the 1:1 and 1:2 Ln: α₂-P₂W₁₇O₆₁ ¹⁰⁻ species.Electronic Supplementary Material Supplementary material for this article is available at and is accessible for authorized users.This paper is dedicated to Professor Michael T. Pope in honor of his substantial and sustained contributions to polyoxometalate chemistry and his inspiration to scientists working in the field.     

Diels–Alder and Retro‐Diels–Alder Cycloadditions of (1,2,3,4,5‐Pentamethyl)cyclopentadiene to La@C2v‐C82: Regioselectivity and Product Stability

One of the most important reactions in fullerene chemistry is the Diels–Alder (DA) reaction. In two previous experimental studies, the DA cycloaddition reactions of cyclopentadiene (Cp) and 1,2,3,4,5‐pentamethylcyclopentadiene (Cp*) with La@C_2v‐C₈₂ were investigated. The attack of Cp was proposed to occur on bond 19 , whereas that of Cp* was confirmed by X‐ray analysis to be over bond o . Moreover, the stabilities of the Cp and Cp* adducts were found to be significantly different, that is, the decomposition of La@C_2v‐C₈₂Cp was one order of magnitude faster than that of La@C_2v‐C₈₂Cp*. Herein, we computationally analyze these DA cycloadditions with two main goals: First, to compute the thermodynamics and kinetics of the cycloadditions of Cp and Cp* to different bonds of La@C_2v‐C₈₂ to assess and compare the regioselectivity of these two reactions. Second, to understand the origin of the different thermal stabilities of the La@C₈₂Cp and La@C₈₂Cp* adducts. Our results show that the regioselectivity of the two DA cycloadditions is the same, with preferred attack on bond o . This result corrects the previous assumption of the regioselectivity of the Cp attack that was made based only on the shape of the La@C₈₂ singly occupied molecular orbital. In addition, we show that the higher stability of the La@C₈₂Cp* adduct is not due to the electronic effects of the methyl groups on the Cp ring, as previously suggested, but to higher long‐range dispersion interactions in the Cp* case, which enhance the stabilization of the reactant complex, transition state, and products with respect to the separated reactants. This stabilization for the La@C₈₂Cp* case decreases the Gibbs reaction energy, thus allowing competition between the direct and retro reactions and making dissociation more difficult.     

Determination of iodide by detection of iodine using gas-diffusion flow injection and chemiluminescence

This work describes development of a flow injection (FI) system for determination of iodide, based on the chemiluminescence (CL) reaction between iodine and luminol. Iodide in the sample zone is oxidized to iodine. Employment of a gas-diffusion (GD) unit allows for selective detection of the generated CL (425 nm). Preliminary results showed for concentrations of less than 2 mg L⁻¹, that signals were irreproducible and that the calibration was not linear.In order to solve these problems, a method of ‘membrane conditioning’ was investigated, in which iodide stream was continuously merged with oxidant to generate I₂ that conditioned the GD membrane and tubing. This minimized surface interaction between the active surface and the I₂ generated from the samples, thus improving both precision and sensitivity. By employing membrane conditioning, it has been possible to reliably detect concentrations down to 0.1 mg L⁻¹.At the optimized condition, an excellent linear calibration (r² = 0.999) was obtained from 0.1 to 1.0 mg L⁻¹. The method was successfully applied to determine iodide in some pharmaceutical products such as potassium iodide tablets and a liquid patent medicine. However, for vitamin tablets, ascorbic acid was found to interfere seriously by causing a negative signal.     

Systematic Study of Selected Diagonalization Methods for Configuration Interaction Matrices

Several modifications to the Davidson algorithm are systematically explored to establish their performance for an assortment of configuration interaction (CI) computations. The combination of a generalized Davidson method, a periodic two‐vector subspace collapse, and a blocked Davidson approach for multiple roots is determined to retain the convergence characteristics of the full subspace method. This approach permits the efficient computation of wave functions for large‐scale CI matrices by eliminating the need to ever store more than three expansion vectors ( b _i) and associated matrix‐vector products ( σ _i), thereby dramatically reducing the I/O requirements relative to the full subspace scheme. The minimal‐storage, single‐vector method of Olsen is found to be a reasonable alternative for obtaining energies of well‐behaved systems to within μE_h accuracy, although it typically requires around 50% more iterations and at times is too inefficient to yield high accuracy (ca. 10^?10 E_h) for very large CI problems. Several approximations to the diagonal elements of the CI Hamiltonian matrix are found to allow simple on‐the‐fly computation of the preconditioning matrix, to maintain the spin symmetry of the determinant‐based wave function, and to preserve the convergence characteristics of the diagonalization procedure. © 2001 John Wiley & Sons, Inc. J Comput Chem 22: 1574–1589, 2001     

Sensitive and selective detection of aspartic acid and glutamic acid based on polythiophene-gold nanoparticles composite

In recent years, gold nanoparticles and water-soluble fluorescent conjugated polymers are promising materials in terms of their potential applications in a variety of fields, ranging from monitoring DNA hybridization to demonstrate the interaction between proteins, or detecting diseased cell, metal ions and small biomolecular. In order to exploit some new properties of the both, many attempts have been devoted to achieve nanoparticle-polymer composite via incorporating metal nanoparticle into polymer or vice versa, however, only few of them are put into practical application. In the present paper, we utilize the “superquenching” property of AuNPs to polythiophene derivatives for detecting aspartic acid (Asp) and glutamic acid (Glu) in pure water, and discuss the factors accounting for fluorescence quenching and recovery via modulating pH. Thus an exceptionally simple, rapid and sensitive method for detecting Asp and Glu is established with a limit of detection (LOD) is 32 nM for Asp and 57 nM for Glu, the linear range of determination for Asp is 7.5 × 10⁻⁸ M to 6 × 10⁻⁶ M and 9.0 × 10⁻⁸ M to 5 × 10⁻⁶ M for Glu. The system is applied to real sample detection and the results are satisfying. Otherwise the composite is very sensitive to pH change of solution, we expect it will be possible to use as pH sensor with wide range in the future.     

Development of a switchable multidimensional/comprehensive two-dimensional gas chromatographic analytical system

In this study, a new system for analysis using a dual comprehensive two-dimensional gas chromatography/targeted multidimensional gas chromatography (switchable GC × GC/targeted MDGC) analysis was developed. The configuration of this system not only permits the independent operation of GC, GC × GC and targeted MDGC analyses in separate analyses, but also allows the mode to be switched from GC × GC to targeted MDGC any number of times through a single analysis. By incorporating a Deans switch microfluidics transfer module prior to a cryotrapping device, the flow stream from the first dimension column can be directed to either one of two second dimension columns in a classical heart-cutting operation. Both second columns pass through the cryotrap to allow solute bands to be focused and then rapidly remobilized to the respective second columns. A short second column enables GC × GC operation, whilst a longer column is used for targeted MDGC. Validation of the system was performed using a standard mixture of compounds relevant to essential oil analysis, and then using compounds present at different abundances in lavender essential oil. Reproducibility of retention times and peak area responses demonstrated that there was negligible variation in the system over the course of multiple heart-cuts, and proved the reliable operation of the system. An application of the system to lavender oil, as a more complex sample, was carried out to affirm system feasibility, and demonstrate the ability of the system to target multiple components in the oil. The system was proposed to be useful for study of aroma-impact compounds where GC × GC can be incorporated with MDGC to permit precise identification of aroma-active compounds, where heart-cut multidimensional GC-olfactometry detection (MDGC-O) is a more appropriate technology for odour assessment.     

Nanostructured cupric oxide electrode: An alternative to amperometric detection of carbohydrates in anion-exchange chromatography

In this paper, a new and low cost copper/cupric oxide nanostructured electrode is presented as an alternative to the amperometric detection of carbohydrates in high-performance anion exchange chromatography. The modified copper electrodes were prepared by a simple and fast method which resulted in the obtainment of homogeneously distributed nanostructures adhered to the surface with controlled chemical nature. The results, when compared to conventional copper electrodes, exhibited considerable improvements in analytical results, including: 1) Better repeatability in consecutive glucose detections, in which the percent relative standard deviation improved from 15.1% to 0.279%. 2) Significant improvements in the stability of the baseline and a decrease of the stabilization time, going from several hours to approximately 15 min. 3) Considerable increase in the sensitivity towards glucose, from 5.02 nA min mg L⁻¹ to 25.5 nA min mg L⁻¹. 4) Improvements in the detectability with limits as low as 1.09 pmol. 5) Wide working range of concentrations (1 × 10⁻² to 1 × 10⁴ mg L⁻¹). 6) Good linearity with correlation coefficients greater than 0.998. 7) Possibility of detecting different molecules of carbohydrates (lactose, maltose, sucrose cellobiose, sorbitol, fructose, glucose, galactose, manose, arabitol, xylose, ribose and arabnose). In comparison to the electrode that is more employed for this type of application (gold electrode), the low cost, the possibility of detection at constant potential and the equivalent detection limits presented by the new electrode material introduced in this work emerge as characteristics that make this material a powerful alternative considering the detection of carbohydrates in anion exchange chromatography.